Block Diagram Of Vcr Section

Transcript

27DV-S100 27DV-CS10 SERVICE MANUAL S81Z627DV-S10 TV/VCR/DVD COMBINATION Chassis No. B00A MODELS 27DV-S100 27DV-CS10 In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page » IMPORTANT SERVICE SAFETY PRECATION ....................................................................................... 2 » SAFETY PRECAUTIONS ........................................................................................................................ 6 » ELECTRICAL SPECIFICATIONS ............................................................................................................ 7 » LOCATION OF USER'S CONTROL ........................................................................................................ 8 » DISASSEMBLY AND REASSEMBLY ..................................................................................................... 12 » INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................. 16 » PRECAUTIONS IN REASSEMBLING ................................................................................................... 22 » FUNCTION OF MAJOR MECHANICAL PARTS .................................................................................... 23 » ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS .................................... 25 » ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY ..................................................................... 45 » TEST MODE OF DVD SECTION ........................................................................................................... 47 » TROUBLESHOOTING ........................................................................................................................... 50 » CHASSIS LAYOUT ................................................................................................................................. 72 » IC FUNCTION LIST OF DVD SECTION ................................................................................................ 74 » BLOCK DIAGRAM OF TV SECTION ..................................................................................................... 94 » BLOCK DIAGRAM OF VCR SECTION .................................................................................................. 96 » BLOCK DIAGRAM OF DVD SECTION ................................................................................................ 106 » OVERALL SCHEMATIC DIAGRAM ..................................................................................................... 108 » DESCRIPTION OF SCHEMATIC DIAGRAM ....................................................................................... 110 » PRINTED WIRING BOARD ASSEMBLIES .......................................................................................... 143 » REPLACEMENT PARTS LIST ............................................................................................................. 155 » PACKING OF THE SET ....................................................................................................................... 185 SHARP CORPORATION This document has been published to be used for after sales service only. 1The contents are subject to change without notice. 27DV-S100 27DV-CS10 IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines which follow: WARNING X-RADIATION AND HIGH VOLTAGE LIMITS 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. 3. Semiconductor heat sinks are potential shock hazards when the chassis is operating. 4. The chassis in this receiver has two ground systems which are separated by insulation material. The nonisolated (hot) ground system is for the +B voltage regulator circuit and the horizontal output circuit.The isolated ground system is for the low +B DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis. 1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation if the high voltage is as specified in the “High Voltage Check” instructions. It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in glass material. The important precaution is to keep the high voltage below the maximum level specified. 2. It is essential that servicepersonel have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically. 3. High voltage should always be kept at the rated value -no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also,under certain conditions, may produce radiation that exceeds specifications. 4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, thebrightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly. 5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry. 6. When trouble shooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage. 6.3A 125V CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 6.3A125V FUSE. SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.) 1. Note that the picture tube in this receiver employs integral implosion protection. 2. Replace with tube of the same type number for continued safety. 3. Do not lift picture tube by the neck. 4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely. 2 27DV-S100 27DV-CS10 IMPORTANT SERVICE SAFETY PRECAUTION (Continued) » Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor. AII check must be repeated with the AC line cord plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above are indicative of a potential shock hazard and corrective action must be taken before returning the instrument to the customer. BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard) Before returning the receiver to the user, perform the following safety checks. 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver. 2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. » Plug the AC cord directly into a 120 volt AC outlet, (Do not use an isolation transformer for this test). » Using to clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground. » Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor. AC VOLTMETER 1.5k ohm 10W 0.15µF TEST PROBE TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 SAFETY NOTICE For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards. Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement par ts which have special safety characteristics are identified in this manual; electrical components having such features are identified by “ å” and shaded areas in the Replacement Parts Lists and Schematic Diagrams. 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 3 27DV-S100 27DV-CS10 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë Ne peut effectuer la réparation qu’ un technicien spécialisé qui s’est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION 1. N’entreprendre aucune modification de tout circuit. C’est dangereux. 2. Débrancher le récepteur avant toute réparation. 3. Les déversoirs thermiques à semi-conducteurs peuvent présenter un danger de choc électrique lorsque le réceqteur est en marche. 4. Le châssis de ce récepteur a deux systèmes de mise à la terre qui sont séparés par un matériau isolant. Le système de mise à la terre non-isolée (chaud) est pour le circuit du régulateur de tension +B et le circuit de sortie horizontale. Le système de mise à la terre isolé est pour les basses tensions C. C. +B et le circuit secondaire du transformateur de haute tension. 6.3A 125V 1. Tout le personnel réparateur doit être instruit des instructions et procédés relatifs aux radiations X. Le tube-image, seule source de rayons X dons les téleviseurs transistorisés, n’émet pourtant pas de rayons mesurables si la haute tension est maintenue à un niveau préconisé dans la section “Vérification de la haute tension”. C’est seulement quand la haute tension est excessive que les rayons X peuvent entrer dans l’enveloppe du tube-image y compris le conducteur de verre. Il est important de maintenir la haute tension en-dessous du niveau spécifié. 2. Il est essentiel que le réparateur ait sous la main un voltmètre à haute tension qui doit être périodiquement étalonné. 3. La haute tension doit toujours être maintenue à la valeur de régime-et pas plus haute. L’opération à des tensions plus élevées peut entraîner une panne du tube-image ou du circuit à haute tension et, dans certaines conditions, peut entraîner une radiation dépassant les niveaux préscrits. 4. Quand le régulateur à haute tension fonctionne correctement, il n’y a aucun problème de radiation X. Chaque fois qu’un châssis couleurs est réparé, la luminosité doit être examinée bout en contrôlant la haute tension à l’aide d’un voltmètre pour s’assurer que la haute tension ne dépasse pas la valeur spécifiée et qu’elle soit correctement réglée. 5. Ne pas utiliser un tube-image autre que celui spécifié et ne pas effectuer de modifications déconseillées du circuit à haute tension. 6. Lors de la recherche des pannes et des mesures d’essai sur un récepteur qui présente une haute tension excessive, éviter de s’approcher inutilement du récepteur. Ne pas faire fonctionner le récepteur plus longtemps que nécessaire pour localiser la cause de la tension excessive. P R E C AU T I O N : P O U R L A PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE, REMPLACERLE FUSIBLEPAR UN FUSIBLE DE MEME TYPE 6.3-125V. REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE Lors de la réparation de ce systéme, supprimer la charge statique en branchant une résistance de 10 k en série a vec un fil isolé (comme une sonde d’essai) entre la mise à la terre du tube-image et le fil d’anodel. (Le corden d’alimentation doit être retiré de la prise murale.) 1. Il est à noter que le tube-image de ce récepteur est intégralement protégé contre l’implosion. 2. Par mesure de sécurité, changer le tube-image pour un tube du même numéro de type. 3. Ne pas lever le tube-image par son col. 4. Ne manipuler le tube-image qu’en porant des lunettes incassables et qu’après avoir déchargé totalement la haute tension. 4 27DV-S100 27DV-CS10 PRECAUTIONS A PRENDRE LORS DE LA REPARATION (Suite) » Toucher avec la sonde d’essai les pièces métalliques exposées qui présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson, etc.) et mesurer la chute de tension CA en-travers de la résistance. Toutes les vérifications doivent être refaites après avoir inversé la fiche du cordon d’alimentation. (Si nécessaire, une prise d’adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.) Tous les courants mesurés ne doivent pas dépasser 0,5 mA. Dans le cas contraire, il y a une possibilité de choc électrique qui doit être supprimée avant de rendre le récepteur au client. VERIFICATIONS CONTRE L’INCEN-DIE ET LE CHOC ELECTRIQUE Avant de rendre le récepteur à l’utilisateur, effectuer les vérifications suivantes. 1. Inspecter tous les faisceaux de câbles pour s’assurer que les fils ne soient pas pincés ou qu’un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur. 2. Inspecter tous les dispositifs de protection comme les boutons de commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux de résistance-capacité, les isolateurs mécaniques, etc. 3. S’assurer qu’il n’y ait pas de danger d’électrocution en vérifiant la fuite de courant, de la facon suivante: » Brancher le cordon d’alimentation directem-ent à une prise de courant de 120V. (Ne pas utiliser de transformateur d’isolation pour cet essai). » A l’aide de deux fils à pinces, brancher une résistance de 1,5 k 10 w atts en parallèle avec un condensateur de 0,15µF en série avec toutes les pièces métalliques exposées du coffret et une terre connue comme une conduite électrique ou une prise de terre branchée à la terre. » Utiliser un voltmètre CA d’une sensibilité d’au moins 5000 /V pour mesurer la chute de tension en tr avers de la résistance. Voltmètre CA 1.5k ohm 10W 0.15µF SONDE D'ESSAI AUX PIECES METALLIQUES EXPOSEES BRANCHER A UNE TERRE CONNUE 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 AVIS POUR LA SECURITE identifiées par la marque “ å “ et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques. Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d’origine. L’utilisation de pièces qui n’ont pas les mêmes caractéristiques que les pièces recommandées par l’usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents. De nombreuses pièces, électriques et mécaniques, dans les téléviseurs présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 5 27DV-S100 27DV-CS10 SAFETY PRECAUTIONS Precaution to be taken when replacing and servicing the Laser Pickup. PRODUIT LASER DE CLASSE 1 The product is a Class 1 Laser Product. However Laser component is capable of emitting radiation exceeding the limit for Class 1. It is important that following precautions are observed during servicing to protect your eyes against exposure to the laser beam. CLASS 1 LASER PRODUCT 1. When the cabinet is removed, interlock is defeated (if equipped), the power is turned on without a disk in position, Do not look into the pickup lens. 2. The laser power output of the pickup unit and replacement service parts are all factory pre-set before shipment. Do not attempt to re-adjust the laser pickup unit during replacement or servicing. 3. Under no circumstances stare into the pickup lens at any time. 4. C a u t i o n - U s e o f c o n t r o l s o r a d j u s t m e n t o r performance of procedures other than those specified herein may result in hazardous radiation exposure. (Back of product) » LASER SPECIFICATIONS Laser Diode Properties Material : AIGalnP Wave length DVD : 645~660nm CD : 770~810nm Emission Duration : Continuous Laser output : Max. 0.6 mW (Top View) DVD Unit CAUTION-WHEN OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. VARNONG-NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ STRÅLEN MED OPTISKA INSTRUMENT. ADVARSEL-VED ÅBNING. SE IKKE IND I STRÅLEN-HELLER IKKE MED OPTISKE INSTRUMENTER. VARO! AVATTAESSA OLET ALTTIINA. ÄLÄ TUIJOTA SÄTEESEEN ÄLÄKÄ KATSO SITÄ OPTISEN LAITTEEN LÄPI. VARNING-NÄR DENNA DEL ÄR ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ STRÅLEN GENOM OPTISKT INSTRUMENT. ADVARSE-NÅR DEKSEL ÅPNES. STIRR IKKE INN I STRÅLEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER. NOTE: Laser beam is emitted when this is open. Do not stare into the beam. Do not view the beam through any optical instrument, either. 6 27DV-S100 27DV-CS10 ELECTRICAL SPECIFICATIONS TV SECTION POWER INPUT: POWER RATING: PICTURE SIZE Width: Height: Depth: CONVERGENCE: SWEEP DEFLECTION: FOCUS: INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency: Sound IF Carrier Frequency: Color Sub-Carrier Frequency: AUDIO POWER OUTPUT RATING: SPEAKER Size: Voice Coil Impedance: VHF/UHF ANTENNA INPUT IMPEDANCE: TUNING RANGES VHF-Channels: UHF -Channels: CATV Channels: 120 V AC 60 Hz 165 W 37.8 cm 38.7 cm 37.5 cm Magnetic Magnetic Hi-Bi-Potential Electrostatic 45.75 MHz 41.25 MHz 42.17 MHz (Nominal) 3 W + 3 W (at 10% Distortion) 8 cm (3-1") 16 ohm at 400 Hz 75 ohm unbalanced 2 thru 13 14 thru 69 1,14 thru 125 (EIA, Channel Plan) VCR SECTION Format: Video Recording System: Number of Video Heads: Video Signal Standard: Tape Width: Tape Speed: Maximum Recording Time: Video Input: Audio Input: DVD SECTION Playback-compatible discs: Signal system: Operating Temperature: Storage Temperature: VHS Standard Rotary Two-Head Helical Scanning 4 pcs. NTSC Color System 12.7mm (1/2inch) (SP)33.35mm/sec (1.31 i.p.s) (LP)16.68mm/sec (0.66 i.p.s) Play back only (EP)11.12 mm/sec (0.44 i.p.s) (SP)120 min (with T-120) (EP)360 min (with T-120) 0.5 to 2.0 Vp-p, 75 ohm unbalanced -8 dB, 47k ohm unbalanced (0 dB-0.775 Vrms) DVD (regional code "1"/"ALL"), Video CD (NTSC), CD, DA, MP3, Music CD NTSC 5°C to 40°C (41°F to 104°F) -20°C to 60°C (-4°F to 140°F) Specifications are subject to change without prior notice. 7 27DV-S100 27DV-CS10 LOCATION OF USER'S CONTROL Front (TV/VCR controls) Cassette compartment VCR mode indicator |PLAY button POWER button Ë STOP/ »REC button EJECT button TAMPER PROOF indicator ÈREW (rewind) button PROGRAM TIMER indicator VOL + / – (UP/DOWN) buttons REC indicator CH ' / " (UP/DOWN) buttons POWER/WAKE-UP TIMER indicator FF è (fast forward) button Front (DVD controls) Sensor area for Remote Control DVD mode indicator OPEN-CLOSE button |ÈSKIP/REV (reverse) button |PLAY button SKIP/FWD (forward) è|button VIDEO / L-AUDIO-R terminals (Inside the cover) PHONES (Headphone jack) Ë STOP button Disc tray Ë Insert the headphones (not supplied) into the headphone jack to listen to audio. 8 27DV-S100 27DV-CS10 LOCATION OF USER'S CONTROL (Continued) Rear Video output terminal Video input terminal DVD OPTICAL DIGITAL output terminal DVD COAXIAL DIGITAL output terminal Audio input terminals Audio output terminals ANT/CABLE terminal (75Ω) 9 27DV-S100 27DV-CS10 LOCATION OF USER'S CONTROL (Continued) Remote Control Unit (Cover closed) CATV TV INPUT POWER DVD DVD SLOW SUBTITLE F.ADV ANGLE SKIP (REV) SKIP (FWD) STILL/PAUSE PLAY REV (reverse) FWD (forward) STOP ZOOM REPEAT DVD/TV MUTE DISPLAY CH '/", TR MTS FLASHBACK / VOL + / – CHANNEL SELECT buttons Ë Using Your Remote Control With Your unit After installing the batteries, press TV to switch to the TV mode. (If you can change the channel of the TV by pressing CH '/" or CHANNEL SELECT buttons,you are in TV mode.) Loading the Batteries Ë Before using the unit, prepare the Remote Control. To use the Remote Control, insert batteries first. Insert the batteries Pull up Battery Cover + – – + • With your thumbnail, pull up the slit as indicated by the arrow to remove the back cover. Insert two batteries (size “AA”). Be sure to match the battery ±/— terminals with the ±/— marks inside the compartment. 10 27DV-S100 27DV-CS10 LOCATION OF USER'S CONTROL (Continued) Remote Control Unit (Cover open) DVD DVD AUDIO SUBTITLE ANGLE SET UP RETURN MENU DVD SET DISC MENU CURSOR VIRTUAL DVD PROGRAM TITLE NUMBER buttons DIRECT MEMORY GAMMA CLEAR S.PICTURE VCR VCR CONFIRM COUNTER RESET SLOW PROG. PAUSE/STILL REC (record) T.PROOF TAPE SPEED FF (fast forward) REW (rewind) DPSS ON/OFF PLAY STOP 11 27DV-S100 27DV-CS10 DISASSEMBLY AND REASSEMBLY 1. Remove the 16 rear cover fixing screws and detach the rear cover. 2. Take out the anode cap, CRT PWB, connectors OO, K and M, coating earth, speaker connectors SE, connector DC and others. 3. Remove the 2 main chassis fixing screws and take out the main chassis. 4. Remove the 5 fixing screws from the sub-chassis for the VCR power/deflection PWB and detach this sub-chassis. 5. Remove the 5 VCR shielding case fixing screws and detach the shielding case. 6. Remove the 4 cassette housing fixing screws and detach the cassette housing. 1 2 OO OO DC K DC SE M 3 4 5 6 12 27DV-S100 27DV-CS10 7. Remove the 2 mechanism chassis bracket fixing screws and the head amplifier shielding case fixing screw. 8. Remove the 3 mechanism chassis fixing screws and detach the mechanism chassis from the main PWB. 9. Remove the 2 DVD mechanism unit reinforcement fixing screws and detach this reinforcement. 10.Remove the 4 DVD mechanism unit fixing screws and detach the DVD mechanism unit. 11.Remove the 1 main PWB fixing screws and detach the main PWB. 12.Remove the 1 TV signal PWB fixing screw and detach the TV signal PWB. 13.Remove the 2 TV power PWB fixing screws and detach the TV power PWB. » DVD section 14.Remove the 5 DVD shielding case fixing screws and detach the DVD shielding case. 15.Undo the 4 hooks from the chassis for the DVD main and sub PWBs, and detach this chassis. 16.Remove the 4 DVD main PWB fixing screws and detach the DVD main PWB. 17.Remove the DVD sub PWB fixing screw, undo the hook and detach the DVD sub PWB. 18.Finally remove the 4 DVD mechanism fixing screws and detach the DVD mechanism. 7 8 8 10 9 14 14 16 17 13 15 11 18 12 13 27DV-S100 27DV-CS10 REPLACEMENT OF MAIN PARTS 1. Remove the mechanism with angle from the set (refer to 17 on PARTS LIST (See page 183)). 