Transcript
USAI
®
Lighting
BeveLED Basic Dimming Compatibility ®
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D2 / DIML2
®
USAI Lighting
DIMMING DRIVER WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D2 / DIML2 LED: 0-10V Dimming Driver Wiring (Dims down to 10%)
Manufacturer 120V / 277V Crestron Crestron Crestron Crestron Crestron Leviton Lightolier (Philips) Lutron
Product
D2 / DIML2 Dimmer Compatibility Chart Dimmed Light Part Number Output Range
iLux dimmer expansion module DIN Rail dimmer DIN Rail analog output module 8 Channel dimmer module 8 Channel dimmer module IllumaTech dimmer Vega Diva
CLS-EXP-DIMFLV DIN-4DIMFLV4 DIN-A08 GLX-DIMFLV8 GLXP-DIMFLV8 IP710-DLX V2000FAMU DVTV-XX
Qty Fixtures Per Dimmer* Use source current per fixture specification sheet to determine number of fixtures per dimmer. Max number of fixtures is limited by dimmer load rating.
100% - 10% 100% - 10% 100% - 10% 100% - 10% 100% - 10% 100% - 10% 100% - 10% 100% - 10%
* NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
D2 / DIML2 0-10V DIMMING W/RELAY TO SWITCH POWER
FIXTURE
DIMMER: 0-10V (BY OTHERS)
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
LED DRIVER
V+
RED
V-
BLACK
NOTE: If switched, non-dimming operation is desired, cap off purple and gray wires individually at installation. Do NOT cap purple and gray wires together.
GREEN GND CLASS 2 CONTROL WIRES LINE
RELAY (BY OTHERS)
NEUTRAL
DIMMER: 0-10V w/ POWER SWITCHING
D2 / DIML2 0-10V DIMMING (NO RELAY)
FIXTURE
(BY OTHERS)
LINE
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
LED DRIVER
V+
RED
V-
BLACK
NOTE: If switched, non-dimming operation is desired, cap off purple and gray wires individually at installation. Do NOT cap purple and gray wires together.
GREEN
GROUND
GND
NEUTRAL
USAI Lighting
®
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-2 Revised 03/22/2017
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D3 / DIML3
®
USAI Lighting
DIMMING DRIVER WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D3 / DIML3 LED: Lutron Hi-Lume A-Series 2 Wire Fwd Phase (with neutral) / LED Dimming Driver Wiring (Dims down to 1%) 120V D3 / DIML3 Dimmer Compatibility Chart Manufacturer 120V Only ETC ETC Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron
Product
Part Number
Dimmed Light Output Range
Sensor+ Cabinet Unison DRd Cabinet Maestro Wireless® 600W dimmer Maestro Wireless® 1000W dimmer HomeWorks® QS adaptive dimmer HomeWorks® QS 600W dimmer HomeWorks® QS 1000 W dimmer Caseta Wireless® Pro 1000W dimmer Stanza® dimmer RadioRA® 2 adaptive dimmer RadioRA® 2 1000 W dimmer myRoom DIN power module HomeWorks® QS wallbox power module Homeworks® DIN power module HomeWorks® wallbox power module GRAFIK Eye® QS control unit GRAFIK Eye® 3000 control unit RPM-4U module RPM-4A module GP dimming panels Ariadni CL 250W dimmer Diva CL 250W dimmer Grafik T CL or RF CL dimmer Nova T CL 250W dimmer
