Transcript
Line Doubler Kit for RCVDS 05
R9828280
RCVDS05 + Quad Decoder+Line Doubler
Description: This document provides information on the mounting of the Quad Decoder, the Decoder Interface module and the Line Doubler module in the RCVDS 05 and its action on the specified input signals. For other operational information, consult the Owner's Manual for the RCVDS 05 (order number R5975765). Note: If interference disturbs the projected image in the (S)-Video mode, replace the input module S-Video R762244 (discrete version) by the S-Video input module R7622445 (SMD version).
Art. No.: R5975906 Rev. 06 1
Installation Instructions
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
ATTENTION To use the Quad Decoder feature in the RCVDS05, an adapted communication software is required (see page 3) KIT R762709
KIT R762710
Line Doubler R7625625
Quad Decoder R7627455
Decoder interface R762705 10-wire Cable Z3484106
9-wire Cable Z348509
11-wire Cable Z3495112
Screw R360862
Spacer R367614
Spacer R367614
Parts Listing for the Kit R9828280
Parts Listing for the Kit R762709
ITEM NO.
DESCRIPTION
ITEM NO.
DESCRIPTION
R32861910
U_S RCVDS05
R593010 R593472 R593545 R593546 R5975896 R5975906
BAG PE 80X 120X0.06 WL BOXBLKAST 82X 55X 20 BAG ASTSH 203X 305 BAG ASTSH 152X 254 MAN SER EP51 RCVDS05DCOMB MAN SER EP51 RCVDS05L_DBL
1 1 2 1 1 1
R367614 R7625625 V3247535 Z348509 Z3495106 Z3495112
SPR L25 M 3 H 5 NBRNI UN LDB PJ53 *701 SPR L 1.5 D 3.1D 4.5 BRNI CD CT FTFT P 9 100 CD CT FTFT P10 120 CD CT FTFT P11 130
R762709 R762710
UN LDB EP51C RCVDS05 UN DEC EP51C RCVDS05 +INT
1 1
R804793
BOX509AST 300X300X 55 2NB
1
QUANTITY 310
1
QUANTITY 6 1 2 1 1 1
Parts listing for the Kit R762710 ITEM NO.
DESCRIPTION
R360862 R367614 R762705 R7627455
SCR Z$7985 M 3 X 8 STZY SPR L25 M 3 H 5 NBRNI UN INT EP51 RCVDS05 COMB UN DEC PJ53 *808S COMB_F
QUANTITY 7 3 1 1 2
Mounting Instructions
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
The projector communication software checks the presence of the Quad Decoder in the RCVDS 05 when an input source Video, S-Video or Component Video is selected. When the projector uses the adapted communication software (see table below), these input signal types are converted to RGB/S output signals. IR Remote Control Communication link
Input Sources
Video Projector LCD
RGB-S* RGsB* S-Video
RCVDS05 + Quad Decoder + LiDo
Component Video
Projector CRT
RGB-CS (32kHz)
* Video, S-Video and Component Video with separate Sync are converted into RGB-S Analog Signals. * Component Video with Sync on Y is converted into RGsB Analog Signals.
RGB-S/RGsB Input module for LIDO (R762807)
CRT Projector type
Software version**
LCD Projector type
Software version**
BARCOVISION 701 BARCODATA 701
not adapted not adapted
BARCODATA 5000 BARCODATA 8000
not adapted not adapted
BARCOGRAPHICS 801S BARCODATA 801S
from V5.30 on from V5.30 on
BARCOGRAPHICS 8100 BARCODATA 2100
adapted from release adapted from release
BARCODATA 1101 BARCOVISION 1600
not adapted not adapted
BARCODATA 3100 BARCODATA 3000
from (V1.07**) - V2.07 from V2.07
BARCOGRAPHICS 1208 BARCOGRAPHICS 1209
from V5.31 on from V5.31 on
BARCODATA 5100 BARCODATA 8100
from (V1.07**) - V2.07 from (V1.07**) - V2.07
BARCODATA 1109 BARCOVISION 1609
adapted from release adapted from release
BARCOGRAPHICS 808 BARCODATA 808
adapted from release adapted from release
** Soft V1.07 is made for the earlier type Pixel Map Processor part# R762471.
**Software version of the projector can be read on the 'Start Up' or 'Identification' on screen menu. 3
Software Overview
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Mechanical disassembly of the RCVDS 05 for internal mounting of the kit 1. Removing the top cover
screw
Remove the 8 screws (4 on the top and 2 on each side). Lift top cover clear of unit.
