Transcript
Setup Guide WARNING: Drum key can be pinched when adjusting clamps with drum key. Operate carefully. Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.
1
Check the include items
CYMBAL PADS BOX Cymbal Pad for Hi-Hat
HI-HAT PEDAL BOX Cymbal Pad for Crash(with Choke)
Cymbal Pad for Ride (Three Zone)
DRUM PADS BOX
DRUM MODULE BOX (Dual Zone)
ACCESSORIES BOX
KICK PEDAL BOX
Hi-Hat Holder
Drum Key
Pad Mount X 4
Drumsticks
Screw X 3
Connection Cable X 9
Owner’s Manual
Setup Guide
Foot Pedal Beater
AFI
AC Adaptor
STAND AND CYMBAL HOLDER BOX Center Pipe (1)
Right Cross Pipe
100
95
Center Pipe (2)
75
Left Cross Pipe 25
Cymbal Rod Clamp Pillar (L1)
Pillar (R1)
Pillar (M1)
aw_DD620BX_Setup Manual_G01_150923_with kick pedal 2015
9
23
11:30:39
Cymbal Holder(L)
Cymbal Holder (R)
5
0
2
Set Up the Stand
Left Cross Pipe
Wing Nut Center Pipe (2)
Pillar (L1)
1
Pillar (R1)
2
Pillar (M1)
3 Cymbal Rod Clamp Center Pipe (1) Wing Nut
Right Cross Pipe
4
5
1.Attach the Center Pipe (2) to the clamp on the Pillar (L1) & (R1) 2.Attach the Left Cross Pipe to the clamp on the Pillar (M1) 3.Attach the Left Cross Pipe to the clamp on the Pillar (L1) 4.Attach the Right Cross Pipe to the clamp on the Pillar (R1) & (M1) 5.Attach the Cymbal Rod clamp on the Pillar (L1) 6.Attach the Center Pipe (1) to the clamp on the Pillar (L1) & (R1)
6
Note: Loosen or tighten the screws on the clamp with drum key as shown partial enlargement. A djust the height of the Right Cross Pipe and Center Pipe (1) with Wing Nuts as needed.
Wing Nut 1
Wing Nut 2
Wing Nut 1
Wing Nut 2 100
95
7
7.Attach the pad mounts to the mount holders on the Center Pipe (1), Right Cross Pipe, and firmly tighten the respective wing nuts 1. Note: Loosen or tighten the wing nuts on the mount holder as shown partial enlargement. Move the mount holders as needed,and firmly tighten the respective wing nuts 2.
aw_DD620BX_Setup Manual_G01_150923_with kick pedal 2015
9
23
11:30:40
8
8.Insert the two cymbal holders into the holders on the Center Pipe (1) Clamp, attach the hi-hat holder to mount holders on the Cymbal Rod Clamp, and firmly tighten the respective wing nuts. Note: Loosen or tighten the wing nuts on the mount holder as shown partial enlargement.
75
25
5
0
3
Attach the Parts
Attach the Pads
1.Loosen the wing nuts on the drum pads. Tom1
Wing Nut
2.Attach the drum pads to the pad mounts, and firmly tighten the wing nuts on the drum pads.
Tom2
Wing Nut 1 Snare
Tom3
Wing Nut 1
Wing Nut 2
Attach the Cymbal Pads Crash Ride
1.Remove the wing nut and felt washer from the cymbal tilter. 2.Place the cymbal pad, felt washer, wing nut 3 assembly as shown, and tighten the wing nut 3 to obtain an appropriate amount of sway. 3.Adjust the cymbal pad position with the wing nut 4. Note: Put the cymbal on the cymbal adapter and locate the tap of the adapter in the slot of the cymbal bottom.
Wing Nut 3
Felt Washer
Hi-Hat Wing Nut 4
Cymbal Tilter
2
1
Attach the Drum Module
Attach the AFI Insert the AFI position as shown.
AFI AFI
100
95
1
2
3 75
1.Push the cable into the mount holder slot on Center Pipe (1) as shown. 2.Connect cable to the DB25 Jack on the back of drum module. 3.Attach the module to the mount holder on the Center Pipe (1) , and firmly tighten with the screws. Note: Adjust the drum module position by moving the mount holders as needed, and firmly tighten the relevant wing nut.
aw_DD620BX_Setup Manual_G01_150923_with kick pedal 2015
9
23
11:30:42
25
5
0
4
Connect the Pads to the Drum Module
Connection Procedure Make connections as shown in the illustration. Crash
Ride
Drum Module Ride
Crash Drum Module
AFI AFI
AFI
Hi-Hat
Tom1 Tom2
Hi-Hat
AFI
Hi-Hat Pedal
Tom3
Tom3
Snare
Tom1
Tom2 Tom3
Snare
Kick Pad HI-HAT Control Kick Pad
1.Place the kick on the floor in the center of the rack as shown. 2.Place the hi-hat pedal on the floor on your left side. 3.Connect the pads to the drum module with the marked cables. Are you ready? Let's enjoy playing it.
5
Folding Drum Rack
Unfolding Drum Rack
Folding Drum Rack
Wing Nut 1 Wing Nut 2
Wing Nut 2
Wing Nut 3
Wing Nut 1
Wing Nut 3
Wing Nut 4 Wing Nut 4
2 1 Crash
Ride
Drum Module HI-HAT AFI
AFI Tom1
Tom2
100 Snare
Tom3 95
3
1.Loosen the wing Nut 1 ~ 4,Pillar (M) in the direction of arrow to appropriate location 2.Clamp turn to position as shown in figure 2 , Complete the drum rack
4
5
75
Drum rack through five steps can be completed folding. 1.Adjust the snare position as shown in figure 1. 2.Loosen 4 wing nut as shown in figure 1, push pillar (M) in the direction of arrow to folde as shown in figure 2. 3.Push down Snare/TOM3 in the direction of arrow down to as shown in figure 3. 4.Turn back HI-HAT Cymbal in the arrow direction as shown in figure 3、4. 5.Push down TOM1/TOM2 in the direction of arrow down to as shown in figure 5,Drum rack be completed folding. DD620BX_G02
aw_DD620BX_Setup Manual_G01_150923_with kick pedal 2015
9
23
11:30:47
25
5
0
