Benq Es500 Projector User Guide

Transcript

BenQ BenQ Projector Device Driver NetLinx API BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 1 1. XDD Information Device Details Device Type: Video Projector Manufacturer: BenQ Model(s): BenQ Projector Device Revision: 1.0.0 Support Communication Types: Serial Serial Connection Parameters: Physical Layer: RS-232 Baud Rate: 115200 Data bits: 8 Stop bits: 1 Parity: None Flow control: None File Name: BenQ_Video_Projector_BenQ_Projector_1.0.0.xdd Author's Email: [email protected] Default Device Warming Time: 0 seconds Default Device Cooling Time: 0 seconds The following are comments provided by the author of the XDD. MANUFACTURER'S URL (website and/or product manuals) SUPPORT CONTACT (name, email, phone) ACCESSORY PRODUCTS (mounting brackets, cables) SERIAL PORT SPECS (pinout) CONTROL USAGE HAND CONTROL MODEL NUMBER BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 2 2. Channel Information The following are NetLinx Channels supported by this Device Driver. " * " denotes channels provided by Duet2 base and not protocol provided in this Device Driver. Channel Port 9* 1 24 1 25 1 26* 1 27 1 28 1 44 1 45 1 46 1 47 1 48 1 49 1 142* 1 148 1 Description Function: Power State Momentary Function: Cycle power when channel is activated NetLinx Constant: POWER Function: Volume Description: Ramping Function: Volume is ramped up while channel is active NetLinx Constant: VOL_UP ON: Increment Volume by 1. OFF: Function: Volume Description: Ramping Function: Volume is ramped down while channel is active NetLinx Constant: VOL_DN ON: Decrement Volume by 1. OFF: Function: Mute Momentary Function: Cycle volume mute when channel is activated NetLinx Constant: VOL_MUTE Function: Power State Description: Momentary Function: Power is turned on when channel is activated NetLinx Constant: PWR_ON Function: Power State Description: Momentary Function: Power is turned off when channel is activated NetLinx Constant: PWR_OFF Function: Main Buttons Description: Momentary Function: Press menu button MENU_FUNC NetLinx Constant: MENU_FUNC Function: Navigation Buttons Description: Momentary Function: Move menu cursor UP NetLinx Constant: MENU_UP Function: Navigation Buttons Description: Momentary Function: Move menu cursor DOWN NetLinx Constant: MENU_DN Function: Navigation Buttons Description: Momentary Function: Move menu cursor LEFT NetLinx Constant: MENU_LT Function: Navigation Buttons Description: Momentary Function: Move menu cursor RIGHT NetLinx Constant: MENU_RT Function: Navigation Buttons Momentary Function: Select current menu item NetLinx Constant: MENU_SELECT Function: Aspect Ratio Momentary Function: Cycle aspect ratios when channel is activated Cycle Order: AUTO, REAL, 4:3, 16:9, 16:10 NetLinx Constant: ASPECT_RATIO Function: Brightness Description: Momentary Function: Brightness is incremented when channel is activated NetLinx Constant: BRIGHT_UP BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 3 149 1 150 1 151 1 152 1 153 1 154 1 155 1 196* 1 199 1 210* 1 211 1 251* 1 252* 1 253* 1 Function: Brightness Description: Momentary Function: Brightness is decremented when channel is activated NetLinx Constant: BRIGHT_DN Function: Color Description: Momentary Function: Color is incremented when channel is activated NetLinx Constant: COLOR_UP Function: Color Description: Momentary Function: Color is decremented when channel is activated NetLinx Constant: COLOR_DN Function: Contrast Description: Momentary Function: Contrast is incremented when channel is activated NetLinx Constant: CONTRAST_UP Function: Contrast Description: Momentary Function: Contrast is decremented when channel is activated NetLinx Constant: CONTRAST_DN Function: Sharpness Description: Momentary Function: Sharpness is incremented when channel is activated NetLinx Constant: SHARP_UP Function: Sharpness Description: Momentary Function: Sharpness is decremented when channel is activated NetLinx Constant: SHARP_DN Function: Input Source Momentary Function: