Apw5050n Operation Manual

Transcript

50" ATSC/NTSC PLASMA TV APW5050N OPERATION MANUAL Please read this manual carefully before operation. Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. REGULATORY INFORMATION This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CAUTION DO not attempt to modify this product in any way without written authorization from supplier. Unauthorized modification could void the user's authority to operate this product. It is not recommended to keep a certain still image displayed on the screen for a long time as well as displaying extremely bright images on screen. 1 Warning WARNING To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture. Don’t use the apparatus in tropical climates. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. The Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Attention should be drawn to the environmental aspects of battery disposal. Don’t throw used batteries in dustbin. Please contact your retailer in order to protect the environment. Keep minimum distances (5cm) around the apparatus for sufficient ventilation; (Minimum distance around the apparatus for sufficient ventilation.) No naked flame sources, such as lighted candles, should be placed on the apparatus; To prevent the spread of fire, keep candles or other open flames away from this product at all times. The product needs electrostatic prevention. Restart the product when fail to start due to the static caused by product terminals such as TV, AV, HDMI. CAUTION connecting the Power Cord Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and its if appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. The MAINS plug is used as the disconnect device, and the disconnect device shall remain readily operable. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection. 2 Warning FCC Warning Class B Computing Device Information to User This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or TV reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and unit. 3) Connect the equipment into an outlet on a circuit different from that to which the unit is connected. 4) Consult the dealer or an experienced radio/TV technician for help and for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: “How to Identify and Resolve Radio - TV Interference Problems". This booklet is available from the US Government Printing Office, Washington, D.C. 20402, and Stock No. 004-000-00345-4. FCC Warning The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. NOTE: In order for an installation of the product to maintain compliance with the limits for a Class B Device, shielded cables must be used. Manufacture under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories. 3 Safety instructions IMPORTANT SAFETY INSTRUCTIONS 7. Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 8. Do not install near any heat source such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 6. Clean only with a dry cloth. 4 Safety instructions 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 11. Only use the attachments/ accessories specified by the manufacturer. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. ON DISPOSAL -The fluorescent lamp used in this product contain a small amount of mercury. -Do not dispose of this product with general household waste. -Disposal of this product must be carried out in accordance to the regulations of your local authority. NOTE -If the TV feel cold to the touch, there may be a small "flicker" when it is turned on. This is normal, there is nothing wrong with TV. -Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However there have no adverse effect on the monitor's performance. -Avoid touching the screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effect on the screen. 5 Getting Started Using the remote control When using the remote control, aim it at remote sensor on the television. If there is an object between the remote control and the signal remote sensor on the unit, the unit may no operate.  Point the remote control at the REMOTE SENSOR located on the television.  When using this television in a very brightly lit area, the infrared REMOTE CONTROL SENSOR may not work properly.  The recommended effective distance for using the remote control is about 7 metres. Change the remote control battery 1. Open the lid of the remote control battery compartment. 2. Insert two size-AAA batteries. Ensure that the batteries are inserted with the positive and negative terminals in the correct direction corresponding to the (+) and (-) marks in the battery compartment. 