Preview only show first 10 pages with watermark. For full document please download

Analog I/o Slave Digital I/o Slave Pulse I/o Slave Temperature

   EMBED


Share

Transcript

Slave Module TPM provides 6 categories of slaves including Digital I/O, Analog I/O, Motion control, Temperature input, Pulse input and Hub/Gateway. For Digital I/O, there are 3 main types, first is 16 channel for 8In8Out, second is 32 channel for 16In/16Out, 32In, 32Out, and the last is 64 channel for 32In32Out/64In/64Out/48In16Out/16In48Out. With these slaves you can connect your actuators/sensors directly and easily. For Analog I/O, there are 3 types including 8 Ch. AI, 4 Ch. AO and 8AI/4AO. For Motion control, there are 2 main types, one is for 1-axis control and the other is for 4-axis control. For Temperature input, K/J/E/T types of thermocouple sensors can be connected directly. For Pulse input, single phase pulse ranging from 5~24V can be connected directly. Digital I/O Slave 106-D5xx 106-D4xx EZM-D1xx 107-D1xx 107-D2xx Analog I/O Slave 108-A122 106-A180 P ulse I/O Slave T emperature Slave 108-T140 Motionnet ® 108-C144 108-P144 Rs-485 Gateway hub 108-H104 Motion 1-axis Slave 102-M1x1 Series 24 106-A104 Taiwan Pulse Motion Co.,Ltd 108-G180 Motion 4-axis Slave STP-M111A/B/G/H 106-M304T Motionnet Digital Slave DIO Selection Guide 32-Channel Digital I/O Dlave Model 106-D440-NXT 106-D422-NNT 106-D404-XNT 106-D240-NXT 106-D222-NNT 106-D204-XNT Channel 32 In 16 In / 16 Out 32 Out 32 In 16 In / 16 Out 32 Out Screw Terminal Block Connector Alternative Box Header 32-Channel Digital I/O Dlave Model 107-D140-NXT 107-D122-NNT 107D104-XNT 107-D240-NXT 107-D222-NNT 107-D204-XNT Channel 32 In 16 In / 16 Out 32 Out 32 In 16 In / 16 Out 32 Out Pluggable Terminal Block Connector 16-Channel Digital I/O Dlave Alternative Box Header 64/96-Channel Digital I/O Dlave Model 106-D520-NXT 106-D511-NNT 106-D502-XNT Model 107-D340-NXT 107-D322-NNT 107D304-XNT Channel 16 In 8 In / 8 Out 16 Out Channel 64 In 32 In / 32 Out 64 Out Model 107-D542-NXT 107-D533-NNT 107-D524-XNT Channel 64 In / 32 Out 48 In / 48 Out 32 In / 64 Out Connector Pluggable Terminal Block Connector Pluggable Terminal Block Taiwan Pulse Motion Co.,Ltd 25 Digital I/O Slave 106-D5xx Series 16 Ch. DI/O Slave Module Ordering information 106-D520-NXT 16 Ch. Digital input with NPN type 106-D511-NNT 8 Ch. Digital input/output with NPN type 106-D502-XNT 16 Ch. Digital output with NPN type SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length I/O connector 106-D511-NN Terminal Definitions Dimension Diagram Features DIN rail mounting (L-75 x W-69 x H-41 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic Pluggable terminal block with spring plug connectors Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Input impedance 5.6KΩ/0.5W Input current ±5mA(Max) Output types NPN open collector darlington transistors Switch capacity Each output Ch. is 350mA at 24V DC Response time On to Off, about 47.6µs; Off to On, about 7.8µs Over current protection 3A (max) for each port (8 Ch.) General 26 Taiwan Pulse Motion Co.,Ltd Power supply +18V DC to +30V DC Power consumption 1.5W typical Power supply Working temperature +18V 0 to 60℃ DC to +30V DC Motionnet Digital Slave Digital I/O Slave 106-D4xx Series 106-D2xx Series 32 Ch. DI/O Slave Module Ordering information 106-D404-XNT 32 Ch. Digital output with NPN type 106-D422-NNT 16 Ch. Digital input/output with NPN type 106-D440-NXT 32 Ch. Digital input with NPN type 106-D204-XNT 32 