2. It is in such cases as the thin driver, and it is pushed in slowly, and a tray is drawn in the arrow direction the slide rack on the left of the base chassis. 3. Take out disk. Front Side 1. After setting the mechanism chassis to the angle state, ground it to prevent the electrostatic discharge damage of the pickup. 2. Remove the DVD shield (lower) 5 (refer to the illustration on PARTS LIST (See page 183)). 3. Remove the DVD main PWB unit 35 , and loosen the 4 screws 56 to remove the DVD main PWB unit 35 . (Pickup relay FFC isn’t removed.) (refer to the illustration on PARTS LIST (See page 183)) 4. Remove screws fixing the base chassis (located at the back right and at front left when facing the set). 5. With the pickup FFC connected, turn over the base chassis and short (solder) two short lands on the pickup interface PWB in order to prevent the electrostatic discharge damage of the pickup. 6. Remove the pickup FFC from the main PWB. 7. Remove the pickup FFC from the pickup interface PWB. 8. Remove the traverse mounting screws to remove the traverse chassis ass’y. Note: After assembly and wiring, remove the solder joint of the short land. If short-circuited, a disk is not played back. Pickup FFC Traverse Fixing Screw Sled Motor Lead Wire Loading Motor Lead Wire Since the pickup optical axis and turntable inclination of DVD are adjusted with higher accuracy than of CD/MD, make a replacement as a mechanism service chassis ass’y (refer to Parts List). Pickup FFC Pickup interface PWB Short Land 14 27DV-S100 27DV-CS10 For servicing the TV’s component units, undo the lead dressing holders and place the main chassis upright as shown below. Connect necessary leads for quick servicing. OO FRONT SC SA AR SA DC SB WA SB OC DA DB DE AR SE ZA DF DB DC GBN XB ZA SE BA XB OR DD DA DF PU GBN N(H) XC GA XC EB M DC M OO SE EB K DC SC OO DD OC WA BA GA N K Remove the four screws from the cathode ray tube, and detach the cathode ray tube (weighing 35 kg or so). » The cathode ray tube has a high-tension static charge and a high vacuum. Handle it with enough care on the following occasions. Get the air vent tip cracked to let in air. ~ ~ ~ For disposal of the cathode ray tube 1) The high-voltage electrode, which is covered with the anode cap atop the cathode ray tube, may have a high-tension static charge. Before detaching the anode cap, be sure to get this electrode fully discharged. 2) The cathode ray tube has a high vacuum inside. Crack the tip of the air vent on the neck socket of the cathode ray tube in order to get the tube out of vacuum. 15 ~ 27DV-S100 27DV-CS10 INSTALLATION AND SERVICE INSTRUCTIONS Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic screwdriver or TV alignment tools. (2) Before performing adjustment, TV set must be on at least 15 minutes. CIRCUIT PROTECTION HIGH VOLTAGE CHECK The receiver is protected by a 6.3A fuse (F701), mounted on PWB-A, wired into one side of the AC line input. High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows: 1. Connect an accurate high voltage meter between ground and anode of Picture tube. 2. Operate receiver for at least 15 minutes at 120V AC line voltage, with strong air signal or properly tuned in test signal. 3. Set to Service mode on, “Mute” and bus data 1(Ymute on). 4. The voltage should be approximately 29.2kV (at zero beam). If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test, “Mute” and bus data “0” (Y-mute off). X-RADIATION PROTECTOR CIRCUIT TEST After service has been performed on the horizontal deflection system, high voltage system, or +B system, test the X-Radiation protector circuit to ascertain proper operation as follows: 1. Apply 120V AC using a variac transformer for accurate input voltage. 2. Allow for warm up and using the remote controller, set the brightness level and contrast level to maximum. 3. Check the voltage of test point TP653. (It’s voltage should be about 11.1V DC.) 4. Apply external 14.5V DC at TP653 by using an external DC supply. The increased voltage will cause the horizontal oscillator to stop and the TV to shut off. 5. To re-start the oscillator, remove the external DC power supply and short together TP651 and TP652. Once the TV set operates normally again, remove the short between TP651 and TP652. 16 27DV-S100 27DV-CS10 The R-series SHARP TV/VCR COMBINATION have most of the analog setup adjustments eliminated. Coil and variable resistor adjustments are now performed digitally by using the remote controller or set’s volume and channel change function buttons. Note: There are still a few analog adjustments in the R-series such as 120V adjust, focus, master screen voltage and coils in the picture I/F detector circuit. Follow the steps below, whenever service adjustment is required. See “Table-B” to determine, if service adjustments are required. 1. Service mode 3. Data number selection Before putting unit into the service mode, check that customer adjustments are in the normal mode, use the reset function in the video adjust menu to ensure customer controls are in their proper (reset) position. Press the volume up or down button to adjust the data number in the upper right hand side of the screen. To enter the service mode Plug in a television set, during push S2507 (CH-up). When successfuly entered, the service mode will be displayed as shown in Figure A. To exit service mode Turn off the power or unplug the set. 2. Adjustment Item selection Once in the service mode, press the channel up or channel down button on the remote controller or at the set (Table-A). Select the item you wish to adjust. Figure A. 17 27DV-S100 27DV-CS10 ITEM SUB COTRAST(*1) TINT (*1) SUB COLOR (*1) BRIGHTNESS (*1) SHARPNESS V-POSITION (*1) H-POSITION (*1) R CUT-OFF (*1) G CUT-OFF (*1) B CUT-OFF (*1) G GAIN (*1) B GAIN (*1) Y-γ CURVE VSM PHASE APACON PEAK f0 DC RESTRATION RATE DC RESTRATION LIMIT BLACK STRETCH POINT APL VS BPS B.L.C DYNAMIC ABL POINT DYNAMIC ABL GAIN ABL POINT ABL GAIN Y-DL TOF-Q VSM GAIN OSD SL C-DECODE DVD BR-OFF PICTURE HEIGHT V-LINEARITY V-S CORRECTION PICTURE WIDTH E-W PARABOLA E-W CORNER TRAPEZIUM AGC Y-MUTE ENERGY SAVE TEXT BOX TEXT PICTURE CCD LEVEL OPTION (VCR) OPTION (TV) MTS INPUT LEVEL MTS VCO MTS FILTER WIDE BAND DETECT SPECTRAL DETECT H COMP V COMP CCD POSITION OSD DISPLAY PICTURE TINT COLOR BRIGHT SHARP V POSITION H POSITION R CUT-OFF G CUT-OFF B CUT-OFF G GAIN B GAIN Y-γ CURVE VSM PHASE APA PEAK f0 DC REST DC REST LMT BLK STRETCH APL VS BPS B.L.C DY ABL POINT DY ABL GAIN ABL POINT ABL GAIN Y-DL TOF-Q VSM GAIN OSD SL C-DECODE DVD BR-OFF V AMP V-LINEARITY V-S CORRECT H AMP E-W PARABOLA E-W CORNER TRAPEZIUM AGC MUTE ENERGY SAVE TEXT BOX TEXT PICTURE CCD LEVEL OPTION (VCR) OPTION (TV) INPUT LEVEL MTS VCO FILTER WIDE BAND SPECTRAL H COMP V COMP CCD POSITION INITIAL 20 30 18 55 15 95 17 64 64 64 64 64 00 01 01 21 00 03 01 01 04 04 03 03 01 04 01 00 161 30 22 22 40 30 19 18 55 01 00 21 8 20 04 39 31 07 37 30 35 22 03 03 38 RANGE 00 - 31 00 - 47 00 - 31 00 - 95 00 - 47 00-127 00 - 31 00-255 00-255 00-255 00-127 00-127 00 - 03 00 - 03 00 - 07 00 - 63 00 - 03 00 - 07 00 - 03 00 - 01 00 - 07 00 - 07 00 - 07 00 - 07 00 - 01 00 - 07 00 - 03 00 - 01 00-255 30 - 70 00-127 00 - 31 00 - 63 00 - 63 00 - 63 00 - 31 00-127 00 - 01 00 - 02 00 - 63 00 - 31 00 - 80 00 - 20 00-255 00-127 00 - 15 00 - 63 00 - 63 00 - 63 00 - 63 00 - 07 00 - 07 00 - 63 SETTING DATA Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Fix at "8" Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Fix at "03" Fix at "02" Fix at "01" Fix at "07" Fix at "02" Fix at "00" Fix at "01" Fix at "00" Fix at "06" Fix at "03" Fix at "07" Fix at "04" Fix at "01" Fix at "04" Fix at "02" Fix at "00" Fix at "153" Fix at "50" Adjustment is required of each set. Adjustment is required of each set. Fix at "47" Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Fix at "01" 00=NORMAL, 01=NO-Y, 02=NO-VERTICAL Fix at "21" Adjustment is required of each set. Fix at "20" Fix at "10" Fix at "39" Fix at "127" Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Adjustment is required of each set. Fix at "03" Fix at "03" Fix at "38" (*1) Set the adjustment value to tuner input instead of the adjustment at DVD input (play). Table-A PART REPLACED ADJUSTMENT NECESSARY IC2001 X IC401 X IC2003 X CRT X NOTE UNNECESSARY Data is stored in IC2003. The adjustment is needed to compensate for characteristics of parts including IC401. Initial setting values are written from IC2001. Adjust for best results. Adjust items related to picture tube only. Table-B 18 27DV-S100 27DV-CS10 Ë SERVICE ADJUSTMENT Screen Adjustment Brightness Adjustment 1. Select a good local channel. 2. Make sure the customer brightness control is set to center position. 3. Enter the service mode and select the service adjustment item "BRIGHT". 4. Adjust "BRIGHT" data value to obtain normal brightness level. 1. Select a good local channel. 2. Enter the service mode and select the service adjustment item "COLOR" and set the data value to "0" to set the color level to minimum. You may skip this step, if you selected a B/W picture or monoscope pattern. 3. Select service adjustment item "MUTE" and adjust the data value to "1", this turns off the luminance signal (Y-mute). 4. Adjust the master screen control until raster darkens to the point where raster is barely seen. 5. Adjust service adjustments item "R-CUT OFF" red "G-CUT OFF" green and "B-CUT OFF" blue to obtain a good grey scale with normal whites at low brightness level. 6. Select the service adjustment item "MUTE" and reset data to "0". Select service adjustment item "COLOR" and reset data to obtain normal color level. Vertical Phase Adjustment 1. Receive a good local channel. 2. Enter the service mode and select "V-POSITION". 3. Adjust data value so that picture is approximate center. Vertical-Size Adjustment 1. Receive a good local channel. 2. Enter the service mode and select "V-AMP". 3. While observing the top and bottom of the screen, adjust the data value to proper vertical size. White Balance Adjustment 1. Select a good local channel. 2. Enter the service mode and select the service adjustment item "COLOR" and set to "0" (minimum color). "COLOR" does not have to be adjusted if you selected a B/W picture or monoscope pattern. 3. Alternately adjust the service adjustment data of "G GAIN" and "B GAIN" until a good grey scale with normal whites is obtained. 4. Select the service adjustment item "COLOR" and adjust data to obtain normal color level. Side Pincushion Adjustment 1. Receive a good local channel or crosshatch pattern signal. 2. Set to standard setting mode. 3. Enter the service mode and select "E-W PARABOLA". 4. Adjust the data so that the outermost line on the screen be straight. Corner Distortion Adjustment 1. Receive a good local channel or crosshatch pattern signal. 2. Set to standard setting mode. 3. Enter the service mode and select "E-W CORNER". 4. Adjust the data so that the vertical lines should be straight. Picture Adjustment 1. Select a good local channel. 2. Make sure the customer picture control is maximum. 3. Enter the service mode and select the service adjustment item "PICTURE". 4. Adjust the data value to achieve normal contrast range. Trapezoidal Distortion Adjustment 1. Receive a good local channel or crosshatch pattern signal. 2. Set to standard setting mode. 3. Enter the service mode and select "TRAPEZIUM". 4. Adjust the data so that the leftmost and rightmost vertical lines are parallel to each other. Tint Adjustment 1. Select a good local channel. 2. Set customer tint control to center of it’s range. 3. Enter the service mode and select the service adjustment item "TINT". 4. Adjust "TINT" data value to obtain normal flesh tones. Horizontal Position Adjustment Color Adjustment 1. Receive a good local channel or crosshatch pattern signal. 2. Set to standard setting mode. 3. Enter the service mode and select "H-POSITION". 4. Adjust so that the left and right overscans are equal to each other. 1. Select a good local channel. 2. Make sure the customer color control is set to center position . 3. Enter the service mode and select the service adjustment item "COLOR". 4. Adjust "COLOR" data value to obtain normal color level. 19 27DV-S100 27DV-CS10 Horizontal Size Adjustment 1. Receive a good local channel or crosshatch pattern signal. 2. Set to standard setting mode. 3. Enter the service mode and select "H-AMP". 4. Adjust the data to obtain the best horizontal size. Caption Position Adjustment (Horizontal) 1. Receive a good local channel. 2. Enter the service mode and select "TEXT BOX". 3. A black text box appears on the screen. (see Figure B below) 4. Adjust the data value so that text box is positioned in the center of the screen. White Balance Adjustment of Component Signal Input 1. Feed the B/W pattern signal via the component signal input from signal generator. 2. Set "Y-MUTE" bus data to "01" to get the Y signal mute. 3. Select a luminance-short gun, and adjust the bus data of "R CUT-OFF", "G CUT-OFF" and "B CUT-OFF" to have the luminance at the white level. 4. Adjust the "G GAIN" and "B GAIN" setting to obtain the specified white level. Sub-brightness Adjustment of Component Signal Input 1. Feed the B/W pattern signal via the component signal input from signal generator. 2. Make sure the customer brightness control is set to center position. 3. Enter the service mode and select "BRIGHT". 4. Adjust the data value to obtain normal brightness level. 20 27DV-S100 27DV-CS10 Ë MTS ADJUSTMENT Separation Adjustment (for VCR tuner) MTS Level Adjustment (for TV tuner) 1. Connect the rms voltmeter to pin (22) of IC3601 (or negative (-) side of C1321). 2. Receive the following composite stereo signal 1. Composite stereo signal: 30% modulation, left channel only, noise reduction on, 300Hz. 3. Adjust R3601 to become the output level as the minimum. 4. Receive the following composite stereo signal 2. Stereo signal: 30% modulation, left channel only , noise reduction on, 3kHz. 5. Adjust R3612 to become the output level as the minimum. 6. Take the above steps 1 thru 5 again for fine adjustment. 1. Receive the following monaural signal. Monaural signal: 300Hz, 245mVrms. 2. Connect the rms voltmeter to pin (39) of IC3001. 3. Enter the service mode and select "INPUT LEVEL". 4. Adjust the data so that the rms voltmeter reads 490 +10/-10mVrms. MTS VCO Adjustment (for TV tuner) 1. Keep the unit in no-signal state. 2. Connect the frequency counter to pin (39) of IC3001. 3. Connect a capacitor (100uF, 50V) between positive (+) side of C3005 and ground. 4. Enter the service mode and select "MTS VCO". 5. Adjust the data so that the frequency counter reads 62.94 +0.72/-0.75kHz. Filter Adjustment (for TV tuner) 1. Feed the following stereo pilot signal to pin (14) of IC3001. Stereo pilot signal: 9.4kHz, 600mVrms. 2. Enter the service mode and select "FILTER". 3. Adjust the data until "OK" appears in position on the screen. Make sure the "OK" is displayed almost at the center of the data range. Separation Adjustment (for TV tuner) 1. Connect the rms voltmeter to pin (39) of IC3001. 2. Receive the following composite stereo signal 1. Composite stereo signal: 30% modulation, left channel only, noise reduction on, 300Hz. 3. Enter the service mode and select "WIDE BAND". 4. Adjust the data until the AC voltage reading of the rms voltmeter is minimum. 5. Receive the following composite stereo signal 2. Stereo signal: 30% modulation, left channel ony, noise reduction on, 3kHz. 6. Enter the service mode and select "SPECTRAL". 7. Adjust the data until the AC voltage reading of the rms voltmeter is minimum. 8. Take the above steps 1 thru 7 again for fine adjustment. MTS Level Adjustment (for VCR tuner) 1. Receive the following monaural signal. Monaural signal: 300Hz, 245mVrms. 2. Connect the rms voltmeter to pin (22) of IC3601 (or negative (-) side of C1321). 3. Adjust R3614 to become the output level as 490 +10/-10mVrms. 21 27DV-S100 27DV-CS10 PRECAUTIONS IN REASSEMBLING INSTALLING THE CASSETTE HOUSING When the cassette housing is installed on the mechanism, the initial setting is essential condition. There are two initial setting methods, namely electrical and mechanical. 1. Electrical initial setting So as to perform initial setting of mechanism execute the Step 1 of Installation of cassette housing. After ascertaining the return to the initial setting position (*1) install the cassette housing. (Conditions: When mechanism and PWB have been installed) 2. Mechanical initial setting Feed the pulley feed gear of loading motor with screw driver. After ascertaining the return to the initial set position (*1) install the cassette housing in the specified position. (This method is applied only for the mechanism.) Pulley feed gear Casecon drive gear Screwdriver Drive angle of cassette housing Tint mark (*1) Installing the mechanism on PWB Parts which need particular care Lower vertically the mechanism, paying attention to the mechanism edge, and install the mechanism with due care so that the parts are not damaged. So as to fix the mechanism to the main PWB install two housings. (Fit the antenna cover to one of them. For other, fix the vicinity of loading motor and solder joint side of main PWB.) Connect again the FFC cable (AA-MH, AD-ME, AH-MZ) between the mechanism and the main PWB. When installing the mechanism chassis on the PWB unit, take care so as to prevent deformation due to contact of mechanism chassis with REC TIP SW. AE CONNECTOR END SENSOR REC TIP SW AD CONNECTOR START SENSOR AL CONNECTOR 22 27DV-S100 27DV-CS10 FUNCTION OF MAJOR MECHANICAL PARTS (TOP VIEW) 15 17 10 18 19 14 1 9 2 11 7 5 3 12 8 16 6 No. 13 4 Function No. Function 1 Full erase head 11 Reverse guide lever ass’y 2 Supply pole base ass’y 12 Casecon drive gear 3 Tension arm ass’y 13 Take-up reel disk 4 Idler wheel ass’y 14 Pinch roller lever ass’y 5 Pinch drive lever ass’y 15 Drum ass’y 6 Supply reel disk 16 Loading motor 7 Supply main brake ass’y 17 Drum motor 8 Take-up main brake ass’y 18 Take-up pole base ass’y 9 Pinch drive cam 19 Impedance roller ass’y 10 A/C Head ass’y 23 27DV-S100 27DV-CS10 FUNCTION OF MAJOR MECHANICAL PARTS (BOTTOM VIEW) 21 22 19 26 20 12 23 No. 24 Function No. Function 12 Casecon drive gear 22 Reel belt 19 Slow brake 23 Clutch lever 20 Master cam 24 Limiter pulley ass'y 21 Capstan D.D. motor 26 Shifter 24 27DV-S100 27DV-CS10 ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS The explanation given below relates to the on-site general service (field service) but it does not relates to the adjustment and replacement which need high-grade equipment, jigs and skill. For example, the drum assembling, replacement and adjustment service must be performed by the person who have finished the technical courses. MECHANISM CONFIRMATION ADJUSTMENT JIG So as to perform completely the mechanism adjustment prepare the following special jigs. So as to maintain the initial performance of the machine the maintenance and check are necessary. Utmost care must be taken so that the tape is not damaged. If adjustment needs any jig, be sure to sue the required jig. 1. Torque Cassette Meter JiGVHT-063 CZ JiGTG0090 CM JiGTG1200 CN JiGTH0006 AW This cassette torque meter is used for checking and adjusting the torque of take-up for measuring tape back tension. 2. Torque Gauge 3. Torque Gauge Head 4. Torque Driver JiGTD1200 CB Master Plane Jig and 5. Reel Disk Height Adjusting Jig JiGRH0002 BR JiGMP0001 BY JiGSG2000 BS JiGSG0300 BF Pinch pressing force measuring jig JiGTDP003 BK Hex Wrench (1.2mm) JiGHW0012 AE Hex Wrench (1.5mm) JiGHW015 AE These Jigs are used for checking and adjusting the torque of takeup and supply reel disks. When fixing an y part to the threaded hole using resin with screw, use the jig. (Specified torque 5 kg) These Jigs are used for checking and adjusting the reel disk height. There are two gauges used for the tension measurements, 300 g and 2.o kg. 6. Tension Gauge 7. This Jig is used with the tension gauge. Rotary transformer clearance adjusting jig. This Jigs are used for loosening or tightening special hexagon type screws. 