Transcript
STEP 8: ATTACH VESA TO MONITOR WITH SLIDER
M2 WEIGHT ADJUSTMENT Your monitor should move up and down easily
M/FLEX INSTALLATION HARDWARE
and should stay in place once adjusted. If it is difficult to adjust or moves without assistance, it is not properly counterbalanced.
a. Remove the two M6 x 10 mm countersunk screws from the VESA plate and separate the plate from the plastic tongue
M2 WEIGHT ADJUSTMENT (Monitor should not exceed 20 lbs.)
b. Use the two M6x10 mm countersunk screws to screw the plastic tongue onto the slider bracket (A)
B
1. Use Hex Key C to loosen the two side screws (C) on the dynamic arm’s joints. Then use
c. Use two M6x16 mm countersunk screws (supplied with Slider) to screw the slider rail to the VESA plate (B)
Hex Key B to loosen the two top screws (B) on the dynamic arm. A
2. Tighten the two side screws (C) to achieve the force needed to hold the monitor weight. After tightening the side screws to
d. Use the 4 screws provided with the VESA plate to attach the slider assembly to the monitor. If the mounting holes are recessed, use the plastic spacers and longer screws included with your VESA plate.
M8 Security Screw
M2 Security Screw
the desired amount, tighten the two top screws (B) firmly to hold the adjustment. Note: Do not overtighten the screws as it can damage the screw head or threads. 3. Move the monitor around to ensure that movement is
e. Lower the plastic tongue into the quick release slot on the ball joint until it clicks into place
smooth and the arm functions as desired. If required, repeat steps 1 and 2 (in order) to adjust the force as needed.
Adjust the angle of the monitor so that it is level, and tighten the three screws (C) on the monitor mount to hold it in place
M8 WEIGHT ADJUSTMENT (Monitor should not exceed 40 lbs.) 1.
C Hex Key A (2mm)
STEP 9: CABLE MANAGEMENT
Hex Key B (2.5mm)
Hex Key C (3mm)
Hex Key D (4mm)
2.
C
D
HSIMF0117
B
STEP 1: MOUNT POST TO CLAMP MOUNT ASSEMBLY
iv. Fully tighten Clamp Screw (D).
M8 Bracket
v. Proceed to Step 3.
a. Install Cable Management Clip in desired location.
a. Fully tighten screw to post.
b. Position B1 Bracket with Knob in desired location on Post and turn Knob to securely fasten to Post.
M/Flex
b. Install Top Cap
STEP 6: ATTACH VESA TO MONITOR WITHOUT SLIDER
B3
(B) B2
(A)
Note: Score marks on post are about 1” increments.
Note: Do not mount post to clamp if installing a bolt-through mount.
c. For B2 Bracket installation, remove B1 cover. Securely fasten B2 to B1 with screw (A). Install B2 cover
D
B1
d. For B3 Bracket installation, remove B2 cap, place B3 brack on top and insert set screws. (B)
STEP 2: ATTACH MOUNT TO WORK SURFACE
C
A
A
B
*If mounting space for 75 mm VESA bracket is inset into back of monitor, place the 4 plastic spacers (B) between VESA bracket and monitor and use the Extended VESA screws (C).
B
STEP 4 : ADDITION OF SECOND ROW OF MONITORS
ii. Proceed to Step 3.
a. Remove Top Cap from originally mounted post.
M/Flex
C
b. Attach 2nd Post to original Clamp mounted post.
A B
i.
B
Posts must be fully seated against each other.
M8
ii. Place Top Cap on top of 2nd Post.
M/Flex
M2
(Straight Link)
c. Repeat Installation Step 3. C
v. Proceed to Step 3.
ii. Proceed to Step 3.
STEP 3: CABLE MANAGEMENT AND BRACKET ASSEMBLY
STEP 7: ADJUSTMENTS
STEP 5: ATTACH ARM TO BRACKET AS NEEDED
C B3
M2 Bracket A
B
a. Install Cable Management Clip in desired location.
a. Remove set (A) screw from Bracket using 2.5 mm Hex Key.
B2
(B)
b. Position B1 Bracket with Knob in desired location on Post and turn Knob to securely fasten to Post.
B1
a. If needed, adjust tension screws (A) to hold monitor in desired position.
b. Insert arm into Bracket.
A
A
c. Re-insert Set Screw. A
Note: Score marks on post are about 1” increments.
(A)
M8
c. When attaching a second monitor use B2 bracket and install pan head screw (A) using 2.5 mm Hex Key. d. When attaching a third monitor use B3 bracket and install set screws (B) using 2.0 mm Hex Key.
b. If your configuration does not use dynamic arms the monitor height can be adjusted with the screw below the quick release.
e. Install necessary caps B1/B2 Cap (when B3 not present) or B3 Cap.
c.
Use a 4mm hex key to turn the adjustment screw (B) clockwise to lower a monitor and counter clockwise to raise it until all monitors are the same height.
M2
B