Ch. Digital output with NPN type 106-D222-NNT 16 Ch. Digital input/output with NPN type 106-D240-NXT 32 Ch. Digital input with NPN type SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Dimension Diagram Features DIN rail mounting (L-75 x W-124 x H-41 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Input impedance 5.6KΩ/0.5W Input current ±5mA(Max) Output types NPN open collector darlington transistors Switch capacity Each output Ch. is 350mA at 24V DC Response time On to Off, about 47.6µs; Off to On, about 7.8µs Over current protection 3A (max) for each port (8 Ch.) General Power supply +18V DC to +30V DC Power consumption 1.5W typical Working temperature 0 to 60℃ Taiwan Pulse Motion Co.,Ltd 27 Digital I/O Slave EZM-D1xx Series EZM-D140-NXT EZM-D122-NNT EZM-D104-XNT 32 Ch. DI/O Slave Module Features Customize PCB mounting (L-98 x W-26 x H-77 mm) Max. 20Mbps transfer rate LED diagnostic Ordering information EZM-D140-NXT 32 Ch. Digital input with NPN type EZM-D122-NNT 16 Ch. Digital input/output with NPN type EZM-D104-XNT 32 Ch. Digital output with NPN type Dimension Diagram Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Input impedance 5.6KΩ/0.5W Input current ±5mA(Max) Output types NPN open collector darlington transistors Switch capacity Each output Ch. is 350mA at 24V DC Response time On to Off, about 47.6µs; Off to On, about 7.8µs Over current protection 3A (max) for each port (8 Ch.) General 28 Taiwan Pulse Motion Co.,Ltd Power supply +18V DC to +30V DC Power consumption 3W typical Working temperature 0 to 60℃ Motionnet Digital Slave Digital I/O Slave EZM-D2xx Series EZM-D242 EZM-D222 64 / 96 Ch. DI/O Slave Module with Ordering information EZM-D260 96 Ch. Digital input EZM-D242 64 Ch. / 32 Ch. Digital input / output EZM-D233 48 Ch. / 48 Ch. Digital input / output EZM-D224 32 Ch. / 64 Ch. Digital input / output EZM-D206 96 Ch. Digital output EZM-D240 64 Ch. Digital input EZM-D222 32 Ch. / 32 Ch. Digital input /output EZM-D204 64 Ch. Digital output Dimension Diagram Features Customize PCB mounting (L-98 x W-25 x H-49 mm) Max. 20Mbps transfer rate Flexible I/O interface deployment Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps Status LED Power, Error and Run Switch Baudrate and Address General Power supply +5V at 300mA Working temperature 0 to 60℃ Taiwan Pulse Motion Co.,Ltd 29 Digital I/O Slave 107-D1xx Series 107-D122-NNT 107-D140-NXT 107-D104-XNT 32 Ch. DI/O Slave Module with Pluggable Terminal Features DIN rail mounting (L-122 x W-65 x H-104 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic Pluggable terminal block with spring plug connectors Ordering information 107-D140-NXT 32 Ch. Digital input with NPN type 107-D122-NNT 16 Ch. Digital input & output with NPN type 107-D104-XNT 32 Ch Digital output with NPN type SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Dimension Diagram Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Input impedance 5.6KΩ/0.5W Input current ±5mA(Max) Output types NPN open collector darlington transistors Switch capacity Each output Ch. is 350mA at 24V DC Response time On to Off, about 47.6µs; Off to On, about 7.8µs Over current protection 3A (max) for each port (8 Ch.) General 30 Taiwan Pulse Motion Co.,Ltd Power supply +18V DC to +30V DC Power consumption 3W typical Working temperature 0 to 60℃ Motionnet Digital Slave Digital I/O Slave 107-D1xx Series 64 Ch. DI/O Slave Module with Pluggable Terminal Ordering information 107-D180-NXT 64 Ch. Digital input with NPN type 107-D108-XNT 