3. Push up the cover until the lock clicks. Battery replacement You will need to install the supplied batteries into the remote control to make it operate following the instruction below. When the batteries become weak, the operating distance of the remote control will be greatly reduced and you will need to replace the batteries. Notes on Using Batteries The use of the wrong type of batteries may cause chemical leaks and/or explosion. Please note the following:  Always ensure that the batteries are inserted with the positive and negative terminals in the correct direction as shown in the battery compartment.  Different types of batteries have different characteristics. Do not mix different types.  Do not mix old and new batteries. Mixing old and new batteries will shorten battery life and/or cause chemical leaks from the old batteries.  When batteries fail to function, replace them immediately.  Chemicals which leak from batteries may cause skin irritation. If any chemical matter seeps out of the batteries, wipe it up immediately using a dry cloth.  Due to varying storage conditions, the battery lift for the batteries included with your television may be shorten. If the remote control is not used for a long period of time, remove the batteries.  The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION:  There is a danger of a explosion if batteries are incorrectly replaced.  Replace only with the same or equivalent type. 6 Connection and setup Cable Installation Before the installation and use, please read carefully the relevant content in "Notice for Maintenance and Safety". 1. Take the TV from the wrapping package and put it in a drafty and flat place. NOTE:  When you plug or unplug the TV, computer or other equipments, you must make sure that the AC power has been already shut down; when unplugging the power cable or signal cable, please hold the plug (the insulated part), do not draw the body of the cable. 2. The RF output terminal can be connected with the RF input port of the TV. 3. The output AV terminal of DVD can be connected with the AV input port of the TV through AV cable. 4. Connect one end of the VGA cable with the VGA port on computer, connect the other end of the VGA cable with the VGA port on the TV, and tighten the bolts clockwise on the each end of VGA cable. NOTE:  While connecting the 15-pin VGA, please do not insert the plug overexertedly, for fear the pin might be broken. 5. Connect one end of the HDMI cable with HDMI output port, connect the other end of the HDMI cable with the HDMI port on the TV. NOTE:  While connecting the HDMI, please aim at carefully, do not insert overexertedly, for fear the pin might be broken. 6. Check and make sure that all AV cables are connected with the corresponding ports correctly. 7. Connect the AC power cable with 100V~240V AC power supply. NOTE:  The range of power input for the TV is 100V~240V/50Hz-60Hz, do not connect the TV power input port with the AC power out of the above range.  Please hold the insulated part of the plug when you are unplugging the power cable, do not touch directly the metallic part of the cable. 7 Remote Control The buttons of the original remote control are as following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 8 : Press this key to switch power on or off. DISP: Press this key to display the setting on the screen. MUTE: Press this key to mute or restore sound. Numeric keys: Press these keys to select a channel directly or enter the numbers in the menus. INPUT: Press this key to switch source. DIGIT key: Press this key to select – in DTV. P.MODE: Press this key to select the desired picture mode. S.MODE: Press this key to select the desired sound mode. MENU: Press this key to enter the menu screens. EXIT: Press this key to exit from the current menu. OK: Press to select or confirm sub menu of the OSD. UP/DOWN: Press these keys to select the desired items in the menu. LEFT/RIGHT: Press these keys to select the desired items in the menu, or enter the selected. VOL+/VOL-: Press these keys to adjust the volume. CH+/CH-: Press these keys to select channels or move to the higher or lower item in the menus. SLEEP: Press this key to set the sleep timer. ZOOM: Press this key to select different image sizes. CC: Press this key to select the CC Mode. Remote Control 18. MTS: When stereo program is received, press this key to switch sound system between mono and stereo. When SAP program is received, press this button to switch sound system between mono and SAP. When stereo and SAP program is received, press this key to switch among mono, stereo and SAP. Press this key to show the list of audio languages available for the current channel in DTV. 19. COLOR BUTTONS: Red/ green/ yellow/ blue key navigation link. GUIDE: Press to view the information of EPG in digital program. FAV: Press this key to display favl list in TV mode. LIST: Press this key to display the channel list in TV mode. ANT: Press to select the air or cable. 