Cycle input source when channel is activated Cycle Order: COMPUTER/YPBPR, COMPUTER2/YPBPR2, HDMI, VIDEO, S-VIDEO, NETWORK, USB_DISPLAY, USB_READER NetLinx Constant: SOURCE_CYCLE Function: Mute Description: Discrete Function: Volume mute is on while channel is active NetLinx Constant: VOL_MUTE_ON ON: ON OFF: OFF Function: Picture Mute Momentary Function: Cycle picture mute when channel is activated NetLinx Constant: PIC_MUTE Function: Picture Mute Description: Discrete Function: Picture Mute is on while channel is active NetLinx Constant: PIC_MUTE_ON ON: ON OFF: OFF Function: Power State Description: Communication is established with device while channel is on NetLinx Constant: MODULE_DEVICEONLINE ON: Communication online. OFF: Communication offline. Function: Power State Description: Module data is synchronized with device while channel is on NetLinx Constant: MODULE_DATA_INITIALIZED ON: Data initialized. OFF: Data not initialized. Function: Power State Description: Feedback: Indicates Power is starting up and cannot accept commands NetLinx Constant: POWER_STARTUP_FB ON: Device warming. OFF: Device done warming. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 4 254* 1 255* 1 Function: Power State Description: Feedback: Indicates Power is shutting down and cannot accept commands NetLinx Constant: POWER_SHUTDOWN_FB ON: Device cooling. OFF: Device done cooling. Function: Power State Description: Discrete Function: Power is on while channel is active NetLinx Constant: POWER_ON ON: Device ON. OFF: Device OFF. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 5 3. Level Information No Levels are supported by this Device Driver. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 6 4. Command Information The following are NetLinx Commands supported by this Device Driver. Functional Group Port SNAPI2 Command ?CUSTOMLIST Custom 1 Description: ?CUSTOMLIST Query for the list of supported custom commands. Responds with: CUSTOMLIST-[,] Where: is one of a comma separated list of the custom commands support by the module. Only valid for Driver Design Modules The Custom Commands supported by this XDD are as follows: Custom.picturemode.3D Custom.picturemode.Presentation Custom.Audiosourceselect.Audio-VideoS-video Custom.Audiosourceselect.QueryAudiopassthroght Custom.MicVolume.MicVol Custom.MicVolume.QueryMicVol Custom.MicVolume.MicVolCustom.picturemode.Querypicturemode Custom.Audiosourceselect.Audio-HDMI Custom.Audiosourceselect.Audio-computer2 Custom.picturemode.sRGB Custom.Audiosourceselect.Audio-computer1 Custom.Audiosourceselect.Audio-HDMI2 Custom.picturemode.Cinema Custom.Audiosourceselect.Audiopassthroughoff Custom.picturemode.Dynamic Custom.picturemode.User2 Custom.picturemode.User1 ?ASPECT Aspect Ratio 1 Description: ?ASPECT Query aspect ratio. Responds with: ASPECT- ?ASPECTRATIOCOUNT Aspect Ratio 1 Description: ?ASPECTRATIOCOUNT Query aspect ratio count. Responds with: ASPECTRATIOCOUNT- ?ASPECTRATIOPROPERTIES Aspect Ratio 1 Description: ?ASPECTRATIOPROPERTIES Query properties for all aspect ratios, one ASPECTRATIOPROPERTY response for each aspect ratio. ASPECTRATIOPROPERTY-,, ?ASPECTRATIOPROPERTY Aspect Ratio 1 Description: ?ASPECTRATIOPROPERTY- Query properties for single aspect ratio. Responds with: ASPECTRATIOPROPERTY-,, BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 7 Aspect Ratio 1 ASPECT-4:3 ASPECT-AUTO ASPECT-16:9 ASPECT-16:10 ASPECT-REAL Description: ASPECT- Set aspect ratio. ?COOLDOWN Power State 1 Description: ?COOLDOWN Query for shut down time. Responds with: COOLDOWN- Where: is in seconds ?WARMUP Power State 1 Description: ?WARMUP Query for start up time. Responds with: WARMUP- Where: is in seconds COOLDOWN Power State 1 Description: COOLDOWN- Set shut down time. Where: is in seconds COOLING Power State 1 Description: COOLING- Cooling down counter time. Where: is seconds remaining COUNTERNOTIFY Power State 1 Description: COUNTERNOTIFY- Turn power counter notification on or off. Where: is 1 or 0 WARMING Power State 1 Description: WARMING- Warming up counter time, is seconds remaining WARMUP Power State 1 Description: WARMUP- Set warm up time. Where: is in seconds ?INPUT Input Source 1 Description: ?INPUT Query for the current input. Responds with: INPUT- Where: is one of the values returned in the query ?INPUTLIST. