Transcript
ITEM NO. PART NUMBER DESCRIPTION Vendor 1 ASQ-001 End Tube Clamp - Lower Printed 2 ASQ-002 End Tube Clamp - Upper Printed 3 ASQ-003 Modified Aluminum Straw ilikethatsticker.com 4 ASQ-004 Motor Mount Rev B Printed 5 DJI NAZA-M Lite Flight Controller getfpv.com 6 ASQ-005 Rubber Isolator Bulb ilikethatsticker.com 7 ASQ-006 Center Brace Printed 8 ASQ-007 Flight Controller Mount Plate Printed 9 ASQ-008 Upper Cover Printed 10 20A Q-Brain 4 in 1 Speed Controller hobbyking.com 11 ASQ-009 Lower Cover Printed 12 ASQ-010 Camera Lower Vibration Plate Printed 13 Fat Shark 600TVL Camera FPV Camera getfpv.com 14 ASQ-011 Camera Vibration Upper Plate Printed 15 ASQ-012 Fat Shark Camera Mount Printed 16 Power Board firefly Power Distribution Board ebay.com 17 Multistar Elite 2216-920 920Kv Brushless Motor hobbyking.com 18 8 Inch Prop CCW 8X4.5 Prop hobbyking.com 19 8 Inch Prop CW 8X4.5 Prop hobbyking.com 20 FRSKY L9R (user defined) Radio Receiver stoneblueairlines.com 21 94510A310 M3 Brass insert ilikethatsticker.com 22 92141A009 Motor Mount Washer ilikethatsticker.com 23 92005A128 M3 X 20mm Screw ilikethatsticker.com 24 99397A441 Plastic Screw 8mm Length ilikethatsticker.com 25 92005A116 M3 X 6mm Screw ilikethatsticker.com 26 NAZA M Lite LED Module USB Port ans Status Indicator Included with Naza 27 Naza M Lite Power Module Clean Power Module for Naza-M Included with Naza 28 92005A118 M3 X 8mm Screw ilikethatsticker.com 29 90576A102 M3 Lock Nut ilikethatsticker.com 30 TS5828 600mW 5_8 Video Transmitter 32 Channel Video TX stoneblueairlines.com DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
ASQ Bill of Materials
MATERIAL
DRAWN BY:
QTY. 2 2 4 4 1 7 2 1 1 1 1 1 1 1 1 1 4 2 2 1 21 8 21 4 8 1 1 4 4 1
FINISH
J. Colville
DRAWING DATE:
6-3-2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
18 17
19 3
19 4
9 17
17 4
4 3 17
18
4 DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED
ASQ Top Level BOM Callout
PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
23
25
23
25
4
A
25 DETAIL A SCALE 2 : 1
25
DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED
Motor Mount Top Side Detail
PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
B 21 26
22 22
21 DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED
Motor Mount Bottom Side Detail
PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
DETAIL B SCALE 2 : 1
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
6 6
C
14 6
D
#21 M3 Brass insert 15
13
Motor Mounts Attach In outside two holes
4X 24
DETAIL C SCALE 2 : 1
DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED
Camera Mount and Arm End Detail
PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
DETAIL D SCALE 1 : 1
12
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
4X
Use These holes to loop Zip Ties thru and Clamp the upper and lower covers to the Aluminum Straw
DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED
Clamping the Covers in place
PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
Secured into top cover with Velcro, 2 sided tape, or Velcro
20 30 2
27 23
5
Same Screws in Front and Back 23
1
23 11
2 10
23 23
DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
1
23
Top Cover Removed
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
3 DETAIL E SCALE 1 : 1
3
6X 23
E 3
6X 21 3 Same Operation for front and back
DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
End Clamp Assembly
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
Mount Filght Controller to #8 by using either Velcro or double side Tape
4X 6
Be sure it is centered and the arrow points forward
8
3
7 3
7
Secure to Aluminum Straw Using A Zip Tie Thru The Hole 4X
DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED
Flight Controller Stabilizer
PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
11
28 29 16 10 Power Distribution is optional depending on the needs of your system
Mount Speed Controller using Velcro, Double side tape, or Zip Ties
DRAWING OF
GEOMETRIC TOLERANCE SPECIFICATION UNLESS OTHERWISE SPECIFIED
Speed Controller and Power System
PERFECT FORM REQUIRED FOR FEATURE-OF-SIZE AT MMC. TRUE POSITION TOLERANCE AND RELATED DATUMS APPLY AT CONDITION OF SIZE INDICATED IN FEATURE CONTROL FRAME. OTHER GEOMETRIC TOLERANCE AND RELATED DATUMS APPLY RFS. SEPERATE TRUE POSITION CALLOUTS MAY BE GAGED SEPERATELY, REGARDLESS OF DATUM REF.
DIMENSIONS ARE IN INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED
X.XX 0.010 FRACTIONS 1/32 X.XXX 0.005 ANGLES 1/2 SURFACE FINISH 125 Ra
MATERIAL
FINISH
DRAWN BY: DRAWING DATE:
6/4/2015
SCALE PART NO.
1:3
DWG NO.
SIZE
A
SHEET
REV
