Transcript
BAR A70
Q U I C K S TA R T G U I D E
THANK YOU FOR CHOOSING ORBITSOUND This guide is all you need to set up your ORBITSOUND BAR A70 to start enjoying natural and immersive room filling airSOUND™.
You can table or wall mount your soundbar with the included fixings. Please ensure the centre speakers and side airSOUND speakers are free from obstacles within 10cm to ensure the best sound.
airSOUND™ SPEAKERS NFC Tag
Centre Speakers
T O U C H PA N E L B U T T O N S Input Source Remote Control Learning Bluetooth (Hold to pair) Volume +
Remote Receiver
Display
Remote Learning Wireless Subwoofer Error/Pairing Volume/Bass/Treble Optical Source Bluetooth Source
Volume -
AUX Source
Power / Standby
Power/Mute
CONNECTING YOUR BAR A70 1) CONNECT POWER
2) CONNECT YOUR TV
NO OPTICAL ON TV?
Connect power to the rear of your soundbar (1) and subwoofer (2). Switch on the subwoofer power (3).
Connect your TV using the optical cable included, Make sure to remove the protective caps on each end of the cable before plugging the cable in. Connect the optical cable (4) to your TV and soundbar.
If your TV doesn’t have an optical socket, connect using the 3.5mm AUX cable supplied to the audio out of your TV and the AUX input (5) on the soundbar.
4 TV OPTICAL AUDIO OUT
3
Subwoofer Pairing: 1) Long Press subwoofer PAIR; STATUS will flash
5 1
1
2) Long Press soundbar Vol+ and Vol-
©2014 Orbitsound ltd.
2
3
4
2
1 CONNECTING BLUETOOTH
2
LEARNING TV REMOTE VOLUME
1
2
1
2
1
2 Pair with Device? NO
LIGHT: CONNECTED ToSOLID pairBLUE a Bluetooth device: Press and hold (3 seconds) FLASH BLUE LIGHT: CONNECTING MODE theSLOW Bluetooth button (1), the Bluetooth light (2) will flash FAST FLASH BLUE LIGHT: PAIRING MODE faster. Search for ‘Orbitsound A70’ on your device list and pair.
3 2
VOYANT BLEU: CONNECTÉ
LICHT: VERBONDEN NOTE: TapBLAUW the Bluetooth button (1) to disconnect LANGZAAM KNIPPEREN: METYou VERBINDEN or to reconnect your device BEZIG easily. can use the SNEL KNIPPEREN: VERBIND MODUS Play controls on the Orbitsound remote to control bluetooth audio playback. KONSTANT BLÅT LYS: TILSLUTTET
VOYANT BLEU CLIGNOTANT LENTEMENT: EN MODE CONNEXION
LANGSOMT BLINK: SØGER TIDLIGERE TILSLUTTET
VOYANT BLEU CLIGNOTANT RAPIDEMENT: CONNEXION ÉTABLIE
HURTIGT BLINK: SØGER NYE ENHEDER
D O E S Y O U R D E V I C E H AV E N F C LUZ ? AZUL FIJA: CONECTADO
LUZ AZUL FIJA: CONECTADO
PARPADEO LENTO LUZ AZUL: MODO CONEXIÓN
PARPADEO LENTO LUZ AZUL: MODO CONEXIÓN
PARPADEO RAPIDO LUZ AZUL: MODO EMPAREJAMIENTO
PARPADEO RAPIDO LUZ AZUL: MODO EMPAREJAMIENTO
BLAUES DAUERLICHT: VERBUNDEN
YHTÄJAKSOINEN VALO: YHDISTETTY
BLAUES BLICKLICHT (LANGSAM): ANSCHLUSS- MODUS
HIDAS VILKKUVALO: YHTEYDEN MUODOSTUS TILA
BLAUES BLINKLICHT (SCHNELL): PAIRING-MODUS
NOPEA VILKKUVALO: PARITUS TILA
4
Pair with Device? NO
YES
Press and hold (3 seconds) LRN (1) to learn from a new remote. Press Vol+ on new remote when prompted (2), wait, then repeat when prompted by the soundbar. Repeat for Vol- when prompted. The system will confirm successful remote learning (2) and flash all lights.
If it did not work no lights will flash, try again and use short presses on the new remote, and wait to be prompted for a press. Note: the BAR A70 can learn from many popular remotes. It is not compatible with all remote controls. Please refer to website for details.
PA I R I N G T H E S U B W O O F E R Subwoofer Pairing:
The subwoofer is factory paired. To re-pair a subwoofer: Press and hold (3 seconds) subwoofer PAIR button (1), the subwoofer pair light will flash. Press and hold Vol - and Vol+ (2) on the soundbar together. The SUB light
(3) will flash. The soundbar and subwoofer will connect. When the SUB light (3) lights without flashing, the system is paired.