2. Removing the front panel (for software adaptation) Pull off the power button.
4
EPROM Replacement
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Remove the screws holding frontpanel to main frame, two on bottom (A) and one on each side (B) B
A
Remove the 6 screws holding control panel module to frontplate
Replace the EPROM IC3 by the one provided in the kit, if the existing software version is lower than 2.10. CHECK: if the TEXT button is pressed for a few seconds, the version of the installed software is shown on the front panel display.
EPROM IC3
Re-install control panel module and power button following the above steps in reverse succession. 5
EPROM Replacement
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Mechanical mounting of the Decoder Interface module Place the Decoder Interface module on the provided spacers (fig.1) on the main frame. Take care to line up the threaded holes of the spacers with the holes on the module (fig.2).
provided spacers
to be plugged in on Decoder Interface module
Fig.1 Secure the position of the Decoder Interface module by insertion of 3 spacers (A), 2 spacers (B) and two screws (C) as shown below (fig. 2).
B
B
C A
C Decoder Interface module
A
fig. 3
Fig.2 6
Mounting Instructions
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Interconnection Decoder Interface module, Power Supply and Module frame
Interconnection Module frame/Decoder Interface
Plug in the 3 provided wire cables on the Decoder Interface
to be plugged in on Decoder module
Interconnection Power Supply/Decoder Interface
Fig.4 Mounting the Decoder module Place the Decoder module on the 3 provided spacers (fig.4) on the Decoder Interface module. Take care to line up the threaded holes of the spacers with the holes on the module (fig.5). Secure the position of the Decoder module by insertion of 2 spacers (A) and one screw (C) as shown below (fig. 5).
B A C
fig. 3
A
C
Fig.5 7
Mounting Instructions
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Interconnection Decoder module and Decoder Interface module (Fig.4 & Fig.6)
Interconnection Decoder/ Decoder Interface
Fig.6
Mounting the Line Doubler module Place the Line Doubler module on the 4 provided spacers (fig.6) in the base. Take care to line up the threaded holes of the spacers with the holes on the module (fig.7). Secure the position of the Line Doubler module by insertion of 4 screws.
Line Doubler
Fig.7 8
Mounting Instructions
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Interconnection Line Doubler module and Decoder Interface module (Fig.8)
Fig.8
9
Mounting Instructions
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Mechanical re-assembly of the top cover Putting back the top cover Place the top cover on the unit and secure with 8 screws (4 on the top and 2 on each side). Attention: the front side of the top cover is provided with a notch. Ensure that the notch enclosed the front top bar when mounting the top cover (see illustration below)
screw
10
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Routed inputs through the Line Doubler R (32kHz) R
Video
Video/S-Video Input Module
Signal transfer
G (32kHz)
Video/S-Video to R, G, B, S (32 kHz)
B (32kHz)
Video G B
CS 32kHz)
S-Video
Output Module
H/CS
S-Video
V
RGB Analog Input Module Standard Sync
R
R
G/Gs
G/Gs Video
B
B
H/CS
Signal transfer
H/CS
V
RGB Analog Input Module Tri-Level Sync
V
R
R
G/G3s
Video G/G3s
B
B
H/C3S
Signal transfer
S-Video
Output Module
H/C3S
V
V
R (32kHz)
R-Y
Component Video Input Module Input signal = 15kHz with Sync on Y
S-Video
Output Module
R Y B-Y
Signal transfer
G (32kHz)
Decoding the Input signal to RGB + Line Doubling (32kHz)
B (32kHz)
Video
G B CS (32kHz)
Output Module
S-Video
H/CS V
Component Video Input Module Input signal >15kHz* or Input signal = 15kHz with sep. sync
R
R-Y
R G
Y Signal transfer B-Y S/3S
Decoding the Input signal to RGB Sync Separate
Video G/G3s
B B CS/3S
Output Module
S-Video
H/C3S V
* Tri-Level Signal
R (32kHz) R
LiDo Input Module
G/Gs B S
R Signal transfer RGBs/RGsB to RGB-S with Line Doubling**
G (32kHz)
G B (32kHz)
B
CS (32kHz)
Video
Output Module
S-Video
H/C3S V
** If Fh>15kHz: Signal transfer to RGB with Sync separate on the original frequency
11
Routed inputs through the Line Doubler
Date: 06/10/2000 R9828280
Line Doubler Kit for RCVDS 05
R9828280
Printed in Belgium
12
Date: 06/10/2000 R9828280