ELV10 ELV10 MRF2-6ND-120MRF2-10ND-120HQRD-6NAHQRD-6NDHQRD-10NDPD-10NXDSZ-6NDRRD-6NARRD-10NDMQSE-4A1-D HQRJ-WPM-6D-120LQSE-4A1-D HWI-WPM-6D-120 QSGR-, QSGRJGRX-3100-, GRX-3500HW-RPM-4U-120, LP-RPM-4U-120 HW-RPM-4A-120, LP-RPM-4A-120 Various AYCL-253PDVCL-253P-, DVSCCL-253PGT-250M-, GTJ-250MNTCL-250-
100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100%-1% 100%-1% 100%-1% 100%-1%
Qty Fixtures Per Dimmer* Fixture Wattage 39W and Less 40W - 80W 1 – 26 1 – 13 1 – 26 1 – 13 1–8 1–4 1 – 13 1–6 1–8 1–4 1–8 1–4 1 – 13 1–6 1 – 13 1–6 1–8 1–4 1–8 1–4 1–6 1–3 1–6 1–3 1 – 26 1 – 13 1–6 1–3 1 – 26 1 – 13 1 – 26 1 – 13 1 – 26 1 – 13 1 – 26 1 – 13 1 – 26 1 – 13 1 – 26 1 – 13 1–8 1–4 1–8 1–4 1–8 1–4 1 – 10 1–5
* NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
D3 / DIML3 2 WIRE PHASE DIMMING FIXTURE
DIMMER: 2 WIRE PHASE (BY OTHERS)
LED LINE
SWITCHED HOT NEUTRAL GROUND
BLACK WHITE
DRIVER
V+
RED
V-
BLACK
GREEN GND
ONLY FOR SWITCHES WITH NEUTRAL
NEUTRAL
USAI Lighting
®
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-3 Revised 03/22/2017
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D4 / DIML4
®
USAI Lighting
DIMMING DRIVER WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D4 / DIML4 LED: Lutron Hi-Lume A-Series LED Driver with 3-Wire FL Control / LED Dimming Driver Wiring (Dims down to 1%)
Manufacturer 120V Only ETC ETC Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron 277V Only ETC ETC Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron Lutron
Product
D4 / DIML4 3-Wire Dimmer Compatibility Chart Dimmed Light Part Number Output Range
Sensor+ Cabinet Unison DRd Cabinet Nova T Nova T Nova Nova Vareo Skylark Diva Ariadni Vierti Maestro Maestro Wireless RadioRA 2 HomeWorks QS Interfaces GP Dimming Panels
D20 Dimming module D20F Dimming module NTF-10NTF-103PNF-10NF-103PVF-10SF-10P-, SF-103PDVF-103P-, DVSCF-103PAYF-103PVTF-6AMAF-6AM-, MSCF-6AMMRF2-F6AN-DVRRD-F6AN-DVHQRD-F6AN-DV PHPM-3F-120, PHPM-3F-DV Various
100% - 1% 100% - 1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1%
Sensor+ Cabinet Unison DRd Cabinet Nova T Nova T Nova Nova Skylark Diva Ariadni Vierti Maestro Maestro Wireless RadioRA 2 HomeWorks QS Interfaces GP Dimming Panels
D20 Dimming module D20F Dimming module NTF-10-277NTF-103P-277NF-10-277NF-103P-277SF-12P-277-, SF-12P-277-3 DVF-103P-277-, DVSCF-103P-277AYF-103P-277VTF-6AMAF-6AM-277-, MSCF-6AM-277MRF2-F6AN-DVRRD-F6AN-DVHQRD-F6AN-DV PHPM-3F-DV Various
100% - 1% 100% - 1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1% 100%–1%
Qty Fixtures Per Control* Fixture Wattage 39W and Less 40W - 80W 1–53 1–26 1–53 1–26 1–41 1 – 20 1–20 1 – 10 1–41 1 – 20 1–20 1 – 10 1–20 1 – 10 1–20 1 – 10 1–20 1 – 10 1–20 1 – 10 1–15 1–7 1–15 1–7 1–15 1–7 1–15 1–7 1–15 1–7 1–41 1 – 20 1–41 1 – 20 40W and Less 41W - 80W 1–53 1–26 1–53 1–26 1–44 1 – 22 1–33 1 – 16 1–44 1 – 22 1–33 1 – 16 1–33 1 – 16 1–33 1 – 16 1–44 1 – 22 1–33 1 – 16 1–20 1 – 10 1–33 1 – 16 1–33 1 – 16 1–33 1 – 16 1–88 1 – 44 1–88 1 – 44