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 8 ?INPUTCOUNT Input Source 1 Description: ?INPUTCOUNT Query for the number of inputs ?INPUTLISTCOUNT Input Source 1 Description: ?INPUTLISTCOUNT Query for the number of input groups. Responds with: INPUTLISTCOUNT- ?INPUTPROPERTIES Input Source 1 Description: ?INPUTPROPERTIES Query input properties. Responds with one INPUTPROPERTY response for each input: INPUTPROPERTY,,,,, Where: is a virtual input number between 1 and . is the integer value of the virtual input port on the device (mutually exclusive group) is the label on the device is the text shown on the device display. ?INPUTPROPERTY Input Source Input Source 1 1 Description: ?INPUTPROPERTY- Query input properties for single input. Where: is a virtual input number between 1 and Responds with: INPUTPROPERTY-,,,, is a virtual input number between 1 and is the integer value of the virtual input port on the device (mutually exclusive group). is the label on the device. is the text shown on the device display. INPUT-COMPUTER/YPBPR INPUT-COMPUTER2/YPBPR2 INPUT-HDMI INPUT-VIDEO INPUT-S-VIDEO INPUT-NETWORK INPUT-USB_DISPLAY INPUT-USB_READER Description: INPUT- Set the current input. LISTSET- Device 1 Description: LISTSET-,,[;,...] Command to create a PropertyList. Where: is the PropertyList name. is the property key. is the property value. LIST APIs are to be used for user defined property list, these APIs are not intended to be used for well known SNAPI properties. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 9 LISTSELECT- Device 1 Description: LISTSELECT-, Command to a PropertyList to select the element at index. Where: is the PropertyList name. is the one-based decimal ordinal value of a property in the list, or key name. LIST APIs are to be used for user defined property list, these APIs are not intended to be used for well known SNAPI properties. LISTNEXT- Device 1 Description: LISTNEXT- Command to iterate in a forward* direction to the PropertyList’s next selected element. *Forward means increasing ordinal value. Where: is the PropertyList name. LIST APIs are to be used for user defined property list, these APIs are not intended to be used for well known SNAPI properties. LISTPREV- Device 1 Description: LISTPREV- Command to iterate in a backward* direction to the PropertyList’s next selected element. *Backward means decreasing ordinal value. Where: is the PropertyList name. LIST APIs are to be used for user defined property list, these APIs are not intended to be used for well known SNAPI properties. ?LISTSELECT- Device 1 Description: ?LISTSELECT- Query to discover a PropertyList’s selected element. Where: is the PropertyList name. If is not recognized, no response. If no selected element, Responds with: LISTSELECT-,0 Where: is the PropertyList name. Otherwise: Responds with: LISTSELECT-,,, Where, is the PropertyList name. is the one-based decimal ordinal value of this property in the list. is the property key. is the property value. LIST APIs are to be used for user defined property list, these APIs are not intended to be used for well known SNAPI properties. ?LISTSIZE- Device 1 Description: ?LISTSIZE- Query to discover a PropertyList size. Where: is the PropertyList name. If is not recognized, no response; otherwise, Responds with: LISTSIZE-, Where: is the PropertyList name. is a decimal integer representing the size of the list. LIST APIs are to be used for user defined property list, these APIs are not intended to be used for well known SNAPI properties. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 10 ?LIST- Device 1 Description: ?LIST- Query to discover a PropertyList contents. Where: is the PropertyList name. If is not recognized, no response; otherwise, a series of NetLinx strings, one for each element in the PropertyList. Responds with: LIST-,,, Where: is the PropertyList name, is the one-based decimal ordinal value of this property in the list. is the property key. is the property value. LIST APIs are to be used for user defined property list, these APIs are not intended to be used for well known SNAPI properties. ?FWVERSION Device 1 Description: ?FWVERSION Query for the device firmware version, Responds with: FWVERSION- ?VERSION Device 1 Description: ?VERSION Query for the module version, Responds with: VERSION- ?DRIVERVERSION Device 1 Description: ?VERSION Query for the device driver version, Responds with: DRIVERVERSION- (Only valid for Driver Design Modules) DEBUG- Device 1 Description: DEBUG- Set the debug state. Where: is 1-4 for ERROR, WARNING, DEBUG, INFO ?DEBUG Device 1 Description: ?DEBUG Query the debug level, Responds with: DEBUG- Where: is 1-4 for ERROR, WARNING, DEBUG, INFO REINIT Device 1 Description: REINIT Reinitialize communication with the device Diagnostic_Mode- Device 1 Description: NOT FOUND ?PROPERTY-IP_Address Device 1 Description: ?PROPERTY-IP_Address Query the current value of IP address. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 11 PROPERTY-IP_Address, Device 1 Description: PROPERTY-IP_Address, or PROPERTY-IP_Address, Set the value of IP address. Where: is an IP address. is a host name. REINIT required to take affect. PROPERTY-Port, Device 1 Description: PROPERTY-Port, Set the value of the port number associated with the IP address. Where: is a port number. REINIT required to take affect. ?PROPERTY-Port Device 1 Description: ?PROPERTY-Port Query the current value of the port number. Associated with PROPERTY-IP_Address. PROPERTY-Baud_Rate, Device 1 Description: PROPERTY-Baud_Rate, Where: is a serial port baud rate. Set the value of the baud rate associated with the Serial port. REINIT required to take affect. ?PROPERTY-Baud_Rate Device 1 Description: ?PROPERTY-Baud_Rate Query the current value of the baud rate. Associated with the Serial port. ?PROPERTY-Device_ID Device 1 Description: ?PROPERTY-Device_ID Query the current value of the device id. If supported by the device this is the id of the end device. PROPERTY-Device_ID, Device 1 Description: PROPERTY-Device_ID, Set the current value of the . Where: is a new device ID. If supported by the device this is the id of the end device. REINIT required to take affect. PROPERTY-Poll_Time, Device 1 Description: PROPERTY-Poll_Time, Set the current value of the poll timer interval. Where: is expressed in milliseconds. Warning setting the interval lower than 10,000ms (10 seconds) is not recommended. REINIT is not required to take affect. ?PROPERTY-Poll_Time Device 1 Description: ?PROPERTY-Poll_Time Query the current value of the poll time interval. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 12 PROPERTY-Online_Timeout, Device 1 Description: PROPERTY-Online_Timeout, Set the current value of the online timeout interval. Where: is expressed in seconds. This interval is the maximum time the device will remain in the online state given that no communication has been received from the device. REINIT required to take affect. ?PROPERTY-Online_Timeout Device 1 Description: ?PROPERTY-Online_Timeout Query the current value of the online timeout interval. ?PROPERTY-Minimum_Command_Interval Device 1 Description: ?PROPERTY-Minimum_Command_Interval Query the current value of the Minimum Time Interval Between Command Messages (in milliseconds). This property is read-only. PASSTHRU- Device 1 Description: PASSTHRU- SendSend a message directly to the device. Where: is the data to send PASSBACK- Device 1 Description: NOT FOUND PROPERTY- Device 1 Description: PROPERTY-, Set the property to a value. Where: is the property name. is the property value. ?PROPERTY- Device 1 Description: ?PROPERTY- Query for the value of property. Responds with: PROPERTY-, BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 13 5. Custom