Transcript
A M P I R E
SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO.
AM-128128RTNQW-D1H
APPROVED BY DATE Approved For Specifications Approved For Specifications & Sample
APPROVED BY
Date : 2006/7/14
CHECKED BY
AMPIRE CO., LTD.
ORGANIZED BY
1
RECORD Revision Date Page 2005/05/12 2005/05/17 2005/05/17 2005/07/04 2005/07/04 2005/07/07 2005/07/07 2005/07/26 2005/07/26 2005/07/26 2005/07/26 2005/07/28 2005/07/29 2005/08/29 2005/08/29 2005/08/29 2005/08/30 2005/09/09 2005/09/14 2005/09/14 2005/09/20 2005/09/20 2005/09/21 2005/09/21 2005/09/26 2005/09/26 2005/09/26 2005/09/26 2005/09/26 2005/10/03 2005/10/18 2005/10/18 2006/01/11 2006/02/13 2006/02/15 2006/04/19 2006/07/14
Date : 2006/7/14
15 8 3 34 15 34 35 37 38 14 14 14 14 34 33 34 34 14 33 14 34 33 14 34 33 14 33 14 34 33 14 34 39 14 14 14
OF
REVISION Contents
Editor
New Release
Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil Emil
Addition part list. Modify LED Brightness of main and sub. RoHS declaration. Modify Mechanical drawing. Modify Part List. Modify Mechanical drawing. Including SMD Drawing. Including BLU Drawing. Including Packing Condition. Modify Part List. Modify Part List. Modify Part List. Modify Part List. Modify Mechanical Drawing. Modify Circuit Drawing. Modify Mechanical Drawing. Modify Mechanical Drawing. Modify Part List. Modify Circuit Drawing. Modify Part List. Modify Mechanical Drawing. Modify Circuit Drawing Modify Part List Modify Mechanical Drawing. Modify Circuit Drawing Modify Part List. Modify Circuit Drawing Modify Part List Modify Mechanical Drawing. Modify Circuit Drawing Modify Part List. Modify Mechanical Drawing. Attach Tail FPC Drawing and Improve Action Modify Part List. Modify Part List.(C2,C39Î10u/6.3V, 0805, 0.85t) Remove C16.
AMPIRE CO., LTD.
2
Contents Item
Title
Page
1
Features
4
2
Mechanical Specifications
5
3
Absolute Max. Ratings and Environment
5
4
Electrical Specifications
6
5
Optical Characteristics
7
6
Block Diagram
12
7
Part List
14
8
Interface Specifications
16
9
80-system 16-bit interface
17
10
Instruction Description
18
11
Timing Characteristic
22
12
Setup of Power Supply
24
13
Instruction Setup Flow
25
14
Quality and Reliability
27
15
Use Precautions
31
16
Circuit Drawing
33
17
Outline Dimension
34
18
SMD Drawing
35
19
BLU Drawing
37
20
Tail FPC Drawing and Improve Action
38
21
Packing Condition
40
Date : 2006/7/14
AMPIRE CO., LTD.
3
1
Features
Main LCD 1.5 inch Amorphous-TFT-LCD (Thin Film Transistor Liquid Crystal Display) for mobile-phone or handy electrical equipments. The Main-LCD adopts one backlight with High brightness 3-lamps white LED. (1) Construction: 1.5” a-Si color TFT-LCD, 96×64 Monochromatic FSTN LCD, B/E Chip, FPC, White LED Backlight and Flash LED. (2) Main LCD : 2.1 Amorphous-TFT 1.5 inch display, transmissive, Normally white type, 12 o’clock. 2.2 128(RGB)×128 dots Matrix,1/128 Duty. 2.3 LCD controller is TL1771. 2.4 Real 262K colors display: 65K: Red-5bit, Green-6bit, Blue-5bit (16-bit interface) 262K: Red-6bit, Green-6bit, Blue-6bit (18-bit interface) (3) Sub LCD : 2.1 Monochromatic FSTN type, Transflective, Positive , 6 o’clock view 2.2 96X64 dots matrix, 1/64 Duty. 2.3 Sub LCD controller is S6B0724. (4) 16-bit high speed bus interface and high speed RAM-write function. (5) Direct data display with display RAM. Main LCD Internal RAM capacity: 128×(5+6+5)×128/8=32,768bytes (6) MPU interface: 16 bits 80-serise parallel interface is available. (7) RoHS declaration.
