Transcript
M instructions:Metal instruc
18/3/08
1:57 PM
Page 1
METAL CASE AUTOMATIC HAND DRYER MODEL AMTHD240M
The Airmate Automatic Hand Dryer HD240M is fully automatic and features solid-state infra-red control that automatically switches the unit on & off when hands are passed under the air outlet. It is an ideal choice for hotels, restaurants, large office buildings or public amenities etc.The Airmate hand dryer has rapid drying times which are achieved through the high velocity airflow and high wattage element. The hand dryer has a vandal resistant streamlined metal case and provides increased durability in high usage public access installations. Other features include: • Protection provided by a safety cut-out switch which monitors any objects accidentally placed beneath the unit. The hand dryer will automatically switch-off after continuously running for approximately 50 - 60 seconds and will not run again until any offending object is removed. • A directional rotating air outlet which allows 360 degree movement for multiple drying angles.
M instructions:Metal instruc
18/3/08
1:57 PM
Page 2
INSTALLATION CHECKLIST • Before installation, check to see that the cord & plug top has not been damaged through any rough treatment or during transport. • Ensure the mounting area is clear of any swinging doors or other features likely to cause damage to the unit. • The unit should be mounted in accordance with all building and electrical regulations. • Mount at least 220mm above bench tops, shelves or cupboards and 600mm or greater from any taps or sinks as per building & electrical regulations. • It is recommended that the electrical supply to this unit is protected by an RCD (safety switch).
MOUNTING INSTRUCTIONS
198mm
IMPORTANT - THIS APPLIANCE MUST BE EARTHED AND SHOULD ONLY BE INSTALLED BY A QUALIFIED ELECTRICIAN. 1. Remove the metal cover by unscrewing the 2 hex key bolts with the 5mm Allen key (12) supplied with the unit (Drawing 2 below). 2. Once the bolts are undone, tilt the cover outwards from the bottom, detaching from the base plate by lifting the cover upwards. Disconnect both the earth (13) and infra red sensor cables (11) (Drawing 2 below). 3. Fix the base plate to the wall with the 4 screws & anchors supplied or use 5mm masonry bolts. (For Mounting holes and template, Referto (Drawing 1 below) 4. Once base plate is mounted, re-connect the 2 cables at the points shown and re-fit the case to the base plate in order of the arrows numbered ( 1 2 3 4 ) in (Drawing 2 below). Ensure cover is fitted correctly and sitting flat against the base plate before tightening the 2 hex key bolts. To ensure cover is locked down, test by pulling forward gently on the unit. 5. The sensor is factory set and will detect any hand movement within the range of 0-11cm’s below the hand dryer. The hand dryer will stop automatically when the hand is removed
Drawing 1
Drawing 2
M instructions:Metal instruc
18/3/08
1:57 PM
Page 3
RECOMMENDED INSTALLATION HEIGHTS FROM FLOOR TO UNDERSIDE MOUNTING HOLES OF HAND DRYER ARE AS FOLLOWS: Men’s washroom Women’s washroom Childs 13-17 yrs washroom Childs 10-13 yrs washroom Childs 7-10 yrs washroom Childs 4-7 yrs washroom Disabled person’s washroom
1065mm 1015mm 1015mm 915mm 865mm 760mm 800mm
IMPORTANT NOTICES: IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY AN AUTHORISED ELECTRICIAN OR SERVICE AGENT • This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure they can use the appliance safely. • Children should be supervised to ensure that they do not play with the appliance. • Before conducting any maintenance or internal cleaning, ensure that the power supply has been isolated / disconnected from the unit.
SERVICE & MAINTENANCE • To ensure optimum performance and maximum life from this hand dryer, the unit should be serviced on a regular basis by qualified personnel. • Servicing should be conducted every 6 months with heavy (high traffic) use & every 12 months with regular to light use. • Servicing should include cleaning the fan blades internally and removing all accumulated lint and dirt. • DO NOT CLEAN WHILE POWER IS TURNED ON • Only use non-abrasive liquid cleaners to clean the surface of the case if necessary, taking care not to wet any electrical components FAILURE TO SERVICE AND MAINTAIN THE HAND DRYER APPROPRIATELY WILL VOID THE WARRANTY
SPECIFICATIONS: Electrical Supply: Power Consumption: Waterproof rating: Air movement Electrical Lead: Weight: Measurements:
240V 50Hz 2400W – 10 Amps IPX1 Air Speed 30 m/s Air Volume 270 M3/h 3 Pin 10A lead, 0.8 metre in length 5 Kg 235mm H x 265mm W x 200mm D
Tested & approved to meet Australian & EMC Standards. AS/NZS 60335.2.23 & AS/NZS CISPR 14
M instructions:Metal instruc
18/3/08
1:57 PM
Contact 1300 651 066
Page 4
protick.com.au