2
1) Long Press subwoofer PAIR; STATUS will flash 2) Long Press soundbar Vol+ and Vol-
1
3
CONNECT WITH NFC:
TV OPTICAL AUDIO OUT
3
Subwoofer Pairing:
Use NFC to easily connect. Make sure Bluetooth and NFC are enabled on your device. Place your device’s NFC tag close to the NFC logo on the soundbar. You will be prompted to pair. 1) Long Press subwoofer PAIR; STATUS will flash
2
5
2) Long Press soundbar Vol+ and Vol-
1
4
©2014 Orbitsound ltd.
2
WALL MOUNTING
PROBLEMS? You may need to clear the Bluetooth memory if the subwoofer does not pair. Press and hold Bluetooth AND Source buttons for 3 seconds, then proceed to pair the subweoofer as above.
There is no sound from the subwoofer
1
Check that power to subwoofer is ON. Restart soundbar. If the with Device? wireless subwoofer error Pair light on NO YES the sound bar is solid red, please follow “pairing the subwoofer” instructions above.
CONNECTED
BLAUW LICHT: VERBONDEN
LIGHT: CONNECTING MODE
LANGZAAM KNIPPEREN: BEZIG MET VERBINDEN
IGHT: PAIRING MODE
SNEL KNIPPEREN: VERBIND MODUS
NNECTÉ
NOTANT LENTEMENT: EN MODE CONNEXION
3 2
NOTANT RAPIDEMENT: CONNEXION ÉTABLIE
NECTADO
UZ AZUL: MODO CONEXIÓN
T (SCHNELL): PAIRING-MODUS
LANGSOMT BLINK: SØGER TIDLIGERE TILSLUTTET HURTIGT BLINK: SØGER NYE ENHEDER
PARPADEO RAPIDO LUZ AZUL: MODO EMPAREJAMIENTO
HT: VERBUNDEN
T (LANGSAM): ANSCHLUSS- MODUS
TV
KONSTANT BLÅT LYS: TILSLUTTET
Ensure the wall is suitible for the wall plugs provided. LUZ AZUL Drill holes in your wallFIJA: as CONECTADO shown to fit the plugs and PARPADEO LENTO CONEXIÓN screws. Carefully hangLUZ theAZUL: A70MODO as shown.
LUZ AZUL: MODO EMPAREJAMIENTO
YHTÄJAKSOINEN VALO: YHDISTETTY
Master thickness
Subwoofer STATUS light: On: Connected and working. Flashing: Looking for soundbar. Off: Low power mode
F R E Q U E N T LY A S K E D Q U E S T I O N S
2
HIDAS VILKKUVALO: YHTEYDEN MUODOSTUS TILA NOPEA VILKKUVALO: PARITUS TILA
Recommended Soundbar Placement
2
YES
Cable clip
Cable access
4
Drill 2x6mm holes in wall, 644mm apart
IMPORTANT: WALL MOUNTING TO BE DONE ONLY BY AN EXPERIENCED PROFESSIONAL. ORBITSOUND ACCEPT NO LIABILITY FOR DAMAGE DUE TO IMPROPER OR UNSAFE WALL MOUNT INSTALLATION
No Sound from optical (TV) source, No Sound from optical Set-Top-Box (STB) source, Loud noise when watching HD channels on optical Please check your TV or STB settings. Make sure that the optical output format is set to ‘STEREO’ or ‘PCM’ format. This is the correct format for the sound bar. (Factory reset) I need to reset my settings Press and hold SRC and POWER on the soundbar for 3 seconds. All lights will flash to show a reset has happened. I cannot make my soundbar learn from my remote. When I complete learning process, no lights flash. Please note: Not all remotes are supported with our learning process. Check the website for
compatability information. If your remote should work but is not, make sure you are aiming the remote at the IR receiver (near the light panel). Make sure you tap the key on the remote to be learned once when shown to by the sound bar, and repeat when shown.
2
Switching from TV to Bluetooth, there is a big volume difference the TV is quiet. Some TVs reduce the volume of sound that comes out of the optical port. You will need higher volume settings on the soundbar to compensate. This is normal. How do I position my soundbar to get the best sound? Simply make sure that the side speakers are clear from obstacles. The subwoofer is wireless, but the best sound is achieved when the subwoofer is within 5m of the soundbar, and in the same general area. My remote control is not working Ensure the battery protection film has been removed. Pull the tab and remove.
The optical cable does not work
2
Please check the optical cable and remove any protective covers from connectors. Check the optical output format is PCM or STEREO on your source. I’m using Bluetooth and sometimes the sound is interrupted Bluetooth is a short range wireless technology. We recommend you keep your bluetooth device in the same room as the sound bar and not obstructed by walls or metallic objects as they can block the signal. Please do not place other wireless devices such as wireless routers, cordless telephones and microwave ovens close to your sound bar as they can interfere with the Bluetooth connection. I need more information Please visit www.orbitsound.com to download the full product user manual or contact a customer support representative. www.orbitsound.com/support ©2016 Orbitsound Ltd.