Date : 2006/7/14
AMPIRE CO., LTD.
4
2 Mechanical Specification Dimensions and weight Item External shape dimensions Main LCD
Sub LCD
Specifications
Unit
* 31.4 (W) x 55.68(H) x 3.3 (D) Max.
mm
Pixel pitch
0.204 (W) x 0.22 (H)
mm
Active area
26.112 (W) x 28.16 (H)
mm
Viewing area
28.3 (W) x 30.17 (H)
mm
Dot size
0.195 (W) x 0.21 (H)
mm
Dot pitch
0.21 (W) x 0.225 (H)
mm
Active area
14.385 (W) x 20.145 (H)
mm
Viewing area
16.8 (W) x 22.6 (H)
mm
9.75
g
Weight
* This specification is about External shape on shipment from AMPIRE.
3
Absolute Max. Ratings and Environment 3-1 Absolute max. ratings Ta=25oC GND=0V Item Power Supply for Logic Power Input Voltage Power Supply backlight Input voltage
for
Symbol
Min.
Max.
Unit
VCC – VSS
-0.3
+4.6
V
Vci
-0.3
+4.6
V
-0.5
+10.8
V
-0.5
VDD+0.5
V
LED LED A – LED K VIN
Remarks
3-2 Environment Item Storage temperature
Specifications Max. +80 oC Min. –30 oC
Remarks Note 1: Non-condensing
Max. +70 oC Note 1: o Non-condensing Min. -20 C Note 1：Ta≦+40 oC・・・・Max.85%RH Ta＞+40 oC・・・・The max. humidity should not exceed the humidity with 40 oC 85%RH. Operating temperature
Date : 2006/7/14
AMPIRE CO., LTD.
5
4
Electrical Specifications 4-1 Electrical characteristics of LCD (VDD=2.8V, Ta=25 oC) Item
Symbol
IC power voltage Power input voltage
Conditions
MIN.
TYP.
MAX.
Unit
VDD
2.4
2.8
3.0
V
Vci
2.4
-
3.0
V
-20 oC
10.35
10.65
10.95
0 oC Sub LCD driving voltage VDD -V5
10.22
10.52
10.82
o
10.15
10.45
10.75
o
50 C
10.10
10.40
10.70
70 oC
10.02
10.32
10.62
25 C
V
High-level input voltage
VIHC
0.7VDD
Vcc
V
Low-level input voltage
VILC
-0.3
0.3Vcc
V
Consumption current of VDD
IDD
Consumption current of LED
ILED
Electric VR value ＝XXXXH VLED=9.8V
-
2.5
4
mA
-
15
20
mA
4-2 LED back light specification Item
Symbol
Conditions
MIN.
TYP.
MAX.
Unit
Forward voltage
Vf
If =15mA
-
9.8
10.8
V
Reverse voltage
Vr
-
-
12
V
Forward current
If
2-chip serial
12
15
20
mA
Power Consumption
PBL
If =15mA
-
147
-
mW
Uniformity (with L/G)
-
If=15mA
80% *1
-
-
Luminous color
White
Chip connection
2 chip serial connection
* Uniformity (LT):
Date : 2006/7/14
Min( P1 ~ P5) × 100 ≥ 80% Max( P1 ~ P5)
AMPIRE CO., LTD.
6
5
Optical Characteristics
Main LCD 5-1 Optical characteristics Driving codition:1/128 Duty LED backlight transmissive module: Item
Symbol
Response time
Temp. o
Min.
Std.
Max.
Tr
25 C
-
12.5
-
Tf
25 oC
-
12.5
-
Unit ms
Contrast ratio
CR
25 oC
TBD
TBD
-
-
Transmittance
T
25 oC
-
7
-
%
Visual angle range front and rear Visual angle range left and right Visual angle direction priority Brightness
Date : 2006/7/14
θ
θ
25 oC
(θf) 15 (θb) 35
25 oC
(θl) 45 (θr) 45
θ=0 o゜,φ=0 o (Note 2) θ=0 o, φ=0 o LED:ON, LIGHT:OFF (Note 4)
Degree
φ= 0o, CR≧10 LED:ON LIGHT:OFF (Note 3)
Degree
φ=90o, CR≧10 LED:ON LIGHT:OFF (Note 3)
12:00 150
Conditions
(Note 5) Cd/m2
AMPIRE CO., LTD.
