Transcript
Control Dock for iPod®
ASD-1R OPERATING INSTRUCTIONS
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
ENGLISH
FCC INFORMATION (For US customers)
CAUTION: To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. When setting up this product, make sure that the AC outlet you are using is easily accessible.
1. PRODUCT This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
3. NOTE This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the product into an outlet on a circuit different from that to which the receiver is connected. • Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help. This Class B apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
I
ENGLISH NOTE ON USE: • Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack. • Handle the power cord carefully. Hold the plug when unplugging the cord. • Keep the apparatus free from moisture, water, and dust. • Unplug the power cord when not using the apparatus for long periods of time. • Do not obstruct the ventilation holes. • Do not let foreign objects into the apparatus. • Do not let insecticides, benzene, and thinner come in contact with the apparatus. • Never disassemble or modify the apparatus in any way.
CAUTION: • Minimum distances around the apparatus for sufficient ventilation. • The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.. • No naked flame sources, such as lighted candles, should be placed on the apparatus. • Attention should be drawn to the environmental aspects of battery disposal. • The use of apparatus in tropical and/or moderate climates.
II
ENGLISH • DECLARATION OF CONFORMITY We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55022, EN55024, EN61000-3-2 and EN61000-3-3. Following the provisions of 73/23/EEC, 2004/108/EC and 93/68/EEC Directive.
III
ENGLISH A NOTE ABOUT RECYCLING: This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with the local recycling regulations. When discarding the unit, comply with local rules or regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning chemical waste. This product and the accessories packed together constitute the applicable product according to the WEEE directive except batteries.
IV
ENGLISH
Getting Started Contents
Accessories Check that the following parts are attached in addition to the main unit:
Getting Started Accessories ·······················································································1 Before using······················································································2 Part names and functions ·······························································2 Top panel/Rear panel ·······································································2 Bottom panel ···················································································2
q Operating Instruction ................................................................1 w Service Station List ...................................................................1 e AC Adapter (KSAFD1200120W1UV) .........................................1 r Universal Adapter (5 types) ..............................................1 each t AV/Control Cable (Cable length: Approx. 6 ft/2 m) ....................1 y System Connector Cable
Connecting Other Sources
(Cable length: Approx. 3 ft/1 m) ................................................1
Mounting the universal adapter on the control dock···················3 Connection to devices equipped with DOCK CONTROL terminals ·····························································4 Connecting the ASD-1R and a device equipped with a system control (SYSTEM CONNECTOR) terminal ·····················5
e
(For U.S.A. & Canada model)
Functions and operation When the ASD-1R and a device equipped with a DOCK CONTROL terminal are connected ······································6 When the ASD-1R and a device equipped with a system control (SYSTEM CONNECTOR) terminal are connected ···········6 Remote control buttons and operations ··········································7
r
Troubleshooting ···············································································8
(For Europe model) t
(For China model) y
NOTE: • Do not use any AC adapter other than the specified one. Doing so could result in fires or electric shock. • The included AC adapter is exclusively for use with this unit. Never use it with other equipment.
Specifications ···················································································9
1 ENGLISH
ENGLISH Getting Started
Getting Started
q Dock connector w Universal adapter slot e CONTROL terminal (stereo mini plug) r AUDIO OUT terminals t S-VIDEO OUT terminal y DC IN terminal
Before using Pay attention to the following before using this unit: • Moving the unit To prevent short-circuits or damaged wires in the connection cables, always unplug the power supply cord and disconnect the connection cables between all other audio components when moving the unit. • Cautions on using mobile phones Using a mobile phone near this unit may result in noise. If so, move the mobile phone away from this unit when using it.
Bottom panel
• Store these instructions in a safe place. After reading, store this instructions along with the warranty card in a safe place. • Note that the illustrations in these instructions may differ from the actual unit for explanation purposes.
Part names and functions Top panel/Rear panel
u
iu
u Fixing screw holes
Use the fixing screw holes (two) to fix the control dock by screw. (Usable screws: M3, max. 15 mm in length)
i Communication mode selector (MODE SELECT)
q w
e
r
t y
2 ENGLISH
ENGLISH
Connecting Other Sources Mounting the universal adapter on the control dock Mount the included universal adapter suited for your iPod® to the control dock’s universal adapter slot.
