Transcript
Arbitrary Waveform Generators AWGSYNC01 Synchronization Hub Datasheet Coherent optical
The AWGSYNC01 enables the multi-instrument synchronization of up to four AWG70001A or AWG70002A units allowing up to eight channels to be aligned to the same clock, pattern jump and trigger inputs. The AWGSYNC01 requires no additional software and allows for the rapid and consistent synchronization of multiple devices. The AWGSYNC01 provides calibration ports to deskew up to four AWG70000 instruments to within ±10ps. After the deskew process the AWGSYNC01 can repeatedly return to within ≤5 ps of the same deskew point.
Key performance specifications Random Jitter (typical): 315 fsRMS Total jitter (typical): 13 psp-p at 12.5 Gb/s Instrument to instrument skew: ±10 ps
Today's high speed and increasingly Web-driven world is pushing the demand for short and long haul coherent optical development. Phase modulation, high baud rate, high sample rate, bandwidth, and resolution are all critical to optical applications. Tektronix understands the challenges and inconsistencies of coherent optical testing and offers a reliable, easy to set up and high performance tool set for optical testing, waveform generation and calibration. Generating the desired signal is only the first challenge in coherent optical. The quality of the signal, low EVM's, and having a clear, open eye is crucial. Complex quadrature modulations, such as PAM-4, require synchronized output from multiple AWG70000 instruments. The AWGSYNC01 can synchronize multiple single-channel AWG70000 instruments, at the maximum 50 Gs/s sample rate, to output synchronized baseband signals with low EVM and 32 Gbaud performance. The AWGSYNC01 streamlines the complex multiple instrument signal synchronization alignment process, resulting in synchronized signals with a high rate of repeatability and with low jitter.
Skew repeatability/accuracy: ≤5 ps
Key features Synchronize signal output from two to four AWG70000 instruments (providing two to eight signal outputs) Synchronize to within ±10 ps Trigger all channels to the same resolution
Applications Wideband RF/MW for communications and defense electronics Validation and compliance testing of high speed silicon and communications devices Coherent optical research Leading edge research in electronics, physics and chemistry
High speed serial For high-speed serial applications the AWG70000A Series offers the industry's best solution for addressing challenging signal stimulus issues faced by digital designers who need to verify, characterize, and debug complex digital designs. The file-based architecture uses direct synthesis to create complex data streams and gives users a simple, repeatable, and flexible way to solve the toughest signal generation challenges in highspeed serial communication applications. The AWGSYNC01 lets users synchronize multiple AWG instruments to output signals for complex or multi-lane standards such as HDMI and MIPI.
Research applications Advanced research applications such as quantum computing, mass spectroscopy, MEMS, NEMS, and particle physics often demand the precise alignment of multiple simultaneous triggering, precompensation, or I/Q generation signals, all with low jitter. AWG70000 series instruments, used with the AWGSYNC01 Synchronization Hub, provide fast and repeatable results. Day to day experimental setups require no additional equipment for synchronization. The AWGSYNC01 comes with all required phase-stable and delaymatched calibration and clock cabling needed to start synchronizing straight out the box. You can use the clock out signal from the Master AWG70000 instrument to synchronize the output signals, or use an external clock reference signal for higher precision when needed.
Performance you can count on Depend on Tektronix to provide you with performance you can count on. In addition to industry-leading service and support, this product comes backed by a standard one-year warranty.
www.tektronix.com 1
Datasheet
Specifications General Jitter Random Jitter (typical)
315 fs RMS
Total jitter (typical)
13 psp-p at 12.5 Gb/s
Skew Instrument to instrument skew ±10 ps Skew repeatability/accuracy
≤5 ps After changes of sample rate or power cycle and within ±5 °C from deskew calibration.
Inputs, outputs Calibration Ports
Four SMA type connectors used to deskew the instrument signal delays. Only use the supplied matched silver calibration cables with these connectors when deskewing the AWG70000 instrument signal outputs.