VLED=9.8V, 15mA Full White pattern
7
5-2 CIE (x, y) chromaticity (1/128 Duty Ta = 25°C) Main LCD: (1/128 Duty Ta = 25°C) Transmissive Item
Symbol
Conditions Min.
Std.
Max.
x
0.563
0.603
0.643
y
0.304
0.344
0.384
x
0.281
0.321
0.361
y
0.497
0.537
0.577
x
0.098
0.138
0.178
y
0.121
0.161
0.201
x
0.275
0.315
0.355
y
0.306
0.346
0.386
Red
Green
Blue
White
θ=0゜,φ=0゜
θ=0゜,φ=0゜
θ=0゜,φ=0゜
θ=0゜,φ=0゜
Light source Value Item
Symbol
Conditions Min.
Std.
Max.
x
0.28
0.315
0.34
y
0.28
0.305
0.34
Light source
θ=0゜,φ=0゜ Unit: cd/m2
Main LCD 2300
-
brightness
(ILED=15mA)
Sub LCD
Unit: cd/m2 180
brightness
Date : 2006/7/14
(ILED=15mA)
AMPIRE CO., LTD.
8
Sub LCD 5-3 Optical characteristics Driving codition:1/64 Duty, 1/9 Bias LED backlight transflective module: Item
Symbol
Condition
Min.
Std.
Max.
Unit
Note
Response time
tr tf
25°C
-
200 200
-
ms ms
Note2
Contrast ratio
CR
T.B.D
7
-
θf
-
40
-
-
35
-
-
35
-
-
35
-
Visual angle range
θb θl
25°C, CR≥2
θr
Note4
Degree
Visual angle direction priority
-
-
12:00
Frame Frequency
fF
25°C
70
Hz
Brightness
-
60
Cd/m2
Date : 2006/7/14
VLED=9.8V, 15mA
AMPIRE CO., LTD.
Note3
Note5
9
NOTE 1: Optical characteristic measurement system Ring light
Brightness gauge BM-7 (Topcon)
LCD module
Metal halide lamp Glass fiber LED:OFF, LIGHT:ON Optical Detector
LCD
Brightness gauge BM-7 (Topcon) LED
LED:ON, LIGHT:OFF
NOTE 2: Response tome definition
Date : 2006/7/14
AMPIRE CO., LTD.
10
NOTE 3: φ、θ definition
NOTE 4: Contrast definition
NOTE 5 : Visual angle direction priority 12 : 00
9 : 00
8888
3 : 00
6 : 00
Date : 2006/7/14
AMPIRE CO., LTD.
11
6
Block Diagram
Block diagram (Main LCD) Display format: Color-TFT transmissive, 12 o’clock. Display mode: Normally white Display composition: 128 x RGB x 128 pixels LCD Driver : TL1771 Back light: White LED x 3 (ILED=15mA)
1.5" TFT LCD Panel 128(RGB)X128 pixels
TL1771 & Driving Circuit
LED Driver IC
VCC GND /RESET /CS RS /RD /WR D[0:15] V_PWR MLCD_BRGT GND
Date : 2006/7/14
AMPIRE CO., LTD.
12
Block diagram (Sub LCD) Display format: Display composition: LCD Driver : Back light:
FSTN, Transflective type, Positive, 6 o’clock. 96 x 64 dots S6B0724 White (Share Main LED backlight) 1
26
COM 63
COM31
S6B0724 COM32 SEG131 SEG95
S1
COM0 SEG0
S96
C1 C2
DOT 1
C33
96X64 DOTS LCD Panel
C32
C64
Block diagram (Whole Module)
Date : 2006/7/14
AMPIRE CO., LTD.
13
7
Part List
Main LCD No. BOM code (part No.) Name and Description
Maker
Q’ty
Location Mark
01
128128R
TFT-LCD
HannStar
1
02
TL1771
LCD Driver IC
Tomato
1
03
128128RFPC
Main-FPC
UniFlex
1
04
1100105058
Chip Resistor 100K(0402)
Ever co.
1
R1
05
1100105401
Chip Cap 1u/10V (0603)
Ever co.
5
C1,C2,C5,C10,C11
06
1200105301
Chip Cap 1u/6.3V (0402)
Ever co.
6
C3,C4,C6,C7,C8,C9
07
1200104402
0.1u/16V×4
Ever co.
