Transcript
Installation Guide Smart-UPS™On-Line SRT 2-Post Rack-Mount Rail Kit Package Contents Inspect the contents upon receipt. Notify the carrier and dealer if the unit is damaged. All Models • 2 pairs of rails • 24 pan head screws
x24
SRT1000/SRT1500 and SRT2200/SRT3000, 2U models SRT5K, 3U models and SRT external battery packs
x6
x4
x8
x4
SRT6K, 4U models
SRT8K/SRT10K, 6U models
x8
x8
x4
x4
Install Rails to 2-Post Rack Pem nuts are provided on single side of two rails. Install these rails such that the pem nut is towards the front of the 2-post rack.
x6
x6
x6
x6
suo1020a
2
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
SRT1000/SRT1500/SRT2200/SRT3000 UPS Note: UPS and External Battery Pack (XLBP) models may differ in appearance from those depicted in these graphics. The installation process is identical for all models.
CAUTION DAMAGE TO EQUIPMENT OR PERSONNEL • The equipment is heavy. Each APCRBC152 battery module weighs 16.4 kg (36.2 lbs) and each APCRBC141 battery module weighs 12.5 kg (27.6 lb). Each APCRBC155 battery module weighs 11 kg (24.25 lb). • Always practice safe lifting techniques adequate for the weight of the equipment. • Remove the battery modules before installing the UPS. • Use the battery module handle to carefully slide the battery module in or out of the unit. • Do not use the battery module handle to lift or carry the battery module. • Place the UPS on a table to remove the stabilizer brackets. • Always install the UPS at the bottom of the rack. • Always install the XLBP below the UPS in the rack. Failure to follow these instructions can result in equipment damage and minor or moderate injury.
Tower to rack-mount conversion
suo0875b
suo0874b
suo0873b
suo0872b
x3
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
3
suo08
su 08
45 b
71b
Install the SRT1000/SRT1500/SRT2200/SRT3000 UPS in a rack See “Install Rails to 2-Post Rack” on page 2 for instructions on rail installation.
x3
66b s uo08
x3 suo1021a
x4 suo1022a
x3 4
suo1023a
suo1024a
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
suo1025a
suo1026a
SRT1000/SRT1500/SRT2200/SRT3000 UPS with one external battery pack
suo0837b
suo0838b
suo0839b
suo0840b
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
5
Disconnect and remove the battery module from the UPS. See “Tower to rack-mount conversion” on page 3.
suo0835b
suo0836b
34b suo08
Install the SRT1000/SRT1500/SRT2200/SRT3000 UPS with one external battery pack in a rack See “Install Rails to 2-Post Rack” on page 2 for instructions on rail installation.
818b suo0
suo1027a
6
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
suo1029a suo1028a
x6
suo1030a
suo1031a
U PS X LB P suo1032a
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
suo1033a
7
SRT5K/SRT6K UPS CAUTION DAMAGE TO EQUIPMENT OR PERSONNEL • The equipment is heavy. Each APCRBC140 battery module weighs 17 kg (37 lb). • Always practice safe lifting techniques adequate for the weight of the equipment. • Remove the battery modules before installing the UPS. • Use the battery module handle to carefully slide the battery module in or out of the unit. • Do not use the battery module handle to lift or carry the battery module. • Place the UPS on a table to remove the stabilizer brackets. • Always install the UPS at the bottom of the rack. • Always install the XLBP below the UPS in the rack. Failure to follow these instructions can result in equipment damage and minor or moderate injury.
Tower to rack-mount conversion
su08 52b
su 08
su08 49b
8
51b
su08 48b
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
su08
su 08
45 b
46b
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
9
Install the SRT5K/SRT6K UPS in a rack See “Install Rails to 2-Post Rack” on page 2 for instructions on rail installation.
su0
853
c
suo1034a
suo1035a
suo1036a
suo1037a
10
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
suo1038a
suo1039a
SRT5K/SRT6K UPS with one external battery pack
98b
s u0 9
s u08
00b
s u08
97b
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
11
Disconnect and remove the battery module from the UPS. See “Tower to rack-mount conversion” on page 14.
XLBP
su0893b
s u08
94b
UPS
2b su089
Install the SRT5K/SRT6K UPS with one external battery pack in a rack The process for installation of an external battery pack with UPS models SRT8K/SRT10K models is identical to that described for the SRT5K/SRT6K models. See “Install Rails to 2-Post Rack” on page 2 for instructions on rail installation.
s u09
19c
suo1040a
12
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
suo1041a
suo1042a
suo1044a
suo1043a
UPS XLBP
x4
suo1045a
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
suo1046a
13
SRT8K/SRT10K UPS CAUTION DAMAGE TO EQUIPMENT OR PERSONNEL • The equipment is heavy. Each APCRBC140 battery module weighs 17 kg (37 lb). • Always practice safe lifting techniques adequate for the weight of the equipment. • Remove the battery modules before installing the UPS. • Use the battery module handle to carefully slide the battery module in or out of the unit. • Do not use the battery module handle to lift or carry the battery module. • Place the UPS on a table to remove the stabilizer brackets. • Always install the UPS at the bottom of the rack. • Always install the XLBP below the UPS in the rack. Failure to follow these instructions can result in equipment damage and minor or moderate injury.
Tower to rack-mount conversion
s uo0
s uo0
7 84c
7 85b
x4
s uo0
14
7 81b
suo0
7 83a
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
s uo0
7 82b
Install the SRT8K/SRT10K UPS in a rack See “Install Rails to 2-Post Rack” on page 2 for instructions on rail installation.
s uo0
77 3c
x4 x4
suo1047a
x4
suo1048a
Smart-UPS SRT 2-Post Rack-Mount Rail Kit
suo1049a
15
suo1050a
x4 suo1051a
suo1052a
Install the SRT8K/SRT10K UPS with one external battery pack in a rack The process for installation of an external battery pack with UPS models SRT8K/SRT10K models is identical to that described for the SRT5K/SRT6K models. Refer to the installation process “Install the SRT5K/SRT6K UPS with one external battery pack in a rack” on page 12.
Customer support and warranty information is available at the APC by Schneider Electric web site, www.apc.com. © 2017 APC by Schneider Electric. APC, the APC logo, and Smart-UPS are owned by Schneider Electric Industries S.A.S., or their affiliated companies. All other trademarks are property of their respective owners.
EN 990-5470B 3/2017