Command Information The following are Custom NetLinx Commands supported by this Device Driver. Functional Group Port Command Command: Custom.Audiosourceselect.Audiopassthroughoff Description: No description provided. Command: Custom.Audiosourceselect.Audio-computer1 Description: No description provided. Command: Custom.Audiosourceselect.Audio-computer2 Description: No description provided. Command: Custom.Audiosourceselect.Audio-VideoS-video Description: No description provided. Command: Custom.Audiosourceselect.Audio-HDMI Description: No description provided. Command: Custom.Audiosourceselect.Audio-HDMI2 Audio source select 1 Description: No description provided. Command: Custom.Audiosourceselect.QueryAudiopassthroght Description: No description provided. Event: Custom.Audiosourceselect.ResponseAudiopassthroghtoff Description: No description provided. Event: Custom.Audiosourceselect.ResponseAudio-computer1 Description: No description provided. Event: Custom.Audiosourceselect.ResponseAudio-computer2 Description: No description provided. Event: Custom.Audiosourceselect.ResponseAudio-HDMI Description: No description provided. Event: Custom.Audiosourceselect.ResponseAudio-HDMI2 Description: No description provided. Event: Custom.Audiosourceselect.ResponseAudio-VideoS-video Description: No description provided. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 14 Command: Custom.MicVolume.MicVol Description: No description provided. Command: Custom.MicVolume.MicVolMic. Volume 1 Description: No description provided. Command: Custom.MicVolume.QueryMicVol Description: No description provided. Event: Custom.MicVolume.Responesmicvol Description: No description provided. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 15 Command: Custom.picturemode.Dynamic Description: No description provided. Command: Custom.picturemode.Presentation Description: No description provided. Command: Custom.picturemode.sRGB Description: No description provided. Command: Custom.picturemode.Cinema Description: No description provided. Command: Custom.picturemode.User1 Description: No description provided. Command: Custom.picturemode.User2 Description: No description provided. Command: Custom.picturemode.3D picture mode 1 Description: No description provided. Command: Custom.picturemode.Querypicturemode Description: No description provided. Event: Custom.picturemode.Respones3Dmode Description: No description provided. Event: Custom.picturemode.ResponesCinema Description: No description provided. Event: Custom.picturemode.ResponesPresentation Description: No description provided. Event: Custom.picturemode.ResponessRGB Description: No description provided. Event: Custom.picturemode.ResponesUser1 Description: No description provided. Event: Custom.picturemode.ResponesUser2 Description: No description provided. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 16 6. HAS Properties Information The following NetLinx HAS Properties are supported by this Device Driver. Port 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Satisfied ?PROPERTY-Command-Holdoff ?PROPERTY-Has-Aspect-Ratio ?PROPERTY-Has-Aspect-Ratio-Cycle ?PROPERTY-Has-Auto-Focus ?PROPERTY-Has-Auto-Focus-Cycle ?PROPERTY-Has-Auto-Iris ?PROPERTY-Has-Auto-Iris-Cycle ?PROPERTY-Has-Brightness ?PROPERTY-Has-Color ?PROPERTY-Has-Contrast ?PROPERTY-Has-Custom ?PROPERTY-Has-Filter ?PROPERTY-Has-Focus ?PROPERTY-Has-Focus-Ramp ?PROPERTY-Has-Focus-Speed ?PROPERTY-Has-Freeze ?PROPERTY-Has-Freeze-Cycle ?PROPERTY-Has-Input-Select ?PROPERTY-Has-Input-Select-Cycle ?PROPERTY-Has-Iris ?PROPERTY-Has-Iris-Ramp ?PROPERTY-Has-Iris-Speed ?PROPERTY-Has-Lamp ?PROPERTY-Has-Menu ?PROPERTY-Has-Menu-10Key ?PROPERTY-Has-Menu-Navigate ?PROPERTY-Has-PIP ?PROPERTY-Has-PIP-Cycle ?PROPERTY-Has-PIP-Position-Cycle ?PROPERTY-Has-Picture-Mute ?PROPERTY-Has-Picture-Mute-Cycle ?PROPERTY-Has-Power ?PROPERTY-Has-Power-Cycle ?PROPERTY-Has-Sharpness ?PROPERTY-Has-Tint ?PROPERTY-Has-Volume ?PROPERTY-Has-Volume-Mute-Cycle ?PROPERTY-Has-Volume-Ramp ?PROPERTY-Has-Zoom ?PROPERTY-Has-Zoom-Ramp ?PROPERTY-Has-Zoom-Speed BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 HAS Property Query FALSE TRUE TRUE FALSE FALSE FALSE FALSE FALSE FALSE FALSE TRUE FALSE FALSE FALSE FALSE FALSE FALSE TRUE TRUE FALSE FALSE FALSE FALSE TRUE FALSE TRUE FALSE FALSE FALSE TRUE TRUE TRUE TRUE FALSE FALSE FALSE TRUE TRUE FALSE FALSE FALSE Page 17 7. Properties Information The following NetLinx Properties are supported by this Device Driver. Port Property Query 1 ?PROPERTY-Custom-List 1 1 ?PROPERTY-Lamp-Count ?PROPERTY-Menu-List 1 ?PROPERTY-Menu-Navigate-List 1 ?PROPERTY-PRESETCOUNT BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals Value Custom.Audiosourceselect.Audio-HDMI Custom.Audiosourceselect.Audio-HDMI2 Custom.Audiosourceselect.Audio-VideoS-video Custom.Audiosourceselect.Audio-computer1 Custom.Audiosourceselect.Audio-computer2 Custom.Audiosourceselect.Audiopassthroughoff Custom.Audiosourceselect.QueryAudiopassthroght Custom.MicVolume.MicVol Custom.MicVolume.MicVolCustom.MicVolume.QueryMicVol Custom.picturemode.3D Custom.picturemode.Cinema Custom.picturemode.Dynamic Custom.picturemode.Presentation Custom.picturemode.Querypicturemode Custom.picturemode.User1 Custom.picturemode.User2 Custom.picturemode.sRGB 1 MENU DOWN LEFT RIGHT UP 0 AMX LLC © 2015 Page 18 8. Sample NetLinx Code The following is sample NetLinx code. PROGRAM_NAME='Main' (***********************************************************) (***********************************************************) (* System Type : NetLinx *) (***********************************************************) (***********************************************************) (* DEVICE NUMBER DEFINITIONS GO BELOW *) (***********************************************************) DEFINE_DEVICE dvSerialPort = 5001:1:0 dvIpPort = 0:4:0 vdvMyDevice = 41001:1:0 (***********************************************************) (* CONSTANT DEFINITIONS GO BELOW *) (***********************************************************) DEFINE_CONSTANT (***********************************************************) (* DATA TYPE DEFINITIONS GO BELOW *) (***********************************************************) DEFINE_TYPE (***********************************************************) (* VARIABLE DEFINITIONS GO BELOW *) (***********************************************************) DEFINE_VARIABLE CHAR MyXDDFile[] = 'BenQ_Video_Projector_BenQ_Projector_1.0.0.xdd' (***********************************************************) (* LATCHING DEFINITIONS GO BELOW *) (***********************************************************) DEFINE_LATCHING (***********************************************************) (* MUTUALLY EXCLUSIVE DEFINITIONS GO BELOW *) (***********************************************************) DEFINE_MUTUALLY_EXCLUSIVE (***********************************************************) (* SUBROUTINE/FUNCTION DEFINITIONS GO BELOW *) (***********************************************************) (* EXAMPLE: DEFINE_FUNCTION () *) (* EXAMPLE: DEFINE_CALL '' () *) (***********************************************************) (* STARTUP CODE GOES BELOW *) (***********************************************************) DEFINE_START DEFINE_MODULE 'DeviceDriverEngine' MyDevice(vdvMyDevice, dvSerialPort, MyXDDFile) (***********************************************************) (* THE EVENTS GO BELOW *) (***********************************************************) DEFINE_EVENT (***********************************************************) (* THE ACTUAL PROGRAM GOES BELOW *) (***********************************************************) DEFINE_PROGRAM (***********************************************************) (* END OF PROGRAM *) (* DO NOT PUT ANY CODE BELOW THIS COMMENT *) (***********************************************************) BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 19 File was created Fri Jan 23 10:51:01 CST 2015 End of Document. BenQ BenQ Projector Downloaded from ProjectorsManual.com Manuals AMX LLC © 2015 Page 20