Transcript
15-1103.fm Page 1 Thursday, July 15, 1999 10:23 AM
Cat. No.
15-1103
Audio/Video Distribution Amplifier make up to three copies of your favorite camcorder tapes at the same time.
Separate audio and video signals are more efficient than VHF signals and are less susceptible to noise and other interference. However, using an ordinary splitter for a video signal results in either poor picture quality or no picture at all. This Audio/Video Distribution Amplifier lets you split the video and stereo audio output signals from a VCR or other video source without loss. You can send the video and stereo audio signals to as many as three other VCRs or monitors. The amplifier also helps you maintain picture quality when driving up to three TV monitors from a computer equipped with separate audio and video output (composite video) jacks. And, when you connect to up to three VCRs, you can © 1997 Tandy Corporation. All Rights Reserved. RadioShack is a registered trademark used by Tandy Corporation.
15-1103.fm Page 2 Thursday, July 15, 1999 10:23 AM
Please read and keep all of the instructions and warnings contained in this Own-
er’s Manual, in the supplied “Safety Instructions” sheet, and on the product. Warning: To prevent fire or shock hazard, do not expose this amplifier to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case.
!
This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product.
2
15-1103.fm Page 3 Thursday, July 15, 1999 10:23 AM
MOUNTING
CONNECTIONS
You can mount the amplifier on a wall or baseboard near your VCR, computer, or TV monitor. Do not mount it on any other electronic device.
Use only shielded audio/video cables to make the input and output connections for your amplifier. Do not use ordinary audio cables because they are more susceptible to noise and other interference.
Drill a 1/16-inch hole at the mounting location and insert the supplied screw in the hole, leaving about 1/8 inch extended. Position the amplifier with the recess on its back over the screw head and slide it down so the head fits snugly in the slot.
Note: Always use the shortest possible cable length for all connections. Do not coil extra cable next to the amplifier. Your local RadioShack store sells several types of video cables. For short connections, use a 2-foot cable (Cat. No. 15-1538). For longer distances, choose either a 6-foot cable (Cat. No. 15-1535) or a 24-foot cable (Cat. No. 15-1539). To take advantage of the color-coded jacks on the amplifier, use the matching color-coded Stereo Audio/Video Cable (Cat. No. 15-1537).
(MONO INPUT)
For mono audio and computer connections, use the 24-foot audio/video cable (Cat. No. 15-1540), which also has color-coded plugs on each end. Caution: Do not connect a video cable to the amplifier without connecting the other end to either a source unit or another component.
3
15-1103.fm Page 4 Thursday, July 15, 1999 10:23 AM
4
15-1103.fm Page 5 Thursday, July 15, 1999 10:23 AM
Connecting Inputs 1. Connect the left and right audio output jacks on the source unit (VCR, video
Connecting Outputs
disc player, computer, satellite receiver or descrambler) to the corresponding AUDIO INPUT L/M and R jacks on the amplifier.
1. Connect the white and red AUDIO OUTPUT A jacks on the amplifier to the audio input of your VCR or your TV monitor.
Note: If your source unit has a monaural output, connect a single cable from the source to the AUDIO INPUT L/M jack on the amplifier.
Note: If the VCR or monitor is mono, use a single cable from the source to the amplifier’s left (white) audio output jack.
2. Connect the video output on the source unit to the yellow VIDEO INPUT jack on the amplifier.
2. Connect the yellow VIDEO OUTPUT A jack on the amplifier to the video input of your VCR or monitor. 3. Repeat steps 1 and 2 for additional units. Connect a second or third VCR or monitor to AUDIO and VIDEO OUTPUT jacks B and C.
5
15-1103.fm Page 6 Thursday, July 15, 1999 10:23 AM
Limited Ninety-Day Warranty This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack companyowned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you. In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period. This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack A Division of Tandy Corporation Fort Worth, Texas 76102 8/97
Printed in the USA
15-1103.fm Page 7 Thursday, July 15, 1999 10:23 AM
OPERATION
TROUBLESHOOTING
1. Plug the power cord into a standard AC outlet. The indicator lights to show that the amplifier is receiving power.
• If you have poor or no reception on all units connected to the output jacks, be sure that the power cord is plugged in and the power indicator is on.
Note: The unit uses very little electricity and can be left on all the time. If you plan to be away for an extended period, however, unplug the power cord.
• If you have poor or no reception on a single unit, check the connections to that unit. Exchange cables to see if you can locate either a defective cable or connector.
2. Turn on the device connected to the amplifier’s input jacks.
• If you have poor picture quality, be sure you are using video cables to make all connections.
3. Turn on the device or devices connected to the amplifier’s output jacks. Note: If an output is connected to a monitor, be sure the monitor is set to receive separate audio and video signals.
7
