Transcript
Industrial PC power supplies
BEA-640-B5
Extended
Extended
Operation
Operation
AC input
400 Watt
Improved vibration protection according to EN 60945 Conductor plate with coating Safety clip for power cord The power supply BEA-640-B5 has been optimized for use in maritime navigation and radio communication devices according to EN60945:2002. The robust power supply is designed for uninterrupted operation (24/7) and is built using only high quality components. The power cord is secured by means of a safety clip. Fan monitoring is ensured via a reliable tachometric signal.
Te c h n i c a l d a t a Input voltage Input frequency Input current Inrush current Efficiency Hold up time Power-Good-Signal Protection Insulation voltage Earth leakage current Temperature Derating MTBF Max. operating altitude Humidity Dimensions (W x D x H) Weight (net)
Article No. BEA-640-B5
Output voltage +3.3 V +5 V +12 V -12 V -5 V +5 Vsb
90…264 V AC, active PFC 47…63 Hz 7 A (115 V AC) / 3.5 A (230 V AC) 49 A (115 V AC) / 94 A (264 V AC) ≥75 %, 230 V AC / ≥70 %, 115 V AC (full load) >16 ms Switch on delay 100…500 ms Switch off delay 1 ms Short circuit protection: At every output, switch off / +5 Vsb, auto-recovery Overload protection: 110…150 %, switch off Overvoltage protection: +3.3 V (+3.9…+4.3 V), +5 V (+5.7…+6.5 V), +12 V (+13.6…+15 V) Input / Chassis 3100 V DC Input / Output 4242 V DC <3.5 mA, 115 V AC / 230 V AC Operating: -10…+70 °C / Storage: -20…+80 °C +50…+70 °C, 1 % / °C 177000 h according to MIL-HDBK-217F at 50 °C without fan 2000 m Operating: 10…85 % RH, non-condensing / Storage: 10…90 % RH, non-condensing 150 x 140 x 86 mm ±0.5 mm 2.1 kg
Output current min max 0 A 28 A 0.5 A 35 A 1 A 30 A 0 A 0.8 A 0 A 0.5 A 0A 2 A
Load regulation ±5 % ±5 % +7/-5 % ±5 % ±5 % ±5 %
Ripple & Noise 50 mV 50 mV 120 mV 150 mV 150 mV 50 mV
Max. output is 400 W, combined max. output current at +3.3 V and +5 V must not exceed 45 A. Ripple and Noise was measured by a 20 MHz bandwidth limited oscilloscope with connected 220 µF electrolytic capacitor and 0.1 µF ceramic capacitor at each output. During a cross regulation test we recommend to keep the channel with higher output load at 80 % of its max. power and the channel with lower output load at 20 % of its max. power. As a power component this PSU is for assembly purposes only and must not be operated in unassembled condition. The final assembly has to comply with the valid EMC and safety standards.
The specified voltage tolerance data are valid for performance data within the limit values.
Bicker Elektronik GmbH | 86609 Donauwörth | Germany Tel. +49 906 70595-0 |
[email protected] | www.bicker.de
Industrial PC power supplies Drawing BEA-640-B5 AC input Tolerance ±0.5mm
Cable harness BEA-640-B5 P4, 300 mm ATX/EPS, 350 mm 20+4 pin
Specification is subject to change without notice. Errors excepted. Status as at: 27.11.2015
HD, 250 mm HD, 200 mm
HD, 200 mm HD, 150 mm HD, 150 mm
YELLOW (+12V) YELLOW (+12V)
4 3
2 1
24 23 22 21 20 19 18 17 16 15 14 13
12 11 10 9 8 7 6 5 4 3 2 1
YELLOW (+12V) YELLOW (+12V)
BLACK RED RED RED WHITE BLACK BLACK BLACK GREEN BLACK BLUE ORANGE
4 3 2 1
(GND) (+5V) (+5V) (+5V) (–5V) (GND) (GND) (GND) (PSon) (GND) (-12V) (+3,3V)
RED BLACK BLACK YELLOW 4 3 2 1
4 3 2 1
4 3 2 1
HD, 200 mm HD, 150 mm HD, 150 mm
4 3 2 1
RED BLACK BLACK YELLOW 4 3 2 1
(+3,3V) (+12V1) (+12V1) (+5Vsb) (PG) (GND) (+5V) (GND) (+5V REMOTE SENSE) (+5V) (GND) (+3,3V) (+3,3V REMOTE SENSE) (+3,3V)
4 3 2 1
(GND) (+5V) (+5V) (+5V) (–5V) (GND) (GND) (GND) (PSon) (GND) (-12V) (+3,3V)
4 3 2 1
4 3 2 1
Fan signal, 580 mm
(GND) (GND)
12 11 10
ORANGE YELLOW YELLOW
7 6 5 4 3 2 1
BLACK RED BLACK RED RED BLACK ORANGE ORANGE ORANGE
(+3,3V) (+12V1) (+12V1) (+5Vsb) (PG) (GND) (+5V) (GND) (+5V REMOTE SENSE) (+5V) (GND) (+3,3V) (+3,3V REMOTE SENSE) (+3,3V)
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW
(+5V) (GND) (GND) (+12V)
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW 4 3 2 1
(+5V) (GND) (GND) (+12V)
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW
RED BLACK BLACK YELLOW 4 3 2 1
(+5V) (GND) (GND) (+12V)
BLACK BLACK
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW
4 3 2 1
(+5V) (GND) (GND) (+12V)
(+5V) (GND) (GND) (+12V)
19 18 17 16 15 14 13
RED BLACK BLACK YELLOW
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW
24 23 22
RED BLACK BLACK YELLOW
4 3 2 1
(+5V) (GND) (GND) (+12V)
2 1
PURPLE 21 Tolerance ±2098 mm GREY 20
4 3 2 1
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW
RED BLACK BLACK YELLOW 4 3 2 1
ORANGE YELLOW YELLOW PURPLE GREY BLACK RED BLACK RED RED BLACK ORANGE ORANGE ORANGE
BLACK RED RED RED WHITE BLACK BLACK BLACK GREEN BLACK BLUE ORANGE
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW 4 3 2 1
(GND) (GND)
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW
RED BLACK BLACK YELLOW
BLACK BLACK
4 3
(+5V) (GND) (GND) (+12V)
RED BLACK BLACK YELLOW
(+5V) (GND) (GND) (+12V)
BLACK N.C. WHITE
BLACK N.C. WHITE
Optional accessory For detailed information please visit our website www.bicker.de and refer to the article number. Article No. Description X1-132 Power cord with European IEC-60320-C13 connector Bicker Elektronik GmbH | 86609 Donauwörth | Germany Tel. +49 906 70595-0 |
[email protected] | www.bicker.de