* NOTE: Number of fixtures may be higher if wattage is less than maximum values shown. Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
DIML4 wiring diagrams continued on next page
USAI Lighting
®
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-4 Revised 03/22/2017
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D4 / DIML4 Continued
®
USAI Lighting
DIMMING DRIVER WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D4 / DIML4 LED: Lutron Hi-Lume A-Series LED Driver with 3-Wire FL Control / LED Dimming Driver Wiring (Dims down to 1%) D4 / DIML4 3 WIRE PHASE DIMMING
FIXTURE
DIMMER: 3 WIRE PHASE (BY OTHERS)
CAP UNUSED ECOSYS WIRES DIMMED HOT SWITCHED HOT NEUTRAL
LINE
LED
PURPLE GRAY PURPLE ORANGE BLACK WHITE GREEN
GROUND
DRIVER
V+
RED
V-
BLACK
GND NEUTRAL
D4 / DIML4 LED: Lutron Hi-Lume A-Series LED Driver with EcoSystem Control / LED Dimming Driver Wiring (Dims down to
Manufacturer 120V / 277V Lutron Lutron Lutron Lutron
D4 / DIML4 EcoSystem Dimmer Compatibility Chart Dimmed Light Part Number Output Range
Product
PowPak dimming module Energi Savr Node GRAFIK Eye QS (120V ONLY) Quantum
RMJ-ECO32-DV-B QSN-1ECO-S, QSN-2ECO-S QSGRJ-_E, QSGR-_E Various
100%–1% 100%–1% 100%–1% 100%–1%
Qty Fixtures Per Control* Fixture Wattage 39W and Less 40W - 80W 1–32 1 – 16 1–64 1 – 32 1–64 1 – 32 1–64 1 – 32
* NOTE: Number of fixtures may be higher if wattage is less than maximum values shown. Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
D4 / DIML4 EcoSystem CONTROLS ECOSYS BUS E2 E1
E2
FIXTURE
E1
WALL CONTROL (BY OTHERS)
LINE NEUTRAL
CAP UN-USED ORANGE WIRE
PURPLE GRAY PURPLE ORANGE BLACK WHITE GREEN
LED
DRIVER
V+
RED
V-
BLACK
GND
USAI Lighting
®
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-4 Revised 03/22/2017
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D4E / DIML4E and D4H /DIML4H
®
USAI Lighting
DIMMING DRIVER WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D4E / DIML4E LED: Lutron 5 Series EcoSystem LED Driver / LED Dimming Driver Wiring (Dims down to 5%)
Manufacturer 120V / 277V Lutron Lutron Lutron Lutron
D4E / DIML4E EcoSystem Dimmer Compatibility Chart Dimmed Light Part Number Output Range
Product
PowPak dimming module Energi Savr Node GRAFIK Eye QS (120V ONLY) Quantum
RMJ-ECO32-DV-B QSN-1ECO-S, QSN-2ECO-S QSGRJ-_E, QSGR-_E Various
100%–5% 100%–5% 100%–5% 100%–5%
Qty Fixtures Per Control* Fixture Wattage 39W and Less 40W - 80W 1–32 1 – 16 1–64 1 – 32 1–64 1 – 32 1–64 1 – 32
* NOTE: Number of fixtures may be higher if wattage is less than maximum values shown. Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
D4H / DIML4H LED: Lutron H Series EcoSystem LED Driver with Fade to Black (dims down to 1%)
Manufacturer 120V / 277V Lutron Lutron Lutron Lutron
D4H / DIML4H EcoSystem Dimmer Compatibility Chart Dimmed Light Part Number Output Range
Product
PowPak dimming module Energi Savr Node GRAFIK Eye QS (120V ONLY) Quantum
RMJ-ECO32-DV-B QSN-1ECO-S, QSN-2ECO-S QSGRJ-_E, QSGR-_E Various
100%–1% 100%–1% 100%–1% 100%–1%
