Transcript
Universal Wireless DMX
Blizzard Lighting, LLC www.blizzardlighting.com Waukesha, WI USA Copyright (c) 2016
TABLE OF CONTENTS Colorise™ Zoom 1 1. Getting Started 3 What’s In The Box? 3 Getting It Out Of The Box 3 Powering Up! 3 Getting A Hold Of Us 3 Safety Instructions (Don’t run with scissors!) 4
2. Meet The Colorise™ Zoom LED Par
5
Main Features 5 DMX Quick Reference 5 The Colorise™ Zoom Pin-up Picture 6
3. Setup 7
Connecting A Bunch Of Colorise™ Zoom Fixtures 7 Data/DMX Cables 7 Setting the DMX Input Connector as the Active DMX Input 7 Cable Connectors 8 3-Pin??? 5-Pin??? Huh? 8 Take It To The Next Level: Setting up DMX Control 8 Fixture Linking (Master/Slave Mode) 9 Mounting/Rigging 9 Using the AnyFi™ Wireless DMX Receiver 10 Setting the Fixture to Receive Wireless Signal 10 Resetting The Wireless 10 Select W-DMX™ or Skywire 2.4GHz Receiver 10 Successful W-DMX™ Connections 11 Skywire™ 6/7-Channel Modes: Selecting the Channel Group 11
4. Operating Adjustments 12 Navigating The Control Panel 12 Control Panel Menu Structure 13 DMX Mode 14 Set the Starting DMX Address 14 Setting the DMX Channel Mode 14 Slave Mode 14 Dimming Mode Settings 14 LED Display On/Off and Menu Lock 14 Custom Programs 15 Auto, Speed, and Sound Active Modes 15 Color Calibration Settings 16 Custom Static Colors & Preset Colors 16 Fixture Reset Functions 17 Data Sync Feature 17 Fixture Information 17 DMX Value In-Depth Reference Guide 18 DMX In-Depth Reference 19
5. Appendix 20 A Quick DMX Lesson 20 Troubleshooting 20 Keeping Your Colorise™ Zoom As Good As New 21 Returns (Gasp!) 21 Shipping Issues 21 Tech Specs 22 Dimensional Drawings 23
Page 2
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
1. GETTING STARTED What’s In The Box?
• • • •
1 x Colorise™ Zoom Professional LED PAR Fixture An Ever-So-Handy Power Cord One Really Classy DMX Cable This Lovely User Manual
Getting It Out Of The Box Congratulations on the purchase of your new totally sweet Colorise™ Zoom LED par fixture. She’s a real stunner alright, definitely the cat’s pajamas! Now that you’ve got your Colorise™ Zoom (or hopefully, Colorises!), you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition. If anything looks as if it has been damaged in transit, notify the shipper immediately and keep the packing material for inspection. Again, please save the carton and all packing materials. If a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Powering Up! All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. AC Voltage Switch - Not all fixtures have a voltage select switch, so please verify that the fixture you receive is suitable for your local power supply. See the label on the fixture or refer to the fixture’s specifications chart for more information. A fixture’s listed current rating is its average current draw under normal conditions. Check the fixture or device carefully to make sure that if a voltage selection switch exists that it is set to the correct line voltage you will use. Warning! Verify that the voltage select switch on your unit matches the line voltage applied. Damage to your fixture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch. All fixtures must be connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, please just visit our website at www.blizzardlighting. com/support and open a support ticket. We’ll be happy to help, honest. Disclaimer: The information and specifications contained in this document are subject to change without notice. Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time. You can download the latest version of this document from www.blizzardlighting.com. Author:
Date:
Last Edited:
Date:
J. Thomas
3/24/2016
J. Thomas
6/30/2016
Page 3
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone else, be sure that they also receive this User Guide. • ALWAYS make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. • This product is intended for indoor use only. • To prevent risk of fire or shock, do not expose fixture to rain or moisture. • Make sure there are no flammable materials close to the unit while operating. • The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked. • ALWAYS disconnect from the power source before servicing or replacing fuse and be sure to replace with same fuse size and type. • ALWAYS secure fixture using a safety chain. NEVER carry the fixture by its cord. Use its carrying handles. • DO NOT operate at ambient temperatures higher than 104°F (40°C). • In the event of a serious operating problem, stop using the unit immediately. NEVER try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts. • NEVER connect the device to a dimmer pack. • Make sure the power cord is never crimped or damaged. • Never disconnect the power cord by pulling or tugging on the cord. • Avoid direct eye exposure to the light source while it is on. Caution! There are no user serviceable parts inside this unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please visit http://www.blizzardlighting.com/support.