8. 9. Reverse guide height adjusting box driver This Jig is used for height adjustment of the reverse guide (for reverse guide height adjustment). JiGDRiVER11055 AR 25 27DV-S100 27DV-CS10 No. Jig Item Part No. Code Configuration Remarks These tapes are especially used for electrical fine adjustment. Video 10. Alignment Tape VROATSV CD VROEBZCS Audio Hi-Fi Audio Track 525 Monoscope 7k — 58µm NTSC Color Bar 1k — 58µm 525 Monoscope 1k — 19µm JiGDRiVERH-4 AP This screwdriver is used for adjusting the guide roller height. X value adjustment gear type screw driver JiGDRiVER-6 BM For X value adjustment. Reverse Guide Height Adjusting JiGRVGH-F18 BU This Jig is used for height adjustment of the reverse guide. 11. Guide roller height adjustment drive 12. 13. 26 27DV-S100 27DV-CS10 MAINTENANCE CHECK ITEMS AND EXECUTION TIME Perform the maintenance with the regular intervals as follows so as to maintain the quality of machine. Ref.No. Parts Maintained 500 1000 1500 2000 hrs. hrs. hrs. hrs. Possible symptom encountered Abnormal rotation or significant vibration requires replacement. 49 Guide roller ass’y — Sup guide shaft 19 Reverse guide 7,8 Slant pole on pole base 58 Full erase head Colour and beating 59 A/C head Small sound or sound distortion Poor S/N ratio, no colour Poor flatness of the envelope with alignment tape No tape running, uneven colour No tape running, tape slack No tape running, tape slack, no fast forward/ rewind motion Lateral noises Head occasionally blocked 63 Upper and lower drum ass’y 61 Capstan D.D. motor 12 Pinch roller 34 Reel belt 1 Tension band ass’y Screen swaying 60 Loading motor Cassette not loaded or unloaded 46 Idler ass’y 48 Limiter pulley Clean tape contact part with the specified cleaning liquid. Clean tape contact area with the specified cleaning liquid. Clean rubber and rubber contact area with the specified cleaning liquid. No tape running, tape slack Tape slack 24,25 Supply/take-up main brake levers 26 Remarks Replace the roller of the cleaner when it wears down. Just change the AHC roller assembly for new one. AHC (Automatic Head Cleaner) NOTE : Part replacement. : Cleaning : Apply grease Cleaning liquid Industrial ethyl alcohol * This mechanism does not need electric adjustment with variable resistor. Check parts. If any deviation is found, clean or replace parts. Video head cleaning procedure 1. Apply one drop of cleaning liquid to the cleaning paper with the baby oiler. 2. Gently press the cleaning paper against the video head to fix your finger, and move the upper drum so that each head is passed to and for 5 times (do not move the cleaning paper). 3. Wipe with the dry cleaning paper. Rotate the upper drum with one hand. Notes : • Use the commercially available ethanol of Class 1 as cleaning liquid. • Since the video head may be damaged, do not move up and down the cleaning paper. • Whenever the video head is cleaned, replace the cleaning paper. • Do not apply this procedure for the parts other than the video head. Gently press the cleaning paper to fix with your finger, and rotate the upper drum to clean. Move to and for 5 times for each head. (Do not move the cleaning paper.) Parts Code ZPAPRA56-001E ZOiLR-02-24TE 27 Description Cleaning Paper Babe Oiler (Spoit) 27DV-S100 27DV-CS10 Notes: 1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care. 2. Misengagement of teeth of casecon drive gear and drive angle gear causes malfunction. (The cassette cannot be set, load and ejection are repeated). 3. In the case when you use the magnet screw driver, never approach the magnet driver to the A/C head, FE head, and drum. 4. When installing or removing, take care so that the cassette housing control and tool do not contact the guide pin or drum. 5. After installing the cassette housing control once perform cassette loading operation. REMOVING AND INSTALLING THE CASSETTE HOUSING • Removal 1. In the cassette removing mode, remove the cassette. 2. Unplug the power cord. 3. Remove in the following numerical order. a) Remove two screws 1. b) Slide and pull up the cassette housing control. 1 TO RUN A TAPE WITHOUT THE CASSETTE HOUSING CONTROL ASSEMBLY 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Figure 1-1. • Reassembly 1. Before installing the cassette housing control, shortcircuit R7057 and JUMPER:420 provided on the main PWB, prug in the power cord, and then press the STOP/EJECT button. The casecon drive gear turns and stops when the positioning mark appears. Engage two teeth of casecon drive gear with the three teeth of casecon drive angle gear, and set on the mechanism chassis as shown below. Remove the full-surface panel. Short-circuit R7057 and JUMPER:420. Plug in the power cord. Turn off the power switch. (The mechanism moves to the cassette mounting position.) Open the lid of a cassette tape by hand. Hold the lid with two pieces of vinyl tape. Set the cassette tape in the mechanism chassis. Stabilize the cassette tape with a weight (500g) to prevent floating. Turn on the power switch. Perform running test. After running test, once turn off the power to let the mechanism move to the cassette mounting position, then remove the cassette. 500g Weight to prevent float (500g) Casecon drive gear Mechanism chassis Figure 1-3. Casecon drive angle gear Note: The weight should not be more than 500g. To take out the cassette tape. 1. Turn off the power switch. 2. Take out the cassette tape. Figure 1-2. 2. Install in the reverse order of removal. 28 27DV-S100 27DV-CS10 3. After checking the reel disk height, wind the tension band ass'y around the reel disk, and insert into the hole of tension arm ass'y. 4. Assemble the Supply main brake ass'y. Notes: 1. When installing the reel disk, take due care so that the tension band ass'y is not deformed and grease does no adhere. 2. Do not damage the Supply main brake ass'y. Be careful so that grease does not adhere to the brake surface. REEL DISK REPLACEMENT AND HEIGHT CHECK • 1. 2. 3. 4. Removal Remove the cassette housing control assembly. Pull the tension band out of the tension arm ass'y. Remove the Supply/Take-up main brake ass'y. Open the hook at the top of the reel disk, and remove the reel disk. Note: Take care so that the tension band ass'y and main brake ass'y (especially soft brake) are not deformed. Tension arm ass'y • Reassembly (Take-up reel disk) 1. Clean the reel disk shaft and apply grease (SC-141) to it. 2. Align the phase of the reel disk to that of the reel relay gear and to install a new take-up reel disk onto the shaft. 3. Check the reel disk height and reassemble the take-up main brake ass'y. Note: 1. Take care so that the Take-up main brake ass'y is not damaged. Take care so that grease does not adhere the brake surface. 2. After reassembly, check the video search rewind back tension (see page 32), and check the brake torque (see page 34). Take-up main brake ass'y Supply main brake ass'y Tension band ass'y Supply reel disk Take-up reel disk • Height checking and adjustment Note: 1. Set the master plane with due care so that it does not contact the drum. 2. When putting the master plane, shift the reverse guide a little in the loading direction. Care must be taken since excessive shift results in damage. Master plane Reverse guide Figure 1-4. Note: When the tension band ass'y is pressed in the direction of the arrow for removal, the catch is hard to be deformed. Supply reel disk Cassette lock release shaft Take-up reel disk Position pin Figure 1-6. Figure 1-5. Note: Check that the reel disk is lower than part A but higher than part B. If the height is not correct, readjust the reel disk height by changing the poly-slider washer under the reel disk. • Problems caused by maladjustments 1. Tapes may get scratched. • Reassembly (Supply reel disk) 1. Clean the reel disk shaft and apply grease (SC-141) to it. 2. Match the phases of reel disk and reel relay gear, and set the new reel disk. 29 27DV-S100 27DV-CS10 Note: Whenever replacing the reel disk, perform the height checking and adjustment. Reel disk height adjusting jig Master plane 10 ± 0.2mm Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement. 5. CHECKING AND ADJUSTMENT OF TAKE-UP TORQUE IN REWIND MODE Mechanism chassis Reel disk A • Remove the cassette housing control assembly. B • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn on the power. Reel disk Figure 1-7. CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN FAST FORWARD MODE • Setting 1. Set a torque gauge to zero on the scale. Place it on the supply reel disk. 2. Press the rewind button. 3. To calculate the remaining capacity, slowly rotate the take-up reel disk, and then shift it into the rewind mode. • Remove the cassette housing control assembly. • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn on the power. • Checking 1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CCW direction. 2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm). • Setting 1. Set a torque gauge to zero on the scale. Place it on the take-up reel disk. 2. Press the FF button. 3. To calculate the remaining capacity of the play back mode, slowly rotate the supply reel disk, and then shift it into the forward mode. Torque gauge 30mN·m (306gf·cm) or more • Checking 1. Turn the torque gauge slowly (one rotation every 2 to 3 seconds) by hand in the CW direction. 2. Make sure that the indication of torque gauge is not less than 30mN·m (306gf·cm). CCW The gauge is held at its maximum value. (Red mark) Torque gauge Supply reel disk CW 30mN·m (306gf·cm) or more Idler ass'y The gauge is held at its maximum value. (Red mark) Idler ass'y Figure 1-9. • Adjustment 1. If the rewind winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, rewind again, and check the winding-up torque. 2. If the winding-up torque is still out of range, replace the drive belt. • Problems caused by maladjustments 1. Tapes may fail to be wound up near the REW end. Figure 1-8. • Adjustment 1. If the FF winding-up torque is less than the specified value, clean the capstan D.D. motor pulley, drive belt, and limiter pulley with cleaning liquid, and check again. 2. If the torque is less than the set value, replace the reel belt. • Problems caused by maladjustments 1. Tapes may fail to be wound up near the FF end. 30 27DV-S100 27DV-CS10 Notes: 1. Hold the torque gauge by hand so that it is not moved. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement. CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN VIDEO SEARCH REWIND MODE • Remove the cassette housing control assembly. CHECKING AND ADJUSTMENT OF TAKEUP TORQUE IN RECORD/PLAYBACK MODE • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn on the power. • Remove the cassette housing control assembly. • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord. • Turn off the power switch. (The mechanism moves to the cassette mounting position.) • Open the cassette torque meter lid, and fix it with tape. • Load the cassette torque meter into the unit. • Put the weight (500g) on the cassette torque meter. • Turn on the power switch. • Press the picture record button, and set EP picture record mode (x3). • Setting Press the playback button and rewind button to set the video search rewinding mode. • Checking Place the torque gauge on the supply reel disk, and turn it counterclockwise very slowly (one rotation every 1 to 2 seconds) and check that the torque is within the set value 14.0 ± 3.9mN⋅m. (144 ± 40gf⋅cm) Torque gauge Set value EP6.9 ± 2.5mN·m (70 ± 25gf·cm) CCW 500g Cassette torque meter Supply reel disk Figure 1-10. Figure 1-11. • Checking 1. Make sure that value is within the setting 6.9 ± 2.5mN·m (70 ± 25gf·cm). 2. The winding-up torque fluctuates due to variation of rotation torque of limiter pulley ass'y. Read the center value of fluctuation as setting. 3. Set the EP record mode (x3) and make sure that the winding-up torque is within setting. Note: Surely put the torque gauge on the reel disk to measure. If the torque gauge is raised, accurate measurement is impossible. • Adjustment If the rewinding playback winding-up torque is not within the setting, replace the limiter pulley assembly. • Adjustment If the playback winding-up torque is not within the setting, replace the limiter pulley assembly. Note: When the torque cassette is set, put a weight (500g) to prevent rise. When the cassette torque meter is taken out. Turn off the power switch. • Problems caused by maladjustments 1. Much maladjusted : Tapes may get scratched. 2. Slightly maladjusted : Tapes may get slack halfway, resulting in the STOP mode. : Tapes may get entangled. Note: The winding-up torque fluctuates due to variation of rotation torque of supply reel disk. Read the center value of fluctuation as setting. • Problems caused by maladjustments 1. Much maladjusted : Tapes may get scratched. 2. Slightly maladjusted : Tapes may get slack halfway, resulting in the STOP mode. : Images onscreen may get distorted. : Tapes may get entangled. : Tapes may became out from cassette. 31 27DV-S100 27DV-CS10 CHECKING THE VIDEO SEARCH REWIND BACK TENSION • Remove the cassette housing control assembly. • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn on the power. Tension gauge 900 - 1,200gf Pinch roller • Checking 1. After pressing the play button, press the rewind button, and set the video search rewind mode. 2. Place the torque gauge on the take-up reel disk, and turn it counterclockwise very slowly (one rotation every 2 to 3 seconds) and check that the torque is within the set value 3.4 ± 1.5mN⋅m (35 ± 15gf⋅cm). • Problems caused by maladjustments 1. Tapes may get scratched whether much or slightly maladjusted Capstan shaft Tension gauge adapter Figure 1-13. 1. Detach the pinch roller from the capstan shaft. Do not separate excessively. Or the pinch lever and pinch double action lever may disengage. 2. Engage the tension gauge adapter with the pinch roller shaft, and pull in the arrow direction. 3. Gradually return the pinch roller, and measure the pulling force when the pinch roller contacts the capstan shaft. 4. Make sure that the measured value is within setting 9.0 N to 11.8 N (900 to 1,200gf). Torque gauge CCW CHECKING AND ADJUSTMENT OF TENSION POLE POSITION Take-up reel disk • Remove the cassette housing control assembly. • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn off the power. Figure 1-12. • 1. 2. 3. 4. 5. 6. Note: Set the torque gauge securely on the take-up reel disk. If it is not secure, the measurement will be incorrect. CHECKING THE PINCH ROLLER PRESSURE • Remove the cassette housing control assembly. Setting Turn off the power switch. Open the cassette tape (T-120), and fix with tape. Set the cassette tape into the unit. Put the weight (500g) on the cassette tape. Turn on the power switch. Make the adjustment with the beginning of a T-120 tape. (T-120) • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn on the power. • Checking Press the play button to set the playback mode. • Problems caused by maladjustments 1. Much maladjusted : The service life of the capstan and pinch roller may be shorter. 2. Slightly maladjusted : Images onscreen may get distorted. 500g Weight to prevent float (500g) Figure 1-14. • Checking 1. Set a cassette tape, push the REC button to place the unit in the SP record mode. Now check the tension pole position. 32 27DV-S100 27DV-CS10 2. Visually check to see if the right edge of the tension pole is within the 2.3 ± 0.25 from the right edge of the Sup guide shaft. Tension pole adjuster adjusting range Tension pole adjuster Sup guide shaft 90° Tension pole 2.3 ± 0.25 90° Make the adjustment with the beginning of a T-120 tape. Figure 1-15. Figure 1-18. At left side from the center line Adjust so that the delta mark of tension pole adjuster is within 90° range (left, right). CHECKING AND ADJUSTMENT OF RECORD/PLAYBACK BACK TENSION • Remove the cassette housing control assembly. • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn off the power. 2.3 ± 0.25 Figure 1-16. • 1. 2. 3. 4. 5. Insert the slotted screwdriver in the tension pole adjuster, and rotate counterclockwise. At right side from the center line Setting Turn off the power switch. Open the torque cassette meter and fix with tape. Set the cassette tape into the unit. Put the weight (500g) on the cassette torque meter. Turn on the power switch. 500g 2.3 ± 0.25 Weight to prevent float (500g) Figure 1-17. Cassette torque meter Insert the slotted screwdriver in the tension pole adjuster, and rotate clockwise. • Problems caused by maladjustments 1. Images onscreen may get distorted. Figure 1-19. • Checking 1. Push the REC button to place the unit in the SP record mode. 2. At this time ascertain that the back tension is within the setting (36.5 to 52g·cm) by seeing the indication of torque cassette meter. 33 27DV-S100 27DV-CS10 • Adjustment 1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A. 2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B. • Problems caused by maladjustments 1. Much maladjusted : Tapes may get scratched. 2. Slightly maladjusted : Images onscreen may get distorted. A B in the CW direction/CCW direction with respect to the supply reel disk so that the reel disk and torque gauge pointer rotate at equal speed, and make sure that the value is within the setting (CW direction: 4.9 to 13.7mN·m (50 to 140gf·cm); CCW direction: 2.9 to 9.8mN·m (30 to 100gf·cm). • Checking the brake torque at the take-up side Torque gauge Tension arm CW CCW Take-up reel disk Tension spring Figure 1-20. CCW: 4.9~13.7mN⋅m (50~140gf⋅cm) CW: 3.9~10.8mN⋅m (40~110gf⋅cm) CHECKING THE BRAKE TORQUE • Checking the brake torque at the supply side Figure 1-22. • Remove the cassette housing control assembly. • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn on the power. Torque gauge CCW CW • 1. 2. 3. Supply reel disk Setting Switch from the FF mode to the STOP mode. Disconnect the power cord. Set a torque gauge to zero on the scale. Place it on the take-up reel disk. • Checking 1. Turn the torque gauge at a rate of about one turn/2 sec in the CCW direction/CW direction so that the reel disk and torque gauge pointer rotates at equal speed and make sure that the value is within the setting (CCW direction: 4.9 to 13.7mN·m (50 to 140gf·cm), CW direction: 3.9 to 10.8 mN·m (40 to 110gf·cm). CCW: 2.9~9.8mN⋅m (30~100gf⋅cm) CW: 4.9~13.7mN⋅m (50~140gf⋅cm) Figure 1-21. • Remove the cassette housing control assembly. 2. Adjustment of the brake torque at the supply side and the take-up side • Unless the supply side brake torque or take-up side brake torque is within the setting, clean the felt surface of reel disk (supply, take-up) brake lever, check again the brake torque. • If value cannot be set within the setting yet, replace the main brake ass'y or main brake spring. • Problems caused by maladjustments 1. From the FF or REW to the STOP mode • Much maladjusted : The brake noise may get louder. • Slightly maladjusted : Tapes may get slack and scratched. • After short-circuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord, then turn on the power. • Setting 1. Set a torque gauge to zero on the scale. Place it on the supply reel disk. 2. Switch from the FF mode to the STOP mode. 3. Disconnect the power cord. • Checking Turn the torque gauge at a rate of about one turn/2 sec 34 27DV-S100 27DV-CS10 section and A/C head front section) (See the figure below.) 