Qty Fixtures Per Control* Fixture Wattage 39W and Less 40W - 80W 1–32 1 – 16 1–64 1 – 32 1–64 1 – 32 1–64 1 – 32
* NOTE: Number of fixtures may be higher if wattage is less than maximum values shown. Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
D4E / DIML4E and D4H / DIML 4H EcoSystem CONTROLS ECOSYS BUS E2 E1
E2
FIXTURE
E1
WALL CONTROL (BY OTHERS)
LED
PURPLE GRAY PURPLE LINE
BLACK
NEUTRAL
WHITE
DRIVER
V+
RED
V-
BLACK
GREEN GND
USAI Lighting
®
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-4EH Revised 03/22/2017
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D6A / DIML6A and D6E / DIML6E D6B / DIML6B and D6F / DIML6F
®
USAI Lighting
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D6A / DIML6A and D6E / DIML6E LED Dimming Compatibility Table D6A / DIML6A and D6E / DIML6E are linearly programmed dimming drivers for use with logarithmic-style dimming controls (e.g., Lutron and others listed in the table below) D6A / DIML6A = EldoLED SOLOdrive 0-10V control dims from 100% to 0.1% D6E / DIML6E = EldoLED ECOdrive 0-10V control dims from 100% to 1% D6A / DIML6A and D6E / DIML6E Dimmer Compatibility Chart Dimmed Light Qty Fixtures Manufacturer Product Part Number Output Range Per Dimmer* 120V & 277V DIML6A 6E Refer to manufacturer's Lutron Diva DVTV/NFTV/NTFTV with PP-20 99% - 0.1% 1% dimmer load rating for Lutron Energi Savr Node QSN-4T16-S 100% - 0.1% 1% maximum and minimum Lutron GP Dimming Panels TVM2 Module 99% - 0.1% 1% fixture quantities per Lutron Interfaces GRX-TVI w/ GRX3503 100% - 0.1% 1% dimmer. Sensor Switch nIO nIO EZ 100% - 0.1% 1% Enlighted compatible. enlighted Control Unit CU-3E-1R 100% - 0.1% 1% * NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
D6B / DIML6B and D6F / DIML6F LED Dimming Compatibility Table D6B / DIML6B and D6F / DIML6F are logarithmic-programmed dimming drivers for use with linear-style dimming controls (e.g., Crestron, non-Lutron and others listed in the table below) DIMMER:SOLOdrive 0-10V D6B / DIML6B = EldoLED 0-10V control dims from 100% to 0.1% (BY OTHERS) D6F / DIML6F = EldoLED ECOdrive 0-10V control dims from 100% to 1% LED 0-10V (-) GRAY D6B / DIML6B and D6F / DIML6F Dimmer Compatibility Chart 0-10V (+) PURPLE Dimmed Light Qty Fixtures V+ RED SWITCHED HOT SWITCHED HOTNumber DRIVER Manufacturer Product Part Output Range Per Dimmer* VBLACK NEUTRAL WHITE 120V & 277V DIML6B 6F Refer to GREEN 2112U-101 Bush-Jaeger Electronic potentiometer 100% - 0.1% 1% manufacturer's Jung Electronic potentiometer 100% - 0.1% 1% dimmer load GND 240-10 CLASS 2 CONTROL WIRES Leviton IllumaTech dimmer IP710-DLX 100% - 0.1% 1% rating for LINE Lightolier (Philips) Momentum (120V ONLY) ZP600FAM120 100% - 0.1% 1% maximum and RELAY Merten Electronic potentiometer 5729 100% - 0.1% 1% minimum fixture (BY OTHERS) DIML6A, 6B Pass & Seymour Titan CD4FB-W 100% - 0.1% 1% quantities per NEUTRAL TO SWITCH POWER Watt Stopper Miro 0-10V DIMMING W/RELAY DCLV1 100% - 0.1% 1% dimmer. Synergy Wallbox