Transcript
OPTEX (EUROPE) LIMITED
Instruction Manual
BGR-01
OPTEX Ricochet wireless transmitter
OPTEX (EUROPE) LIMITED
Instruction Manual
BGR-01
OPTEX Ricochet wireless transmitter
LED
Battery Only replace with 3V Lithium CR123A Battery Safety • Do not heat • Do not charge • Do not short circuit • Do not disassemble • Replace only with same or equivalent type • Always observe local regulations when disposing of a battery • Detector will transmit low battery warning when battery needs replacing
Optex Detector ID DIP Switch
1. Alarm 2 Alarm 3. Power out 4. Power Out + (Beams Only) 1. Tamper 2. Tamper 3. Low Battery 4. Low Battery 1. Tamper/ Trouble 2. Tamper/ Trouble
LED
4
Optex sensor 2. Connect Optex sensor directly using 4way and/or 2way plug (VXI, FTN, RXC-RST). For HX, BX and Active Beams use the supplied cables 3. Install the CR123A battery to learn the device on to the system
1. Tamper/ Trouble 2. Tamper/ Trouble
3
Connection
(Beams Only) 1. Tamper 2. Tamper 3. Low Battery 4. Low Battery
2
Note: For use with Texecom Premier Elite with
1. Alarm 2 Alarm 3. Power out 4. Power Out +
1
Introduction • For wireless connectivity, detailed programming and system set-up instructions please refer to the compatible RICOCHET™ technology enabled Premier Elite wireless expander instructions. • Featuring RICOCHET™ wireless technology, the BGR-01 is designed for Optex battery powered devices for professional security installations. • When using the BGR-01 on an Entry/Exit route, or where chime is required, the device attributes should be set to “Always Awake”. • Please see the Premier Elite 8XP-W/32XP-W Installation Manual for details of how to change the device attributes • For wiring and installation instructions refer to OPTEX device manual. The supplied wiring loom may not be required for some OPTEX devices, in this case use (the supplied) device wiring loom. • Active Beams can use either one or two Ricochet BGR-01
Optex Detector ID DIP Switch
4
Optex sensor 2. Connect Optex sensor directly using 4way and/or 2way plug (VXI, FTN, RXC-RST). For HX, BX and Active Beams use the supplied cables 3. Install the CR123A battery to learn the device on to the system
• Do not heat • Do not charge • Do not short circuit • Do not disassemble • Replace only with same or equivalent type • Always observe local regulations when disposing of a battery • Detector will transmit low battery warning when battery needs replacing
3
Connection
Battery Safety
2
Note: For use with Texecom Premier Elite with
Battery Only replace with 3V Lithium CR123A
1
Introduction • For wireless connectivity, detailed programming and system set-up instructions please refer to the compatible RICOCHET™ technology enabled Premier Elite wireless expander instructions. • Featuring RICOCHET™ wireless technology, the BGR-01 is designed for Optex battery powered devices for professional security installations. • When using the BGR-01 on an Entry/Exit route, or where chime is required, the device attributes should be set to “Always Awake”. • Please see the Premier Elite 8XP-W/32XP-W Installation Manual for details of how to change the device attributes • For wiring and installation instructions refer to OPTEX device manual. The supplied wiring loom may not be required for some OPTEX devices, in this case use (the supplied) device wiring loom. • Active Beams can use either one or two Ricochet BGR-01
DIP switch settings OPTEX Detector ID SL-350-QxR Reciever SL-350-QxR Transmitter AX-x00-TFR Reciever AX-x00-TFR Transmitter
LED status indication DIP Setting ON
ON
1 OFF
ON
1
2
3
4
OFF
1
ON
ON
2
3
4
3 OFF
1
ON
ON
OFF
1
2
3
4
2
3
4
5 OFF
1
ON
ON
OFF
1
2
3
4
2
3
4
6
HX-xxR ON
ON
OFF
1
ON
ON
OFF
1
ON
ON
2
3
4
2
3
4
VXI-Rx
RXC-RST 2
3
AX-x00-TFR Reciever AX-x00-TFR Transmitter
ETSI EN300-220(V2.4.1)
Frequency Band:
868.0 – 868.6 MHz
Product type:
BGR-001 868MHz Category 1, Class 2
Tamper or trouble has transitioned from open to close
(Listen Before Talk) Yes
Transmitter Duty Cycle
868MHz<1%
Communication successful
Low Voltage Signal 2.85v Operating Voltage 3v
Connection Tables 1. Yellow 2. White 3. Black 4. Red
Alarm in Alarm In Power –ve out Power +ve out
1. Blue 2. Green
Tamper/Trouble Tamper/Trouble (Rx) Alarm in (Rx) Alarm In Not used Not used
8
1. Orange 2. Brown 3. Purple 4. Grey
(Tx&Rx) Tamper (Tx&Rx) Tamper (Tx&Rx) Low Battery (Tx&Rx) Low Battery
1. Blue 2. Green
(Rx) DQ (Rx) DQ
4
RADIO
Receiver:
1. Yellow 2. White 3. Black 4. Red
9 1
Slow Flash 0.5s
EN50130-4:2014:A1:A2 ETSI EN301 489-03 V1.6.1:2013
Receiver LBT
7
DIP switch settings
SL-350-QxR Transmitter
Blinks every 0.5s
Tamper or Trouble inputs are open.