Adapter
iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Main unit Bottom surface of universal adapter
Stamped indication
Stamped indication
iPod connectable to the ASD-1R
iPod 20GB
4th generation iPod 20GB
iPod 40GB
4th generation iPod 40GB
mini
iPod mini
Photo 20, 30GB
iPod Photo 30GB/iPod 20GB with color display
Photo 60GB
iPod Photo 60GB/iPod 40GB with color display
• A genuine iPod dock adapter can be mounted on this ASD-1R. • To connect an “iPod nano” or 5th generation iPod, use the dock adapter included with the iPod. • The 3rd generation iPod (with Dock Connector) requires the Apple iPod Universal Dock Adapter 3-Pack that fits your iPod model (separately available from Apple Computer, Inc.) in order to be connected to the ASD-1R.
3 ENGLISH
ENGLISH Connecting Other Sources
Connecting Other Sources
Connection to devices equipped with DOCK CONTROL terminals The iPod can be operated from an amplifier or system device equipped with a DOCK CONTROL terminal connected to the ASD-1R. AC outlet (wall) AC 120 V, 60 Hz (For U.S.A. & Canada model) AC 230 V, 50 Hz (For Europe model) AC 220 V, 50 Hz (For China model)
AC Adapter (Included)
Monitor
1
Set the MODE SELECT switch on the ASD-1R’s bottom panel to “DOCK CONTROL”.
2
Connect as shown at the left.
Also refer to the operating instructions of the device being connected.
3
Connect the included AC adapter to the ASD-1R’s DC IN terminal and plug the AC adapter into a power outlet.
4
Load the iPod onto the ASD-1R.
S VIDEO IN
or
Device equipped with dock control terminal
S VIDEO IN
(Viewing iPod images) AUDIO IN L
L
L
R
R
R
DOCK CONTROL
AV/Control cable (Included)
Signal direction Audio signal
OUT
Video signal
IN
OUT
IN
4 ENGLISH
NOTE: Be sure to switch the communications mode before turning on the ASD-1R’s power. The communications mode will not switch if the MODE SELECT switch is operated while the power is on.
ENGLISH Connecting Other Sources
Connecting Other Sources
Connecting the ASD-1R and a device equipped with a system control (SYSTEM CONNECTOR) terminal The iPod can be operated using the system remote control unit equipped with system control (SYSTEM CONNECTOR) terminal connected to the ASD-1R. Use the system remote control unit’s cassette deck or CD recorder buttons to operate the iPod. For details, see “Remote control buttons and operations” (
Page 7).
AC outlet (wall)
AC Adapter (Included)
AC 120 V, 60 Hz (For U.S.A. & Canada mode) AC 230 V, 50 Hz (For Europe model) AC 220 V, 50 Hz (For China model) Monitor S-Video cable
S VIDEO IN
(Viewing iPod images) Device equipped with system control (SYSTEM CONNECTOR) terminal Pin-plug cable
Switch the MODE SELECT switch on the ASD-1R’s bottom panel.
TAPE, CD-R: Set the MODE SELECT switch to “TAPE” when connected to a cassette deck, to “CDR” when connected to a CD recorder.
2
Connect as shown at the left.
Be sure the MODE SELECT switch is set to the same position in step 1 as the input terminal used for connection. Also refer to the operating instructions of the device being connected.
3
Connect the included AC adapter to the ASD-1R’s DC IN terminal and plug the AC adapter into a power outlet.
4
Load the iPod onto the ASD-1R.
TAPE PB or CD-R PB
L
L
L
R
R
R SYSTEM CONNECTOR
System connector cable (Included)
Be sure to use the included system cable. The equipment may not operate if a cable other than the included one is used.
1
The names of the terminals given here are generally used names and may differ from set to set. Check in the operating instructions of the set to be connected.
5 ENGLISH
NOTE: Be sure to switch the communications mode before turning on the ASD-1R’s power. The communications mode will not switch if the MODE SELECT switch is operated while the power is on.
ENGLISH
Functions and operation When the ASD-1R and a device equipped with a DOCK CONTROL terminal are connected • By connecting the ASD-1R and a DENON audio device equipped with a DOCK CONTROL terminal, it is possible to display the iPod’s status on the connected audio device’s on-screen display or regular display section and operate the iPod. • For instructions on operations, see the operating instructions of the connected audio device. NOTE: • On some devices it is possible to adjust the iPod’s volume, but the volume output from the ASD-1R cannot be adjusted. • Be careful with the volume when adjusting the iPod’s volume while listening through headphones.