Page 4
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
2. MEET THE COLORISE™ ZOOM LED PAR MAIN FEATURES • • • • • • • • • •
36x 3W R/G/B/A/W LEDs, 100,000 hours Built-in AnyFi™ wireless DMX receiver (Skywire™ or W-DMX™) User selectable 32-bit dimming curves Variable electronic dimmer strobe Built-in color & chase macros via DMX Built-in auto programs in standalone and M/S Color mixing ability in standalone mode 10°-40° zoomable beam angle LED control panel with 4* touch sensitive buttons User selectable 5/7/9 or 11-channel DMX modes
ADDITIONAL FEATURES • • • • •
Rugged and well-built (It hits the gym regularly) Natural convection cooled, totally silent operation Dual mounting brackets for positioning flexibility 3/5-pin XLR input and output connections PowerCon™ compatible AC power In/Out connectors
DMX Quick Reference - 11/9/7-Channel Modes Channel
11-Channel
9-Channel
7-Channel
1
Dimmer
Dimmer
Dimmer
2
Red Intensity
Red Intensity
Red Intensity
3
Green Intensity
Green Intensity
Green Intensity
4
Blue Intensity
Blue Intensity
Blue Intensity
5
Amber Intensity
Amber Intensity
Amber Intensity
6
White Intensity
White Intensity
White Intensity
7
Strobe
Strobe
Zoom
8
Zoom
Zoom
---
9
Custom Colors + Auto
32-bit Dimming + Reset
---
10
Auto Speed
---
---
11
32-bit Dimming + Reset
---
---
DMX Quick Reference - 5-Channel Mode Channel
5-Channel
1
Red Intensity
2
Green Intensity
3
Blue Intensity
4
Amber Intensity
5
White Intensity
Page 5
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
Figure 1: The Colorise™ Zoom Pin-Up Picture
36* 3-Watt R/G/B/A/W LEDs
Heavy-Duty Cast Aluminum Enclosure
Dual Mounting Yokes Locking Adjustment Knobs
Figure 2: The Rear Connections
3-Pin DMX Out
5-Pin DMX In
3-Pin DMX In
5-Pin DMX Out
Antenna AC Power In
AC Power Out
Wireless LED Indicator
4-Character LED Control Panel
Page 6
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement CAUTION! The Colorise™ Zoom utilizes a high-output switch-mode power supply with an internal fuse. Under normal operating conditions, the fuse should not require replacement. The fuse is field replaceable, however it is an advanced procedure suited to qualified individuals. Should your fixture require replacement, please contact Blizzard Lighting for instructions, or to return your unit for service. Connecting A Bunch of Colorise™ Zoom Fixtures You will need a serial data link to run light shows using a DMX-512 controller or to run shows on two or more fixtures set to sync in master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. Fixtures on a serial data link must be daisy chained in one single line. Also, connecting more than 32 fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in deterioration of the digital DMX signal. The maximum recommended cable-run distance is 500 meters (1640 ft). The maximum recommended number of fixtures on a serial data link is 32 fixtures. Data/DMX Cabling To link fixtures together you’ll need data cables. You should use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference. For instance, Belden© 9841 meets the specifications for EIA RS-485 applications. Standard microphone cables will “probably” be OK, but note that they cannot transmit DMX data as reliably over long distances. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield Maximum capacitance between conductors – 30 pF/ft. Maximum capacitance between conductor & shield – 55 pF/ft. Maximum resistance of 20 ohms / 1000 ft. Nominal impedance 100 – 140 ohms
Setting the DMX Input Connector as the Active DMX Input Navigate the main menu to reach SET, press , then use the buttons until SIGN is displayed, then press again. Now use the buttons to highlight CABL (cable mode), and press to confirm.