3. Align the left end of gear of A/C head arm with the punched mark of chassis, tentatively tighten the screws 1 and 2 so as to ensure smooth motion of A/C head arm. Tentative tightening torque must be 0.15 to 0.20 N·m (1.5 to 2.0kgf·cm). REPLACEMENT OF A/C (Audio/Control) HEAD 1. Remove the cassette housing control assembly. 2. In unloading state unplug the power cord. • Removal 1. Remove the screws 123, Azimuth screw, Tilt screw. 2. Unsolder the PWB fitted to the A/C head. Notes: 1. When replacing, never touch the head. If you touched, clean with the cleaning liquid. 2. When removing the screw 3, take care so that the spring may out. 1 3 3 Tilt screw Azimuth screw Height screw 2 Height screw Left end of A/C head plate gear Punched line mark on chassis Figure 1-25. 1 Spring Notes: 1. If the screws 1 and 2 are tighten tentatively too loose, the azimuth and height of A/C head may change when they are finally tightened. Therefore care must be taken. 2. After completion of A/C head be sure to adjust tape running. (Execute the running adjustment by the method described in page 37.) 2 Figure 1-23. • Replacement 1. Solder the removed PWB to the new head assembly. 2. Adjust the height from the A/C head plate (lower surface) to the A/C head base to 10.8mm with slide calipers. (3 places of azimuth screw section, tilt screw Solder New A/C head ass'y A/C head PWB Never touch the head A/C head base 10.8mm 10.8mm Figure 1-24. 35 27DV-S100 27DV-CS10 A/C HEAD HEIGHT ROUGH ADJUSTMENT HEIGHT ADJUSTMENT OF REVERSE GUIDE • Setting Azimuth screw 1. Adjust the height from the mechanism chassis to the reverse guide lower flange to 13.38 mm, using the reverse guide height adjustment jig, in tape loading state. (Refer to Figure 1-28 (a) (b).) Reverse guide height adjusting jig Reverse guide Reverse guide height adjusting jig Height screw Tilt screw Mechanism chassis Cassette tape (a) 13.38mm (b) Figure 1-28. 500g Weight to prevent float (500g) 2. Rotate counterclockwise the reverse guide height adjustment nut 1/10 turn. (For height adjustment use the reverse guide height adjustment box driver (JiGDRiVER 11055)). Mechanism chassis Box driver Figure 1-26. CCW 1. Set the cassette tape in the unit. 2. Press the PLAY button to put the unit in the playback mode. 3. Roughly adjust the height of the A/C head by turning the height screw until the tape is in the position shown below. Height adjusting nut A/C head Tape Figure 1-29. 0.3mm 3. Set the tape, and check for tape crease near the reverse guide in the playback mode. If crease is found, turn the reverse guide adjustment nut to remove crease. (As for crease check refer to Figure 1-30.) Figure 1-27. • Adjustment Adjust the height screw visually so that the control head is visible 0.3mm below the bottom of the tape. • Problems caused by maladjustments 1. Tapes may get scratched 2. Images onscreen distorted. A Capstan motor shaft Fixing guide 500g Weight to prevent float (500g) Mechanism chassis Reverse guide An example of crease near the reverse guide * Check for crease from the A direction. Figure 1-30. • Problems caused by maladjustments 1. Tapes may get scratched. 36 27DV-S100 27DV-CS10 tion, and adjust the envelop waveform to maximum with X value adjustment nut. Thereby the tape run rough adjustment is facilitated. 2. Especially the outlet side envelope waveform must have higher flatness. ADJUSTMENT OF TAPE DRIVE TRAIN 1. Tape run rough adjustment 1 Remove the cassette housing control assembly. 2 After shortcircuiting R7057 and JUMPER:420 provided on the main PWB, plug in the power cord. , then turn off the power. Set the tape for each check and / or adjustment shown below and turn on the power. 3 Check and adjust the position of the tension pole. (See page 33.) 4 Check and adjust the video search rewind back tension. (See page 32.) 5 Connect the oscilloscope to the test point for PB CHROMA envelope output (TP3301). Set the synchronism of the oscilloscope to EXT. The PB CHROMA signal is to be triggered by the head switching pulse (TP3302). 6 Set the alignment tape (VROATSV) to play. (Put a 500g weight on the cassette tape to prevent lift of cassette tape.) Figure 1-32. 2. Adjustment of A/C head height and azimuth 1 Perform the initial setting of A/C head position by the method stated in "page 35 Replacement 3". 2 Connect the oscilloscope to the audio output termina0l (TP6601). 3 Using the alignment tape in which 1 kHz linear audio signal has been recorded, adjust the height screw so as to get max audio output. 4 Using the alignment tape in which 7 kHz linear audio signal has been recorded, adjust the azimuth screw so as to get max audio output. 5 The adjustment of 3 and 4 twice or three times repeat, and finally adjust 4. Guide roller Cassette Tape 500g Weight of 500g Figure 1-31. 7 Press the tracking button (+), (–) and change the envelope waveform from max to min and from min to max. At this time make sure that the envelope waveform changes nearly parallel. 8 Unless the envelope waveform changes nearly parallel, adjust the height of supply side and takeup side guide roller so that the envelope waveform changes nearly parallel. (For envelop adjustment procedure refer to Figure 1-35.) 9 Turn the tilt screw to remove the tape crease at the fixing guide flange. Playback the tape and check for tape crease at the fixing guide flange. (1) If there is no tape crease Turn the tilt screw clockwise so that tape crease appears once at the flange, and then return the tilt screw so that the crease disappears. (2) If there is tape crease Turn counterclockwise the tilt screw so that the tape crease disappears. (Reference) If the tilt screw is turned clockwise crease appears at the lower flange. • Problems caused by maladjustments 1. Totally maladjusted • Images onscreen may get distorted or affected by noises, or may fail to appear. Notes: 1. Previously set the tracking control in the center posi- For X value adjustment Adjust the X value, turning the gear-type screwdriver. Figure 1-33. 3. Tape run adjustment 1 Connect the oscilloscope to PB CHROMA envelope output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switching pulse). 2 Rough adjustment of X value Tentatively fix A/C head arm screws 1 and 2 by the method described in page 35 "Replacement 3". After shortcircuiting R7057 and JUMPER:420, plug in the powercord, then turn off the power. And set the alignment tape (VROATSV) into the unit, turn on the power, then playback it. As a result the autotracking is automatically cancelled, so that the X value adjustment mode is set. Move the A/C head with the X value adjustment gear driver (JiGDRiVER-6) by the method shown in Figure 1-33, and adjust the A/C head so as to get the maximum envelope waveform. (Note: When the A/C head is adjusted, adjust so that the maximum envelop waveform is obtained nearest the position of initial setting made in page 35.) 37 27DV-S100 27DV-CS10 3 Next, change the alignment top to VROEFZCS to play back. Press the tracking button (+), (–) and change the envelope waveform from max to min and from min to max. At this time adjust the height of supply and take-up side guide roller with the adjustment driver (JiGDRiVERH-4) so that the envelope waveform changes nearly parallel. 4 If the tape is lifted or sunk from the helical lead surface, the PB CHROMA envelope waveform appears as shown in Figure 1-35. 5 Press the tracking button (+), (–) and make sure that the envelope waveform changes nearly parallel. 6 Finally check tape crease near the reverse guide. If tape crease is found, remove it as stated in page 36 "HEIGHT ADJUSTMENT OF REVERSE GUIDE" item 3. PB CHROMA Envelope CH-1 CH-2 Head switching pulse Figure 1-34. 4. A/C head X value adjustment 1 Tentatively fix A/C head arm screws 1 and 2 by the method described in page 35 "Replacement 3". 2 After shortcircuiting R7057 and JUMPER:420, plug in the powercord, then turn off the power. And set the alignment tape (VROEFZCS) into the unit, turn on the power, then playback it. As a result the autotracking is automatically cancelled, so that the X value adjustment mode is set. When the tape is above the helical lead. Supply side Adjustment Supply side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope. Take-up side Take-up side guide roller rotated in clockwise direction (lowers guide roller) to flatten envelope. When the tape is below the helical lead. Supply side Take-up side Supply side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The supply side guide roller is then rotated in the clockwise direction to flatten the envelope. Take-up side guide roller rotated in counterclockwise direction (raises guide roller) to make the tape float above the helical lead. The take-up side guide roller is then rotated in the clockwise direction to flatten the envelope. Figure 1-35. 3 Move the A/C head with the X value adjustment • Problems caused by maladjustments gear driver by the method shown in Figure 1-33, 1. Totally maladjusted • Tapes may get scratched. and adjust the A/C head so as to get the maximum • Images onscreen may get distorted or affected by envelope waveform. (Note: At this time adjust so as noises, or may fail to appear. to get the maximum envelope waveform nearest • The linear audio level may get degraded. the A/C head position which has been set in case of X value rough adjustment as stated in page 37, 3- Note: When the A/C head X value adjustment is performed, be 2.) 4 Tighten finally the screws 1 and 2. Be sure to sure to perform at first X value rough adjustment (refer to tighten at first the screw 1 and then the screw 2. page 37, 3-2). 1 Final tightening torque is 0.6N·m (If the screw 2 is 2 tightened first, the X value may deviate.) 5 Adjust the playback switching point (Refer to the electric adjustment method.) 6 Playback the self-picture-recorded tape, and check the flatness of envelope waveform and sound. Figure 1-36. 38 27DV-S100 27DV-CS10 REPLACEMENT OF THE CAPSTAN D.D. (DIRECT DRIVE) MOTOR • 1. 2. 3. REPLACEMENT OF DRUM D.D. MOTOR 1. Set the ejection mode. 2. Withdraw the main power plug from the socket. Removal (Follow the order of indicated numbers.) Remove the reel belt 1. Remove the slow brake lever 2. Remove the three screws 3. • 1. 2. 3. 4. 5. 3 Notes: 1. In removing the D.D. stator assembly, part of the drum earth spring pops out of the pre-load collar. Be careful not to lose it. 2. Install, so that the D.D. rotor ass'y and upper drum ass'y mounting direction check holes align. (Align the upper drum dent with the rotor hole.) 3. Be careful not to damage the upper drum or the video head. 4. Protect the hole elements from shock due to contact with D.D. stator or D.D. rotor ass'y. 5. After installation adjust the playback switching point for adjustment of servo circuit. Capstan D.D. motor control PWB Capstan D.D. motor 1 Removal (Perform in numerical order.) Disconnect the FFC cable 1. Unscrew the D.D. stator assembly fixing screws 2. Take out the D.D. stator assembly 3. Unscrew the D.D. rotor assembly fixing screws 4. Take out the D.D. rotor assembly 5. Reel belt 2 Slow Brake Lever 2 D.D. stator ass'y Figure 1-37-1. 3 • Reassembly 1. Taking care so that the capstan shaft does not contact the mechanism chassis, set its position on the mechanism chassis, and then install with the three screws. 2. Install the slow brake lever. 3. Install the reel belt. Notes: 1. Before installing the capstan D.D. motor, confirm whether an acetate tape (ZTAPEN120020E) is drawn on the back of mechanism chassis. 1 4 4 5 D.D. rotor ass'y Upper drum Stick on acetate tape on the projection part of the chassis. Capstan Motor Installation posltion. Figure 1-38. MechanismChassis from the back. Figure 1-37-2. 2. After installing the capstan D.D. motor, be sure to rotate the capstan D.D. motor and check the movement. 3. Set the tape, and check for the tape crease near the reverse guide in the playback mode. Adjust the A/C head and azimuth as stated in page 37 item 2. If crease is found, adjust as stated in page 36 "HEIGHT ADJUSTMENT OF REVERSE GUIDE". 39 27DV-S100 27DV-CS10 REPLACING THE UPPER AND LOWER DRUM ASSEMBLY ASSEMBLING OF PHASE MATCHING MECHANISM COMPONENTS • Assemble the phase matching mechanism components in the following order. 1. Assemble the pinch roller assembly and pinch drive cam. 2. Mounting the shifter (on the back of the mechanism chassis). 3. Mounting the master cam (on the back of the mechanism chassis). 4. Assemble the connection gear, slow brake and loading motor parts. • Replacement (Perform in the numerical order) 1 Remove the motor as stated in page 39 D.D. motor replacement. 2 Remove the drum earth brush ass’y 2. 3 Remove the drum base 3 from the upper and lower drum assembly 1. [Cares when replacing the drum] 1. Be careful so that the drum earth brush is not lost. 2. Do not touch directly the drum surface. 3. Fit gently the screwdriver to the screws. 4. Since the drum assembly is an extremely precise assembly, it must be handled with utmost care. 5. Make sure that the drum surface is free from dust, dirt and foreign substances. 6. After replacing the drum be sure to perform the tape running adjustment. After that, perform also the electrical adjustment. • Playback switching point adjustment • X-position adjustment and check • Standard and x-3 slow tracking adjustment 7. After replacing the drum clean the drum. • Pinch drive cam and pinch roller assembling method. (Place the following parts in position in numerical order.) (1)Reverse drive lever 1 (2)Reverse guide spring 2 (3)Reverse guide lever ass’y 3 (4)Reverse guide height adjusting nut 4 7 (5)Pinch drive cam 5 (6)Pinch roller ass’y 6 (7)Open lever 7 6 4 2 3 1 1 2 5 3 Figure 1-40. Figure 1-39. 40 27DV-S100 27DV-CS10 1Insert Reverse Guide Lever Ass’y Insert reverse guide lever ass'y 2 Insert pinch drive cam Turn the reverse guide lever assembly counterclockwise to the stopper. Align here. Fit the pinch drive cam so that the notch of pinch drive cam aligns with the dent of pinch drive lever assembly. Fit the pinch drive cam so that the notch of pinch drive lever assembly aligns with the half-round notch of chassis. Pinch drive lever ass'y Figure 1-41-1. 2Insert Pinch Roller/Pinch Double Action Lever Ass’y. 3Insert Open Lever. Pinch Roller Double Action Lever Ass'y Open lever Phase Matching Point 2 Figure 1-41-2. Figure 1-41-3. 41 27DV-S100 27DV-CS10 1. Make sure that the loading gear is at the PhaseMatching point 1 as shown below. 2. Install, paying attention to insert point 5 and release point 3. 3. For the phase matching at the insert point 1, see the Phase-Matching point 2 as shown below. 4. Finally fix the inserts 1 and 4. INSTALLING THE SHIFTER Drum Capstan D.D. motor Reel pulley (Bottom side of mechanism chassis) Phase-Matching point 2 Figure 1-42. Loading gear (T) Round mark Insert point 1 Sifter Shaft 1 Half round notch Insert point 3 Insert point 2 Insert point 4 Shaft 1 Rotation point 2 Shaft 2 Phase-matching point 1 Shaft 1 Figure 1-43. 42 Release point 3 Insert point 5 27DV-S100 27DV-CS10 INSTALLING THE MASTER CAM (AT REAR SIDE OF MECHANISM CHASSIS) REPLACEMENT OF LOADING MOTOR • Removal 1. Make sure beforehand that the shifter is at the point as shown below. 2. Place the master cam in the position as shown below. Apply grease E ring (XRESJ30-06000) Apply grease Master cam Fully turn clockwise No grease Fully turn counterclockwise Face the wide tooth side ward Figure 1-44-1. Note: See the figure below for the phase matching between the master cam and the casecon drive gear. 3. Finally fix with the E ring. Figure 1-45. Master cam Casecon drive gear • Replacement Remove the loading motor, and install the replacement loading motor as shown below. Half-round notch +0 10.2 –0.2 mm Round mark When installing the master cam, align the casecon drive gear round mark with the half-round notch of master cam. Figure 1-44-2. Figure 1-46. The loading motor pressing-in must be less than 147 N (15kgf). Adjust the distance between motor and pulley to 10.2 +0.2 –0.2 mm). 43 27DV-S100 27DV-CS10 ASSEMBLY OF CASSETTE HOUSING 1. Drive Gear and R Drive angle ass’y MSPRT0381AJFJ Apply grease Apply grease Apply grease Figure 1-47. 2. Synchro Gear, Drive Gear L and Drive Gear R LANGF9592AJFW Top surface should be free from scratches or soil. Drive angle Drive gear R Frame Figure 1-48. 44 27DV-S100 27DV-CS10 ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY Notes: • Before the adjustment: Electrical adjustments discussed here are often required after replacement of electronic components and mechanical parts such as video heads. Check that the mechanism and all electric components are in good working condition prior to the adjustments,otherwise adjustments cannot be completed. • Instruments required: • Blank video cassette tape • Alignment tape (VROATSV) Figure 2-1. 45 27DV-S100 27DV-CS10 VCR SERVO CIRCUIT ADJUSTMENT Note: The procedure of the adjustments is HEAD SWITCHING POINT → SLOW TRACKING PRESET → FV of STILL PICTURE ADJUSTMENT OF HEAD SWITCHING POINT 1. Playback the alignment tape. (VROATSV) 2. Press both REC key and VOL-DOWN key on the front panel more than 2 seconds to turn the unit into the adjustment mode. (PROGRAM TIMER LED is lighting and “T” is displayed on the monitor screen.) 3. Press PLAY key. 4. Automatically head switching point adjustment is started, and the unit will be back to PB mode after the adjustment is finished.(PROGRAM TIMER LED is putting out) 5. Press STOP key. ADJUSTMENT OF SLOW TRACKING PRESET 1. Playback SP and EP mode self recorded tape. 2. Playback SP mode recorded portion at slow mode. 3. Press both REC key and VOL-DOWN key on the front panel more than 2 seconds to turn the unit into the adjustment mode. (PROGRAM TIMER LED is lighting and “T” is displayed on the monitor screen.) 4. Press SLOW key. 5. Automatically adjustment start, and the unit will be back to slow mode after the adjustment is finished. (PROGRAM TIMER LED is putting out). 6. To check the still noise, push PLAY key and then STILL key. 7. Next playback EP mode recorded portion at slow mode. 8. As same as 2-6 items, adjust EP mode slow tracking preset and EP mode noise. ADJUSTMENT OF FV (False Vertical Sync) OF STILL PICTURE 1. Play a cassette which was self-recorded by the unit in SP mode. 2. Press the PAUSE/STILL button to freeze the picture. 3. Look at the monitor screen and adjust the TRACKING (+) and / or (–) buttons so that the vertical jitter of the picture is minimized. 4. Play and freeze the self-recorded tape in EP mode and make sure the vertical jitter of the picture is not noticeable. 