Transcript
M407 E
06.12.NF.1
*M407EN01*
AZ-LED
LED Ring Illuminator
Instructions
The product is the special episcopic LED ring illuminator for the “MULTIZOOM AZ100” microscope. The illuminator features white LEDs arranged as a ring. It is attached on the tip of the objective for illuminating a specimen. The product can be attached to an objective of 0.5x or 1x magnification and is recommended for low reflectance specimens.
Configuration 4
2 6
0 C O N O R
8
T
1
L
0
O N
O F F
Illuminator
Adapter for the objective of 1x magnification
Power cord * Power supply * The power cord is changed depending on the local power supply specifications.
Directions for use Attachable objectives The product can be attached to the following objectives: AZ-Plan Apo 0.5x,
AZ-Plan Apo 1x
* The product cannot be attached to the objective of 2x, 4x, or 5x magnification (AZ-Plan Fluor 2x, AZ-Plan Apo 4x, AZ-Plan Fluor 5x).
Attaching an adapter (for the objective of 1x magnification) To use the illuminator with the objective of 1x magnification, attach the special adapter provided with the illuminator. 1. Fully loosen the thumbscrew (clamp screw) on the side of the illuminator.
Adapter
Fixing screw for the adapter (side)
Screw hole
Illuminator
Thumbscrew (clamp screw)
2. Align the screw hole of the adapter with the clamp screw of the illuminator and insert the adapter into the illuminator. 3. Tighten the fixing screw for the adapter on the opposite side of the thumbscrew (clamp screw) by using a hexagonal driver provided with the AZ100 Zoom Body.
1
AZ-LED
LED Ring Illuminator
Instructions
Directions for use (continued) Attaching the illuminator Attach the illuminator to the objective. For the objective of 0.5x, the illuminator is attached directly. For the objective of 1x magnification, use the adapter. (See the item above.) 1. Fully loosen the thumbscrew (clamp screw) on the side of the illuminator. 2. Be careful not to damage the objective. Attach the illuminator to the tip of the objective so that the LEDs are facing downward. 3. Fully raise the illuminator and fix it with the thumbscrew (clamp screw). The tip of the thumbscrew catches the groove of the objective and the illuminator is fixed.
Groove
Thumbscrew (clamp screw)
Illuminator (with adapter)
Connecting the power supply Connect the power supply to the illuminator. 1. Check the position and orientation of the connector on the side of the illuminator. 2. Connect the cord (DC power cord) fixed to the power supply. Draw the cord for your convenient route.
Connecting the power cord
2. Connect the power cord to the AC inlet on the power supply.
Power switch
Connector 6
8
4
C O N T R O L
10
0
N
2
O
F
F
O
1. Check that the power switch of the power supply is turned off.
DC power cord
Power supply
Connecting the power cord
3. Connect another end to the wall outlet.
Illumination control To turn on the illumination, turn on the power switch on the power supply. To turn off the illumination, turn off the power switch on the power supply.
4
6
2
Brightness control 8
0 CONTROL10
Brightness control ON
To adjust the brightness of the illumination, rotate the brightness control on the power supply (0 to 100%).
OFF
Power supply
2
Power switch
AZ-LED
LED Ring Illuminator
Instructions
Specifications Model name
AZ-LED
Light source
White LED (useful life is more than 20,000 hours)
Brightness control range
0% to 100% (brightness)
Packaged parts
Illuminator, adapter, power supply, and power cord
Dimensions (excluding protrusions)
Illuminator: Power supply:
ø100 x 26 mm (H) 60.6 mm (W) x 107 mm (D) x 32 mm (H)
Weight
Illuminator: Power supply:
160 g 150 g
Output ratings (power supply)
21 VDC and 200 mA
Input ratings (power supply)
100 to 240 VAC ±10% and 50/60 Hz, 10 VA
Electric shock protection class
Class 2
Power cord
For Japan: Use the special power cord, AZ-LED-PCD. For countries excluding Japan where the power supply is 100 to 120 VAC: Use the special power cord, AZ-LED-PCU. For countries where the power supply is 220 to 240 VAC: Use the special power cord, AZ-LED-PCE.