Trigger Inputs (A, B)
External trigger inputs
Connector
SMA
Number of trigger inputs
2
Impedance
50 Ω or 1 kΩ selectable
Polarity
Positive or negative selectable
Input voltage range
50 Ω: <5 VRMS 1 kΩ: ±10 VRMS
Threshold range
-5.0 V to 5.0 V
Threshold resolution
0.1 V
Minimum trigger pulse width
20 ns
Trigger holdoff
>1.4 μs
Trigger delay to analog output Asynchronous trigger mode: 32,480 / (2 * fclk) ±20 ns Synchronous trigger mode: 30,880 / (2 * fclk) ±20 ns fclk is the frequency of the DAC sampling clock The DAC sampling clock frequency is displayed on the clock settings tab when the external clock output is enabled. Trigger asynchronous jitter
80/sampling clock frequency The asynchronous jitter performance is directly proportional the sync clock out frequency. The sync clock out is derived from the DAC sampling clock. The DAC sampling clock frequency is displayed on the clock settings tab when the external clock output is enabled.
Trigger synchronous jitter
Clock In = 12.5 GHz: 300 fsRMS, 4.2 ps RJp-p BER@10-12 Variable Reference In = 156.25 MHz: 400 fsRMS, 5.6 ps RJp-p BER@10-12 Fixed Reference In = 10 MHz: 1.7 psRMS, 23.8 ps RJp-p BER@10-12 Sample rate = 25 GS/s
Sync to AWG (1-4)
Communication ports used by to synchronize all connected AWG70000 instruments. The AWG70000 connected to Port 1 is the Master AWG70000, which sets up and controls synchronization of the connected instruments. You must connect an AWG70000 to Port 1. AWG70000 instruments connected to Ports 2 through 4 are Slave AWG70000 instruments. Use the supplied orange cable assemblies to connect these ports to the AWG70000 instruments.
2 www.tektronix.com
AWGSYNC01 Inputs, outputs Clock in from Master AWG
Synchronizing clock signal input from the master AWG70000 Clock Out port, or from an external clock signal source.
Connector
SMA
Input impedance
50 Ω, AC coupled
Input frequency range
6.25 GHz to 12.5 GHz
Input amplitude
+5 dBm to +10 dBm
Clock Out to AWG Clock In Connector
SMA
Impedance
50 Ω, AC coupled
Frequency range
6.25 GHz to 12.5 GHz
Output amplitude
+5 dBm to +10 dBm
Sync Clock Out Connector
SMA
Impedance
50 Ω, AC coupled
Frequency
10 MHz ±(1 ppm + aging)
Output amplitude
1.0 V ±150 mVp-p
Pattern Jump In Number of jump destinations
256
Connector
15-pin D-sub female connector on rear panel
Input levels
3.3 V LVCMOS 5 V TTL compliant (input impedance pull up to 5 V by 1 kΩ resistor)
Strobe
Polarity: Data is clocked in on negative edge Minimum pulse width: 64 ns
Latency to analog output
102,125/fclk +20 ns ± 20 ns The DAC sampling clock frequency is displayed on the clock settings tab when the external clock output is enabled
Holdoff time
>18 μs Strobe hold off is the amount of delay required at the end of a waveform before another strobe pulse can be processed
Physical characteristics Dimensions Height
44.45 mm (1.75 in)
Width
460.5 mm (18.13 in)
Depth
603 mm (23.76 in)
Weight Instrument only
5.4 kg (12 lb)
With packaging
9.1 kg (20 lb)
Cooling clearance Top, bottom, left, right
0 mm (0 in)
Rear
50 mm (2 in)
Power AC line input
100 to 240 V AC, 50/60 Hz
Consumption
110 W
www.tektronix.com 3
Datasheet Environment Temperature Operating
0 °C to +50 °C (32 °F to +122 °F)
Nonoperating
-20 °C to +60 °C (140 °F to +150 °F)
Humidity Operating (noncondensing)
5% to 90% relative humidity (% RH) at up to 30 °C 5% to 45% relative humidity above 30 °C up to 50 °C
Nonoperating (noncondensing)
5% to 90% relative humidity (% RH) at up to 30 °C 5% to 45% relative humidity above 30 °C up to 60 °C
Altitude Operating
Up to 3,000 meters (9,843 feet) Derate maximum operating temperature by 1 °C per 300 meters above 1500 meters.