46 27DV-S100 27DV-CS10 TEST MODE OF DVD SECTION "NO DISC" state Press both of the "PLAY" key and the "STOP" key on the DVD front panel of the main unit for 5 seconds during the DVD mode to turn the unit into the DVD test mode. (Turn the power off to cancel the test mode.) F0000000 00000000 (DVD test mode) Check mode of the DVD program contents Press the "1" key on the remote control or the "STOP" key on the main unit. The preparation date display of the program 10000000 ~~~~~~~~ (Last update) Press the "PLAY" key. Model number display 10000001 0000D031 (Model number) Press the "PLAY" key. The version display of the program 10000002 ~~~~~~~~ (Program version) Press the "PLAY" key. Region number display 10000003 00000001 (Region code: binary display) Press the "PLAY" key. Micro-code number display 10000004 ~~~~~~~~ Micro-code means the process (Micro-code version) program of the system IC. Press the"PLAY" key. The preparation date display of the servo program 10000005 ~~~~~~~~ (Servo version) Press the"PLAY" key. The display is returned to the initial screen of the test mde. Press the "3" key. (to turn the unit into the dynamic test mode.) DYNAMIC TEST 30000000 00000000 (Turn the power off to cancel the dynamic test mode.) Laser test mode Press the "1" key. LASER TEST 30000001 000000DD The tray opens, the DVD laser is lit, the spindle turns momentary and the sled moves to the outer side. Press the "1" key. LASER TEST 30000001 000000CD The DVD laser goes out, the CD laser is lit, the spindle turns momentary and the sled moves to the outer side. Press the "1" key. LASER TEST 30000001 00000000 The DVD and CD lasers go out, the spindle turns momentary and the sled moves to the outer side. Press the "1" key. (Unplug the AC cord to cancel the laser test mode.) To (1) 47 27DV-S100 27DV-CS10 From (1) (dynamic test mode) Step test mode Press the "2" key. STEP TEST 30000001 00000000 Put a disc on the tray after the tray is opened. Press the "OPEN/CLOSE" key. (to close the tray.) STEP TEST 30000200 00000000 (loading the disc) STEP TEST 30000201 00000000 Focus on Press the "PLAY" key. STEP TEST 30000202 00000000 RF gain adjustment, Tracking on Press the "PLAY" key. STEP TEST 30000203 00000000 Focus gain adjustment Press the "PLAY" key. STEP TEST 30000204 00000000 Tracking gain adjustment Press the "PLAY" key. STEP TEST 30000205 00000000 Focus balance adjustment Press the "PLAY" key. (DVD operation) In case of 2–layer DVD, STEP TEST RF gain, focus gain and DD000210 00000000 focus balance adjustments of layer 0. STEP TEST Reading control data DD000211 00000000 (CD operation) Tracing playback mode after reading TOC. (TOC: Table of Contents) (~~~~~~~~ is SUB-Q (address)) STEP TEST END CD000210 ~~~~~~~~ Press the "PLAY" key. STEP TEST END Tracing playback mode DD000212 ~~~~~~~~ (~~~~~~~~ is sector ID (address)) (Unplug the AC cord to cancel the step test mode.) Tracing playback, jump test mode Press the "3" key. PLAY TEST 30000001 00000000 Put a disc on the tray after the tray is opened. Press the "OPEN/CLOSE" key. (to close the tray.) PLAY TEST DD000302 ~~~~~~~~ Tracing playback mode (~~~~~~~~ is sector ID (address)) Pressing the keys on the remote control mentioned in the table below enables the jump test. Jump Key Jump Key 1 3 –1 1 102 6 –102 4 510 9 –510 7 511 MEMORY –511 CLEAR 765 REPEAT –765 2 –766 5 7000 PROGRAM –7000 8 15000 SKIP/FWD –15000 SKIP/REV To (2) (Unplug the AC cord to cancel the tracing playback, jump test mode.) 48 27DV-S100 27DV-CS10 From (2) (dynamic test mode) Spindle offset adjustment mode Press the "DISC MENU" key. SPIN OFFSET Tray is opened. ADJUST COMPLETE 00000000 00000~~~~ (The spindle offset is adjusted automatically.) The adjustment result is indicated in the ~~~~ portion. (When the adjustment is complete, the unit turns back to the dynamic test mode, and "3000000 00000000" is displayed on the screen.) [ROM REWRITING MODE] This mode is able to update the version of the DVD program. Please confirm the program version according to the procedure for the DVD test mode before you start the rewriting. 1. Connect a computer to the unit as shown below. Start the rewriting software of the computer. 2. Pressing both of the "PLAY" key and the "SKIP/FWD" key on the DVD front panel of the unit, turn the power on. (Keep on pressing both keys for 3 seconds or so.) The unit turns into the ROM rewriting mode, and the VCR indicator starts flashing at 1Hz. 3. Following the computer’s onscreen message, type in "Y" and press "ENTER" key. When the command for the data transfer starts the rewriting job, the VCR indicator and the DVD indicator are alternately flashing at 1Hz. 4. When the rewriting is complete, only the DVD indicator keeps on flashing at 1Hz. 5. Finally press the "STOP" key of the DVD and turn the power off. TV/VCR/DVD 27DV-S100 27DV-CS10 Computer (DOS) Connect to the DIGITAL OUT terminal. ROM writing tool 49 STOP End G mechanical timing Insert cassette. Cassette is ejected and loading motor stops. Cam graph E Mode check Cam mark 25 Mode detection outside (D709 SW B) Mode detection inside (D708 SW A) Double action rack slides. 20 Start sensor close. 15 10 Cassette inserting 5 0 60 CA/END CS/EJ 0 120 180 19.812 240 PU1 179 UL 81 PU2 200 300 PB 265 VSR 233 SLOW 282 Does mechanism position sw. come off within 2.5 sec.? 380 STOP 334 FF 316 Loading motor starts in normal direction and master cam counter clockwise. YES 50 EJ UL PU 0 0 0 0 0 1 1 1 Mode detection inside 1 1 0 0 0 0 1 1 S sensor 1 1 0 1 1 or 0 0 PU2 VSR PB SLW FF STP 1 1 1 1 0 1 1 0 1 0 0 1 1 0 1 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 NO (Cassette is judged caught halfway.) Are start/end sensors at low level NO before cassette insertion ? (Cassette LED or some other part is judged defective.) 10.354 12.812 Mode detection outside Loading motor turns in reverse direction and master cam counterclockwise. YES Drum motor starts. Open S sensor Close Mode detection inside Mode detection outside sensor A sensor B CS/EJ 1 0 ULD 1 1 PU1 1 1 PU2 0 1 VSR 0 1 PB 0 0 SLOW 0 1 FF 0 1 STOP 0 0 Tape loading. Pinch roller comes into contact. Fullloading Cam switch is at PB position. Loading motor stop. Is drum FG pulse outputted ? YES End NO Unloading 27DV-S100 27DV-CS10 CASSETTE INSERTION * This flowchart describes the outline of the mechanism’s operation, but does not give its details. MECHANISM OPERATION FLOWCHART AND TROUBLESHOOTING GUIDE MECHANISM OPERATION FLOWCHART STOP REC/PLAY PLAY Loading motor turns in counterclockwise direction and master cam clockwise. Capstan motor turns counterclockwise. Picture appears. YES Slow brake pressing Slow brake comes into contact with capstan motor. VSR VSR Press REW key. Pinch roller releasing PLAY Press PLAY Key. Loading motor turns clockwise and master cam counterclockwise. Loading motor turns counterclockwise and master cam clockwise. Release pinch roller. Capstan motor turns counterclockwise. PB speed. Cam switch is at PU2 position. NO Cam switch is at STILL position. End Loading motor stops. Unloading PLAY Press STILL key. Press REC/PLAY key. Is take-up reel sensor signal outputted ? STILL Stop loading motor. Idler swinging Cam switch is at PB position. Turn capstan motor in reverse direction. End Loading motor turns clockwise. Capstan motor stops. Release the supply auxiliary brake. End 51 Cam switch is at PU1 position. PLAY VSF REC/PLAY STOP Pinch roller pressing Turn loading motor counterclockwise. Press pinch roller. Press FF key. Press STOP key. Cam switch is at VSR position. Set capstan motor to search speed. End Capstan motor turns in reverse direction. Stop loading motor. Stop capstan motor. Set capstan motor to search speed. End Is take-up reel sensor signal outputted ? NO YES Unloading 27DV-S100 27DV-CS10 End FF/REW STOP Press FF/REW key. FF/REW operation CASSETTE EJECT Press EJECT key. Turn capstan motor in normal or reverse direction, after the remaining tape has been detected. Loading motor turns in clockwise and master cam counterclockwise. Tape unloading Capstan motor turns in reverse direction. End Cam switch is at UL position. Stop loading motor. FF/REW STOP 4 supply reel pulses outputted ? Press STOP key. 52 YES Stop capstan motor. Capstan motor turns clockwise. Cam switch is at Stop position. Loading motor turns clockwise. Loading motor stops. End Capstan motor turns clockwise. YES Does the take-up reel pulse output two edges ? Loading motor turns counterclockwise. Brake function NO Cam switch is at Eject position. Cassette eject Loading motor stops. Capstan motor stops. End NO Capstan motor turns counterclockwise in about 2 seconds. 27DV-S100 27DV-CS10 STOP MECHANISM TROUBLESHOOTING 1. FF/REW FAILURE (NO TAPE WINDING) 2. REC/PLAY FAILURE (MODE RELEASE) Press FF key. Is master cam at FF position ? NO YES Does loading motor operate ? NO YES Modes changing smoothly through cam switch ? Is voltage applied NO to loading motor ? YES NO Voltage supply system in trouble. Is the master cam NO at PB position ? 53 YES YES Replace the idler ass’y. YES Is the pulse NO outputted from reel sensor ? YES The cassette tape is presumably damaged. Voltage supply system in trouble. Loading motor is damaged. Replace it. YES NO Voltage supply system in trouble. Loading motor control system in trouble. Does capstan motor turn ? NO YES Replace the capstan motor. Are idler wheel NO ass’y and reel disk in mesh ? Is voltage applied NO to loading motor ? YES Modes changing smoothly through cam switch ? Loading motor is damaged. Replace it. Mode sensor system in trouble or master cam malpositioned. Loading motor control system in trouble. Are Vco 12V and Vcc 5V applied ? NO YES YES YES Does capstan NO motor turn in FF (or REW) direction ? Does loading motor operate ? Are Vco 12V and Vcc 5V applied ? NO Voltage supply system in trouble. YES Replace the capstan motor. Are idler wheel NO ass'y and reel disk in mesh ? Replace the idler ass’y. YES Replace the reel sensor. Is the pulse NO outputted from reel sensor ? Replace the reel sensor. YES Check main PWB. 27DV-S100 27DV-CS10 27DV-S100 27DV-CS10 3. WINDING FAILURE AT VSR 4. UNUSUAL SOUND IN EACH MODE 4-i) Unusual sound in cassette insertion and ejection mode Is Playback function normal ? NO Go to 2. REC/ PLAY FAILURE routine. YES Is unusal sound heard during cassette control running ? Press REW key. Master cam shifting to VSR position ? NO Go to 2. REC/ PLAY FAILURE routine. YES Are idler wheel NO ass’y and supply reel disk in mesh ? 54 Is supply reel disk NO winding torque normal ? YES Replace limiter pulley ass’y. YES Is pulse outputted NO from reel sensor ? YES Check main PWB. NO Is unusual sound heard during loading/unloading ? YES Replace loading motor block. Replace reel sensor. Replace cassette control ass’y. NO Unusual sound heard with pinch roller lever going up or down ? Replace idler gear ass’y. YES YES Check pinch roller drive cam, pinch roller drive lever and reverse guide for their actions. Replace damaged one with new one. 4-ii) Unusual sound in FF/REW mode Is reel disk height as specified ? NO Adjust reel disk height. YES Thrust gap found at reel disk ? NO Check reel disk and main chassis. And replace defective parts. YES Drive system out of contact with any part on main PWB ? YES Rearrange the parts on main PWB. NO 55 Turn capstan motor by hand. Unusual sound heard ? YES Replace capstan motor. NO Check drive system’s gears for damage. Replace damaged gear with new one. • Reel disk • Limiter pulley ass’y • Idler wheel ass’y 27DV-S100 27DV-CS10 NO +B voltage = 130V ? (L9720) Check 5V regulator (IC9021) NO NO RGB AMP (IC8850) bias output from pin (9),(8),(7)? Check X7001 YES YES System control (IC2001) pin(25)= 5V ? NO Check CRT screen control and FBT (T5603) Check reset circuit (IC2002) YES System control (IC2001) pin(1)= 60Hz signal ? NO Check TC detector (IC901) 56 YES YES System control (IC2001) pin(4)(power control)=5V ? pin(13)(TV power)=5V ? (when turn on) NO Replace IC2001 Check TV power circuit YES YES System control(IC2001) pin(37),(38)= 14.32MHz ? NO Power control SW(Q9101) and relay (RY9701) are normal ? NO Check power control circuit and relay drive circuit YES 12V REG (IC9740) pin(3)=12V? NO Check IC9740 and 12V line of TV power circuit YES Error amp (IC9741) pin(1)=130V ? YES Check deflection circuit and FBT NO Check 130V line and other TV power circuit RGB AMP (IC8850) pin(6)=210V? YES Replace IC8850 NO Check HEATER line 27DV-S100 27DV-CS10 System control(IC2001) pin(36),(51),(73)= 5V ? FLOW CHART No. 1-2 No raster TROUBLESHOOTING FLOWCHARTS OF TV SECTION FLOW CHART No. 1-1 No turn on FLOW CHART No.1-3 No video AV SW (IC1301), video signal (1Vp-p) NO input to pin(63) (Tuner), pin(8) (LINE1), pin(15) (LINE2) ? Check each line Tuner TU1951 pin(19) output LINE1 J1301 LINE2 J3801 Y/C separation (IC1401), chroma signal output from pin(13) ? YES FLOW CHART No.1-4 No color NO Y/C separation (IC1401), 3.58MHz signal input to pin(10)? Video chroma (IC4401), chroma signal input to pin(13)? Check IIC-Bus and +9V line pin(33), (34) (IIC-Bus), pin(42) (+9V) YES Replace IC1401 NO YES AV SW (IC1301), video signal (2Vp-p) NO output from pin(53) ? YES NO Check between IC1401 and IC4401 YES Y/C separation (IC1401), video signal (0.75Vp-p) input to pin(4) ? NO Check video signal line between IC1301 and IC1401 NO Y/C separation (IC1401), fsc (3.58MHz) input to pin(10) ? NO Video chroma (IC4401) 3.58MHz signal output to pin(1)? YES Y/C separation (IC1401), Y-Signal (1.30Vp-p) output from pin(15) ? YES YES NO Check between IC1401 and IC4401 YES Replace IC1401 57 Video chroma (IC4401), Y-signal input to pin(15) ? NO Check between IC1301 and IC4401 NO Check Video chroma circuit YES Video chroma (IC4401), R,G,B-signal output from pin(43), (42), (41) ? NO Check X-tal (X4801) Video chroma (IC4401), pin(5), (6) output from B-Y, R-Y signal and pin(52), (51) input to B-Y, R-Y signal? NO Check color control of picture adjustment YES Replace IC4401 YES RGB amp (IC8850), RGB-signal input to pin(1), (2), (3) ? NO YES YES Video chroma (IC4401), Y-signal output from pin(4) and input to pin(53)? Video chroma (IC4401), pin(10)=3.58MHz signal? NO Check between Terminal PWB and CRT PWB YES RGB amp (IC8850), RGB-signal output from pin(9), (8), (7) ? Check the CRT screen control Replace IC8850 27DV-S100 27DV-CS10 YES NO IC3001(MTS) Audio signal output from pin(3),(2)? When a unit changes into a dangerous state, it turns off automatically and makes Power LED flash on and off continually to indicate the Protect Mode. Flashing 1 time X-Ray (/Def. Over Current/Dynamic Focus Over Voltage) protect Flashing 2 times Vetical-Out Protect Flashing 3 times TV Power Short Protect NO YES Speaker amp (IC6351) pin(10) = 27V ? NO X-Ray Protect Speaker amp (IC6351) Audio signal input to pin(2), (5) ? System control (IC2001) pin(83) = 5.0V("H")? Check between IC3001 and IC6351 YES NO Check speaker mute line between IC2001 (µ-com) and IC6351 Check between Q2808 and IC2001 NO X-Ray protector D5623 anode = over 4V? YES Check or replace IC2001 NO YES X-Ray protector Q2808 collector = 5.0V("H")? YES Speaker amp (IC6351) pin(8) = 0V ? (Check when power On) Check TV power circuit YES NO FLOW CHART No.1-6 Protect Mode NO Check between D5623 and Q2808 base YES Check between TV Power PWB and speaker. 58 YES X-Ray protector D5623 cathode = over 13.5V? Check between IC3001 and IC3201 (EQ Sound) YES Replace IC3001 NO Check between TU1951 (tuner) to IC3001 Check TV power circuit Check Hi-Voltage (33kV;CRT anode), FBT T5603 and peripheral circuit NO IC3001 (MTS) Audio signal input to pin(14)? NO YES NO YES IC3001 (MTS) Audio signal output from pin(40), (39)? +B voltage (L9720) = 130V? Def. over current protector Q5606 base = over 4V? NO Check Q5606 and D5608 YES Def. over current detector Q5610 collector = about 130V? YES Check FBT T5603, peripheral circuit and deflection circuit NO YES Dynamic focus over voltage detector D5627 anode = over 5V? NO Check R5646, R5648 and D5628 Check dynamic focus circuit (Q5604, T6601 and peripheral circuit) 27DV-S100 27DV-CS10 FLOW CHART No.1-5 No Sound FLOW CHART No.1-8 FLOW CHART No.1-7 Vertical Out Protect (Check when power on) YES System control (IC2001) V-pulse input to pin(45)? YES Replace IC2001 NO NO Vertical out (IC5601) V-pulse output from pin(3)? NO System control (IC2001) pin(97) = over 3.5V? TV Power Short Protecto D5625 cathode H-pulse output from FBT? YES Check between D5625 and IC2001 Short protector drive Q9752 collector = 0V? NO 59 Check Video-chroma circuit and replace IC4401 Check or Replace IC2001 YES Check between Q9752 and IC2001 NO YES Check FBT and C5633/C5639 27V Line D9751 cathode = normal (27V)? YES Check 27V line and IC6351 NO NO Video-chroma (IC4401) H-Pulse output from pin(23)? YES NO YES NO Q5612 base H-Pulse output from T5602 pin(4)? System control (IC2001) pin(86) = 0V("L")? (Check when power on) YES Check between IC4401, Q5608 and T5602 16V Line D9752 cathode = normal (16V)? YES Check 16V line and 12V regulator IC9740 NO 8V Line D9755 anode = normal (8V)? YES Check 8V line and 5V regulator IC1902 NO Check 130V line and peripheral circuit Check between IC5601 to IC2001 Def. processor (IC5602) V-Pulse output from pin(9)? YES Check between IC5602 to IC5601 NO Video-Chroma (IC4401) HPulse output from pin(23)? YES Check between IC4401 to IC5602 NO 27DV-S100 27DV-CS10 Mechanism malfunction. Turn off AC power and get the set restarted. Does the AT5V line function? NO Check IC9021 and its peripheral circuits. YES Is there 14MHz oscillation at pins NO (37) and (38) of IC2001? Check IC2001 and X7001. YES The REC key does not function. All the other keys function. No power is supplied (PC5V). The unit stops 3 seconds after loading. The pinch roller fails to contact the capstan during loading. The unit stops 5 seconds after loading. The FF or REW key does not function. The EJECT key alone functions. NO 60 Turn on power. Is the voltage at pin (4) of IC2001 at "H" level? NO YES YES Is PC5V available? YES Is there the H.SW.P. output signal at pin (23) of IC2001? Is the cassette NO tape without erase protection tag? NO Check Q9101. YES No recording can be made on cassette tape without the tag. NO Is there the reel pulse input signal at pins (2) and (3) of IC2001? YES Replace IC2001. Replace IC2001. See Flowchart No. 10. See Flowchart No. 11. NO Does the loading motor stop after loading? Replace IC2001. NO Replace the REC TIP switch. Is there the REC TIP SW signal at pin (64) of IC2001? YES Replace IC2001. NO Check the signal line. See Flowchart No. 3. A cassette tape is inserted but pops out itself. YES Check the pinch roller pressure. Check the PC12V line and PC23V line. Does the REC TIP YES switch function? NO Check the cam switches D7008 and D7009. See Flowchart No. 2. TROUBLESHOOTING FLOWCHARTS OF VCR SECTION TROUBLESHOOTING MECHANISM CONTROLLER (1) 27DV-S100 27DV-CS10 FLOW CHART No. 2-1 FLOW CHART No. 2-2 Cassette tape failure to come in or unexpected ejection. Push in the cassette tape. Does the start sensor (Q7001(C)) shift from "H" to "L" level? No tape travel in FF/REW mode. NO YES Push in the cassette tape. Does the loading motor start? Check the performance of the cassette controller's doubleacting rack. Check also the start sensor (Q7001) and cassette LED (D7001). Replace as required. 61 Check the setup of relay gear and master cam. Check the cassette controller for misalignment. Are both the start sensor and end sensor at "H" level? NO Check the start sensor (Q7001) and end sensor (Q7002). YES NO Go to Flowchart No. 5 "Loading motor failure to start". Push in the cassette tape and immediately press the FF key. Is the remaining tape fastforwarded at "PB" position? YES NO Check the start sensor (Q7001) and end sensor (Q7002). Replace as required. Press the FF/REW key after the above FF action. Does the loading motor start? YES Push in the cassette tape. Are both the start sensor and end sensor at "H" level? YES FLOW CHART No. 2-3 NO NO Go to Flowchart No. 5 "Loading motor failure to start". YES Does the master cam shift to NO "FF" position? (See Mechanism Operation Flowchart.) YES Are there the specified mechanism position input signals at pins (6) and (7) of IC2001? YES Check IC2001 and replace as required. Is the drum motor running? NO Go to Flowchart No. 6 "Drum motor failure to start". NO Go to Flowchart No. 10 "No H.SW.P. output signal". NO Go to Flowchart No. 8 "Capstan motor failure to start". NO Check the setup of master cam and relay gear. Check also the mechanism position sensors (D7008 and D7009). Replace as required. YES Is there the H.SW.P. output signal? YES Is the capstan motor running? YES Is the reel running with the idler NO in mesh with the reel stand? Replace the idler assembly. YES Are there the supply and take- NO up reel pulse input signals at pins (2) and (3) of IC2001? Cassette tape assumed to be defective. 