Transcript
Datasheet MODEL 1068-1 CENTRIFUGE SYSTEM STANDARD SPECIFICATIONS G-Range: 0 to 100 G's at 22 inch (559 mm) radius Payload Capacity: 12 inch (305 mm) cube; 50 lbs (22.67 Kg) per end of arm Maximum G-lbs: 5,000 G-lbs Rate Range: 0-400 RPM Slip Rings: Standard package is 8 lines at 5A, shielded Display: Digital Readout with resolution of XXX.XX Control: Digital, closed loop controller with keypad Communication Interface: RS-232 Testing Radius: UUT location is adjustable within mounting platform, 1527 inches (381-686 mm) Axis Rate Accuracy: ±0.1% of operating rate (above 40 RPM). Stability: ±0.1% of operating rate (above 40 rpm). Zero Drift. Speed Indication Accuracy: 0.01% ± 0.02 RPM (includes meter and encoder error) Vibration Isolation: Less than 0.1 G from DC to 100 Hz Mounting Platform: 12 inch deep by 14.75 inch wide (305 x 375 mm) specimen mounting platform at each end of arm Drive System: 1 H.P. D.C. variable speed motor-SCR controller with armature feedback, current limit, and automatic circuit protection Power: 230 VAC, 50/60 Hz, single phase, 10A Dimensions: 59.2 W x 66.7 D x 47.3 H inches (1504 x 1694 x 1201 mm) Weight: 1000 lbs. (454 Kg) Other Standard Features: 6000 pulse per revolution encoder; Unbalance Sensor provides automatic machine shut down in event of unbalanced loads; Electrical Door Interlocks prevent enclosure from being opened while machine is in motion; leveling kit; Dynamic Braking System; Over-Under Speed Indicator.
MODEL 1068-1 OPTIONS
Additional slip ring lines IEEE-488 Communication Interface (replaces RS-232) Wireless camera viewing system. Fluid transfer joint Coaxial rotary joint Larger arms available Positionable platforms
This Centrifuge System was formerly manufactured by Trio Tech International and Genisco Technology Corporation Specifications subject to change without notice For special requirements or custom specifications, contact Ideal Aerosmith
Rev: F
East Grand Forks, MN USA | Grand Forks, ND USA | Pittsburgh, PA USA | Phoenix, AZ USA | Menlo Park, CA USA Ideal Aerosmith, Inc. | +1 218.773.2455 | E-mail:
[email protected] | www.ideal-aerosmith.com
Datasheet MODEL 1068-2 CENTRIFUGE SYSTEM STANDARD SPECIFICATIONS G-Range: 0 to 1000 G's at 10.5 inch (267 mm) radius Payload Capacity: 24 inch (610 mm) diameter; 8 inch (203 mm) height; 50 lbs. (22.7 Kg) Maximum G-lbs.: 5000 G-lbs Rate Range: 0-1900 RPM Tabletop size: 24 inch (610 mm) diameter standard Tabletop Face Runout: 0.003 inch TIR at 6 inch radius Stability: ±0.1% of operating rate (above 190 rpm). Zero Drift. Display: Digital readout with resolution of XXXX.X RPM Controller: Digital, closed loop speed control with keypad interface Communication Interface: RS-232 Axis Rate Accuracy: 0.1% of operating rate (above 190 RPM) Speed Indication Accuracy: 0.01% ± 0.1 RPM (includes meter and encoder error) Vibration Isolation: Less than 0.1 G from DC to 100 Hz Slip Rings: Standard package is 8 lines, 5A shielded Mounting Platform: 24 inch (610 mm) diameter aluminum turntable with 50 each ¼ -20 threaded holes arranged in a 3-inch equilateral triangular pattern. Drive System: 2 H.P. D.C. variable speed motor-SCR controller with armature feedback, current limit, and automatic circuit protection Power: 230 VAC, 50/60 Hz, single phase, 15A Dimensions: 28.5 W x 50.9 D x 41.4 H inches (724 x 1293 x 1052 mm) Weight: 600 lbs. (272 Kg) Other Standard Features: 6000 pulse per revolution encoder; Unbalance Sensor provides automatic machine shut down in event of unbalanced loads; Electric Door Interlocks prevent enclosure from being opened while tabletop is in motion; Leveling kit, Dynamic Braking System; Over-Under Speed Indicator.