1
CA1
No. BOM code (part No.) Name and Description
Maker
Q’ty
01
09664D
Monochromatic -LCD
Lin Yo
1
02
S6B0724
LCD Driver IC
Samsung
1
03
09664DFPC
Sub-FPC
Ever co.
1
No. BOM code (part No.) Name and Description
Maker
Q’ty
01
128128R-D1
PCB
APCP
1
02
1100221301
Chip Resistor 220R (0402)
Ever co.
1
R1
03
1100220301
Chip Resistor 22R (0402)
Ever co.
1
R8
04
1100470301
Chip Resistor 4.7k (0402)
Ever co.
2
R10,R21
05
1100105301
Chip Resistor 1M (0402)
Ever co.
1
R26
06
1100470301
Chip Resistor 47R (0402)
Ever co.
1
R28
07
1100000301
Chip Resistor 0R (0402)
Ever co.
2
R35,R36
08
1100123501
DNP
1
R42
09
1100240001
Chip Resistor 24R (0603)
Ever co.
1
R47
10
1100330001
Chip Resistor 33R (0603)
Ever co.
1
R43
11
1100101001
Chip Resistor100R (0402)
Ever co.
1
R2
1330100001
10uH
Panasonic
1330100007(substitute)
10uH
Murata
1
L4
13
1330100001
Chip Cap 1u/25V (0603)
Ever co.
2
C1,C5
14
1200106241
Chip Cap 10u/6.3V (0805)
Ever co.
3
C9,C29,C38
15
1200106242
Chip Cap 10u/6.3V 0.85t (0805)
Ever co.
2
C2,C39
16
1200471081
Chip Cap 470p/16V (0402)
Ever co.
2
C6,C7
17
1200105042
Chip Cap 1u/10V (0603)
Ever co.
7
C14,C40, ,C43,C33,C45,C46,C47
18
1200103305
Chip Cap 0.01u/10V (0402)
Ever co.
2
C8,C17
19
1200104171
Chip Cap 0.1u/16V (0402)
Ever co.
5
C11,C15, C30,C32,C34
20
1200475051
Chip Cap 4.7u/10V (0805)
Ever co.
1
C41
21
1200225401
Chip Cap 2.2u/6.3V (0603)
Ever co.
4
C12,C13,C42,C44
Sub LCD Location Mark
PCB
12
Date : 2006/7/14
AMPIRE CO., LTD.
Location Mark
14
22
1200225401
Chip Cap 2.2n/50V (0402)
Ever co.
2
C3,C4
23
1325510001
RB551V-30
promate
4
D8,D1,D9,D10
24
1320130001
UDZS13B/13V
promate
1
D11
25
1312301901
2SK3019
promate
3
Q1,Q2,Q3
26
1308121001
SM8121AH
NPC
1
U2
27
RT9361BPE
charge pump
Richtek
1
U3
28
RT9182EPES
Regulator
Richtek
1
U4
29
RT9193-28PB
Regulator
Richtek
1
U5
30
MV3018SOK-G
Back-End chip
Mtekvision
1
U6
31
RTSW2400MG
resonator
TDK
1
X3
32
ATCP-S354TW
Flash LED
Alti
1
LED1
33
1601258132
connector 34 Pin
ELCO
1
CN2
34
1601258962
connector 20 pin
ELCO
1
CN1
35
1340650051
Bead 600ohm (0402)
Siltron
2
L1,L2
36
1348405103
ESD-EMI filter
Amotech
5
VF2,VF3,VF4,VF5,VF6
37
1862754001
Rubber (14mm×1.8mm×2.0mm)
Jufo
2
38
1862754002
Rubber (6mm×2.0mm×16.0mm)
Jufo
2
BLU No. BOM code (part No.) Name and Description
Maker
Q’ty
01
3A25865701
Black Tape
3M
1
02
2A54132501
Diffuser
3M
1
03
3560404332
2-thin BEF
3M
1
04
3544330435
Light Guide
3M
1
05
8D34140221
Reflective
3M
1
06
3144145201
Housing
Tai Fa
1
07
5415131763
LED
Yuhsin
2
Q’ty
Location Mark
Tail FPC No.
BOM code (part No.)