Active Beams SL and AX (use supplied cables)
FTN-Rx
SL-350-QxR Reciever
On learn fail, attempting to connect to learnt network
VXI-Rx FTN-Rx RXC-RST BX-80xR HX-xxR
ON
BX-80xR
OPTEX Detector ID
Rapid Flash
Solid for 3s
4
OFF
On power-up, while learning to network
ON
2
ON
Solid
EMC:
Maximum current
32mA
Quiescent current 60uA
Warranty
2 year replacement warranty (excludes battery). The BGR-01 is designed to be used with OPTEX battery powered detection devices and activate an alarm control panel. As the BGR-01 is not a complete alarm system, but only part thereof, Optex cannot accept responsibility or liability for any damages whatsoever based on a claim that the BGR-01 failed to function correctly.
Made in England
LED status indication
ON
ON
1 OFF
1
ON
ON
2
3
4
2 OFF
1
ON
ON
OFF
1
ON
ON
2
3
4
3 2
3
4
1
ON
ON
OFF
1
ON
ON
OFF
1
ON
ON
OFF
1
ON
ON
OFF
1
ON
ON
2
3
3
HX-xxR 2
3
BGR-001 868MHz
Blinks every 0.5s
Receiver:
Category 1, Class 2
Slow Flash 0.5s
Tamper or trouble has transitioned from open to close
Receiver LBT
(Listen Before Talk) Yes
Transmitter Duty Cycle
868MHz<1%
Communication successful
Low Voltage Signal 2.85v
Connection Tables
6
Tamper/Trouble Tamper/Trouble
7
1. Yellow 2. White 3. Black 4. Red
(Rx) Alarm in (Rx) Alarm In Not used Not used
8
1. Orange 2. Brown 3. Purple 4. Grey
(Tx&Rx) Tamper (Tx&Rx) Tamper (Tx&Rx) Low Battery (Tx&Rx) Low Battery
1. Blue 2. Green
(Rx) DQ (Rx) DQ
Active Beams SL and AX (use supplied cables)
2
3
4
2
3
4
VXI-Rx
RXC-RST
9 1
Product type:
Tamper or Trouble inputs are open.
1. Blue 2. Green
4
FTN-Rx
OFF
On learn fail, attempting to connect to learnt network
Alarm in Alarm In Power –ve out Power +ve out
4
2
3
4
ETSI EN300-220(V2.4.1) 868.0 – 868.6 MHz
Rapid Flash
1. Yellow 2. White 3. Black 4. Red
5 2
RADIO Frequency Band:
VXI-Rx FTN-Rx RXC-RST BX-80xR HX-xxR
4
BX-80xR
On power-up, while learning to network
Solid
Solid for 3s
4 OFF
EN50130-4:2014:A1:A2 ETSI EN301 489-03 V1.6.1:2013
EMC:
DIP Setting
Operating Voltage 3v Maximum current
32mA
Quiescent current 60uA
Warranty
2 year replacement warranty (excludes battery). The BGR-01 is designed to be used with OPTEX battery powered detection devices and activate an alarm control panel. As the BGR-01 is not a complete alarm system, but only part thereof, Optex cannot accept responsibility or liability for any damages whatsoever based on a claim that the BGR-01 failed to function correctly.
Made in England
