Transcript
Application Note Product: TTC-1 App. Note #: 0561 Mod. #: Notes:
Radio: Kenwood TK-7180 Date: 11 Dec 2007 Technician: Mark Goudin
CON-6 – Radio Interface LEAD PIN FUNCTION
RADIO INSTALLATION POINT
Gray
CON-6-1
TR- (Future Use)
Not Connected
Orange Violet Yellow Green Red Black
CON-6-2 CON-6-3 CON-6-4 CON-6-5 CON-6-6 CON-6-7
F2 TR+ (Future Use) Monitor TX MOD Input +13-18 VDC Ground
Pin 20 of DB-25 connector Not Connected Pin 24 of DB-25 connector Pin 6 of DB-25 connector Pin 14 of DB-25 connector Pin 7 of DB-25 connector
White Blue Brown
CON-6-8 CON-6-9 CON-6-10
RX Input PTT F1
Pin 17 of DB-25 connector Pin 12 of DB-25 connector Pin 13 of DB-25 connector
NOTE
CON-2 – F3-F10 Interface Gray Orange Violet
CON-2-1 CON-2-2 CON-2-3
Spare (Future Use) COR F3 or Binary 1
Yellow Green Red Black White Blue
CON-2-4 CON-2-5 CON-2-6 CON-2-7 CON-2-8 CON-2-9
F4 or Binary 2 F5 or Binary 3 F6 or Binary 4 F7 F8 F9
Brown
CON-2-10
F10
Not Connected Pin 8 of DB-25 connector Pin 21 of DB-25 connector
1
Notes: 1. Program the radio with KPG-89D, select “Edit” than “Extended function” then “AUX” set input/output ports as follows, pin 8 output “TOR”, pin 12 output “External PTT”, pin 13 input “CH/GID Select A”, pin 20 input “CH/GID Select C” pin 23 input “CH/GID Select B”, pin 24 input “External Monitor” select the “Remote Zone-CH/GID” tab and set desired channels to be selected by the TTC, close the window and write to radio. This application note was derived using the best information available to us at the time of publication. Midian assumes no responsibility for the accuracy of this document or any damage to equipment resulting from use of this application note.
Midian Electronics, Inc 2030 N. Forbes Blvd. #101 Tucson, AZ 85745 USA Orders: 1-800-MIDIANS (643-4267) Phone: 520-884-7981 Fax: 520-884-0422 E-mail:
[email protected] Website: www.midians.com
2. Program the TTC with the KL3 cable and software, under the “General Parameters” tab, set the COR polarity as low and check the “Enable COR” box then program unit. 3. Jumpers on the TTC are set as follows, JP-1 to pins 2+3, JP-8 to pins 2+3, JP-13 to pins 1+2, JP-14 to pins 1+2, JP-15 open, JP-16 to pins 1+2 and JP-20 to pins 1+2. 4. If 4 channel operation is desired than pin 4, 20, or 22 can be programmed for “CH/GID Select D”, however the DB-25 connector can not be used for programming with KPG-89D.
This application note was derived using the best information available to us at the time of publication. Midian assumes no responsibility for the accuracy of this document or any damage to equipment resulting from use of this application note.
Midian Electronics, Inc 2030 N. Forbes Blvd. #101 Tucson, AZ 85745 USA Orders: 1-800-MIDIANS (643-4267) Phone: 520-884-7981 Fax: 520-884-0422 E-mail:
[email protected] Website: www.midians.com
