B-210-hdmatrix-recvr_manual - D

Transcript

SPECIFICATIONS Audio Output Up to Dolby Digital TrueHD / DTS Master Audio HDMI Support HDMI 1.3 Signal Rate 2.25 GBPS Input (2) RJ-45 / 3.5 mm IR Receiver Input Output HDMI HDCP Compliant YES Manual EQ Adjustment YES Power Supply 5VDC Power Consumption 2 Watts Troubleshooting Status and Power LED Video Output 1080p(24/60) / 1080i/ 720p /576p /480p /576i /480i CEC Support Yes Housing Metal Weight 1.4 lbs Dimensions 85mm (3.3”) x 92mm (3.6”) x 24mm (1”) Transmission Length 130 feet (CAT-5) / 160 feet (CAT-6) WARRANTY 2-Year Limited Warranty This Binary™ Product has a Two-Year Limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA). OWNER’S MANUAL >> B-210-HDMATRIX-RECVR Extender for HDMI Cables PACKAGE CONTENTS INSTALLATION INSTRUCTIONS 1. Test all associated equipment and cables in the system for proper operation. Turn off all power before proceeding. 2. Make sure the HDMI™ cables being used do not exceed 1.0M (3.28 ft) and are at least 26 AWG. Any length longer than this may cause intermittence issues. To ensure maximum performance, please use high quality HDMI™ cables capable of transmitting 1080p signals. 3. Determine the best placement of the unit based on how it will be incorporated into the system design. Leave enough room to reach the EQ adjustment after installation. 4. Make sure all CAT 5 or CAT 6 cables are properly terminated (EIA/TIA-568B is recommended). 5. Connect the HDMI™ cables. 6. Turn on all associated equipment, plug in the 5V DC power, and verify that the signal LEDs are illuminated. 7. If a flickering, blinking, or snowy image is seen, adjust the EQ dial to improve the cable signal. An EQ set to “9” stands for the strongest signal for longer cable lengths while “0” is for short cable lengths. Try adjusting the EQ from 0 to 9 until picture is clear. 8. Once you have a picture, adjust down to the lowest number setting that still has a picture. This will ensure you have reached the optimal setting. 9. (OPTIONAL) Plug in Episode IR receiver into the 3.5mm IR jack. • 5VDC Power Supply • 4 Rubber Feet • Drywall screws for mounting • Owner’s Manual REMOTE LOCATION IR RECEIVER The B-210-HDMATRIX-RECVR can transmit IR control signal back to the matrix when using an Episode® IR Receiver. The matrix will send the IR signal to the appropriate emitter cable to control the selected HDMI source device. DVD Player IR Emitter HDMI Cable IR EMITTER Cat 1 Cat 2 DC/12V SOURCE 1 HDMI CAT5/6 OUTPUT 1 RS232 Cat 1 Cat 2 IR EXT. HDMI CAT5/6 OUTPUT 2 SOURCE 2 INPUT 1 SOURCE 3 EDID Cat 1 Cat 2 Cat 1 Cat 2 SOURCE 4 INPUT 2 INPUT 3 HDMI INPUT 4 CAT5/6 OUTPUT 3 HDMI CAT5/6 OUTPUT 4 CAT 5/6 Cables TV EQ IR EMITTER Cat 1 Cat 2 DC/12V SOURCE 1 HDMI CAT5/6 OUTPUT 1 RS232 Cat 1 Cat 2 IR EXT. HDMI CAT5/6 OUTPUT 2 INPUT 1 SOURCE 2 SOURCE 3 INPUT 2 EDID INPUT 3 INPUT 4 HDMI OUT IR Receiver MIN IR INPUT MAX DISTANCE Cat 5e/6 cables HDMI Cable Remote Display Cat 1 Cat 2 Cat 1 Cat 2 SOURCE 4 HDMI CAT5/6 OUTPUT 3 HDMI CAT5/6 OUTPUT 4