Transcript
P
MACHINE CODE : B20440
PowerMaster Plus™400 MODEL F-400S Strip Nailer
PowerMaster Plus™400 IMPORTANT! DO NOT DESTROY Always refer to safety and maintenance manuals #405218 and #405219 for detailed information on this tool. It is the customers responsibility to have all operators and service personnel read and understand this information.
TOOL SCHEMATIC AND PARTS
B20440
3
2
1
20
4 21 5 22 6 7
23
76
8
46 47 48 49
9
50
24 75 51
25
10 500463
11
33 32 34 80
26 74
12
31 7 38 35 37
27
15
14
79
29
16
17 18 19
43 44
52 78
30
39
13
77
42 40 41
501039 GREY Single Shot Trigger Assy
ORANGE BUMP FIRE
501048
36
65
59 58 57
42 69 54 53
63
62
66 68 67
72 60 61 55
70 71 64 63 08-08-2009
MACHINE CODE B20440
PARTS LEGEND POWERMASTER PLUS F-400S, 500705 > ▲ 1 501686 > 2 501760 3 091873 4 092757 5 500707 * 6 500461 * 7 092042 8 500407 * 9 501001 10 406041
* *
*
* *
* * *
13 14
091208 401950
16 500454 17 095432 18 500453 19 402906 20 092971 21 500709 22 402011 23 500710 24 092235 25 501002 26 500866 27 501286 28 501023 29 501333 501334 30 501219 31 500516 32 404274 33 500525 34 091622 35 501010 36 402669 37 501009 38 501008 39 402668 *
1 1 4 4 1 1 2 1 1 1
T.H.S.C.S. 1/4 - 20 x 1/2" BRUSH SILENCER S.C.H.C.S. 1/4 -20 x 1/2" FLATWASHER CAP O-RING O-RING SPRING MAIN VALVE GASKET CAP RETAINING RING
1 O-RING 1 O-RING 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
POST O-RING BUMPER POST B.H.S.C.S. - 10-32 X 5/8" O-RING PISTON PISTON ASSEMBLY SEAL SLEEVE SLEEVE O-RING SLEEVE O-RING BUMPER HOUSING REMOVED LABEL HOUSING - LEFTSIDE LABEL HOUSING - RIGHTSIDE END CAP HOUSING B.H.S.C.S. - SPECIAL FLATWASHER LOCKNUT 5/16 - 24 REDUCING PIPE BUSHING TRIGGER PIN TRIGGER SPIROL PIN LEVER BOTTOM TRIP RETAINING RING
40 41 42 * 43 44 46 47 ▲ 48 49 50 51 52 53 54 55 > >
57 58 59 60 61 62 ▲ 63 64 65 66 67 68 69 70 ** 71 72 > 73 74 75 76 77 78 79 80
097748 097746 071297 092174 401958 500712 095417 009016 501006 501363 091618 500713 501491 500717 500531
1 1 3 1 1 1 4 4 1 1 1 1 1 1 1
SPRING VALVE PIN VALVE PIN ROLL PIN 1/8 X 1/8" O-RING VALVE BODY VALVE BODY NOSE 30 LOCK WASHER 5/16 S.H.C.S. 5/16-18 X 1" SPRING W.C.E. UPPER W.C.E. S.H.C.S.1/4-20 X 1/2" LOWER W.C.E. MAGAZINE WITH WEAR STRIPS NAIL COVER FOLLOWER
501606 501607 500848 501046 500513 500839 404904 500509 501028 501026 066840 404414 404325 500520 500458 500838 500199 500729 500779 500249 002187 404800 501039 501299
1 1 1 1 1 1 2 1 1 1 1 2 2 2 1 1 1 1 1 1 1 1 1 2
END CAP MAGAZINE-LF END CAP MAGAZINE-RT LATCH DRUM PIN ASSEMBLY NEGATOR ASSEMBLY NAMEPLATE SCREW 1/4 - 28 X 5/8" FRONT BRACKET SPRING LATCH S.H.C.S. 8/32 X 2" S.H.C.S. 8/32 X 3/4" FLATWASHER #8 STOP NUT WEAR STRIP WARNING LABEL LOGO LABEL REMOVED BLADE SEAL FLANGE SLEEVE O-RING SLEEVE LOCK WASHER FLAT WASHER SEQUENTIAL TRIGGER GREY S.H.C.S. 1/4-20 X 1"
Denotes Normal Wear Items
**
Make sure Warning Label (Part No. 500458) is properly affixed. Replace if necessary. Label available at no charge through the Service Department.
▲
Apply Loctite 242 (Blue) Part No. 093500
✎ >
Denotes New Change
WARNING All parts must be periodically inspected and replaced if worn or broken. Failure to do this can affect the tool’s operation and present a safety hazard.
Note: For optimum performance Paslode recommends the use of a 3/8” Male fitting.
08-08-2009
MACHINE CODE B20440
ACCESSORIES BUMP FIRE Kit This special attachment is designed for "contact" firing).
Part No.501048 Remote Fire Valve This valve via a positive air signal allows a machine mounted tool to be operated from an automatic air valve or foot pedal system.
Part No. 1X0713
Trigger Valve Kit Repairs trigger valve air leaks.
Part No. 219224
No-Mar Work Contacting Element W.C.E. with a rubber tip prevents you from marring wood surfaces.
Part No.500903
No-Mar Tip Replacement tip for No-Mar Work Contacting Element #500903.
Part No. 501022
Lubricant Part No. F27625
Lubricating Oil 16 oz.
Degreaser Cleaner Part No. B20544L
Ideal cleaner for all Paslode tools.
SAFETY INSTRUCTIONS
DO NOT EXCEED MAXIMUM RECOMMENDED AIR PRESSURE
WEAR EYE AND HEARING PROTECTION
60
0
120
60
120
0
Always wear hearing protection and eye protection devices, including side shields when operating or working in the vicinity of a tool.
Operate the tool using only the recommended air pressure. Do not exceed the maximum air pressure marked on the tool. Be sure the air pressure gauge is operating properly and check it at least twice a day.
Never use any bottled air or gases such as oxygen to operate the tool since they could cause the tool to explode.
P Printed in U.S.A. © 2003, Illinois Tool Works , Inc.
An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills 60061-3105
405680-8 03-08-2009