Name and Description
Maker
01
1500121289
Tail FPC
UniFlex
1
02
1601258131
connector 34 Pin
ELCO
1
03
1651288132
connector 34 Pin
LG
1
Date : 2006/7/14
AMPIRE CO., LTD.
Location Mark
15
8 Interface Specifications Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
Terminal DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 MLCD_CS_N DIM C_RD LCM_BYPASS LIGHT_EN A2 SPK/REC+ SPK/RECINDUCTOR MLCD_BRGT MOTOR V_MSMP RESOUT_N GND LWR_N A1 DB6 DB5 DB4 DB3 DB2 DB1 DB0 GND VPWR
Date : 2006/7/14
Functions
Data Bus for 16-bits (high 8bit), 80-series MPU
Data Bus for 16-bits (low 8bit), 80-series MPU Chip select of main LCD (TL1771) LED B/L Dimming Control pin. Read pin of B/E IC LCM BYPASS mode pin Flash LED Enable Address pin of B/E IC Speaker (+) Speaker (-) Enable pin of flash LED driver circuit Power on Main & Sub Back Light simultaneously Vibrator terminal System Power For Main (VCC) & Sub LCD (VDD) Main & Sub LCD Reset terminal, active “L” GND-terminal for analog circuit Low_Byte Write clock terminal, active “L”. ( 80 series interface ) Command/data select input terminal. Data with “H,” and command with “L”
Data Bus for 16-bits (low 8bit), 80-series MPU
GND-terminal for analog circuit Battery power input for LED driver
AMPIRE CO., LTD.
16
9 80-system 16-bit interface 80-system 16-bit parallel data transmission is executed by setting IM2/1/0 pins to GND/Vcc/GND levels respectively. Data format for 16-bit interface
Data format for 16-bit interface
Date : 2006/7/14
AMPIRE CO., LTD.
17
10 Instruction Description Instruction List Driver IC: TL1771 Reg. No.
Register
IR
Index
W
SR
Status read
R/W RS
Upper Code
Lower Code
IB15 IB14 IB13 IB12 IB11 IB10 IB9
IB8
IB7
IB6
IB5
IB4
IB3
IB2
IB1
IB0
0
*
*
*
*
*
*
*
*
*
ID6
ID5
ID4
ID3
ID2
ID1
ID0
R
0
L7
L6
L5
L4
L3
L2
L1
L0
0
0
0
0
0
0
0
0
Oscillation Start
W
1
*
*
*
*
*
*
*
*
*
*
*
*
*
*
EXT OSC
Device code read
R
1
0
0
0
1
0
1
1
1
0
1
1
1
0
0
0
01h
Driver output control W
1
0
0
0
0
EPL SM
GS
SS
0
0
0
0
NL3 NL2 NL1 NL0
02h
LCD driving waveform control
W
1
0
0
0
0
0
0
F/L
0
0
0
0
0
0
03h
Entry mode
W
1
0
0
DIT BGR 0
0
0
0
0
0
07h
Display control 1
W
1
0
0
0
PT1 PT0 0
0
SPT 0
08h
Display control 2
W
1
0
0
0
0
FP3
FP2
FP1
FP0
0Bh
Frame cycle control
W
1
0
0
0
0
0
0Ch
External display interface control
W
1
0
0
0
0
0
R00h 1
0
0
0
I/D1 I/D0 AM
0
0
0
0
GON DTE CL
REV D1
0
0
0
0
BP3 BP2 BP1 BP0
0
DIV DIV 0 1 0
0
0
0
RTN RTN RTN RTN 3 2 1 0
0
0
0
DM1 DM0 0
04h 05h 06h D0
09h 0Ah
10h
Power control 1
W
1
0
0
11h
Power control 2
W
1
0
0
12h
Power control 3
W
1
0
0
13h
Power control 4
W
1
0
0
14h
Power control 5
W
1
0
0
RM
0
0
0
RIM
SAP SAP SAP BT2 BT1 BT0 DC2 DC1 DC0 AP2 AP1 AP0 SLP STB 2 1 0 VRN VRN VRN VRN VRN VRP VRP VRP VRP VRP 0 0 0 0 14 13 12 11 10 14 13 12 11 10 0
0
0
0
0
0
0
VC 0 0 0 0 0 0 MR VCO VDV VDV VDV VDV VDV 0 MG 4 3 2 1 0
0
0
0
0
0
0
0
0
VRH PON 3 VC VC M4 M3
VC2 VC1 VC0 VRH 2 VC M2
VRH 1 VC M1
VRH 0 VC M0
15h ~ 1Fh
: Setting disable
Date : 2006/7/14
AMPIRE CO., LTD.