When the ASD-1R and a device equipped with a system control (SYSTEM CONNECTOR) terminal are connected • When the ASD-1R and a system device equipped with a system control (SYSTEM CONNECTOR) terminal are connected, the iPod can be operated with the cassette deck or CD recorder remote control buttons. • Operate according to the setting of the MODE SELECT switch on the ASD-1R’s bottom panel. Remote control unit operating mode
System device connection
Communications mode System remote selector (MODE SELECT) control unit function switch
TAPE
To operate the iPod in the cassette deck remote control mode
L
Set to “TAPE”.
Set to “TAPE”.
Set to “CD-R”.
Set to “CD-R”.
R PB
CD-R
To operate the iPod in the CD recorder remote control mode
L R PB
Button names may differ from set to set. Check in the operating instructions of the set to be connected. NOTE: • Note that DENON will accept no responsibility whatsoever for loss of or damage to iPod data when using an iPod connected to the ASD-1R.
6 ENGLISH
• Depending on the iPod’s software version, it may not be possible to operate the iPod with the ASD-1R. Use the latest software version. Check the Apple Computer website for information on the latest software version.
ENGLISH Functions and operation
Functions and operation
Remote control buttons and operations iPod function
Name of remote control button
Operation
TAPE
CD-R
Play
1 PLAY
1 PLAY
Starts playback.
Pause
1 PLAY
1 PLAY or 1/3
Pauses playback.
Stop
2 STOP
2 STOP
Stops playback.
Cue to next track
7
9
Skips playback to next track.
Cue to previous track
6
8
Skips playback to previous track.
Repeat
–
REPEAT (1/ALL)
Shuffle
–
RANDOM
Playlist search/ Album search
–
PROG./DIRECT
Cue to next playlist/album
–
7
When in the playlist search mode or album search mode, skips to the next playlist or album.
Cue to previous playlist/album
–
6
When in the playlist search mode or album search mode, skips to the previous playlist or album.
Switches the repeat mode. OFF → Single track repeat → All track repeat → OFF Switches the shuffle mode. OFF → Shuffle by track → Shuffle by album → OFF Switches the search mode.
Button names may differ from set to set. Check in the operating instructions of the set to be connected. Operate the iPod image functions on the iPod itself. NOTE: • Depending on the iPod model, some functions may not operate. • Some system devices may not be equipped with the above buttons. • With some system components, functions may not be operable even if there are corresponding buttons on the remote control unit.
7 ENGLISH
ENGLISH
Troubleshooting If a problem should arise, first check the following. 1. Are the connections correct? 2. Have you operated the receiver according to the Operating Instructions? If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. Disconnect the power immediately and contact your store of purchase. Symptom
Cause
Measures
• Check that the iPod is playing. • Check that the iPod is properly connected to the ASD-1R’s dock connector. • The AC adapter is not connected to the ASD-1R or a • Check the connections. power outlet. • Check the connections. • The AV/Control cable is not properly connected. • Set the monitor’s input selector to the proper position for • The monitor’s input selection is not properly set. the connected video input terminal. • The iPod is not playing. • The iPod is not properly connected to the ASD-1R.
No sound is produced. No image appears on the monitor.
Does not operate properly when a device equipped with a dock control terminal is connected
• The ASD-1R’s communications mode is not properly set.
– 4, 5 4, 5 4, 5 –
• Check that the communications mode is set to “DOCK CONTROL”. (Turn the power off when changing the setting.)
4
• Check that the communications mode is set to “TAPE” or “CD-R”. (Turn the power off when changing the setting.) • The communications mode is not suited for the AV/Control • Set the communications mode to match the AV/Control cable setting. cable connection. • The system remote control unit’s function selector is not • Match the communications mode and system remote control unit function. properly set. • You are using a cable other than the included system • Use the included system cable. cable.
5
• The ASD-1R’s communications mode is not properly set. Remote control unit does not operate properly when a device equipped with a SYSTEM CONNECTOR terminal is connected.
Page
8 ENGLISH
5, 6 6 6
ENGLISH
Specifications 2 iPod control dock (ASD-1R) Power supply: Power consumption: Maximum external dimensions: Mass: Terminal:
DC IN 12V (Dedicated AC adapter) 1.5 W (When iPod is disconnected) 104 (W) x 28.5 (H) x 76.5 (D) mm 220 g Analog audio output terminals x 1, S-Video output terminal x 1, Control terminal x 1
2 AC Adapter (KSAFD1200120W1UV) Rated current: Rated voltage:
100 – 240 V, 50/60 Hz 0.4 A
* For purposes of improvement, specifications and design are subject to change without notice.
9 ENGLISH
TOKYO, JAPAN www.denon.com
Denon Brand Company, D&M Holdings Inc. Printed in China 00D 511 4514 209