MODEL 1068-2 OPTIONS
Additional slip ring lines IEEE-488 Communication Interface (replaces RS-232) Wireless camera viewing system Fluid Transfer Joint Coaxial Rotary Joint
This Centrifuge System was formerly manufactured by Trio Tech International and Genisco Technology Corporation Specifications subject to change without notice For special requirements or custom specifications, contact Ideal Aerosmith
Rev: G
East Grand Forks, MN USA | Grand Forks, ND USA | Pittsburgh, PA USA | Phoenix, AZ USA | Menlo Park, CA USA Ideal Aerosmith, Inc. | +1 218.773.2455 | E-mail:
[email protected] | www.ideal-aerosmith.com
Datasheet
MODEL 1221 CENTRIFUGE SYSTEM STANDARD SPECIFICATIONS G-Range: 0 to 250 G's at 25-inch radius Payload Capacity: 18 inch cube (457 mm), 200 lbs. (91 Kg) per arm Maximum G-lbs.: 20,000 G-lbs. Rate Range: 0-600 RPM Slip Rings: 54 lines at 2A per line and 10 lines at 5A per line Drive System: 15 H.P. D.C. motor Control: AERO 4000 Controller with centrifuge-specific GUI Testing radius: UUT location is adjustable within mounting platform, 15-33 inch radius (381-838 mm) Stability: ≤0.1% of operating rate above 60 rpm. Zero Drift. Speed Indication Accuracy: 0.01% ± 0.02 RPM (measured over 1 revolution) Mounting Platform: 18 inches x 18 inches horizontal platforms located at each end of the rotating arm Power: 230VAC, 3 phase, 60 Hz, 65 A (70 A service) Dimensions: Centrifuge:
73 in. diameter x 72 in. high (1854 x 1829 mm)
Console: 24 in. wide x 30 in. deep x 70 in. high (610 x 762 x 1778 mm) Drive isolation Transformer: 26 in. wide x 22 in. deep x 34.5 in. high (660 x 559 x 876 mm Approximate Weight: 3500 lbs (1588 Kg) Other Standard Features: Unbalance Sensor provides automatic machine shut down in event of unbalanced loads; Electrical door interlocks prevent enclosure from being opened while machine is in motion; Dynamic Braking System
MODEL 1221 OPTIONS: • • • • •
Custom slip ring configuration Wireless camera viewing system Fluid transfer joint Coaxial rotary joint Positionable platforms
This Centrifuge System was formerly manufactured by Trio Tech International and Genisco Technology Corporation For additional information or special requirements, contact Ideal Aerosmith. Specifications subject to change without notice. Please call for pricing.
Rev: F
East Grand Forks, MN USA | Grand Forks, ND USA | Pittsburgh, PA USA | Phoenix, AZ USA | Menlo Park, CA USA Ideal Aerosmith, Inc. | +1 218.773.2455 | E-mail:
[email protected] | www.ideal-aerosmith.com
Datasheet
MODEL 1231 CENTRIFUGE SYSTEM STANDARD SPECIFICATIONS G-Range: 0 to 200 G's at 44-inch (1118 mm) radius Payload Capacity: 24 inch cube, (610 mm); 200 lbs. (91 Kg) per arm Maximum G-lbs: 20,000 G-lbs Rate Range: 0-400 RPM Slip Rings: 54 lines at 2A per line and 10 lines at 5A per line Drive System: 15 H.P. D.C. motor Control: AERO 4000 Controller with centrifuge-specific GUI Testing radius: UUT location is adjustable within mounting platform, 30-54 inch radius (762-1372 mm) Stability: ≤0.1% of operating rate above 40 rpm. Zero drift. Speed Indication Accuracy: 0.01% ± 0.02 RPM (measured over 1 revolution) Mounting Platform: 24 inches x 24 inches horizontal platforms located at each end of the rotating arm Power: 230VAC, 3 phase, 60 Hz, 65 A (70 A service) Dimensions: Centrifuge: 122.2 in. wide x 121.2 in. deep x 78.6 in. high (3103 x 3078 x 1996 mm) Console: 24 inches wide x 30 inches deep x 70 inches high (610 x 762 x 1778 mm) Drive isolation Transformer: 26 in. wide x 22 in. deep x 34.5 in. high (660 x 559 x 876 mm) Approximate Centrifuge Weight: 6100 lbs. (2765 Kg) Other Standard Features: Unbalance Sensor provides automatic machine shut down in event of unbalanced loads; Electrical door interlocks prevent enclosure from being opened while machine is in motion; Dynamic Braking System
MODEL 1231 OPTIONS: • • • • •
Custom slip ring configuration Wireless camera viewing system Fluid transfer joint Coaxial rotary joint Positionable platforms
This Centrifuge System was formerly manufactured by Trio Tech International and Genisco Technology Corporation For additional information or special requirements, contact Ideal Aerosmith. Specifications subject to change without notice. Please call for pricing.
Rev: H
East Grand Forks, MN USA | Grand Forks, ND USA | Pittsburgh, PA USA | Phoenix, AZ USA | Menlo Park, CA USA Ideal Aerosmith, Inc. | +1 218.773.2455 | E-mail:
[email protected] | www.ideal-aerosmith.com