18
Driver IC: TL1771 Upper Code
Lower Code
Reg. No.
Register
21h
RAM address register
W
1
AD15-8 (Upper)
AD7-0 (Lower)
RAM data write
W
1
Write Data (Upper)
Write Data (Lower)
RAM data read
R
1
Read Data (Upper)
Read Data (Lower)
30h
Gamma control (1)
W
1
0
0
0
0
31h
Gamma control (2)
W
1
0
0
0
0
32h
Gamma control (3)
W
1
0
0
0
0
33h
Gamma control (4)
W
1
0
0
0
0
34h
Gamma control (5)
0
1
0
0
0
0
35h
Gamma control (6)
0
1
0
0
0
0
36h
Gamma control (7)
0
1
0
0
0
0
37h
Gamma control (8)
0
1
0
0
0
0
38h
Power control 6
W
1
0
0
0
0
Gate scan position register
W
1
0
0
0
0
W
1
W
1
SE17 SE16 SE15 SE14 SE13 SE12 SE11 SE10 SS17 SS16 SS15 SS14 SS13 SS12 SS11 SS10
W
1
SE27 SE26 SE25 SE24 SE23 SE22 SE21 SE20 SS27 SS26 SS25 SS24 SS23 SS22 SS21 SS20
W
1
W
1
R/W RS
IB15 IB14 IB13 IB12 IB11 IB10 IB9
IB8
IB7
IB6
IB5
IB4
IB3
IB2
IB1
IB0
PKP 01 PKP 21 PKP 41 PRP 01 PKN 01 PKN 21 PKN 41 PRN 01 VRP 01
PKP 00 PKP 20 PKP 40 PRP 00 PKN 00 PKN 20 PKN 40 PRN 00 VRP 00
22h 23h ~ 2Fh PKP 12 PKP 0 32 PKP 0 52 PRP 0 12 PKN 0 12 PKN 0 32 PKN 0 52 PRN 0 12 VRN VRN 03 02
PKP 11 PKP 31 PKP 51 PRP1 1 PKN 11 PKN 31 PKN 51 PRN 11 VRN 01
PKP 10 PKP 30 PKP 50 PRP 10 PKN 10 PKN 30 PKN 50 PRN 10 VRN 00
0
0
0
0
PKP 02 PKP 0 22 PKP 0 42 PRP 0 02 PKN 0 02 PKN 0 22 PKN 0 42 PRN 0 02 VRP VRP 03 02
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SCN SCN SCN SCN SCN 4 3 2 1 0
39 ~ 3F 40 41 42 43 44 45
1’st screen driving position 2’nd screen driving position Horizontal window address Vertical window address
HEA 7 VEA 7
HEA 6 VEA 6
HEA 5 VEA 5
HEA 4 VEA 4
HEA 3 VEA 3
0
HEA 2 VEA 2
HEA 1 VEA 1
HEA 0 VEA 0
HSA 7 VSA 7
HSA 6 VSA 6
HSA 5 VSA 5
HSA 4 VSA 4
HSA 3 VSA 3
HSA 2 VSA 2
HSA 1 VSA 1
HSA 0 VSA 0
: Setting disable
Date : 2006/7/14
AMPIRE CO., LTD.