Dimmers ISD BC 100% - 0.1% 1% Enlighted ABB i-bus SD/S 2.16.1 100% - 0.1% 1% compatible. Crestron Modules GLX-DIMFLV8, GLXP-DIMFLV8 100% - 0.1% 1% Crestron Green Light GLPAC-DIMFLV4-, GLPAC-DIMFLV8100% - 0.1% 1% DIML6A, 6B 0-10V (-) Crestron Green Light Power Pack GLPP-DIMFLVEX-PM, GLPP-1DIMFLV2EX-PM, GLPP-1DIMFLV3EX-PM 100% - 0.1% FIXTURE 1% 0-10V DIMMING W/RELAY TO GRAY SWITCH POWER 0-10V (+) PURPLE DIMMER: 0-10V Crestron DIN Rail Analog Output Module DIN-A08 100% - 0.1% 1% V+ RED SWITCHED HOT BLACK Crestron DIN Rail 0-10V Fluorescent Dimmer DIN-4DIMFLV4 100% - 0.1% 1% LEDV- BLACK NEUTRAL WHITE GREEN Crestron iLux 0-10V Dimmer Expansion Module CLS-EXP-DIMFLV 100% - 0.1% 1% DRIVER GND enlighted Control Unit CU-3E-1R 100% - 0.1% 1% CLASS 2 CONTROL WIRES * NOTE: Refer to dimmer manufacturer's documentation for installation instructions and LINEcircuit details. (BY OTHERS)
RELAY
(BY OTHERS)
DIMMING DRIVER WIRING SCHEMES:
NEUTRAL
NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details. D6 / DIML6 0-10V DIMMING W/RELAY TO SWITCH POWER
D6 / DIML6 0-10V DIMMING (NO RELAY)
FIXTURE
DIMMER: 0-10V 0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
LED DRIVER
V+
RED
V-
BLACK
(BY OTHERS)
LINE
GREEN GROUND
GND CLASS 2 CONTROL WIRES LINE
FIXTURE
DIMMER: 0-10V w/ POWER SWITCHING
(BY OTHERS)
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
LED DRIVER
V+
RED
V-
BLACK
GREEN GND
RELAY (BY OTHERS)
NEUTRAL NEUTRAL
USAI Lighting
®
www.usailighting.com DIML6A, 6B
[email protected]
1126 River Road New Windsor, NY 12553
0-10V DIMMING (NO RELAY)
DIMMER: 0-10V w/ POWER SWITCHING (BY OTHERS)
FIXTURE
T 845–565–8500 F 845–561–1130
© 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-6 Revised 03/22/2017
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D7 / DIML7
®
USAI Lighting
DIMMING DRIVER WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D7 / DIML7 LED: EldoLED DALI Dimming Driver Wiring (Dims down to 0.1%)
D7 / DIML7 DALI CONTROLS DALI BUS DA DA
FIXTURE WALL CONTROL (BY OTHERS)
LINE NEUTRAL
LED
ORANGE (-) ORANGE/WHITE (+) BLACK WHITE GREEN
DRIVER
V+
RED
V-
BLACK
GND
USAI Lighting
®
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-7 Revised 03/22/2017
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D15 / DIML15
®
USAI Lighting
DIMMING DRIVER WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D15 / DIML15 LED: 0-10V, 347V Dimming Driver Wiring (Dims down to 1%) 347V Only
Manufacturer 347 Acuity Douglas Lighting Hubbell Leviton Leviton Lutron Lutron
Product
D15 / DIML15 Dimmer Compatibility Chart Dimmed Light Output Range
Synergy ISD-BC WPN-5721, WPN-5822 Light Hawk2 LHD-IRS3-N347-xx Illumatech IP710-DLZ with 347V relay Centura Fluorescent Control System Nova NFTV-* dimmer plus 347V relay Diva DVTV-* dimmer plus 347V relay
Qty Fixtures Per Dimmer* Use source current per fixture specification sheet to determine number of fixtures per dimmer. Max number of fixtures is limited by dimmer load rating.