64 Ch. Digital output with NPN type 107-D144-NNT 32 Ch. /32 Ch. Digital input/output with NPN type 107-D162-NNT 48 Ch. /16 Ch. Digital input/output with NPN type 107-D126-NNT 16 Ch. /48 Ch. Digital input/output with NPN type SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Dimension Diagram Features DIN rail mounting (L-122 x W-122 x H-104 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic Pluggable terminal block with spring plug connectors Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Input impedance 5.6KΩ/0.5W Input current ±5mA(Max) Output types NPN open collector darlington transistors Switch capacity Each output Ch. is 350mA at 24V DC Response time On to Off, about 47.6µs; Off to On, about 7.8µs Over current protection 3A (max) for each port (8 Ch.) General Power supply +18V DC to +30V DC Power consumption 3W typical Working temperature 0 to 60℃ Taiwan Pulse Motion Co.,Ltd 31 Digital I/O Slave 107-D3xx Series 64 Ch. DI/O Slave Module with Pluggable Terminal Ordering information 107-D322-NN 32 Ch. /32 Ch. Digital input /output with NPN type 107-D331-NN 48 Ch. /16 Ch. Digital input /output with NPN type 107-D340-NX 64 Ch. Digital input with NPN type 107-D304-XN 64 Ch. Digital output with NPN type 107-D313-NN 16 Ch. /48 Ch. Digital input /output with NPN type SCB-166-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Dimension Diagram Features DIN rail mounting (L-122 x W-102 x H-77 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic Pluggable terminal block with spring plug connectors Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Input impedance 5.6KΩ/0.5W Output types NPN open collector darlington transistors Switch capacity Each output Ch. is 350mA at 24V DC Response time On to Off, about 47.6µs; Off to On, about 7.8µs General 32 Taiwan Pulse Motion Co.,Ltd Power supply +18V DC to +30V DC Power consumption 5W typical Working temperature 0 to 60℃ Motionnet Digital Slave Digital I/O Slave 107-D5xx Series 96 Ch. DI/O Slave Module with Pluggable Terminal Ordering information 107-D542-NN 64 Ch. /32 Ch. Digital input /output with NPN type 107-D551-NN 80 Ch. /16 Ch. Digital input /output with NPN type 107-D533-NN 48 Ch. /48 Ch. Digital input /output with NPN type 107-D524-NN 32 Ch. /64 Ch. Digital input /output with NPN type 107-D515-NN 16 Ch. /80 Ch. Digital input /output with NPN type 107-D506-XN 96 Ch. Digital output with NPN type 107-D560-NX 96 Ch. Digital input with NPN type SCB-166-06A/10A/20A/30A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Dimension Diagram Features DIN rail mounting (L-122 x W-125 x H-77 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic Pluggable terminal block with spring plug connectors Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Input impedance 5.6KΩ/0.5W Input current ±5mA(Max) Output types NPN open collector darlington transistors Switch capacity Each output Ch. is 350mA at 24V DC Response time On to Off, about 47.6µs; Off to On, about 7.8µs Over current protection 3A (max) for each port (8 Ch.) General Power supply +18V DC to +30V DC Power consumption 6W typical Working temperature 0 to 60℃ Taiwan Pulse Motion Co.,Ltd 33 Analog I/O Slave 108-A122 8 Ch. Analog input and 4-Ch. Analog output Slave Module Features DIN rail mounting (L-75 x W-124 x H-34 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic 8 Ch. analog input and 4 Ch. analog output Ordering information 108-A122 8 Ch. analog input (+10V, ±5.12V, ±2.56V, ±1.28V,±640mV,±320mV,±160mV,±80mV) and 4 