Page 7
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
Cable Connectors Cables must have a male XLR connector on one end and a female XLR connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to verify correct polarity and to make sure the pins are not grounded or shorted to the shield or each other. 3-Pin??? 5-Pin??? Huh?!? If you use a controller with a 5-pin DMX output connector, it’s no problem! you can simply use the installed 5-pin DMX input and/or output connections found on the back of your fixture(s).
Conductor
3-Pin Female (Output)
5-Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data 1- (Primary Data Link)
Pin 2
Pin 2
Data 1+ (Primary Data Link)
Pin 3
Pin 3
Data 2- (Optional Secondary Data Link)
Pin 4
Pin 4
Data 2+ (Optional Secondary Data Link)
Pin 5
Pin 5
Take It To The Next Level: Setting Up DMX Control Step 1: Connect the male connector of the DMX cable to the female connector (output) on the controller. Step 2: Connect the female connector of the DMX cable to the first fixture’s male connector (input). Note: It doesn’t matter which fixture address is the first one connected. We recommend connecting the fixtures in terms of their proximity to the controller, rather than connecting the lowest fixture number first, and so on. Step 3: Connect other fixtures in the chain from output to input as above. Place a DMX terminator on the output of the final fixture to ensure best communication.
Page 8
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode) 1. Connect the (male) 3/5-pin connector side of the DMX cable to the output (female) 3/5-pin connector of the first fixture. 2. Connect the end of the cable coming from the first fixture which will have a (female) 3/5-pin connector to the input connector of the next fixture consisting of a (male) 3/5-pin connector. Then, proceed to connect from the output as stated above to the input of the following fixture and so on. A quick note: Often, the setup for MasterSlave and Standalone operation requires that the first fixture in the chain be initialized for this purpose via either settings in the control panel or DIP-switches. Secondarily, the fixtures that follow may also require a slave setting. Check the “Operating Adjustments” section in this manual for complete instructions for this type of setup and configuration. Mounting & Rigging This fixture may be mounted in any SAFE position provided there is enough room for ventilation. It is important never to obstruct the fan or vents pathway. Mount the fixture using a suitable “C” or “O” type clamp. The clamp should be rated to hold at least 10x the fixture’s weight to ensure structural stability. Do not mount to surfaces with unknown strength, and ensure properly “rated” rigging is used when mounting fixtures overhead. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs. • When selecting installation location, take into consideration lamp replacement access (if applicable) and routine maintenance. • Safety cables MUST ALWAYS be used. • Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation.
Page 9
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
Using the AnyFi™ Wireless DMX Receiver In addition to the unbridled thrill you already received the first time you turned on your fixture, you’ll be delighted to know that your fixture is equipped to work seamlessly with our own Skywire™ 2.4GHz wireless DMX products, as well as W-DMX™ wireless products. Skywire™ AnyFi™ wireless DMX products feature 512 autoassigning frequencies in either 6 or 7 groups allowing multiple systems to run simultaneously in the same space, completely free of interference, with reliable wireless communication for over Universal Wireless DMX 1000 feet line-of-sight! Using the W-DMX™ wireless protocol in AnyFi™, you can expect the same outstanding wireless range, very easy setup, and leave any worries behind concerning loss of signal due to its built-in FHSS technology (Frequency Hopping Spread Spectrum). So first, if you would like to use Skywire™ wireless DMX protocol, you will need a wiCICLE® transmitter, Lightcaster™ transceiver, or any Blizzard Lighting controller with this type of built-in wireless transmitter. And if you plan on using W-DMX™ 2.4GHz wireless protocol, you will need a W-DMX™ transceiver to broadcast the signal from your controller, such as our Lightcaster W-DMX™.