Nonoperating
Up to 12,000 meters (39,370 feet) Derate maximum operating temperature by 1 °C per 300 meters above 1500 meters.
Regulatory Safety
UL61010-1, CAN/CSA-22.2, No.61010-1, EN61010-1, IEC61010-1
EMC Emissions
IEC61326, EN55011 (Class A), IEC61000-3-2, IEC61000-3-3
EMC Immunity
IEC61326, IEC61000-4-2/3/4/5/6/11
Regional certifications
Europe: EN61326 Australia/New Zealand: AS/NZS 2064
4 www.tektronix.com
AWGSYNC01
Ordering information Models AWGSYNC01
Synchronizes signal output on up to four AWG70001A and/or AWG70002A instruments
Standard Accessories Standard accessories 071-3292-xx
AWGSYNC01 Safety and Installation Instructions
174-6157-xx
AWG synchronization communication cables (set of 4 cables, orange)
174-6568-xx
Phase stable clock cables (set of 4 cables, blue)
174-6606-xx
Calibration deskew cables (set of 4 cables, silver)
Power cord
Specify power cord option at time of order
Warranty One year parts and labor
Options Power plug options Opt. A0
North America power plug (115 V, 60 Hz)
Opt. A1
Universal Euro power plug (220 V, 50 Hz)
Opt. A2
United Kingdom power plug (240 V, 50 Hz)
Opt. A3
Australia power plug (240 V, 50 Hz)
Opt. A5
Switzerland power plug (220 V, 50 Hz)
Opt. A6
Japan power plug (100 V, 50/60 Hz)
Opt. A10
China power plug (50 Hz)
Opt. A11
India power plug (50 Hz)
Opt. A12
Brazil power plug (60 Hz)
Opt. A99
No power cord
www.tektronix.com 5
Datasheet Service options Opt. C3
Calibration Service 3 Years
Opt. C5
Calibration Service 5 Years
Opt. D3
Calibration Data Report 3 Years (with Opt. C3)
Opt. D5
Calibration Data Report 5 Years (with Opt. C5)
Opt. R3
Repair Service 3 Years (including warranty)
Opt. R3DW
Repair Service Coverage 3 Years (includes product warranty period). 3-year period starts at time of instrument purchase
Opt. R5
Repair Service 5 Years (including warranty)
Opt. R5DW
Repair Service Coverage 5 Years (includes product warranty period). 5-year period starts at time of instrument purchase
Opt. S1
On-site Service 1 Year
Opt. S3
On-site Service 3 Years (with R or C options)
Cables and accessories are not covered by the instrument warranty and Service Offerings.
Recommended accessories AWGRACK
Rack mount kit for AWG70000A Series instruments and AWGSYNC01
Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.
Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.
ASEAN / Australasia (65) 6356 3900 Belgium 00800 2255 4835* Central East Europe and the Baltics +41 52 675 3777 Finland +41 52 675 3777 Hong Kong 400 820 5835 Japan 81 (3) 6714 3010 Middle East, Asia, and North Africa +41 52 675 3777 People's Republic of China 400 820 5835 Republic of Korea 001 800 8255 2835 Spain 00800 2255 4835* Taiwan 886 (2) 2722 9622 * European toll-free number. If not accessible, call: +41 52 675 3777
Austria 00800 2255 4835* Brazil +55 (11) 3759 7627 Central Europe & Greece +41 52 675 3777 France 00800 2255 4835* India 000 800 650 1835 Luxembourg +41 52 675 3777 The Netherlands 00800 2255 4835* Poland +41 52 675 3777 Russia & CIS +7 (495) 6647564 Sweden 00800 2255 4835* United Kingdom & Ireland 00800 2255 4835*
Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777 Canada 1 800 833 9200 Denmark +45 80 88 1401 Germany 00800 2255 4835* Italy 00800 2255 4835* Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90 Norway 800 16098 Portugal 80 08 12370 South Africa +41 52 675 3777 Switzerland 00800 2255 4835* USA 1 800 833 9200 Updated 10 April 2013
For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit www.tektronix.com. Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies. 17 Jul 2014
www.tektronix.com
76W-30652-0