27DV-S100 27DV-CS10 YES Go to Flowchart No. 11 "No supply and take-up reel pulse output". Unexpected clearing out of REC/PB mode. Are both the start sensor NO and end sensor at "H" level? YES Is the master cam at "PB" NO position? (See Mechanism Operation Flowchart.) YES Check the start sensor (Q7001) and end sensor (Q7002). Replace as required. Check also the cassette tape (for magnetic substance peel-off, for example). Is the loading motor running? YES Are there the specified mechanism position signals at pins (6) and (7) of IC2001? YES Check IC2001 and replace as required. Is the drum motor running? 62 NO Go to Flowchart No. 6 "Drum motor failure to start". NO Go to Flowchart No. 10 "No H.SW.P. output signal". NO Go to Flowchart No. 8 "Capstan motor failure to start". YES Is there the H.SW.P. output signal? YES Is the capstan motor running? YES Is the reel running with the NO idler in mesh with the reel stand? YES Go to Flowchart No. 11 "No supply and take-up reel pulse output". Replace the idler assembly. FLOW CHART No. 2-5 Loading motor failure to start. Are the control signals at NO pins (11) and (12) of IC7006 as specified? (See the table at right.) YES NO NO Go to Flowchart No. 5 "Loading motor failure to start". Check the setup of relay gear and master cam. Check also the mechanism position sensors (D7008 and D7009). Replace as required. Is PC12V applied at pins (9) and (10) of IC7006? NO YES Do the voltages (shown at NO right) appear at pins (13) and (15) of IC7006? YES Disconnect the loading motor connector "AL" and apply external DC voltage NO (about DC8V) to the motor terminal. Does the motor start? YES Check the loading motor connection with pins (13) and (15) of IC7006. Check pins (91) and (90) of IC2001. Check also the IC2001 performance. Replace as required. Check the PC12V line. Pin (11) Pin (12) Normal turn (loading direction) H L Reverse turn (unloading direction) L H:4.7V L:0V Stop H H H Replace IC7006. Pin (13) Pin (15) Check the mechanism for overload, and the setup of relay gear, master cam and shifter. Replace the loading motor. Normal turn Reverse turn About 11V About 1V About 1V About 11V FLOW CHART No. 2-6 Drum motor failure to start. Are 12V and 5V applied at pins (21) and (3) of IC7006 respectively? NO Check the PC12V and PC5V lines. YES Does the voltage at pin (2) of IC7006 become about 2.6V in the drum motor startup timing? YES Check the connection between connectors AD and ME. Replace the drum motor. Check IC2001 and replace as required. NO Are there the PWM output NO signals at pins (32) and (34) of IC2001? YES Check the line between pins (32)/(34) of IC2001 and pin (2) of IC7006. Check IC2001 and replace as required. 27DV-S100 27DV-CS10 FLOW CHART No. 2-4 FLOW CHART No. 2-7 FLOW CHART No. 2-9 Capstan motor failure to stop. Drum motor failure to stop. Is about 0.6V applied at pin NO (2) of IC7006? YES Is about 0V applied at pin (47) of IC2001? NO Check IC2001 and replace as required. NO FLOW CHART No. 2-8 Capstan motor failure to start. 63 Is 5V applied at pin (8) of connector AC? Check IC2001 and replace as required. FLOW CHART No. 2-10 No H.SW.P. output signal. NO Check the CAP5V line (around Q9103) and replace as required. NO Go to Flowchart No. 6 "Drum motor failure to start". Is there the drum PG signal NO at pin (66) of IC2001? Check the drum PG signal line between pin (7) of IC7006 and pin (66) of IC2001. Is the drum motor running? YES YES Is 23V applied at pin (5) of connector AC? NO Check R7054 and replace as required. Replace the capstan motor. Check R7059 and R7002. Is 0V applied at pin (29) of IC2001? YES YES YES Replace the drum motor. Is 0V applied at pin (4) of connector AC? NO Check the PC23V line. YES YES Is about 2.6V applied at pin NO (4) of connector AC? YES Are there the PWM NO output signals at pins (31) and (33) of IC2001? Check IC2001 and replace as required. YES Is there the drum FG signal NO at pin (65) of IC2001? YES Check the line between pins (31)/(33) of IC2001 and pin (4) of connector AC Is there the H.SW.P. signal at pin (23) of IC2001? NO Check the drum FG signal line between pin (8) of IC7006 and pin (65) of IC2001. Check IC2001 and replace as required. YES Is about 2.7V applied at pin NO (3) of connector AC? YES Check IC2001 and replace as required. Check the H.SW.P. signal line. YES Check R7032, R7034, R7035, R7036, R7037 and C7030. 27DV-S100 27DV-CS10 Check the connection between connectors AC and MC. Replace the capstan motor. Is 5V applied at pin (92) NO of IC2001? Are there the reference NO signals (14MHz) at pins (37) and (38) of IC2001? Insert a cassette tape and call the FF or REW mode. Are pulses coming out of the supply reel sensor (D7006) and take-up reel sensor (D7007)? YES Check the lines between the reel sensors and pins (3)/(2) of IC2001. FLOW CHART No. 2-13 Capstan servo malfunction. NO Check the reel sensors for stain and poor positioning. Check the clearance between the mechanism and main PWB. Replace the reel sensor(s) as required. YES Does the drum servo function? NO FLOW CHART No. 2-12 64 Are there the reference NO Check X7001, C7007 and signals (14MHz) at pins C7008 for malfunction. (37) and (38) of IC2001? YES Does the servo malfunction in YES Is there the composite NO the REC mode alone? (Make sync signal at pin (50) of recording and playback. Does IC2001? the switching point appear YES onscreen and slowly move?) NO Is there the H.SW.P. signal NO Go to Flowchart No. 10 "No H.SW.P. output signal". at TP3302? YES Is there the specified capstan FG signal at pin (67) of IC2001? YES NO YES Does the duty ratio of the drum error output at pins NO (32) and (34) of IC2001 change according to the rpm (by gently pressing on the drum motor)? YES Check the connection between pins (32)/(34) of IC2001 and pin (2) of IC7006, as well as the connection between IC7006 and drum motor. Replace the drum motor as required. Check the PC12V line. Check IC2001 and replace as required. YES Does the voltage at pin NO (4) of connector AC change according to the rpm? YES Replace the A/C head. Check the record control signal line. Check IC2001 and replace as required. NO Does the duty ratio of the capstan error output at pins (31) and NO (33) of IC2001 change according to the rpm (by gently pressing on the drum motor)? Check the connection between connectors AA and MH. Check the A/C head for height, stain, etc. Check the connection between connectors AC and MC. Replace the capstan motor. NO NO Check IC2001 and replace as required. Check the connection between connectors AA and MH. Check the A/C head for stain, height, breakage, etc. Replace as required. YES YES Are there the record control signals at pins (5) and (6) of connector AA? YES YES Does the PC12V line function? Is there the playback NO control signal at pin (76) of IC2001 during the play of the recorded tape? YES Are there the record control signals at pins (74) and (75) of IC2001 in the REC mode? Check the line between pin (52) of IC2201 and pin (50) of IC2001. Go to Flowchart No. 12 "Drum servo malfunction". YES Make recording on a NO tape with a welladjusted set, and play back the recording. Drum servo malfunction. Check X7001, C7007 and C7008 for malfunction. Is there the specified capstan FG signal at pin (6) of connector NO AC? YES Check IC2001 and replace as required. Check the line between pins (31)/(33) of IC2001 and pin (4) of connector AC. Check the line YES between pin (6) of connector AC and pin (67) of IC2001. Check the connection between NO connectors AC and MC. Replace the capstan motor. YES Check the line YES between pins (5)/(6) of connector AA and pins (74)/(75) of IC2001. 27DV-S100 27DV-CS10 FLOW CHART No. 2-11 No supply and take-up reel pulse output. FLOW CHART No. 2-14 Recording possible, but no colors. Video recoding (luminance) failure. Is there signal at pin (30) of IC2201? NO Is there signal at pin (41) of IC1301? YES YES NO Check the tuner/IF circuit (TU261) or J405, J401 and their peripheral parts. Check the line between pin (41) of IC1301 and pin (30) of IC2201. Is there the luminance NO input signal (about 0.5Vpp) at pin (19) of IC2201? Check the line between pins (18) and (19) of IC2201. (Check C2206.) Is 5V voltage applied at pin (61) of chroma power terminal IC2201? YES NO Check the peripheral circuits of pin (61) of IC2201 and the YC5V line. Check the line between pins (21) and (42) of IC2201. (Check C2208.) Is there the chroma input signal (about 143mVp-p /Burst) at pin (46) of IC2201? NO Check the line between pins (46) and (60) of IC2201. (Check C5512.) YES Is there the luminance NO input signal (about 0.3Vpp) at pin (42) of IC2201? YES Is there the luminance NO input signal (about 0.5Vpp) at pin (26) of IC2201? Check the line between pins (26) and (39) of IC2201. (Check C2212.) NO YES 65 Are there the I2C clock and data signals at pins (62) and (63) of IC2201? YES Replace IC2201. Is there the luminance output signal (about 0.5Vpp) at pin (39) of IC2201? Is 5V voltage applied at pins (12), (36), (38), (40), (41), (43), (61), (67), (90) and (96) of IC2201? YES Make sure oscillation (3.58MHz) occurs at pins (71) and (73) of IC2201. YES YES Is there signal at pin (52) of IC2201? YES YES NO Is there the chroma input signal (about 180mVp-p /Burst) at pin (58) of IC2201? NO YES YES NO Is 5V voltage applied at pin (36) of CCD power terminal IC2201? Check the YC5V line. Check the line between pins (35) and (58) of IC2201. (Check R5505 and C5515.) NO Is there the chroma output signal (about 180mVp-p/Burst) at pin (35) of IC2201? YES Make sure that the CCD clock signal (about 7.16MHz/0.5Vp-p) is applied from pin (69) to pin (44) of IC2201. NO Check the line between pins (62)/(63) of IC2201 and pins (57)/(56) of IC2001. Is there the luminance input signal (about 0.5Vpp) at pin (23) of IC2201? NO Check the line between pins (23) and (24) of IC2201. (Check C2210.) NO Check the peripheral circuits of pins (13) and (14) of IC2201. (Check R2201, R2202 and C2203.) YES Are there the luminance input and output signals (about 0.5Vp-p) at pins (13) and (14) of IC2201 respectively? YES SP mode: Are there the record FM output signals (about 20mAp-p) at pins (88), (89) and (SP1), as well as pins (86), (87) and (SP2) of IC2201? EP mode: Are there the record FM output signals (about 20mAp-p) at pins (93), (94) and (EP1), as well as pins (91), (92) and (EP2) of IC2201? NO Make sure that YC5V is applied at pin (90) of IC2201. 27DV-S100 27DV-CS10 YES Check the cylinder. Replace as required. Recording and playback possible, but no colors. Video playback failure. Is there the FM input signal (about 0.4Vp-p) at pin (78) of IC2201? NO YES Check the line between pins (78) and (79) of IC2201. Is 5V voltage applied at pin (61) of chroma power terminal IC2201? NO Check the peripheral circuits of pin (61) of IC2201 and the PC5V line. NO Check the line between pins (46) and (60) of IC2201. (Check C5512.) YES YES Is there the luminance output signal (about 0.4Vp-p) at pin (79) of IC2201? Is there the chroma input signal (about 403mVp-p/Burst) at pin (46) of IC2201? YES NO YES Is the V-H.SW.P. signal applied at pin (81) of IC2201? Make sure oscillation (3.58MHz) occurs at pins (71) and (73) of IC2201. NO Check the V-H.SW.P. signal line. Are there the luminance input and output signals (about 0.25Vp-p) at pins (13), (14) and (16) of IC2201 respectively? NO Is there the chroma input signal (about 508mVp-p/Burst) at pin (58) of IC2201? Check the peripheral circuits of pins (13), (14) and (16) of IC2201. (Check C2203, R2201, R2202, L2204, C2205 and R2203.) Is there the chroma output signal (about 286mVp-p/Burst) at pin (55) of IC2201? 66 Check the line between pins (18) and (19) of IC2201. (Check C2206.) YES YES Is there the chroma output signal (about 508mVp-p/Burst) at pin (35) of IC2201? NO Check the line between pin (55) of IC2201 and pin (5) of IC1301. (Check R5503 and C5510.) Check the line between pins (21) and (42) of IC2201. (Check C2208.) YES NO Is there the luminance input signal (about 0.5Vp-p) at pin (26) of IC2201? YES NO YES NO Is there the luminance input signal (about 0.3Vp-p) at pin (42) of IC2201? Check the line between pins (35) and (58) of IC2201. (Check R5505 and C5515.) YES YES NO Is there the luminance input signal (about 0.5Vp-p) at pin (19) of IC2201? NO Replace IC2201. Check the line between pins (26) and (39) of IC2201. (Check C2212.) YES Is there the luminance output signal (about 0.5Vp-p) at pin (39) of IC2201? NO Is 5V voltage applied at pin (36) of CCD power terminal IC2201? YES Is the CCD control voltage of about 5V applied to pin (37) of IC2201? Check to see if the CCD clock signal (about 7.16MHz/0.5Vp-p) is applied from pin (69) to pin (44) of IC2201. Is there the luminance input signal NO (about 0.5Vp-p) at pin (23) of IC2201? YES Replace IC2201. Check the line between pins (23) and (24) of IC2001. (Check C2210.) 27DV-S100 27DV-CS10 FLOW CHART No. 2-15 FLOW CHART No. 2-16 FLOW CHART No. 2-17 Hi-Fi audio recording failure. Are the following signals applied to the terminals of IC6651? L-ch NO Hi-Fi audio playback failure. Check the line between pins (38)/(40) of IC1301 and pins (14)/(9) of IC6651. YES R-ch Pin (14) Is there the playback envelope output NO signal (300mVp-p) at pin (29) of IC6651? Pin (9) YES Are 5V and 9V voltages applied at pins (40) and (58) of IC6651 respectively? Replace IC6651. YES NO Check the PC5V and PC9V regulator circuits. Replace IC6651. Is there the A-H.SW.P. input signal at pin (27) of IC6651? NO Check the A-H.SW.P. signal line between pin (27) of IC6651 and pin (26) of IC2001. YES Are there the audio output signals at pins (53) and (57) of IC6651? YES NO Are there the serial clock and data signals at pins (42) and (43) of IC6651? NO Check the line between pins (42)/(43) of IC6651 and pins (18)/(17) of IC2201. YES 67 Is the voltage at pin (28) of IC6651 at "H" level? NO Is there the sub-carrier input signal (3.58MHz, about 900mVp-p) at pin (45) of IC6651? NO Check the line between the emitter of Q5501 and pin (45) of IC6651. Replace IC6651. YES Is the REC AGC ADJ terminal voltage (1.7V) at pin (37) of IC6651 as specified? NO YES Is the voltage at pin (29) of IC6651 about 3.7V? NO Check the BIAS CTL line. Are there the record FM output NO signals from pin (21) to pin (24) of IC6651 for CH-1, and from pin (21) to pin (22) of IC6651 for CH-2? Is 5V voltage applied at pin (25) of IC6651? NO Check the connectors AH and MZ. Check the PC5V line. 27DV-S100 27DV-CS10 YES FLOW CHART No. 2-19 No recording with linear audio signal. Is there the audio input signal at pin (8) of IC2201? NO No playback with linear audio signal. Check the line between pin (61) of IC6651 and pin (8) of IC2201. YES Is the voltage at pin (99) of IC2201 at "L" level? Is there the audio signal (PB EQ) at pin (100) of IC2201? NO Do the MH-AA harness, playback amplifier and its peripheral circuits function? YES YES NO Check R6617. Is the A/C head dirty? YES YES Does the bias oscillation circuit function? NO NO Check the bias oscillation circuit (around T6601 and Q6602). YES YES Is there the bias signalNO superimposed audio signal at pin (4) of IC2201? Replace the A/C head. Check R6623, R6605, R6606 and C6606. YES 68 Check the AA-MH harness and the A/C head. Is the A/C head height optimally adjusted? Readjust the A/C head height. Is there the audio output signal at pin (11) of IC2201? YES NO Is the voltage at pin (99) of IC2201 at "L" level? NO Check R6617. Check the line between pin (11) of IC2201 and pin (62) of IC6651. Replace IC2201. 27DV-S100 27DV-CS10 FLOW CHART No. 2-18 FLOW CHART No.3-2 FLOW CHART No.3-1 Is the signal from the pins(70) and (69) of IC504 input into the pins(1) and (28) of IC7701? No Check the LD-RVS/FWD signal line between IC7701 and the IC504. Yes Does the optical pickup move up and down after the disc is removed? (Checking of symptom.) No Yes Check PC 8V line. Replace IC301. Yes No Is loading motor drive voltage output from the pins(9) and (10) of IC7701? No Yes Is 8V voltage applied to the pin(8) of IC7701? Yes Is FE signal output to the pin(21) of IC301 when the disc is set? No Yes No Check the line between the IC702 and the loading motor. Is there input signal on the pins(52), (53), (54) and (55) of IC301? No Yes Replace IC7701. Is the loading motor drive voltage applied to the terminal of loading motor? See FLOW CHART NO.6 Check the connection of optical pickup cable. Is FE signal inputted into the pin(150) of IC701? No Yes 69 Check for mechanism and gear engagement and breakage. Check or replace IC701. Check the line between the IC301 and IC701. 27DV-S100 27DV-CS10 TROUBLESHOOTING FLOWCHARTS OF DVD SECTION The [No Disc] indication. (In case of focus error) The disc tray cannot be opened and closed. FLOW CHART No.3-4 Both picture and sound do not operate normally.(1) The [No Disc] indication. (In case focus servo does not function.) Is the focus control signal output to the pin(158) of IC701? No Check the crystal oscillator at pin(11) of IC701 and its peripheral circuits. Set the disc on the disc tray. Yes Yes Is the focus control signal from the No pin(158) of IC701 input into the pin(23) of IC7701? Check the focus control signal line between the IC7701 and IC701. Do you have loading done the disk by No normality? Check the loading switch. Yes Yes Check PC 8V line. No Is the focus control drive voltage output No from the pins(17) and (18) of IC7701? Yes Is 8V voltage applied to the pin(8) of IC7701? Yes Check to see if the signal at pin(21) of IC7701 is at "H" level. If not, replace IC7701. Yes Is the focus control drive voltage applied to the terminal of focus actuator? Is the level of RF signal which is output No from pins(29), (30) of IC301, normal? No Check the line between the IC7701 and the focus actuator. Replace the main PWB unit. Yes See FLOW CHART NO.9 and NO.10. 70 Yes Check the connection of optical pickup cable. If it is normal, replace the traverse chassis unit. FLOW CHART No.3-5 The [No Disc] indication. (When the laser beam does not light.) Is the Q303(LD POWER CTL) drive output to the pin(46) of IC301? (Checking of symptom.) No Check the line between the pin(46) of IC301 and the base of Q303. Yes Is 5V voltage applied to the emitter of Q303? No Check the A_5V line. Yes Is approx. 