Transcript
BARCO PROJECTION
72” REAR PROJECTION STRUCTURE FOR IQ R9842250
INSTALLATION MANUAL
06082003
R5976655/00
Barco nv Intelligent Displays Noordlaan 5, 8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.35.86.51 E-mail:
[email protected] Visit us at the web: www.barco.com
Printed in Belgium
Copyright © All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of BARCO.
Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufactures.
Table of contents
TABLE OF CONTENTS 1. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Package of the 72" rear structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Unpacking the 72" rear structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Mounting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1 3.2 3.3 3.4 3.5 3.6 3.7
Mounting the base assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Mounting the Top assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Base and top assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mounting the Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Mounting the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Preparing the screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Mounting the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
1
Table of contents
2
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
1. Safety
1. SAFETY
1.1 Safety instructions Some operations in this manual require two persons to be executed safely.
This frame is designed for use only with the Barco iQ series projectors. Use with other appliances may result in instability causing possible injury.
Follow the instructions thoroughly. Improper installation may result in serious personal injury
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3
1. Safety
4
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
2. Package of the 72" rear structure
2. PACKAGE OF THE 72" REAR STRUCTURE
2.1 Unpacking the 72" rear structure How to unpack the assembly 1. see procedure
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
5
2. Package of the 72" rear structure
6
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
3. MOUNTING INSTRUCTIONS Overview
A
B
C
D
E
F
Image 3-1
Figure
Description
Use
Page
A
hammer bolt + hexagonal nut
for all BVS profile fixations
page 7 page 9 page 10 page 13
B
M8 x 16 bolt and nut
- projector plate fixation
page 14
- projector fixation C
M8 x 25 bolt and nut
D
M6 x 20 bolt
E
screw + nut
frame fixation on the screen
F
screw
frame fixation
screen fixation
page 16
3.1 Mounting the base assembly Necessary tools nut runner
Necessary parts •
long bars (2x)
•
short bars (2x)
•
pre-mounted U-shaped assembly (2x)
•
pre-mounted assembly (1x)
•
hammer bolts and nuts (A)
How to mount the base assembly ? 1. Place the parts as shown on the image (image 3-2) See image 3-3. 2. Tighten the parts using the hammer bolts and nuts. 3. Mount the screen supporting parts using the hammer bolts and nuts.
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
7
3. Mounting instructions
Image 3-2
Image 3-3
8
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
3.2 Mounting the Top assembly Necessary tools nut runner
Necessary parts •
long bars (6x)
•
pre-mounted square parts
•
hammer bolts and nuts (A)
How to mount the top assembly ? 1. Place the parts as shown on the image (image 3-4) 2. Tighten the parts using the hammer bolts and nuts (image 3-5)
Image 3-4
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
9
3. Mounting instructions
Image 3-5
3.3 Base and top assembling How to mount the top assembly on the base assembly ? 1. Place the top assembly on the base assembly, place the mounting guides so as to be in front of the base assembly part. (image 3-6, image 3-7) 2. Tighten the parts using the hammer bolts and nuts (image 3-8)
10
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
Image 3-6
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
11
3. Mounting instructions
Image 3-7
Image 3-8
12
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
3.4 Mounting the Mirror Necessary tools nut runner
Necessary parts •
mirror
•
hammer bolts and nuts (A) To prevent risks of injury, the mounting of the mirror has to be done by 2 persons.
What has to be done ? The mirror has to be mounted on the assembly. This is done by means of three fixation points
STEP 1
STEP 2
Image 3-9
How to mount the mirror ? 1. Hook the mirror in the top assembly. Use the upper slot. (image 3-10) 2. Fix the bottom of the mirror to the transversal bar using a hammer bolt and nut (image 3-11)
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
13
3. Mounting instructions
Image 3-10
Image 3-11
3.5 Mounting the projector What has to be done ? The projector has to be mounted in the frame. Prior to that, the plate supporting the projector must be fixed. The plate is fixed at 2 positions: 1.
at the top by 2 pre-mounted fixation profiles
1.
at the bottom using 2 pre-mounted short bars and fixation profiles.
STEP 2
STEP 1
Image 3-12
The Projector itself is mounted on the plate using three bolts and nuts turned in the three projector feet
14
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions Necessary tools nut runner
Necessary parts •
projector support plate
•
bolts and nuts (B)
•
Barco iQ projector
•
Barco iQ projector feet
How to mount the projector plate ? 1. Fix the plate on the previously mounted short bars using the M8 bolts and nuts. (image 3-13) 2. Fix the plate on the upper fixation profiles using the M8 bolts and nuts (image 3-14)
Image 3-13 view of the bottom fixation of the projector support plate
A B
Image 3-14
previously mounted short bar bolt (B)
How to mount the projector ? 1. If necessary, remove plastic covers of the feet 2. If necessary, mount the 3 feet on the projector 3. Turn the 3 bolts in the feet 4. Place the projector on the plate by hooking the bolts in the three plate holes 5. Secure the position by tightening the bolts (image 3-15)
Image 3-15 projector mounted on the plate
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
15
3. Mounting instructions
3.6 Preparing the screen What has to be done ? A frame has to be mounted on the screen
How to mount the wooden frame onto the screen ? 1. mount the lateral plate on the screen using the screws and nuts (E) 2. Fix the lateral plates to the bottom plate using the screws (F) (image 3-16)
E
F Image 3-16
3.7 Mounting the screen What has to be done ? How to mount the screen ? 1. Place the screen as shown on the image, the bottom must be positioned on the previously mounted arms (A). (image 3-17) 2. Fix the bottom part by tightening the bolt (image 3-18) 3. Fix the upper part by using the M8 x 25 bolt (image 3-19)
16
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
Image 3-18
Image 3-17
Image 3-19 Zoom of the upper left corner of the screen
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
17
3. Mounting instructions
18
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
Index
INDEX A
P
assemblies 7 mounting 7 assembling 10 base and top 10
package
M mounting 7, 9, 13–14, 16 mirror 13 projector 14 screen 16 top assembly 9
5
S safety 3 screen 16 preparations
16
U unpacking 5 retro case 5
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
19
