Transcript
BenQ PROJECTOR CEILING MOUNT GUIDE
SAFETY INSTRUCTIONS 1.
Follow the instructions in this menu when installing the projector with this bracket. Improper or inadequate installation could cause the projector to fall and injure someone.
2.
Make sure the installation is secure enough to bear the weight of all the devices, and also is secure enough to withstand the vibration.
3.
Use only the parts provide with the bracket, and any parts (commercially available) that are specified in this manual.
4.
Do not modify the bracket or the parts provided with the bracket.
5.
Do not use damaged parts. If any parts become damaged, contact your dealer.
6.
All bolts and screws must be tightened securely.
7.
Make sure not to block any ventilation openings when installing the projector.
8.
Do not install the projector in a location that is subject to high levels of dust or humidity.
9.
Do not install the projector in a location that is exposed to direct sunlight or in a location that is subject to extreme fluctuations in temperature (such as near an air conditioner).
10.
Clean only with a dry cloth.
11.
Special techniques and experience are required when installing the projector with this bracket. Contact your dealer to install the projector for you.
12.
Once the projector is installed, safety checks should be conducted on a regular basis.
TABLE OF CONTENTS Packing Parts List.................................................................................................................................................................... 2 Projector Installation and Throw Distance Chart ............................................................................................................ 3 Install the Projector with Ceiling Bracket.......................................................................................................................... 4 Adjust the Ceiling Bracket .................................................................................................................................................... 7 Specifications and Drawing ................................................................................................................................................... 9
BenQ Projector Ceiling Mount Guide
PACKING PARTS LIST ✓
CEILING ADAPTER
✓
U-PLATE
✓
TUBE
✓
PIPE
✓
PIPE-BASE
✓
H – ADJUST ADAPTER
✓
PROJECTOR ADAPTER
✓
V – ADJUST BOLT
✓
NUT x 7
✓
WASHER x 1
✓
M4 SCREW x 10
✓
BOLT x 6 (TUBE BOLT x 2 , L – ADJUST BOLT x 2 , PIPE BOLT x 2 )
Names of Parts
U - PLATE CEILING ADAPTER
TUBE TUBE BOLT x 2
L-ADJUST BOLT x 2
PIPE
PIPE BOLT x 2
H - ADJUST ADAPTER V – ADJUST BOLT
PIPE BASE PROJECTOR ADAPTER
2 Pack Parts List
BenQ Projector Ceiling Mount Guide
PROJECTOR INSTALLATION AND THROW DISTANCE CHART Throw Distance Chart Diagonal (in) 30 40 50 60 70 80 90 100 125 150 175 200 225 250 275 300 Diagonal (in)
4: 3 Aspect Ratio Screen Screen Width Screen Height Min Throw (cm) (cm) Distance (cm) 61 46 99 81 61 131 102 76 164 122 91 197 142 106 230 162 122 263 183 137 296 203 152 328 254 190 411 305 228 493 355 266 575 406 304 657 457 342 739 508 380 821 558 418 903 609 456 1000 Screen Width Screen Height MinThrow (cm) Distance (cm) (SW x 1.618)
Max Throw Distance (cm) 120 160 200 241 281 321 361 401 501 601 702 802 902 1002 1103 1203 Max Throw Distance (cm) (SW x 1.975)
Ceiling Throw Distance
Throw Distance
Projector Installation and Throw Distance Chart 3
BenQ Projector Ceiling Mount Guide
INSTALL THE PROJECTOR WITH CEILING BRACKET Overview ■
■
Whole set diagram
Ceiling Mount Device
Installation Procedure Insert U-PLATE into CEILING ADAPTER, and tighten 2 M4 screws (from the bottom) into
STEP A
the screw holes. Then mount the top part to the wall. U-PLATE CEILING ADAPTER
M4 screws
Ceiling mount screws (These are not included)
4 Install the Projector with Ceiling Bracket
BenQ Projector Ceiling Mount Guide
STEP B
Install the TUBE and the U-PLATE with 2 sets of bolt & nut (TUBE BOLT). NUT x 2
TUBE BOLT x 2
TUBE
STEP C
Install the PIPE and the TUBE with 2 sets of bolt & nut (L-ADJUST BOLT).
NUT x 2 L-ADJUST BOLT x2 PIPE
STEP D
Install the base-assembly.
STEP D1 Install the PIPE-BASE to H-ADJUST
STEP D2 Combine V-ADJUST ADAPTER and
ADAPTER with 2 M4 screws.
PROJECTOR ADAPTER with one set of V-ADJUST BOLT & WASHER & NUT. Then tighten the M4 screws on both sides.
M4 screw H-ADJUST ADAPTER
NUT M4 screw
WASHER V-ADJUST ADAPTER
M4 screw PIPE-BASE
V-ADJUST BOLT
Install the Projector with Ceiling Bracket 5
BenQ Projector Ceiling Mount Guide
STEP E
Assemble BASS-ASSEMBLY & PROJECTOR set.
STEP E2 Assembly
STEP E1 Sliding
STEP F
Assemble BASE-ASSEMBLY and ceiling mount device with 2 sets of bolt & nut (PIPE BOLT). Two persons are required for the completion of this step.
Ceiling mount device
NUT BASE-ASSEMBLY
PIPE BOLT
Installation finished.
6 Adjust the Ceiling Bracket
BenQ Projector Ceiling Mount Guide
ADJUST THE CEILING BRACKET Height Adjustment 1.
Make sure to un-install the projector first.
2.
Loosen the 2 sets of nuts connecting to L-ADJUST BOLT.
3.
Remove the L-ADJUST BOLT from the PIPE.
4.
Determine the correct position in accordance with the height of the screen. The height adjustment ranges between 225mm and 555mm ~ 765mm with a unit of 30 mm.
5.
Insert back the L-ADJUST BOLT into PIPE, and then tighten the previous 2 sets of nuts.
Maximum Height (non-adjustable)
Minimum Height (non-adjustable)
Install the Projector with Ceiling Bracket 7
BenQ Projector Ceiling Mount Guide
Horizontal Angle Adjustment 1.
Loosen the 2 sets of screws which are connecting PIPE-BASE and H-ADJUST ADAPTER.
2.
Determine the correct horizontal angle in accordance with the direction of the screen.
3.
Tighten the previous 2 sets of screws which are connecting PIPE-BASE and ADJUSTING ADAPTER.
4.
The total swivel angle is +/-30 degrees.
Vertical Angle Adjustment 1.
Loosen the 2 sets of screws which are connecting H-ADJUST ADAPTER and PROJECTOR ADAPTER.
2.
Determine the correct vertical angle in accordance with the direction of the screen.
3.
Tighten the previous 2 sets of screws which are connecting H-ADJUST ADAPTER and PROJECTOR ADAPTER.
4.
The total tilt angle adjustment is –5~+15 degrees.
8 Specifications and Drawing
BenQ Projector Ceiling Mount Guide
SPECIFICATIONS AND DRAWING Specifications Adjustment Range Height
225mm, 555mm, 585mm, 615mm, 645mm, 675mm, 705mm, 735mm and 765mm.
Horizontal angle –30 ~ +30 degrees Vertical angle
-5 ~ +15 degrees
Weight
3 kgw
Loading
4 kgw
Drawing ■
Left View
■
Front view
■
Right view
Install the Projector with Ceiling Bracket 9