Ch. analog output (+10V) Signal Wiring Diagram Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms AD/DA Control Analog Inout Signals Terminal Assignment Terminal Definitions Dimension Diagram Effective resolution 12-bit Input impedance 20MΩ Input range Standard ±10V, ±5.12V, ±2.56V, ±1.28V, ±640mV, ±320mV, ±160mV, ±80mV, Output impedance 0.3Ω Output range ±10V Sample rate 8ms/8 ch. Fault and over-voltage protection Up to ±12V Accuracy ±2LBS(INL) / ±0.2LBS(DNL) Zero Drift(ADC) ±0.2uV/℃ Span Drift(ADC) ±0.5ppm/℃ Zero Drift(DAC) -0.5ppm/℃ (25℃ ~125℃ ) Span Drift(DAC) -3ppm/℃ General 34 Taiwan Pulse Motion Co.,Ltd Power supply +24V DC±10% Power consumption 3W typical Working temperature 0 to 60℃ Motionnet Analog Slave Analog I/O Slave 106-A180-01 8 Ch. AI Slave Module Ordering information 106-A180-01 8-Ch. analog input(±10V,±5V,±2.5V, ±1.25V) SCB-166-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Signal Wiring Diagram Features DIN rail mounting (L-75 x W-124 x H-32 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic 8 Ch. analog input Specification ® Motionnet Analog Inout Signals Terminal Assignment Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms ADC Control Terminal Definitions (CN4,CN5) Dimension Diagram Effective resolution 16-bit Input impedance 20MΩ Input range Standard ±10V, ±5V, ±2.5V, ±1.25V (106-A180-01) Sample rate Programmable, 1/(1~255)ms; samples/sec. Fault and over-voltage protection Up to ±25V Accuracy 0.1% or better Zero Drift ±3uV/℃ Span Drift 25ppm/℃ CMR@50/60Hz 92dB General Power supply +24V DC±10% Power consumption 1.5W typical Working temperature 0 to 60℃ Taiwan Pulse Motion Co.,Ltd 35 Analog I/O Slave 106-A104 4 Ch. AO Slave Module Ordering information 106-A104-01 4 Ch. analog output (±10V) SCB-166-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Terminal Assignment Features DIN rail mounting (L-75 x W-124 x H-34 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic 4 Ch. analog output Specification ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms DAC Control Terminal Definitions (CN4) Dimension Diagram Effective resolution 16-bit Output impedance 0.3Ω Output range ±10V Accuracy ±4LBS(INL)/±1LBS(DNL) Short-circuit protection current 6mA Zero Drift ±2ppm/℃ Span Drift 25ppm/℃ General 36 Taiwan Pulse Motion Co.,Ltd Power supply +24V DC±10% Power consumption 3W typical Working temperature 0 to 60℃ Motionnet Analog Slave Temperature Slave 108-T140 8 Ch. Temperature Slave Module for Thermocouple Features Specification DIN rail mounting (L-75 x W-124 x H-32 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic 8 Ch. analog input Ordering information 108-T140 8 Ch. temperature slave module for thermocouple SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Signal Wiring Diagram Analog Inout Signals ® Motionnet Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps ADC Control Input Ch. 8 Ch. differential Input type 4 ~ 20 mA with switchable resister. (No need external resister) Thermocouple type: E, J, K, T. Effective resolution 16-bit Input impedance 20MΩ. Sample rate Low speed: 5Hz/8ch High speed: 50Hz/8ch Fault And over-voltage protection Up to ±12V Accuracy 0.1% or better Photo- isolation 3750Vrms Intra-module isolation, field to logic 3000V DC CMR@50/60Hz 110dB General Terminal Assignment Power supply +18V DC to +30V DC Power consumption 3W typical Working temperature 0 to 60℃ Thermocouple type Terminal Definitions (CN4,CN5) Type Range ℃ Type Range ℃ E -100℃ ~ +700℃ K -200℃ ~ +900℃ J -100℃ ~ +600℃ T -100℃ ~ +350℃ Taiwan Pulse Motion Co.,Ltd 37 Pulse I/O Slave 108-C144 4 Ch. Encoder Slave Module Ordering information 108-C144 4 Ch. encoder input module SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Signal Wiring Diagram Features DIN rail mounting (L-75 x W-124 x H-34 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic 4 Ch. encoder input Position compare and trigger output Compare output FIFO x 2 Specification ® Motionnet I/O Connector Terminal Definitions Dimension Diagram Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Encoder Ch. 4 Ch. independent 32-bit encoder Input type Isolated Isolated input voltage Logic level 0: 1V max. Logic level 1: 5V or 24V Incremental encoder ±EA x 4, ±EB x 4 Alarm output Alarm on counter 0 ~ 3 Position compare output CMP x 2 CMP FIFO 1024 Points / ch General 38 Taiwan Pulse Motion Co.,Ltd Power supply +18V DC to +30V DC Power consumption 1.5W typical Working temperature 0 to 60℃ Motionnet Pulse Slave Pulse I/O Slave 108-P144 4 Ch. Pulse Counter Slave Module Ordering information 108-P144 4 Ch. pulse input module SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Signal Wiring Diagram Features DIN rail mounting (L-75 x W-124 x H-34 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic 4 Ch. Up/down 32 bit counter Programmable Input Filter Specification ® Motionnet I/O Connector Terminal Definitions Dimension Diagram Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Counter Ch. 4 Ch. independent 32-bit counter Input type Isolated Isolated input voltage Logic level 0: 1V max. Logic level 1: 5V or 24V Alarm output Alarm on counter 0 ~ 3 Input frequency 5Hz ~ 5MHz Function mode Counter, Frequency, Period Input filter 1µs ~ 65535µs Output type Open collector General Power supply +18V DC to +30V DC Power consumption 1.5W typical Working temperature 0 to 60℃ Taiwan Pulse Motion Co.,Ltd 39 Motionnet® Hub 108-H104 Motionnet® Hub Ordering information 108-H104 Motionnet® HUB SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Features DIN rail mounting (L-75 x W-69 x H-31 mm) Max. 20Mbps transfer rate Easy installation with RJ45 phone jack and LED diagnostic Cascade connection Specification ® Motionnet Dimension Diagram Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps I/O isolation voltage 2.5KVrms Number of hub cascade Max. 3 layers Transfer delay time 900ns for up transfer and 900ns for down transfer(1800ns for both up and down) Serial communication protocol Motionnet® proprietary protocol General 40 Taiwan Pulse Motion Co.,Ltd Power supply +18V DC to +30V DC Power consumption 1.5W typical Working temperature 0 to 60℃ Motionnet Hub Slave RS-485 Gateway 108-G180 RS-485 Gateway Ordering information 108-G180 Motionnet® – RS-485 gateway SCB-1BB-06A/10A/20A/30A/50A CAT5 UTP/STP LAN cable, 0.6m/1m/2m/3m/ 5m length Features DIN rail mounting (L-75 x W-124 x H-31 mm) Max. 20Mbps transfer rate DCON transfer to Motionnet® Easy installation with RJ45 phone jack and LED diagnostic Application topology Specification ® Motionnet Dimension Diagram Serial interface Half duplex RS-485 with transformer isolation Cable type CAT5 UTP/STP Ethernet cable Surge protection 10KV Transmission speed 2.5Mbps, 5Mbps, 10Mbps and 20Mbps Number of DCON modules Max. 16 modules Baud rate of DCON modules 1200bps ~ 115200bps Number of gateway modules Max. 64 Transfer data rate 0.4ms/20Mbps General Power supply +18V DC to +30V DC Power consumption 1.5W typical Working temperature 0 to 60℃ Taiwan Pulse Motion Co.,Ltd 41