2V applied to the pin(3) of the pickup terminal? (See note.) Yes Check the connection of optical pickup cable. If it is normal, replace the traverse chassis unit. No Check the line between the Q301, Q307 and pickup terminal. Note: Since the laser diode is very susceptible to static electricity, be careful of static electricity or electricity leak from the measuring equipment when confirming the voltage. Check for contamination of objective lens of optical pickup. Yes No Replace traverse chassis unit. 27DV-S100 27DV-CS10 FLOW CHART No.3-3 FLOW CHART No. 3-6 FLOW CHART No. 3-7 DVD picture failure DVD sound failure Place the disc on the disc tray and play it back. Place the disc on the disc tray and play it back. YES Is there the playback video signal at pin (1) of connector CN802 on the DVD main unit? NO Check the DVD main unit and DVD mechanism unit. YES Are there the playback video signal, luminance signal and chroma signal at pins (5), (1) and (3) of connector DA on the DVD sub unit? Are there the playback video signals at pins (27), (23) and (25) of IC1001? NO YES YES Are the signals at pins (7)/(8) and (1)/(3)/(28) of IC1001 at "H" and "5V" levels, respectively? NO YES 71 Are there the playback video signals at pins (53), (56) and (58) of IC1301? Check the lines between pins (9), (7) and (5) of connector CA on the DVD sub unit and pins (2), (6) and (4) of IC1001. YES NO Are there the playback audio signals at pins (13) and (16) of IC1101? Check the lines from pins (33) and (34) of IC1301 to pins (17) and (18) of IC2001. Check the line between pin (24) of connector CB and pin (2) of IC1101. YES Are there the playback audio signals at YES pins (52) and (54) of IC1301? NO 2 Are there the I C clock and data signals NO at pins (33) and (34) of IC1301? Check the lines from pins (13) and (16) of IC1101 to pins (3) and (5) of IC1102. Check IC1101 and its peripheral circuits. Check the lines from pins (7) and (9) of connector DA to pins (23) and (25) of IC1301. Check the lines between IC3001 and IC3201 of the TV section. Check the lines from pins (33) and (34) of IC1301 to pins (17) and (18) of IC2001. YES Check the PC9V line. Is the 9V supply voltage applied at pin (42) of IC1301? Replace IC1301. NO Check the PC9V line. 27DV-S100 27DV-CS10 YES Replace IC1301. Check IC1102 and its peripheral circuits. YES Are there the playback audio signals at pins NO (23) and (25) of IC1301 on the terminal unit? Check the lines from IC4401 thru IC1401 to IC8850 of the TV section. Check the line from pins (1) and (7) of IC1102 to pins (7) and (9) of connector DA. YES Is there the playback digital signal at pin (2) of IC1101? Check the lines between pins (5), (1) and (3) of connector DA and pins (22), (24) and (26) of IC1301. YES YES NO YES Is the 9V supply voltage applied at pin (42) of IC1301? NO NO Check IC1001 and its peripheral circuits. NO 2 Are there the I C clock and data signals NO at pins (33) and (34) of IC1301? Are there the playback audio signals at pins (1) and (7) of IC1102? Are there the playback audio signals at pins (3) and (5) of IC1102? NO YES YES Check the DVD main unit and DVD mechanism unit. YES NO Check the lines between pins (27), (23), and (25) of IC1001 and pins (5), (1) and (3) of connector DA. Are there the playback video signals at NO pins (22), (24) and (26) of terminal unit IC1301? YES Is there the playback audio signal at pin NO (6) of connector CN801 on the DVD main unit? YES Are there the playback audio signal at NO pins (7) and (9) of connector DA on the DVD sub unit? 27DV-S100 27DV-CS10 CHASSIS LAYOUT H G F E D C B A 1 2 3 72 4 5 6 7 8 9 10 11 73 12 27DV-S100 27DV-CS10 IC FUNCTION LIST OF DVD SECTION IC301 TA1323F RF PROCESSOR Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Terminal name GND P2TP P2TN LDO2 MDI2 VrD Vrfil Vdd DPAC DPBD DPD1 DPD2 SCB SCL SCD VRCK I/O – I I O I O – I – – – – I I I I Operation function GND terminal. TE+input (CD) TE–input (CD) Drive ouput 2 Monitor input 2 Digital VREF Filter capacity for reference Power terminal DPD AC combination capacity 1 DPD AC combination capacity 2 DPD integral capacity 1 DPD integral capacity 2 Control line (Bit clock) Control line (Latch signal) Control line (Sirial Data) Reference clock input 17 VCKF – 18 19 20 21 22 23 24 25 26 27 28 29 VccP LVL TEO FEO DFTN VccS NC RPZ RPO RPB RPP RFOn – O O O I – – O O – – O 30 RFOp O 31 32 33 VccR RFS TEB – I I Capacity for VRCK time constant adjustment Power terminal Servo addition output TE output FE output DPD difect Power terminal (servo) – RF ripple output 2 RF ripple output 1 RF ripple bottom RF ripple peak Equivalent RF output (Differential output) Equivalent RF output (Differential output) Power terminal (RF) RF slice level adjustment TE balance 34 FEB I FE balance VrD 35 DPDB I Pit depth adjustment VrD 36 37 38 39 40 41 42 43 Vcc2 NC NC GND2 TCC1 RFDC VrA EQB – – – – I – O I Power terminal – – GND terminal. Time constant adjustment DC feedback capacity Analog VREF Boost adjustment Terminal DC Voltage(TYP.) Remarks – VrA VrA – – – Vdd/2 output (1.65V) – – 3.3V is connected. – – – – 2.2[V] 2.2[V] 2.2[V] 2.3[V] When frequency is increased, the filters excepting the servo LPF are shifted to high frequency side. – – VrD/2 VrD VrD – – – VrD VrD/2 – – 1.65[V] 1.65[V] – – VrD – – – – – – 2.1[V] VrD 74 Low DPD output: Mute Used in the open state. DC voltage varies by RFS. DC voltage varies by RFS. When TEB is raised, the gain on the TP side and the delay amount on the A+C side are increased. Adjusting range: GND - Vdd When FEB is raised, the gain on the A+C (FP) side is increased. Adjusting range: GND - Vdd When DPDB is raised, the delay amount on the A•B side is increased. Adjusting range: GND - Vdd Used in the open state. Used in the open state. When EQB is raised, the boost increases. Adjusting range: GND - Vdd 27DV-S100 27DV-CS10 TEB P1TP • Block Diagram FEB A input (CD) B input (CD) C input (CD) D input (CD) GND terminal (Servo) FE+input (CD) FE–input (CD) DPDB I I I I – I I Vcc2 P2AI P2BI P2CI P2DI GNDS P2FP P2FN NC 58 59 60 61 62 63 64 NC D input (DVD) C input (DVD) B input (DVD) A input (DVD) GND terminal (RF) APC polarity 2 GND2 I I I I – I TCC1 P1DI P1CI P1BI P1AI GNDR LDP2 VrA 52 53 54 55 56 57 EQF Monitor input 1 Drive output 1 TE–input (DVD) TE+input (DVD) FE–input (DVD) FE+input (DVD) APC polarity 1 MDI1 I O I I I I I LDO1 MDI1 LDO1 P1TN P1TP P1FN P1FP LDP1 P1TN 45 46 47 48 49 50 51 Terminal DC Voltage(TYP.) Remarks VrD When EQF is raised, shift to the high frequency side occurs. Adjusting range: GND - Vdd – – VrA VrA VrA VrA – Positive polarity when this terminal is connected to Vcc. VrA VrA VrA VrA – – Positive polarity when this terminal is connected to Vcc. VrA VrA VrA VrA – VrA VrA RFDC I/O Operation function I Frequency adjustment EQB Pin No. Terminal name 44 EQF 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 LDP1 51 P1DI 52 P1CI 53 P1BI 54 sel-RF sel-PD F-gain Adjust GNDR 56 LDP2 P2BI 59 P2DI 28 RPP 27 RPB RF Ripple creation 26 RPO FEB sel-FE 57 58 F-gain Adjust sel-PD DPDB sel-TE sel-DPD 60 sel-PD T-gain Adjust GNDS 62 23 VccS mode-TE 18 VccP 17 VCKF 3 4 5 6 7 8 9 10 11 12 13 14 15 16 LDO2 MDI2 VrD Vrfil Vdd DPAC 75 DPD1 2 DPBD 1 P2TN BUS P2TP 64 19 LVL Time constant adjustment TCC1 Vref 20 TEO GND P2FN 21 FEO Level detect tcc1 (BUS) 63 22 DFTN TE-gain Adjust TEB sel-LVL APC2 24 NC TEB VrA P2FP 25 RPZ FE-gain Adjust DPD-TE creation 3Beam-TE creation 61 29 RFOn EQ FE creation P2AI P2CI DC FB R-gain Adjust mode-IC 55 30 RFOp Output Amp DPD2 P1AI 31 VccR VRCK 50 SCD P1FP 32 RFS APC1 SCL 49 SCB P1FN 27DV-S100 27DV-CS10 IC501 IX1689GE Pin No. Symbol 45 DQ15/A-1 25-18, 8-4 A0-A12 3-1, 48, 16, 17 29, 31, 33, 35, 38, 40, 42, 44 30, 32, 34, 36, 39, 41, 43, 45 DQ8-DQ14 26 CE# 12 RP# 28 OE# 11 WR# 14 WP# 15 RY/BY# 47 BYTE# 13 37 27, 46 9, 10 Vpp Vcc GND NC A13-A18 DQ0-DQ7 FLASH MEMORY Type Name and function Byte selection address: When the device is in the x8 mode, the low or high order byte is Input selected. It is not used in the x16 mode. (If BYTE# is high, DQ15/A-1 input circuit does not operate.) Word selection address: Selection of one word of 16k byte block. These addresses are Input latched during data wiring operation. Block selection address: Selection of 1/32 erase block. These addresses are latched Input during data writing, erasing and lock block operation. Low order byte data input/output: Command user interface writing cycle data and command Input/Output input. Various data read memory identifier and status data output Chip nonselection or output disable: Float state High order byte data input/output: The function is the same as that of low order byte Input/Output data input/output. Operative only in x16 mode. x8 mode: Float state DQ15/A-1 is address. Chip enable: Device control logic, input buffer, decoder and sense amp. are activated. Input Chip becomes active only when CE# is “Low”. Reset/Power down: If RP# is set to “Low”, the control circuit is initialized when power is turned on. Hence, the RP#pin is set to “Low”. When power is turned on or off or in case of fluctuation it is kept at “Low” so as to protect data from noise. When RP# is in Input “Low” state, the device is in deep power down state. 480 ns is required to recover from the deep power down state. If the RP# pin becomes “Low”, the whole chip operation is interrupted and reset. After recovery the device is set to array read state. Output enable: When OE# is set to “Low”, data is output from the DQ pin. When OE# is Input set to “High”, the DQ pin is set to float state. Write enable: Command user interface, data Q register and address Q latch access is Input controlled. In “Low” state WR# becomes active. At rise edge the address and data are fetched. Write protection: Blanking/writing to the boot block area is input of prohibition control. Input Blanking to the boot block area and writing actuation can't be executed at the time of WP#=VIL. Ready/busy: The state of internal write state machine is output. In “Low” state it is indicated that the write state machine is in operation. If the write state machine waits for Output next operation instruction, erase is suspended or it is in deep power down state, the RY/BY# pin is in float state. Byte enable: When BYTE# is set to “Low”, the device is set to the x8 mode. At this time Input the DQ8-DQ15 pin becomes float state. Address A-1 selects high order/low order byte. When BYTE# is “High”, the device is set to the x16 mode. The A-1 input circuit is disabled. ——— Write/erase power supply: 5.0 ± 0.5V is applied during writing/erasing. ——— Device power supply: 5.0 ± 0.5V ——— Ground ——— Nonconnection 76 27DV-S100 27DV-CS10 • Block Diagram DQ8-14 DQ0-7 Output Buffer Output Buffer Input Buffer Input Buffer OUTPUT MULTIPLEXER I/O Logic BYTE# DATA QUEUE REGISTER ID Register CSR Register CE# ESRs CUI A-1.0~18 OE# Data Comparator WR# RP# Input Buffer Y-DECODER Y GATING/SENSING WSM 16-KBYTE Block 31 16-KBYTE Block 30 16-KBYTE Block 1 X-DECODER 16-KBYTE Block 0 RY/BY# ADDRESS QUEUE LATCHES Program Erase Voltage Switch VCC GND ADDRESS COUNTER IC502 IX1765GE VPP 4M EDO DRAM Terminal Terminal name 16-19, 22-26 A0-A8 Address inputs. Function 14 RAS Row address strobe. 28 UCAS 29 LCAS 13 WE Column address strobe/upper byte control. Column address strobe/lower byte control. Write enable. 27 OE 2-5, 7-10 DQ1-DQ16 Data inputs/outputs. Output enable. VCC +3.3V power supply. 21, 35, 40 VSS 0V ground. 11-12, 15, 30 NC No connection. 31-34, 36-39 1, 6, 20 • Block Diagram OE WE UCAS LCAS RAS RAS clock generator CAS clock generator WE clock generator OE clock generator VCC VSS Data I/O Bus Column decoders Refresh counter Sense amplifiers Y0-Y8 9 A0 A1 A7 A8 Address buffers and predecoders I/O Buffer 512 16 Row decoders X0-X8 512 77 Memory array I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 I/O16 27DV-S100 27DV-CS10 IC504 IX1687GE MICRO COM. PD7/D15 PD6/D14 PD5/D13 PD4/D12 PD3/D11 PD2/D10 PD1/D9 PD0/D8 PE7/D7 PE6/D6 PE5/D5 PE4/D4 PE3/D3 PE2/D2 PE1/D1 PE0/D0 Vcc Vcc Vcc Vcc Vcc Vss Vss Vss Vss Vss Vss Vss Vss • Block Diagram Port B Port C Bass Controller Peripheral address bus Port F D/A converter A/D converter Port 2 78 Port 4 Vref AVcc AVss Port 1 P47/AN7/DA1 P46/AN6/DA0 P45/AN5 P44/AN4 P43/AN3 P42/AN2 P41/AN1 P40/AN0 PPG Port 3 TPU PA7/A23/IRQ7 PA6/A22/IRQ6 PA5/A21/IRQ5 PA4/A20/IRQ4 PA3/A19 PA2/A18 PA1/A17 PA0/A16 PB7/A15 PB6/A14 PB5/A13 PB4/A12 PB3/A11 PB2/A10 PB1/A9 PB0/A8 PC7/A7 PC6/A6 PC5/A5 PC4/A4 PC3/A3 PC2/A2 PC1/A1 PC0/A0 P35/SCK1 P34/SCK0 P33/RxD1 P32/RxD0 P31/TxD1 P30/TxD0 Port 5 SCI P10/PO8/TIOCA0/DACK0 P11/PO9/TIOCB0/DACK1 P12/PO10/TIOCC0/TCLKA P13/PO11/TIOCD0/TCLKB P14/PO12/TIOCA1 P15/PO13/TIOCB1/TCLKC P16/PO14/TIOCA2 P17/PO15/TIOCB2/TCLKD P20/PO0/TIOCA3 P21/PO1/TIOCB3 P22/PO2/TIOCC3 P23/PO3/TIOCD3 P24/PO4/TIOCA4 P25/PO5/TIOCB4 P26/PO6/TIOCA5 P27/PO7/TIOCB5 P67/CS7/IRQ3 P66/CS6/IRQ2 P65/IRQ1 P64/IRQ0 P63/TEND1 P62/DREQ1 P61/TEND0/CS5 P60/DREQ0/CS4 WDT RAM Port G PG4/CS0 PG3/CS1 PG2/CS2 PG1/CS3 PG0/CAS DMAC ROM * Port 6 PF7/Ø PF6/AS PF5/RD PF4/HWR PF3/LWR PF2/LCAS/WAIT/BFEQO PF1/BACK PF0/BREQ DTC Peripheral data bus Interruption controller Internal data bus H8S/2000 CPU Internal addressbus Clock oscillator MD2 MD1 MD0 EXTAL XTAL STBY RES WDTOVF NMI Port E Port A Port D P50 P51 P52 P53/ADTRG 27DV-S100 27DV-CS10 IC508 IX1761GE Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 TRACK BUFFER INTERFACE Terminal name VDD1 HADR0 HADR1 HADR2 HADR3 HADR4 HADR5 HADR6 HADR7 VSS VDD1 HDAT0 HDAT1 HDAT2 HDAT3 HDAT4 HDAT5 HDAT6 HDAT7 HRD HWR HAS HCS1 HCS2 VSS VDD1 HWAIT HINT VSS PDO[0] PDO[1] PDO[2] PDO[3] PDO[4] PDO[5] PDO[6] PDO[7] PDO[8] VSS VDD1 PSYCO PDRQO PDCKO VSS VDD2 DVDREQ PDCKI PDRQI PSYCI VSS VDD2 I/O Supply Input Input Input Input Input Input Input Input Supply Supply In/Output In/Output In/Output In/Output In/Output In/Output In/Output In/Output Input Input Input Input Input Supply Supply Output Output Supply Output Output Output Output Output Output Output Output Output Supply Supply Output Output Output Supply Supply Input Input Input Input Supply Supply Operation function Digital power supply +3.3V CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus Digital GND Digital power supply +3.3V CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Data bus CPU Read signal CPU write signal CPU address strobe CPU chip select signal 1 (Track Buffer Operation) CPU chip select signal 2 (bus Voltage Transfer) Digital GND Digital power supply +3.3V CPU wait signal (Open drain) CPU interrupt signal (Open drain) Digital GND Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Output DVD/CDdata Digital GND Digital power supply +3.3V Output data selector sync signal Output data transfer block signal Output data transfer clock Digital GND Digital power supply +5V Request signal input Input data transfer clock Input data transfer block signal Input data selector sync signal Digital GND Digital power supply +5V 79 27DV-S100 27DV-CS10 Pin No. 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Terminal name PDI[8] PDI[7] PDI[6] PDI[5] PDI[4] PDI[3] PDI[2] PDI[1] PDI[0] VSS VDD1 VSS VDD2 5VBUS[7] 5VBUS[6] 5VBUS[5] 5VBUS[4] 5VBUS[3] 5VBUS[2] 5VBUS[1] 5VBUS[0] NC NC VSS VDD1 5VBUFO[B] 5VBUFI[B] 5VBUFO[A] 5VBUFI[A] GPO[3] GPO[2] GPO[1] GPO[0] VSS VDD1 LI[1] LI[2] BUFO[C] BUFI[C] BUFO[B] BUFI[B] BUFO[A] BUFI[A] TEST0 TEST1 TEST2 NC MRST VSS I/O Output Output Output Output Output Output Output Output Output Supply Supply Supply Supply In/Output In/Output In/Output In/Output In/Output In/Output In/Output In/Output – – Supply Supply Output Output Output Output Output Output Output Output Supply Supply Input Input Output Input Output Input Output Input Input Input Input – Input Supply Operation function Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Input DVD/CD data Digital GND Digital power supply +3.3V Digital GND Digital power supply +5V CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output CPU bus 5V conversion input/output Not Connect Not Connect Digital GND Digital power supply +3.3V 5V buffer output B 5V buffer input B (3.3V input) 5V buffer output A 5V buffer input A (3.3V input) General-purpose output terminal (CPU control) General-purpose output terminal (CPU control) General-purpose output terminal (CPU control) General-purpose output terminal (CPU control) Digital GND Digital power supply +3.3V Gate Input[1] Gate Input[2] Schmitt trigger buffer output C Schmitt trigger buffer input C Schmitt trigger buffer output B Schmitt trigger buffer input B Schmitt trigger buffer output A Schmitt trigger buffer input A Test terminal 0 (Normal: Low, Test: Hi) Function Test terminal 1 (Normal: Low, Test: Hi) RAM Test terminal 2 (Normal: Low, Test: Hi) Pin Not Connect 27MHz Input terminal Digital GND 80 27DV-S100 27DV-CS10 VDD2 PDI[8] PDI[7] PDI[6] PDI[5] PDI[4] PDI[3] PDI[2] PDI[1] VSS PDI[0] VSS VDD1 VDD2 5VBUS[7] 5VBUS[6] 5VBUS[5] 5VBUS[4] 5VBUS[3] 5VBUS[2] 5VBUS[1] NC 5VBUS[0] NC VSS • Block Diagram 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 76 50 VSS 5VBUFO[B] 77 49 PSYCI VDD1 5VBUFI[B] IPD Interface 78 48 PDRQI 47 5VBUFO[A] 79 PDCKI Timing Gen. 46 DVDREQ 5VBUFI[A] 80 GPO[3] 81 GPO[2] 82 GPO[1] 83 GPO[0] 84 VSS 85 VDD1 86 40 VDD1 LI[1] 87 39 VSS LI[2] 88 BUFO[C] 89 BUFI[C] 90 BUFO[B] 91 BUFI[B] 92 BUFO[A] 93 BUFI[A] 94 32 PDO[2] TEST0 95 31 PDO[1] TEST1 96 30 PDO[0] TEST2 97 NC 98 MRST 99 VSS 100 GPO Interface ID Detect Error Detect 45 VDD2 44 VSS 43 PDCKO Memory CTL 42 PDRQO 41 PSYCO 38 PDO[8] RAM (4.2Kbyte) ZZ 37 PDO[7] OPD Interface 36 PDO[6] ZZ ZZ 35 PDO[5] 34 PDO[4] 33 PDO[3] Host Interface 29 VSS 28 HINT 27 HWAIT HADR7 VSS HADR6 HCS2 HADR5 HCS1 HADR4 HAS HADR3 HWR HADR2 HRD HADR1 HDAT7 VDD1 81 HDAT6 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 HDAT5 8 HDAT4 7 HDAT3 6 HDAT2 5 HDAT1 4 HDAT0 3 VDD1 2 VSS 1 HADR0 26 VDD1 27DV-S100 27DV-CS10 IC601 IX1720GE AV DECODER • Terminal description Name Type Description Host interface, CD-DSP interface, sub-code interface (32-pin) Reset input (active Low). When shifting from the assert state to deassert state, RESET# ID initialization process of this device is started. Stand-by input (active Low). When asserting with RESET#, all of output pins and bidirectional pins enter the float state, and this device is electrically separated from STANDBY# ID periphery. All internal operations are stopped and the power consumption is minimized. In the stand-by mode, the contents of SDRAM and setup parameter are not retained. Idle, Init, or Reset state display output (active High). It enters the active state after IDLE O(p.u.) resetting. Data bus width of the host interface is determined. It can be changed during resetting HWID ID only. The host interface of the device is set to 8 bits at the low level (GNDP) and 16 bits at the high level (VDDP). When the width is 16 bits (HWID is VDDP), byte order of the host interface data bus is determined. It can be changed during resetting only. The device is set to input/ HORD ID output m.s. byte HD at [15:8] at the low level (GNDP), and m.s. byte at [7:0] at the high level. When HWID is at the GNDP level, it is connected to GNDP. Protocol of the host bus is determined. It can be changed during resetting only. The HTYPE ID device is set to A type at the low level (GNDP) and B type at the high level (VDDP). HD[7:0] I/O 8 I.s. of the host data bus. When HWID input is connected to GNDP, only this signal (HD[7:4]) (r.t.) is defined as the host data signal. When HWID is connected to VDDP, it is used as (HD[3]) (p.u.) an 8 I.s. line of 16-bit data bus. (HD[2:1]) (r.t.) (HD[0]) (p.u.) HD[11:8] I/O When HWID is connected to VDDP, it is used as a data line 11:8 of the 16-bit host (HD[11]) (p.d.) data bus. (HD[10:8]) (r.t.) When HWID is connected to VDDP, it is used as a data line 15:12 of the 16-bit host HD[15:12] I/O(r.t.) data bus. When HWID is connected to GNDP, it is used as a the CD-DSP serial input port pin as defined below. CDCLK (HD[12]) I CD-DSP bit clock input CDDAT (HD[13]) I CD-DSP data input CDFRM (HD[14) I CD-DSP LR clock (frame) input CDERR (HD[15]) I CD-DSP data error input Host address input. The address signal specifying the physical address in this device HA[3:0] I is input. HCS# I Host chip select input. Active Low. Host protocol A type (HTYPE=GNDP): HR/W#. This input determines the direction of HWR# (HR/W#) I the host access. Host protocol B type (HTYPE=VDDP): HWR#. Host write input (active Low). Host protocol A type (HTYPE=GNDP): HDS#. Data strobe input (active Low). HRD# (HDS#) I \Host protocol B type (HTYPE=VDDP): HRD#. Host read input (active Low). Glossary I AI ID r.t. Input Analog input Input not synchronized with PCLK Retained terminal O AO p.u. Output Analog output Terminal internally pulled up 82 I/O AI/O p.d. Bidirectional Analog bidirectional Terminal internally pulled down 27DV-S100 27DV-CS10 Name Type Description Host interface, CD-DSP interface, sub-code interface (32-pin)...continued Host ready output (active High). Use this signal when the stream is transferred via the host bus. External pull-up resistor is required. Prior to transfer of each packet (1 HRDY O(p.d.) packet: length in CodBurstLen bytes), make sure that this signal is in the active state, and then bit streams of CodBurstLen byte long or shorter can be written on this device consecutively. Interrupt request (active Low). This is deasserted when the host reads the interrupt status register of this device and also when the host masks or resets the interrupt HIRQ# O(p.u.) using the interrupt mask register. When HIRQ# is not asserted, it enters the 3-state mode. (External pull-up resistor is required.) Host acknowledge output (active Low). When the protocol is A type, the device asserts this output and notifies the completion of read or write cycle. HACK# O(p.u.) When this signal is not active, it enters the 3-state mode. (External pull-up resistor is required.) When the protocol is B type, this signal functions as a wait output signal. If the high-speed host (microcomputer) is used, this signal may not have to be connected. GPI/O signal (3-pin) General-purpose bidirectional pin monitored and controlled by the ADP micro code. GPIO I/O(r.t.) After resetting, this pin is defined as an input. It can be set by using the ADP command. GPSI I General-purpose input monitored by the DVP micro code. General-purpose output controlled by the DVP micro code. After resetting, output GPSO O(p.d.) from this pin is switched to Low. PLL signal (5-pin) GCLK ID 27,000 MHz clock or crystal input for main processor. GCLK1 ID 27,000 MHz master clock input for audio. Normally, this must be connected to GCLK. Output to crystal connected to GCLK. If the crystal is not used for GCLK, nothing XO AO must be connected to XO. PLL configuration input. It can be changed only during resetting. Normally, both pins PLLCFG[1:0] ID must be connected to GNDP. Analog video port (7-pin) For CVBS, the composite video signal is output. CVBS/G/Y AO For RGB, the G signal is output. (DAC A) For YUV, the Y signal is output. For CVBS, the Y signal is output. Y/R/V AO For RGB, the R signal is output. (DAC B) For YUV, the V signal is output. For CVBS, the C signal is output. C/B/U AO For RGB, the B signal is output. (DAC C) For YUV, the U signal is output. CVBS/C AO The CVBS or C signal is selected and output. (DAC D) RSET AI Resistance load for DAC gain adjustment is inserted between GND and DAC. VREF AI Reference voltage for DAC gain adjustment is input. Composite sync output. Effective only when the RGB analog output is selected. COSYNC O(p.d.) Otherwise, it is fixed to Low. Digital video port (5-pin) VCLKx2 I/O(r.t.) Main video clock input or output. 