100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1% 100% - 1%
* NOTE: Refer to dimmer manufacturer's documentation for installation instructions and circuit details.
D15 / DIML15 0-10V DIMMING W/RELAY TO SWITCH POWER FIXTURE DIMMER: 0-10V (BY OTHERS)
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
LED DRIVER
V+
RED
V-
BLACK
NOTE: If switched, non-dimming operation is desired, cap off purple and gray wires individually at installation. Do NOT cap purple and gray wires together.
GREEN GND CLASS 2 CONTROL WIRES LINE
RELAY (BY OTHERS)
NEUTRAL
DIML2 0-10V DIMMING (NO RELAY) FIXTURE
DIMMER: 0-10V w/ POWER SWITCHING (BY OTHERS)
LINE
0-10V (-)
GRAY
0-10V (+)
PURPLE
SWITCHED HOT
BLACK
NEUTRAL
WHITE
USAI Lighting
NEUTRAL
DRIVER
RED
V-
BLACK
GREEN
GROUND ®
LED V+
www.usailighting.com
[email protected]
1126 River Road New Windsor, NY 12553
GND
T 845–565–8500 F 845–561–1130
NOTE: Quickship fixtures are shipped prewired for 0-10V dimming controls. If switched, nondimming operation is desired, cap off purple and gray wires separately at installation. Do NOT cap purple and gray wires together. © 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-15 Revised 03/22/2017
DIMMING DRIVER COMPATIBILITY SELECTION GUIDE D19 / DIML19
®
USAI Lighting
DIMMING DRIVER WIRING SCHEMES: NOTES: Wiring diagrams are examples of typical installations intended to illustrate the number of wires that must be run to fixture. These diagrams are not intended to specify all equipment necessary for a given dimming circuit. Refer to specific dimmer manufacturer's documentation for details.
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS 1. Keep these instructions in a safe place for future reference. 2. Only qualified electricians in accordance to local codes should install these fixtures. 3. De-energize the electrical circuit at the circuit breaker prior to installation process or servicing. 4. Make sure all connections are in accordance with the National Electrical Code and any local regulations. 5. Cap any wires not used separately (not together).
D19 / DIML19 LED: Hatch XTC series or equivalent - Forward and Reverse Phase Dimming Driver. Dims down to 1% contingent upon dimmer specification and load. 120V only. D19 / DIML19 2 WIRE PHASE DIMMING FIXTURE
DIMMER: 2 WIRE PHASE (BY OTHERS)
LED LINE
SWITCHED HOT NEUTRAL GROUND
BLACK
DRIVER
WHITE
V+
RED
V-
BLACK
GREEN GND
ONLY FOR SWITCHES WITH NEUTRAL
NEUTRAL
D19 / DIML19 Dimmer Compatibility Chart 120V ONLY Forward Phase / TRIAC Dimming Manufacturer Product Qty Fixtures Per Dimmer Leviton IPL06-10Z Use fixture wattage per 6613-xxx fixture specification Lutron S-600P sheet to determine S-603P number of fixtures DV-600P per dimmer. Max number DV-603P of fixtures is limited by DVSC-603P dimmer load rating. CT-600P CT-603P 120V ONLY Reverse Phase / ELV Dimming Manufacturer Product Leviton 6615 IPE04-xxx Lutron NTELV-300 NTELV-600 SELV-300P SELV-303P DVELV-300P DVELV-303P
USAI Lighting
®
www.usailighting.com
[email protected]
Qty Fixtures Per Dimmer Use fixture wattage per fixture specification sheet to determine number of fixtures per dimmer. Max number of fixtures is limited by dimmer load rating.
1126 River Road New Windsor, NY 12553
T 845–565–8500 F 845–561–1130
© 2016. USAI, LLC. All rights reserved. All designs protected by copyright. I2-264-19 Revised 03/22/2017