Ready to move on? Well alrighty! IMPORTANT - If you are using Blizzard’s Lightcaster Any-Fi wireless transmitter in W-DMX compatibility mode along with DMX control software like our Eclipse DMX or Lucid products, you must set the MAB (Mark After Break) in the software to 30 microseconds (μS) to avoid potential signal timing issues. 1.) Set the Fixture to Receive Wireless Signal in the Control Panel
a.) Navigate the main menu to reach SET, press , then use the buttons until SIGN is displayed, then press again. Now use the buttons to highlight 2.4G (wireless mode), and press . 2.) Resetting The Wireless a.) Navigate the main menu to reach SET, press , then use the buttons until WIRE is displayed, then press again. b.) From here, you can use the buttons to highlight REST and press , select YES, then to reset the wireless setup. 3.) Select W-DMX™ or Skywire™ Modes a.) Make sure the device you are using to transmit signal with is powered on. b.) Navigate the main menu to reach SET, press , then use the buttons until WIRE is displayed, then press again. c.) Now use the buttons to highlight KEY, and press . d.) At this point, please note that every time you touch the button, the wireless LED status indicator changes between 4 colors (currently 3 are functional): • GREEN: W-DMX™ 2.4 GHz Receiver Mode • YELLOW: Skywire™ 7CH Receiver Mode (wiCICLE™ & LightCaster Compatible) • RED: Skywire™ 6CH Receiver Mode (AnyFi™ Transmitter Compatible) *Note: The top level BLUE channel mode currently has no function. e.) While the LED indicator is illuminated in GREEN (for W-DMX), YELLOW (for Skywire 7CH), or RED (for Skywire 6CH) press and hold the button for 1 second to confirm and save. Press and hold for 3 seconds to disconnect. For W-DMX™ connections, you should be done. The fixture will detect the signal! *For Skywire™ wireless connections, continue to Step 5 on the next page.
Page 10
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
4.) Successful W-DMX™ Connections
The LED status indicator will blink, then turn white if searching for a signal. When a signal connection is established, the LED on the fixture will be solid GREEN, if signal is lost the LED will flash RED. W-DMX™ Setup Examples: 1.) One transceiver with multiple receiver setups: a.) Power on all units. b.) On the receiving W-DMX fixtures, follow the previous instructions to pair them with the transmitting unit. 2.) Multiple transceiver setups, with multiple receivers; e.g. 3 groups consisting of a transceiver & receiver(s) named A, B, and C: a.) Turn power off of all units. b.) Group “A” gets powered on, then follow step 1 above. c.) Group “B” gets powered on, then follow step 1 above. d.) Group “C” gets powered on, then follow step 1 above. 5.) Skywire™ 6/7-Channel Modes: Selecting the Channel Group 1. After selecting either Skywire 2.4GHz Mode in Step 3 on the previous page, the fixture is ready and waiting for your input to select the frequency group to match that of your transmitting source. a.) Tap the button repeatedly to scroll through the channel groups: Top Menu LED Color
Mode
Channel LED Color
Skywire™ 6CH (AnyFi™ products only)
Information
CH1 CH2 CH3 CH4 CH5 CH6
These 6 color coded channels match perfectly with other AnyFi™ wireless products while using Skywire™ 6CH mode.
CH1 CH2 CH3 CH4 CH5 CH6 CH7
These channel numbers correspond to the “GROUP” settings on our LightCaster™ wireless DMX transceiver, and the colored channels match all wiCICLE™ and Skywire™ wireless products.
W-DMX Receive (G3 or G4)
Skywire™ 7CH (wiCICLE™ compatible)
b.) While your chosen group number/color is illuminated on the status LED, press and hold the button for 3 seconds. 2. The LED on the transmitter will blink RED slowly until communication is established with the receiver. The status LED on the receiving fixtures will be illuminated in the color of the group that it is set on until communication is established. 3. Once the clearest channel is auto-selected, the status LEDs will blink quickly on both the transmitter and receiver. NOTE: The color of the status LED DURING operation does not indicate channel group, instead it indicates whether the unit is transmitting or receiving. That’s It!
Page 11
Colorise™ Zoom RGBAW Manual Rev. B
© 2016 Blizzard Lighting, LLC
4. OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with the Colorise™ Zoom are accessed by using the control panel on the rear of the fixture. There are 4 control buttons below the LED display which allow you to navigate through the various control panel menus.