19
Reset Function If the /RESET input becomes L or the reset command is input, the internal timing generator is initialized. Must be reset after the power is supplied. The time required for the /RESET input is at least 1ms. When the power supply is reset while the power supply is ON, wait at least 10ms after the power has been supplied until the RC oscillation frequency become stabilized. While waiting, do not make initial settings for the instruction set, nor access to the GRAM. Register
Initial State of Instructions
Start oscillation
Executed
Driver output control
NL3-0=”110”, SS=”0”, CS=”0”, GS=”0”, SM=”0”, EPL=”0”,
LCD driving AC control
F/L=”0”
Power control 1
SAP2-0=”000”, BT2-0=”000”, DC2-0=”000”,AP2-0=”000” : LCD power off, STB=”0” : Standby mode off
Power control 2
VRN14-0=”00000”, VRP14-0=”00000”
Power control 6
VRN03-0=”0000”, VRP03-0=”0000”
Entry mode set
I/D1-0=”11” : Increment by 1, AM=”0” : Horizontal direction BGR=”0”
Display control 1
PT1-0=”00”, SPT=”0”, GON=”0”, TTD=”0”, CL=”0” : 65k-color mode REV=”0”, D1-0=”00” : Display off
Display control 2
FP3-0=”0101”, BP3-0=”0011”
Frame cycle control
DIV1-0=”00” : 1-divided clock TRB3-0=”0000” : 16-clock in 1H period
External display interface
RIM=”0” : 16-bit RGB interface DM1-0=”00” : operated by internal clock RM=”0” : system interface
Power control 3
VC2-0=”000”
Power control 4
VCRMR=”1”, PON=”0”, VRH3-0=”0000”
Power control 5
VCOMG=”0”, VDV4-0=”00000”, VCM4-0=”00000”
RAM address set
AD15-0=”0000h”
Gamma control
PKP02-00=”000”, PKP12-10=”000”, PKP22-20=”000”, PKP32-30=”000” PKP42-40=”000”, PKP52-50=”000”, PRP02-00=”000”, PRP12-10=”000” PKN02-00=”000”, PKN12-10=”000”, PKN22-20=”000”, PKN32-30=”000” PKN42-40=”000”, PKN52-50=”000”, PRN02-00=”000”, PRN12-10=”000”
Gate scan starting position SCN4-0=”00000”
Date : 2006/7/14
AMPIRE CO., LTD.
20
Register
Initial State of Instructions
1st screen division
SE17-10=”1001 1111”, SS17-10= ”0000 0000”
2nd screen division
SE27-20=”1001 1111”, SS27-20=”0000 0000”
Horizontal RAM address HEA7-0=”0111 1111”, HSA7-0=”0000 0000” position Vertical position
RAM
address
Date : 2006/7/14
VEA7-0=”1001 1111”, VSA7-0=”0000 0000”
AMPIRE CO., LTD.
21
11
Timing Characteristics
80-system Bus interface Timing Characteristics (Main LCD)
(Ta=25oC VCC = 2.2~2.4V)
IOVCC=1.7V to 2.0V, VCC=2.4 to 3.0V Item
Symbol
Min..
Typ.
Max.
Unit
Write
tCYCW
100
-
-
ns
Read
tCYCR
250
-
-
ns
Write low-level pulse width
PWLW
40
-
-
ns
Read low-level pulse width
PWLR
150
-
-
ns
Write high-level pulse width
PWHW
40
-
ns
Read high-level pulse width
PWHR
100
-
ns
tWRr, tWRf
-
-
25
ns
0
-
-
ns
10
-
-
ns
Bus cycle time
Write/Read rise/fall time Set up time (RS to CSB, WRB)
Write Read
tAS
Address hold time
tAH
2
-
-
ns
Write data set up time
tDSW
25
-
-
ns
Write data hold time
tH
5
-
-
ns
Read data delay time
tDDR
-
-
100
ns
Read data hold time
tDHR
5
-
-
ns
Date : 2006/7/14
AMPIRE CO., LTD.
22
80-system Bus interface Timing Characteristics (Sub LCD)
RS t A S 80
t A H 80 t C Y 80 tPW L
/R D , /W R CSB
0.9V D D
0.1V D D
tPW H t D S 80
t D H 80
D B 0 to D B 7 ( W rite ) t A C C 80
t O D 80
D B 0 to D B 7 ( R ead )
Read / Write Characteristics (80-series MPU) (VDD = 2.7V, Ta = -40 ~ +85°C) Item
Min.
Max.
tAS80
0
-
tAH80
0
-
System cycle time for write
tCY80
100
-
System cycle time for read
tCY80
166
Address setup time Address hold time
Signal RS
Symbol
Condition
Pulse width low
/WR
tPWL
40
-
Pulse width high
/RD
tPWH
40
-
tDS80
30
-
tDH80
5
-
15
-
10
50
Data setup time Data hold time Read access time Output disable time
DB0 to DB7
tACC80 tOD80
CL = 100 pF
Unit ns
ns
ns
ns
ns
NOTE: *1. The input signal rise time and fall time (tr, tf) is specified at 15 ns or less. (tr + tf) < (tCY80 - tPWLW - tPWHW ) for write, (tr + tf) < (tCY80 - tPWLR - tPWHR ) for read
Date : 2006/7/14
AMPIRE CO., LTD.
