Transcript
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
4
3
2 ZONE
FOR SINGLE UNIT 4 INSTALLATION SEE ASSEMBLY STEP 3.0
D
FRONT BRACKET
T2100 UNITS SHOWN FOR REFERENCE ONLY
1 REV A B C D
REVISION DESCRIPTION PRODUCTION RELEASE PER ECN 20090752 REVISED PER ECN 20100611 REVISE PER ECN CP110119 REVISED PER CP130166
DATE APPROVED 07/20/09 G. Trader 05/14/10 G. Trader 02/15/11 G. Trader 01/23/13 F. AMORINO D
2 8
SEE ASSEMBLY STEP 2.0
2X
SEE ASSEMBLY STEP 8.0 C
C
3
5 FRONT PANEL
4X
1 SEE ASSEMBLY STEP 2.0 SEE ASSEMBLY STEP 3.0
SEE ASSEMBLY STEP 5.0 B
B
7
Parts List 6
SEE ASSEMBLY STEP 5.0
4X
SEE ASSEMBLY STEP 4.0 5
8X
SEE ASSEMBLY STEP 2.0 SEE ASSEMBLY STEP 3.0
A
REAR BRACKET SEE ASSEMBLY STEP 2.0 SEE ASSEMBLY STEP 3.0
NOTES: 1.0 REMOVE THE RUBBER BEZELS FROM THE FRONT AND REAR OF THE SYNTHESIZER UNIT(S). 1.1 FOR HMC-T2100B AND HMC-T2200 SERIES UNITS, REMOVE THE HANDLE ASSY AND HANDLE RACHETS, AND REMOVE THE HANDLE SPACERS FROM THE ENCLOSURE COVERS PRIOR TO PROCEEDING TO THE NEXT STEP. 2.0 FOR A TWO UNIT ASSEMBLY, INSTALL THE FRONT BRACKET (ITEM 2) AND REAR BRACKET (ITEM 3) ONTO THE TWO SYNTHESIZER UNITS USING 12 FLAT HEAD SCREWS (ITEM 5). THE FLANGES ON THE REAR BRACKET SHOULD POINT UP (AS SHOWN). 3.0 FOR A ONE UNIT ASSEMBLY, INSTALL THE FRONT BRACKET (ITEM 2), A BLANK PANEL (ITEM 4), AND THE REAR BRACKET (ITEM 3) ONTO A SYNTHESIZER UNIT USING 10 FLAT HEAD SCREWS (ITEM 5). THE FLANGES ON THE REAR BRACKET SHOULD POINT UP (AS SHOWN). 4.0 TORQUE SCREWS PER HITTITE DOCUMENT 117337. 5.0 ASSEMBLE UNIT(S)/BRACKET TO FRONT PANEL (ITEM 1), USING 4 HEX NUTS (ITEM 6). 6.0 INSTALL PAN HEAD SCREW (ITEM 7) TO FRONT PANEL AND FRONT BRACKET. TORQUE AS REQUIRED. 7.0 TO INSTALL THE ABOVE SUB-ASSEMBLY INTO A RACK, FIRST INSTALL A SET OF THE APPROPRIATE RIGHT ANGLE SIDE RAILS (PER RACK VENDOR RECOMMENDATION). 8.0 PLACE THE POWER SUPPLY(S) ONTO THE SIDE RAIL(S) (TO THE REAR OF THE UNITS), AND SECURE THEM TO THE SIDE RAILS WITH HOOK AND LOOP STRAP(S) (ITEM 8). 9.0 INSTALL THE PANEL/BRACKET/UNIT SUB-ASSEMBLY INTO THE RACK AND SECURE WITH RACK SCREWS.
3
QTY
DESCRIPTION
1
1
Panel, Front, Rack Mount Kit
2
1
Bracket, Mounting, Rack Mount Kit
3
1
Bracket, Rear, Rack Mount Kit
4
1
Panel, Blank, Rack Mount Kit
5
12
6
4
Nut, Nylon Insert, #6-32
7
1
Screw, Pan Hd, 4-40 X .250 LG
8
2
Strap, Hook-n-Loop, 18 inch
Screw, Flat Hd 82, 4-40 x .312 LG
PROPRIETARY TO HITTITE MICROWAVE CORPORATION UNLESS OTHERWISE SPECIFIED:
DRAWN BY
G. Trader DIMENSIONS ARE IN INCHES [mm] CHECKED BY DRAWING PRACTICES PER ASME Y14.100 ENGINEER INTERPRET DIMENSIONS & TOLERANCES PER ASME Y14.5-2009 TOLERANCES:
NEXT ASSY
4
ITEM
USED ON
2
.XX .XXX .XXXX ANGLES
.01 .005 .0020 .5 DEG.
DATE DRN
HITTITE MICROWAVE CORPORATION
5/18/2009
20 Alpha Road Chelmsford, MA 01824 TITLE
A
Dual Rack Mount Kit, HMC-RM02
THIRD ANGLE PROJECTION
SIZE
DO NOT SCALE DRAWING
SCALE
CODE ID NO.
DWG NO.
C 1CN88
D
126991 WT
1
REV
SHEET
1
OF 2
4
3
2 ZONE
1 REVISION DESCRIPTION SEE SHEET 1 OF 2
REV -
DATE -
APPROVED -
STEP 1: PRESS BUTTON ON EACH SIDE OF HANDLE AND ROTATE TO THE POSITION SHOWN UNTIL IT LOCKS
D
D
STEP 2: HOLD IN THE BUTTONS AND ROTATE THE HANDLE TOWARDS THE FRONT OF THE SYNTHESIZER SLIGHTLY WHILE PULLING THE BASE OF THE HANDLE OUTWARD UNTIL THEY START TO SEPARATE FROM THE HOUSING. THE HANDLE IS MEANT TO BEND TO CLEAR THE MOUNT. THERE WILL BE NO DAMAGE TO THE HANDLE BY DOING THIS OPERATION.
C
C
B
B
STEP 3: REMOVE THE 2 SCREWS ON EACH SIDE THAT HOLD THE HANDLE MOUNT AND SPACER
PROPRIETARY TO HITTITE MICROWAVE CORPORATION UNLESS OTHERWISE SPECIFIED:
G. Trader DIMENSIONS ARE IN INCHES [mm] CHECKED BY DRAWING PRACTICES PER ASME Y14.100 ENGINEER INTERPRET DIMENSIONS & TOLERANCES PER ASME Y14.5-2009
A FOR ASSEMBLING HANDLE BACK ON TO SYNTHESIZER, REVERSE THESE STEPS. NOT THE ORIENTATION OF THE HANDLE MOUNT.
TOLERANCES:
NEXT ASSY
4
3
DRAWN BY
USED ON
2
.XX .XXX .XXXX ANGLES
.01 .005 .0020 .5 DEG.
DATE DRN
HITTITE MICROWAVE CORPORATION
5/18/2009
20 Alpha Road Chelmsford, MA 01824 TITLE
A
Dual Rack Mount Kit, HMC-RM02
THIRD ANGLE PROJECTION
SIZE
DO NOT SCALE DRAWING
SCALE
CODE ID NO.
DWG NO.
C 1CN88
D
126991 WT
1
REV
SHEET
2
OF 2