20. PC: Press to enter into PC mode. 21. LOCK: Press to enter into LOCK menu. 22. HDMI: Press to enter into HDMI mode. 23. LAST: Press to switch between the last viewed and current program. NOTE:  All pictures in this manual are examples, only for reference, actual product may differ from the pictures.  The buttons not mentioned here are not used. 9 Basic Operation Turning on and off the TV • Turn on the TV Connect the AC input cable. At this time the TV enter standby mode. • Turn off the TV Press on the remote control to enter/exit standby mode. When a complete turning off is required, please unplug the power cable from the power socket. • No signal There is No Signal menu on screen when there is no input signal. In TV/DTV/VGA mode, if there is no signal in ten minutes, the TV will turn off automatically. Choosing a TV channel • Using the CH+/CH- on the panel of TV or on the remote control. Press CH+ to increase channel number. Press CH - to decrease channel number. • Using 0- 9 digital buttons and - button. You can select the channel number by pressing 0 to 9. (In TV mode) • Example To select - channel (e.g. Channel 5): Press 5. To select -- channel (e.g. Channel 20): Press 2 and 0 in a short time. To select --.- channel (e.g. Channel 20.5): Press 2, 0, - and 5 in a short time. Volume adjustment • Press VOL+/- to adjust the volume. • If you want to switch the sound OFF, press the . • You can release mute by pressing or VOL+. Input Source You can select the input source by pressing the INPUT button on the remote control. PressŸ/źbutton to cycle through the input source, and press OK button to confirm. NOTE:  The picture is just for reference. Please operate with the OSD MENU of concrete TV and refer to the AV terminal board. 10 Menu Operation Menu overview Press MENU key to display Menu, and press UP (Ÿ) or DOWN (ź) to select sub menu. Press OK key to sub menu. MENU key ¾ Press MENU key to open & close Menu. ¾ Press EXIT key to close the current Menu and open the previous Menu. ¾ Press MENU or EXIT key on the remote control unit to cancel the Menu function. ¾ Use Ÿ/ź keys to select desired parameter for adjustment, and adjust parameter by the using Ż/Ź keys. 1. PICTURE Menu Enter PICTURE Menu, you can select Picture Settings, Screen Settings, PC Setting, Color Temperature, Advanced Picture Settings and Return items by pressing Ÿ/źkeys. ¾ Press Ÿ/ź keys to select different setting. ¾ Press OK keys to enter the Picture Settings menu. ¾ Press OK keys to enter the Screen Settings menu. ¾ Press OK key to enter the PC Settings menu if you are in VGA source. ¾ Press Ż/Ź keys to select a suitable color temperature to display. ¾ Press OK key to enter the Advanced Picture Settings menu. ¾ Press EXIT key to return to the main menu. 1.1. Picture Settings Menu 11 ¾ Press Ÿ/źkeys to select different setting. ¾ Press Ż/Ź keys to select the picture mode. If [User] is selected, adjust the items. (also see below) ¾ Press Ż/Ź keys to adjust brightness. ¾ Press Ż/Ź keys to enhance and reduce the contrast. ¾ Press Ż/Ź keys to increase and decrease the color saturation. ¾ Press Ż/Ź keys to select a suitable Tint to display. ¾ Press Ż/Ź keys to sharpen or soften the picture. ¾ Press EXIT key to return to the main menu. 1.2. SCREEN SETTINGS Menu ¾ PressŸ/ź keys to select different setting. ¾ Press Ż/Ź keys to select the mode of Screen Size. ¾ Press OK key to select the Auto Wide mode on or off. ¾ Press Ż/Ź keys to adjust the Horizontal Position. ¾ Press Ż/Ź keys to adjust the Vertical Position. ¾ Press EXIT key to return to the main menu. 1.3. VGA SETTINGS Menu ¾ Press Ÿ/ź keys to select different setting. ¾ Press OK key for a moment to restore the window. ¾ Use Ż/Ź keys to adjust the horizontal position of the window. ¾ Use Ż/Ź keys to adjust the vertical position of the window. ¾ Use Ż/Ź keys to adjust the clock of the window. ¾ Use Ż/Ź keys to adjust the phase of the window. ¾ Press EXIT key to return to the main menu. ** Power off both the computer and the TV before making any connection. 