23
12 Setup of Power Supply The following show the sequence regarding power ON and OFF. Follow these sequence when executing display ON/OFF, standby set/off, sleep set/off.
Power supply ON/OFF sequence
Date : 2006/7/14
AMPIRE CO., LTD.
24
13 Instruction Setup Flow Display ON/OFF flow
[Display OFF]
[Display ON]
Display OFF GON="1", DTE=1 PT="10" D1-0="10"
Power Supply Setting
Wait (more then 2Frame)
Display ON PT="10" GON="1", DTE=1 D1-0="01"
Display OFF GON="1", DTE=1 PT="10" D1-0="00" Power Supply OFF SAP2-0="000" AP2-0="10" PON="0" GON="0", DTE="0"
CL=0
Wait (more then 2Frame) Display ON GON="1", DTE=1 D1-0="10" Wait (more then 2Frame)
Display OFF Display ON GON="1", DTE=1 D1-0="11"
Display OFF
Date : 2006/7/14
AMPIRE CO., LTD.
25
Standby, Sleep mode set/release
[Standby mode] Display Operation D="10"
[Sleep mode]
Standby Set
Display Operation D="10"
Standby set(STB="1")
Sleep set(SLP="1")
Continue more thean 5 frame
Continue more thean 5 frame
Standby release(STB="0")
Sleep release(SLP="0")
Wait more than 2 frame
Standby release
Wait more than 2 frame
D="11"
D="11"
Operation
Operation
Date : 2006/7/14
AMPIRE CO., LTD.
Sleep Set
Sleep release
26
14 Quality and Reliability 14.1
TEST CONDITIONS Tests should be conducted under the following conditions : Ambient temperature : 25 ± 5°C Humidity : 60 ± 25% RH.
14.2 SAMPLING PLAN Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan . 14.3 ACCEPTABLE QUALITY LEVEL A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation. 14.4
APPEARANCE An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits.
ZONE A active area ZONE B viewing area 14.5 NSPECTION QUALITY CRITERIA No. 1
2
Item Non display Irregular operation
3
Short
4
Open
Date : 2006/7/14
Criterion for defects
Defect type
No non display is allowed
Major
No irregular operation is allowed
Major
No short are allowed
Major
Any segments or common patterns that don’t activate are rejectable.
AMPIRE CO., LTD.
Major
27
Size D (mm) 5
D < 0.15
Black/White spot (I)
Ignore
0.15 < D < 0.20
3
0.20 < D < 0.30
2
0.30 < D
0
Length(mm) 6
Black/White line (I)
Acceptable number
Width (mm) 0.03 < W < 0.04
5
5.0 < L <10
0.04 < W < 0.06
3
1.0 < L < 5.0
0.06 < W < 0.07
2
L < 1.0
0.07 < W < 0.09
1
8
Black/White line (II)
5
0.50 < D < 1.20
3
1.20 < D
0
Back Light
10
Display pattern
Width (mm)
Minor
Acceptable number
20 < L
0.05 < W < 0.07
5
10 < L < 20
0.07 < W < 0.09
3
5.0 < L < 10
0.09 < W < 0.10
2
0.10 < W < 0.15
1
L < 5.0 9
Ignore
0.30 < D < 0.50
Length (mm)
Minor
Acceptable number
D < 0.30
Black/White sport (II)
Acceptable number
10 < L
Size D (mm) 7
Minor
1. No Lighting is rejectable 2. Flickering and abnormal lighting are rejectable
Minor
Major
Unit:mm Minor A+B ≤ 0.30 0 < C 2 Note:
D+E F+G ≤ 0.25 ≤ 0.25 2 2
1. Acceptable up to 3 damages 2. NG if there’re to two or more pinholes per dot
Date : 2006/7/14
AMPIRE CO., LTD.
28
Blemish & Foreign matters
11
Size: D=
A+ B 2
Size D (mm)
Polarizer
12
Ignore
D < 0.15 0.15 < D < 0.20
3
0.20 < D < 0.30
2
0.30 < D
0
Width (mm) Scratch on
Acceptable number
Minor
Length (mm)
Acceptable number
Ignore
Ignore
L < 2.0
Ignore
L > 2.0
1
L > 1.0
1
L < 1.0
Ignore
Note (1)
Note(1)
W<0.03 0.03