Operating conditions
Temperature: Humidity: Pollution Installation category: Altitude: Indoor
0 to +40°C 85% relative humidity maximum (no condensation) degree: degree 2 category II 2000 m maximum use only
Storage conditions
Temperature: Humidity:
0 to +60°C 90% relative humidity maximum (no condensation)
Safety standards compliance • CE marking • This product meets EU Low Voltage Directive requirements. • This product meets EU EMC Directive requirements. (EN61326) • Laser safety This product complies with IEC / EN60825-1 +A2: 2001 Class 1 requirements. (Class 1 LED Product) • This is the UL-listed product. • This product meets FCC Part 15B Class A requirements. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
• This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. (ICES-003 Class A) • This product complies with Australian EMC. (AS/NZS C1SPR11 Group1 Class B)
3
AZ-LED
LED Ring Illuminator
Instructions
Caution Although Nikon products are designed to provide the utmost safety during use, incorrect usage or failure to follow the safety instructions provided may cause personal injury or property damage. Damage or injury that may occur due to mishandling is unwarranted. To ensure correct usage, read the instruction manual carefully and thoroughly before using the product. Do not discard the manual; keep it handy for easy reference. Safety instructions within this manual are described with the symbols on the right to highlight their importance. For your safety, always follow the instructions accompanied by these symbols.
Symbol
Meaning
WARNING
Disregarding instructions accompanying this symbol may lead to serious injury or death.
CAUTION
Disregarding instructions accompanying this symbol may lead to injury or property damage.
WARNING Use of controls or adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. 1.
Intended application of the product: This product must be used only for microscopic observation. Do not use this product for other purpose.
2.
Do not disassemble: Disassembling this product may result in electric shocks or other hazards. Malfunctions and damage due to disassembling are unwarranted. Never attempt to disassemble any part other than the parts described in the instructions. If you experience problems with this product or the microscope system, contact your nearest Nikon representative.
3.
Read the instructions carefully: To ensure safety, carefully read this manual and the manuals provided with any other equipment used with this product. In particular, observe all warnings and cautions of each manual.
4.
Cautions about the power cord: Make sure to use the specified power cord for the AZ-LED. Using a wrong power cord may result in malfunctions or fire. For specifications of the power cord, refer to “Specifications.” To prevent an electric shock, turn off the power switch of the product whenever connecting or disconnecting the power cord.
CAUTION 1.
Handle with care: The product and the microscope system are precision optical instruments. Handle the product with care to avoid shock or impact. In particular, objectives may loose accuracy when exposed to even a weak physical shock.
2.
Do not wet the product or allow foreign matter to get inside: Never allow water to come into contact with the product because that may cause an electric shock or malfunction. Similarly, if foreign matter gets inside, an electric shock or malfunction may occur. If water or foreign matter enters the product, do not use the product but contact your nearest Nikon representative.
3. Turn off the power before assembling the product or connecting or disconnecting the cable: To prevent an electric shock and fire, turn off the power switch and disconnect the power cord from the wall outlet before assembling the product. 4.
Installation location: Being a precision optical instrument, the microscope may get damaged or loose accuracy if it is used or stored under unsuitable conditions. When selecting the installation location, note the following: • Avoid a brightly lit location, such as exposed to direct sunlight or directly under a room light. The image quality deteriorates if there is excessive ambient light. • Always install the microscope with a surrounding clear area of 10 cm or more. • Choose a location that is free from dust or dirt. • Choose a flat surface with little vibration. • Choose a sturdy desk or table that is able to bear the weight of the instrument. • Do not install the microscope in a hot or humid location. • Select a layout that allows easy removal of the power cord from the microscope’s AC inlet in the event of an emergency. • For details about the operating environment and storage environment, see “Specifications.”
5.
Weak electromagnetic waves: The product emits weak electromagnetic waves. Do not install the product near precision electronic devices to prevent degrading their performance. If a TV or radio reception is affected, move the TV or radio set farther from the product.
2-3, Marunouchi 3-chome, Chiyoda-ku, Tokyo 100-8331, Japan
4