1.4. ADVANCED PICTURE SETTINGS Menu ¾ Press Ÿ/ź keys to select different setting. ¾ Use Ż/Ź keys to select the mode of SABC. ¾ Press OK key to select the Film Mode. ¾ Press Ż/Ź keys to select a suitable mode of the Noise Reduction. ¾ Press Ż/Ź keys to select a suitable mode of the MPEG Noise Reduction. ¾ Press EXIT key to return to the main menu. 12 2. SOUND Menu Enter SOUND menu, you can select Sound Settings, Surround Mode, Analog Sound, Digital Sound and Return items by pressing Ÿ/ź keys. ¾ Press Ÿ/ź keys to select different setting. ¾ Press OK keys to enter the Sound Settings menu. ¾ Press OK keys to select the Surround Mode. ¾ Press Ż/Ź key to select the mode of Analog Sound if you are in ATV source. ¾ Press Ż/Ź key to select the mode of Digital Sound if you are in DTV source. ¾ Press EXIT key to return to the main menu. 2.1. SOUND SETTINGS Menu ¾ Press Ÿ/ź keys to select different setting. ¾ Press Ż/Ź keys to select the mode of Sound Settings. If [User] Picture Preset is selected, go to Picture Setting and adjust the items. (also see below) ¾ Press Ż/Ź keys to enhance and reduce the parameter of bass. ¾ Press Ż/Ź keys to enhance and reduce the parameter of treble. ¾ Press Ż/Ź keys to adjust the audio balance between left and right channels. ¾ Press EXIT key to return to the main menu. 3. CHANNEL Menu The CHANNEL menu is available only in ATV and DTV source, followed by the CHANNEL MENU, Channel List, Channel Settings, Signal Type and Auto Channel Search and Return are the items, which can be selected by pressing Ÿ/ź keys. ¾ Press Ÿ/ź keys to select the different items. ¾ Press OK key to enter the Channel List menu. ¾ Press OK key to enter the Channel Setting menu. ¾ Press Ż/Ź keys to select the signal type. ¾ Press OK key for a moment to enter the auto channel search. ¾ Press EXIT key to return to the main menu. 13 3.1. CHANNEL LIST Menu ¾ Press Ÿ/ź keys to choose the channel which you want to select. ¾ Press OK key to enter the channel which you select. ¾ Press EXIT key to return to the main menu. 3.2. CHANNEL SETTINGS Menu ¾ Press Ÿ/ź keys to select the different items. ¾ Press CH+/CH- keys to choose the channel which you want to edit. ¾ Press OK key to select the channel if in the channel list. ¾ Press Ż/Ź keys to choose the character which you want to modify. Press Ÿ/ź button to select the characters to represent the station name. ¾ Press OK key to enter the Favorite Setting menu. Press Ÿ/ź keys to choose the channel which you want to select. Press OK key to select the channel is the favorite channel or not. ¾ Press EXIT key to return to the main menu. 3.3. AUTO CHANNEL SEARCH Menu Press OK key to start or stop the automatic tuning process. After a few minutes the tuning will finish and the first station stored will show on the TV screen. Change channels by pressing CH+/CH- keys. Notice: Only after finishing Auto Search, channels will be sorted. If you break the process during the auto search period, channels will be searched and stored, however, the channel will not be sorted into their correct channel order. 14 4. PARENTAL CONTROL Menu Followed by the PARENTAL CONTROL MENU, Lock Parental Control, V-CHIP, Change Password, Front Panel Lock and Return are the items, which can be selected by pressing Ÿ/ź keys. Press OK key to enter the item. ¾ Change password if use this function in the first time. ¾ To change password, you need to enter the new password and confirm password, which consists of only digits. The new password and Confirm password must be same. ¾ Press EXIT key to return to the main menu. ¾ Press OK key to enter the item. ¾ Press the Numeric keys to enter password. Then you can press Ÿ/ź keys to select the other items. ** The super password is 1506. ¾ Press OK keys to enter the V-CHIP menu. ¾ Press OK key to enter the Change Password menu. ¾ Press OK key to select if lock the front panel or not. ¾ Press EXIT key to return to the main menu. 4.1. V-CHIP Menu ¾ Press Ÿ/ź keys to select the different items. ¾ Press OK key to enter the US V-Chip, Canada V-Chip, Downloadable Rating and Clear Downloadable Data menu. ¾ Press Ÿ/ź keys to select rating which you want to lock. ¾ Press OK key to select the rating lock or not. ¾ Press EXIT key to return to the main menu. 15 4.2. Change Password Menu ¾ Press OK key to enter the menu. ¾ To change password, you need to enter the old password. After enter old password, you can enter the new password and confirm password, which consists of only digits. The new password and Confirm password must be same. ¾ Press EXIT key to return to the main menu. 5. SETUP Menu Enter SETUP menu, you can select Closed Caption, Menu Language, Clock and Return items by pressing Ÿ/ź keys. ¾ Press Ÿ/ź keys to select the different items. ¾ Press OK key to enter the Closed Caption menu. ¾ Press Ż/Ź keys to select the menu language. ¾ Press OK key to enter the Clock menu. ¾ Press EXIT key to return to the main menu. 5.1. CLOSED CAPTION Menu ¾ Press Ÿ/ź keys to select the different items. ¾ Press Ż/Ź keys to select the Caption Display off or on. ¾ Press Ż/Ź keys to select the Analog Caption Type. ¾ Press Ż/Ź keys to select the Digital Caption Type. This item is available only in DTV source. ¾ Press Ż/Źkeys to select the Digital CC Preset. This item is available only in DTV source. ¾ Press OK keys to enter the Digital CC Style menu. This item is available only in DTV source. ¾ Press EXIT