Transcript
PALM BLADDER SCANNER Palm Bladder Scanner An easy guide in six steps. 1 2 3 4 5 6 7
•Indicator light: indicating the present status. •LCD screen: displaying images and result after measuring. •POWER key: power switch.
4
•SCAN key: start of pre-scan function then of measurement. •PRINT key: print control. •Navigation key: direction control and function key. •OK key: confirm and reset.
1
3
5
2
7
6
Fig.1
Navigation keys Their function changes in each screen mode. The current function is displayed on the screen
=
Step 1
or
or
Push the power button (3) for at least 3 seconds and the following screen will be displayed. (Fig.2)
Ph: 1300 009 663 Fax: 1300 099 300 Email:
[email protected] 7/22 Mavis Court, Yatala, Qld, 4207 w w w. zo n e m e d i c a l. co m . a u
NEW ZEALAND
AUSTRALIA
After self check Fig.2 press right navigation key to continue and enter into “Ready” screen Fig.3
Ph: 0800 009 663 Fax: 0800 109 663 E m a i l : i n fo @ z o n e m e d i c a l. c o. n z P O B ox 3 2 2 D a n ne v i r k e NZ 4942 w w w.zonemedical.co.nz
Fig.2
Fig.3 Status bar
+ Function- navigation keys
Step 2 Step 2
Select gender by pressing gender button, every time you want to change. Gender will change in female and male as shown at the pictogram.
Step 3
Fig.4
•The location of the bladder might vary.
•Align probe in the middle of the patient (point scan key on probe towards patients head; see fig.5 below) Grey scale •Press Scan-key (no.4, fig.1) to enter the pre-scan function. Fig.4 •Ensure the bladder is completely in the window.
Black / white
•Press the Scan-key again for scanning and calculation. Press the Scan-key on the main machine or the scan button on the probe (Fig.5) and hold in position.
scan key
Fig.5 probe
60° Fig.6 os pubis bladder
Step 4 •During scanning and calculation process you see Fig. 7 •You can choose your preferred screen display, grey-scale Fig.8 or with a red line contour Fig. 9 •If you have not aligned the bladder correctly in the window go to Fig.10 for help (next page)
Fig.7
To switch for the next page and see the other four images (frames), press “Next” button on the navigation keys.
To switch for grey-scale or black and white interface, press “Switch” button.
Fig.8
Fig.9 Current result
Max. scanned result in this patient sequence
Step 5 1.
Review the 12 frames (1 up to and including 4 are shown in above interfaces) and accept result if they are completely in the window
2.
The screen shows a projection of the bladder in the circle above the scanned volume. If the bladder is out of the circle, it means that it is partly out of the scanning area.
3.
In Fig.9 the bladder is given a red line contour.
4.
Check that the area of the bladder is within the red line. If not you should scan again.
PALM BLADDER SCANNER Fig.10 Help for aiming: Arrow Guiding Location System for locating the bladder. Hold the scan key side of the probe (see fig.5) in the direction of the patients head. The scan result will be checked by the "Arrow Guiding Location System" and if necessary the system will give an arrow, how to aim in an better way. If the bladder is not correctly aligned in the window, or if the image of the bladder in the circle is incomplete (see step 5 point 2), retry using steps outlined in fig.10.
left down
right down
probe head down
probe head up
left up
right up
probe head left
probe head right
Fig.11
Step 6 After scanning, patient data may be added by pressing left button Save/Edit Fig.11 and Fig.12 In the “Edit” screen the name or number of the patient can be added, using the navigation keys to scroll through the alphabet. The colour of the active key will light up white. Press “Print”- key to save edited ID, and “Scan”- key to return to “Ready” (Fig.3).
Fig.12
Ph: 1300 009 663 Fax: 1300 099 300 Email:
[email protected] 7/22 Mavis Court, Yatala, Qld, 4207 w w w. zo n e m e d i c a l. co m . a u
NEW ZEALAND
AUSTRALIA
Bladder
Ph: 0800 009 663 Fax: 0800 109 663 E m a i l : i n fo @ z o n e m e d i c a l. c o. n z P O B ox 3 2 2 D a n ne v i r k e NZ 4942 w w w.zonemedical.co.nz