key to return the main menu. 16 5.1.1 DIGITAL CC STYLE Menu ¾ Press Ÿ/ź keys to select the different items. ¾ Press Ż/Ź keys to select the CC Size. ¾ Press Ż/Ź keys to select the CC Font. ¾ Press Ż/Ź keys to select the CC Opacity. ¾ Press Ż/Ź keys to select the CC Color. ¾ Press Ż/Ź keys to select the CC Background Opacity. ¾ Press Ż/Ź keys to select the CC Background Color.. ¾ Press EXIT key to return the main menu. 5.2. CLOCK Menu ¾ Press Ÿ/ź keys to select the different items. ¾ Press Ż/Ź keys to select the Time Zone. ¾ Press Ż/Ź keys to select the Daylight Saving mode on or off. ¾ Press Ż/Ź keys to select the Auto Clock on or off. ¾ Press OK key to select the items and then press Ż/Ź. Keys to change the value. ¾ The item of Data of Week will change with the set of Setup Time. ¾ Press EXIT key to return the main menu. 6. OTHERS Menu In the OTHERS Menu, Blue Back, No Signal Power Off, No Operation Power Off, All Reset and Return are displayed on the screen. Use Ÿ/ź keys to select. ¾ PressŸ/ź keys to select different items. ¾ Press OK keys to select the blue back on or off. ¾ Press OK keys to select if the TV set power down or not when no signal. ¾ Press OK keys to select if the TV set power down or not when no operation. ¾ Restore to the original setting by press OK. ¾ Press EXIT key to return the main menu. 17 Troubleshooting Guide TV Troubleshooting Before contrast the service technician, perform the following simple checks. If any program still persists, unplug the TV and calling for serving. PROBLEM POSSIBLE SOLUTION - Check whether the main plug has been connected to a wall let. No sound and picture - Check whether you have pressed the POWER button on the front of TV set. - Check the picture contrast and brightness settings. - Check the volume. - Sound muted? Press the MUTE button. Normal picture but no - Try another channel, the problem may be with the sound broadcast. - Are the audio cables installed properly? - Check to see if there any object between the product and remote control Causing obstruction. The remote control does - Are batteries installed with correct polarity (+ to +, not work - to -). - Correct remote operating mode set: TV, VCR etc.? - Install new batteries - Is the sleep timer set? Power is suddenly turned - Check the power control settings. Power interrupted. off - No broadcast on station tuned with auto activated. - This is normal, the image is muted during the Picture appears slowly product startup process. Please contact your service after switching on center, if the picture has not appeared after five minutes. - Adjust the color in menu option. - Keep a sufficient distance between the product and the VCR. No or poor color or poor - Try another channel, the problem may be with the picture broadcast. - Are the VIDEO cables installed properly? - Activate the any function to restore the brightness of the picture. Horizontal/vertical bars or - Check for local interference such as an electrical picture shaking appliance or power tool. - Station or cable product experiencing problems. Tune to another station. Poor reception on some - Station signal is weak, reorient antenna to receive channels weaker station. - Check for sources of possible interference. Lines or streaks in - Check the antenna (Change the direction of the pictures antenna). No output from one of the - Adjust balance in menu option. speakers 18 Troubleshooting Guide NOTE: There is a problem in VGA mode (Only VGA mode applied). PROBLEM The signal is out of range. Vertical bar or stripe on back ground & Horizontal Noise & Incorrect position. Screen color is unstable or single color. POSSIBLE SOLUTION - Adjust resolution, horizontal frequency, or vertical frequency. - Check it whether the signal cable is connected or loose. - Check the input source. - Work the auto configure or adjust clock, phase, or H/V position. - Check the signal cable. - Reinstall the PC video card. Maintenance Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the screen 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then used it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Disposal of old electrical appliances The European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. 19 Specification of product Item Color System Specification NTSC, ATSC Sound System M VGA mode supported VGA/SVGA/XGA/WXGA (60Hz) COMPONENT mode supported 480i, 480p, 720p, 1080i,1080p HDMI mode supported Including VGA mode and signal with high definition, namely, VGA/SVGA/XGA/WXGA (60Hz), 480i, 480p, 720p,1080i, 1080p Audio Output Consumption 2x8W AV Input SVIDEO 2 line 1 line COMPONENT Input 2 lines VGA Input 1 line HDMI Input 2 lines PDP panel' resolution 1365x768 Voltage Input 100V~240V/50Hz-60Hz 480W Rated Power Consumption 20