27,000 MHz. VCLK I/O(r.t.) Divided VCLKx2 signal. Used as a qualifier of data and sync signal. HSYNC I/O(r.t.) Horizontal sync bidirectional signal pin. Its polarity and length are programmable. VSYNC I/O(r.t.) Vertical sync bidirectional signal pin. Its polarity and length are programmable. FI I/O(r.t.) Field identification bidirectional signal pin. Its polarity is programmable. 83 27DV-S100 27DV-CS10 Name Type Digital audio port (8-pin) Description AMCLK I/O(p.u.) Audio master clock I/O. Sampling frequency can be selected among 384fs, 256fs, 192fs, and 128fs (programmable). S/PDIF (AOUT[3]) O(p.d.) S/PDIF transmitter output. It can be connected to DAC as the fourth audio output (AOUT [3]). After resetting, this pin outputs the low-level signal. AOUT[2:0] O(p.d.) Serial output of PCM stereo audio for DAC. After resetting, this pin outputs the lowlevel signal. AIN I ALRCLK O(p.d.) ABCLK O(p.d.) Serial input of PCM stereo audio for ADC. LR clock output of AOUT [4:0] and AIN. The square wave is formed with the sampling frequency. The LR polarities are programmable. Bit clock output of AOUT [4:0] and AIN. AOUT is output to this clock in the leading and trailing edges (programmable) and AIN is latched. DVD-DSP interface (13-pin) DVDREQ DVDVALID DVDSOS DVDDAT[7:0] DVDSTRB DVDERR O(p.d.) I I I ID I DVD-DSP data request output (polarity programmable). DVD-DSP data effective input (polarity programmable). DVD-DSP data sector start input (polarity programmable). DVD-DSP data input bus. DVD-DSP data bit strobe (clock) input. Polarity programmable. DVD-DSP error input. Polarity programmable. SDRAM interface (35-pin) RAMDAT [15:0] I/O(r.t.) SDRAM bidirectional data bus. RAMADD [11:0] RAMRAS# O(p.d.) O(p.u.) SDRAM address bus output. SDRAM row selection (active Low) output. RAMCAS# PCLK O(p.u.) O(p.d.) SDRAM column selection (active Low) output. SDRAM clock output (same as the internal processing clock). RAMDQM RAMCS0# RAMCS1# O(p.d.) O(p.u.) O(p.u.) SDRAM data masking (active High) output. SDRAM chip select (active Low) output. Lower 2 Mbyte device. SDRAM chip select (active Low) output. Upper 2 Mbyte device. RAMWE# TEST signal (pin 3) O(p.u.) SDRAM write enable (active Low) output. SCNENBL TESTMODE ID ID Test pin. Normally connected to GNDP. Test pin. Normally connected to GNDP. ICEMODE Power signal (49-pin) ID Test pin. Normally connected to VDDP. GNDP VDDP S S Ground for 3.3V digital power supply. 3.3V digital power supply VDDIP GNDAAM S S 3.3V digital power supply Ground for PLL power supply for 3.3V AMCLK generation. VDDAAM GNDC S S PLL power supply for 3.3V AMCLK generation. Ground for 1.8V digital power supply. VDDC GNDA S S 1.8V digital power supply. Ground for PLL power supply for 1.8V internal clock generation. VDDA VDDD S S PLL power supply for 1.8V internal clock generation. Analog power supply for 3.3V video DAC. GNDDAC [D,B,P,S] S Ground for Analog power supply for 3.3V video DAC. 84 27DV-S100 27DV-CS10 90 100 80 130 70 TOP VIEW 140 60 150 50 40 30 20 10 1 160 HORD HWID VDDP HTYPE HD15/CDERR HD14/CDFRM HD13/CDDAT HD12/CDCLK HD11/TCK GNDP HD10/TMS VDDC HD9/TDO GNDC HD8/TDI VDDP HD7 HD6 VDDIP HD5 HD4 HD3 HD2 HD1 HD0 VDDP HA3 HA2 HA1 HA0 HWR#/HDS# HCS# VDDC HRD#/HDS# GNDC HRDY HIRQ# VDDP HACK# GNDP VDDA STNDBY# GNDA RESET# SCNENBL VDDP VCLKx2 GNDP TESTMODE VDDAAM AMCLK GNDAAM S/PDIF/AOUT3 GPIO VDDP AOUT0 AOUT1 AOUT2 ALRCLK VDDP ABCLK VDDC GPSO GNDC GPSI GNDP DVDERR DVDSOS DVDVALID DVDSTRB DVDREQ DVDDAT0 DVDDAT1 DVDDAT2 DVDDAT3 DVDDAT4 DVDDAT5 DVDDAT6 DVDDAT7 IDLE 110 120 GCLK XO PLLCFG0 GCLK1 VDDC PLLCFG1 GNDC AIN ICEMODE VREF GNDDAC_S GNDDAC_P RESET GNDDAC_B C/B/UDAC_C Y/R/VDAC_B VDDD CVBS/C/DAC_D CVBS/G/Y/DAC_A GNDDAC_D COSYNC VDDIP VDDP GNDP FI HSYNC VDDP VSYNC VCLK RAMDAT0 RAMDAT15 VDDP RAMDAT1 RAMDAT14 GNDP RAMDAT2 RAMDAT13 VDDP RAMDAT3 RAMDAT12 • Block Diagram 85 GNDP RAMDAT4 RAMDAT11 VDDP RAMDAT5 RAMDAT10 RAMDAT6 GNDC RAMDAT9 VDDP RAMDAT7 GNDP RAMDAT8 VDDP PCLK GNDP RAMDQM VDDC RAMWE# RAMCAS# RAMRAS# RAMCS1# VDDP RAMCS0# GNDP RAMADD11 RAMADD9 RAMADD10 VDDP RAMADD8 RAMADD0 GNDP RAMADD7 RAMADD1 RAMADD6 RAMADD2 VDDP RAMADD5 RAMADD3 RAMADD4 27DV-S100 27DV-CS10 IC602-3 IX3455CE 16M SDRAM Pin No. 35 34 18 19 20~24 27~32 17, 16, 15 Terminal Name CLK Clock Name CKE Clock Enable CS BS A0~A10 Chip Select Bank Address Address Input Function The system clock input. All other inputs are referenced to the SDRAM on the rising edge of CLK. Controls internal clock signal and when deactivated, the SDRAM will be one of the states among power down, suspend or self refresh. Command input enable or mask except CLK, CKE and DOM Select either one of banks during both RAS and CAS activity. Row Address: RA0~RA10, Column Address: CA0~CA7 RAS, CAS, WE Row Address Strobe, Column Address Strobe, Write Enable 14, 36 DOML, DOMU Data Input/Output Mask 2, 3, 5, I/O0~15 Data Input/Output 6, 8, 9, 11, 12, 39, 40, 42, 43, 45, 46, 48, 49 VCC/VSS Power Supply/Ground 1, 25, 26 4, 7, 10, VCCO/VSSO Data Output Power/Ground 13, 38, 41, 44, 47, 50 33, 37 NC No Connection RAS, CAS and WE define the operation. Refer function truth table for details. DOM control output buffer in read mode and mask input data in write mode. Multiplexed data input/output pin Power supply for internal circuit and input buffer. Power supply for DO No connection • Block Diagram Row Decoder Ref. Addr.[0:11] Address[0:10] Refresh Counter Audio/Self Refresh Refresh Interval Timer Row Addr. Latch/Predecode Self Refresh Counter 512Kx16 Bank 0 Sense AMP & I/O gates Column Decoder Precharge CKE CS RAS CAS State Machine BS(A11) Row Active Address Register Column Active Burst Length Counter Overflow Row Addr. Latch/Predecode WE Column Addr. Latch & Counter DOMU DOML Mode Register Column Decoder Sense AMP & I/O gates 512Kx16 Bank 1 Test Mode 86 Data Input/Output Buffers CLK I/O Control I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 27DV-S100 27DV-CS10 IC701 TC94A03F SERVO/DATA PROCESSOR Pin No. Terminal Name In/Output 1 ASLCN Output 2 ASLCO Output 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 DVSS RO DVDD DVR LO DVSS XVSS XI XO XVDD TESM0 TESM1 TESM2 VDD3 VSS3 VPFC – Output – Output Output – – Input Output – – – – – – Output 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 TEST0 VLPFI VLPFO VSS3 MON0 MON1 MON2 MON3 MON4 MON5 MON6 MON7 MON8 MON9 VDD3 NC NC TEST1 FLGA FLGB VSS3 /RST /MA /MRD /MWR /MCE /MINT MD0 MD1 MD2 MD3 MD4 MD5 MD6 MD7 VDD5 Input Input Output – Operation function 3/5V system Data slice negative pole output 3V system Analog data slice output 3V system (Digital slice output enabled at differential input) Ground for DAC only – R-ch output signal 3V system Power supply for DAC only 3V system Amplifier reference signal output 3V system L-ch output signal 3V system Ground for DAC only – Ground for oscillator only – Crystal oscillation input 3V system Crystal oscillation output 3V system Power supply for oscillator only – Test terminal 3V system Test terminal 3V system Test terminal 3V system 3.3V digital power – 3.3V digital ground – Clock PLL system phase/frequency 3V system comparative output Test mode terminal 3V system VCO system filter input for clock PLL 3V system VCO system filter output for clock PLL 3V system 3.3V digital ground – Output Test monitor – Analog output terminal Analog input terminal Analog output terminal Analog input terminal Analog output terminal Connected to GND OPEN Connected to VDD3 Analog output terminal Connected to VDD3 Analog input terminal Analog output terminal 3V system 3.3V digital power – – – Input In/Output In/Output – Input Input Input Input Input Output Test mode terminal General-purpose I/O or flag monitor General-purpose I/O or flag monitor 3.3V digital ground Reset terminal Microcomputer address enable signal Microcomputer data read signal Microcomputer data write signal Microcomputer chip enable signal Microcomputer interrupt signal 3V system 5V system 5V system – 5V system 5V system 5V system 5V system 5V system 5V system In/Output Microcomputer data buss 5V system – Remarks Analog output terminal Analog output terminal 5V power supply – 87 Connected to VDD3 Pull-up resistor built in Fail-safe terminal Fail-safe terminal Fail-safe terminal Fail-safe terminal Open drain terminal 27DV-S100 27DV-CS10 Pin No. 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 Terminal Name In/Output NC – NC SMCK Output VMCK Output VDD3 PD0 VSS5 PD1 PD2 PD3 PD4 VSS3 PD5 PD6 PD7 PD8 /PSYC /PDRQ PDCK VDD5 TESM3 DIGI TESM4 VDD3 BA0 BA1 BA2 BA3 VSS5 BA4 BA5 BA6 BA7 BA8 VDD3 /BOE /BRAS /BCAS /BCASL /BWE VDD5 BD0 BD1 BD2 BD3 BD4 BD5 BD6 BD7 BD8 VSS3 BD9 BD10 BD11 BD12 VSS5 Operation function 3/5V system – 5V system 5V system – Output – 22M system clock output Data output system (signal processing system) clock output 3.3V digital power supply DVD/CD data output 5V ground supply Output DVD/CD data output 5V system – 3.3V digital ground – 5V system – – Output DVD/CD data output 5V system Output Output Output – – Input – – DVD data sector sync signal DVD data transfer block DVD data transfer block 5V power supply Test terminal 1 bit DAC digital IN input Test terminal 3.3V digital power supply 5V system 5V system 5V system – 5V system 5V system 5V system – Output External RAM address output 5V system – 5V ground supply – Output External RAM address output 5V system – Output Output Output Output Output – 3.3V digital power supply External RAM/OE signal External RAM/RAS signal External RAM/UCAS signal External LCAS/WE signal External RAM WE signal 5V power supply – 5V system 5V system 5V system 5V system 5V system – External RAM data I/O 5V system In/Output – In/Output – Remarks 3.3V digital ground – External RAM data I/O 5V ground supply 5V system – 88 Connected to VSS5 Connected to VDD5 27DV-S100 27DV-CS10 Pin No. 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 Terminal Name In/Output BD13 BD14 In/Output BD15 NC – NC VDD3 – PLCK In/Output TESM5 – TESM6 – TESM7 – TESM8 – VSS3 – CFC1 Output CFC2 Output PPW Output 126 PESV Input 127 128 PVSS PESP – Output 129 PDOP1 Output 130 PDON1 Output 131 PDOP2 Output 132 PDON2 Output 133 134 135 LPFN LPFO PVREF Input Output – 136 137 138 139 VCOREF VCOF PVDD RFOn 140 141 142 TESM9 TEST2 RFCD – Input Input 143 RFDVD Input 144 145 AVDD RFCT – Input 146 147 RFZI TEZI Input Input 148 149 150 151 152 153 154 155 AWIN AVSS FEI TEI LVL RFRP AVSS TESM10 Input – Input Input Input Input – – Input Input – In/Output Operation function External RAM data I/O 3/5V system Remarks 5V system – 3.3V digital power supply PLL system clock I/O Test terminal Test terminal Test terminal Test terminal 3.3V digital ground VCO frequency control signal VCO frequency control signal Phase comparator offset adjustment voltage output Phase comparator offset adjustment signal input Ground for 3.3V PLL system only Phase comparator offset adjustment signal output DVD/CD phase control signal (positive polarity) DVD/CD phase control signal (negative polarity) DVD/CD phase control signal (positive polarity) DVD/CD phase control signal (negative polarity) Data PLL low-pass filter inversion input Data PLL low-pass filter output Reference power supply for data PLL system only VCO reference VCO self-adjusting filter output Power supply for 3.3V PLL system only Data slice 6-bit DAC output (RFOn input enabled at differential input) Test terminal Test mode terminal CD RF signal input (RFOp input enabled at differential input) DVD RF signal input (RFOp input enabled at differential input) Power supply for 3.3V analog system only RFRP center voltage output (zero cross import) RFRP zero cross signal input Tracking error signal input (zero cross import) Active wide PLL control signal input Ground for 3.3V analog system only Focus error signal input Tracking error signal input RF level or sub beam signal add input RFRP signal input Ground for 3.3V analog system only Test terminal 89 – 3V system 3V system 3V system 3V system 3V system – 3V system 3V system 3V system Analog output terminal Analog output terminal Analog output terminal 3V system Analog input terminal – 3V system Analog output terminal 3V system Analog output terminal 3V system Analog output terminal 3V system Analog output terminal 3V system Analog output terminal 3V system 3V system 3V system Analog input terminal Analog output terminal 3V system 3V system – 3V system Analog input terminal Analog input terminal 3V system 3V system 3V system OPEN Connected to VDD3 Analog input terminal 3V system Analog input terminal – 3V system OPEN 3V system 3V system Analog input terminal Analog input terminal 3V system – 3V system 3V system 3V system 3V system – 3V system Analog input terminal Connected to GND Connected to GND OPEN OPEN Analog output terminal Analog input terminal Analog input terminal Analog input terminal Analog input terminal Connected to VREF 27DV-S100 27DV-CS10 Pin No. Terminal Name In/Output 156 EXTAD Input 157 VREF – 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 FOO TRO AVDD AWCTL FMO DMO TEBC FEBC DPDC EQBC ANMON /DFCT VRCK VSS3 SCD SCL SCB FGIN Output Output – Output Output Output Output Output Output Output Output Output Output – Output Output Output Input 176 ASLCP Output Operation function General-purpose external ADC input Reference power supply for analog system only: 1.65V Focus EQ output Tracking EQ output Power supply for 3.3V analog system only Active wide PLL control output Feed EQ output Disc EQ output Tracking balance control signal Focus balance control signal DPD error signal/pit depth adjustment signal RF wide boost adjustment signal General-purpose PWM output Black dot detection signal RF EQ property control clock 3.3V digital ground Head amplifier serial data Head amplifier serial data latch pulse Head amplifier serial data clock Disc FG signal input (with self-bias circuit) Data slice positive pole output 3/5V system Remarks 3V system Analog input terminal 3V system 3V system 3V system – 3V system 3V system 3V system 3V system 3V system 3V system 3V system 3V system 3V system 3V system – 3V system 3V system 3V system 3V system Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Analog output terminal Feedback resistor Analog input terminal Analog output terminal Note) Terminals with "/" at the beginning of their names are active "L" ones. • Block Diagram to Driver, RFamp DAC DAC I/F Servo signal from RFamp ADC DEQ Digital in Analog out 1bit DAC for CD-DA Clock PLL Servo Control Digital Servo Micom BUS RF signal from RFamp Data Slicer PLL Slice level Gen. Syndrome operation ECC SYNC Det. Demodulation DRAM I/F to DRAM to RFamp 90 Micom I/F Output I/F to Micom to DECORDER 27DV-S100 27DV-CS10 IC702 IX3420CE 4M EDO DRAM Terminal Terminal name Function 16-19, 22-26 A0-A8 Address inputs. 14 RAS Row address strobe. 28 UCAS Column address strobe/upper byte control. 29 LCAS Column address strobe/lower byte control. 13 WE Write enable. 27 OE Output enable. 2-5, 7-10 DQ1-DQ16 Data inputs/outputs. 31-34, 36-39 1, 6, 20 VCC +3.3V power supply. 21, 35, 40 VSS 0V ground. 11-12, 15, 30 NC No connection. • Block Diagram OE WE UCAS LCAS RAS RAS clock generator CAS clock generator WE clock generator OE clock generator VCC VSS Data I/O Bus Column decoders Refresh counter Sense amplifiers Y0-Y8 9 A0 A1 A7 A8 Address buffers and predecoders Row decoders X0-X8 I/O Buffer 512 16 Memory array 512 91 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 I/O16 27DV-S100 27DV-CS10 IC1101 PCM1737 AUDIO DAC Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Terminal name LRCK DATA BCK CLKO SCLK DGND VDD TEST1 TEST2 VCCR AGNDR VCOMR VOUTR AGND VCC VOUTL VCOML AGNDL VCCL NA NA RST ZEROL ZEROR MDO MDI MC ML I/O I I I O I – – I I – – – O – – O – – – I I I O O O I I I Operation function LRCK clock input (fs) (1) Audio • Data input (1) Bit clock input for data. (1) System clock buffered output. System clock input. Digital ground. Digital power supply +3.3V Test pin (2) (Open or ground) Test pin (2) (Open or ground) Rch, Analog power supply +5V Analog ground, Rch Rch Analog output amp. • common Rch Analog voltage output. Analog • ground Analog power supply +5V Lch Analog voltage output Lch Analog output amp • common Analog ground, Lch Lch, Analog power supply +5V Not connected. Not connected. Reset Lch, Zero data • flug Rch, Zero data • flug Mode control, data output (3) Mode control, data input (2) Mode clock (2) Mode latch (2) Note: (1) Schmidt trigger input, 5V logic input possible. (2) Schmidt trigger input pull-down resistor. 5V logic input possible. (3) Try state output • Block Diagram BCK LRCK Sirial I/F DATA x8 (x4) Oversampling Dijital Filter + Mulcher Function Controller TEST1 TEST2 RST ML VOUTL CR LPF + Output Amp DAC VCOML Mulcher Level Data-Sigma Modulator Function Control VOUTR CR LPF + Output Amp DAC MC VCOMR MDI MDO NA System Clock NA VCCR AGNDR VCCL AGNDL VCC VDD DGND ZEROR 92 AGND Power Supply. Zero detection ZEROL Clock Manager CLKO SCLK 27DV-S100 27DV-CS10 IC7701 BA5984FP Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Terminal name LD-FWD SL_IN(+) SL_IN(-) SLOUT SP_IN(+) SP_IN(-) SP_OUT VCC LD(-) LD(+) SPIN(-) SPIN(+) SL(-) SL(+) MOTOR DRIVER Operation function Pin No. Loading driver FWD input terminal 15 CH1 Former stage amplifier nonreverse input terminal 16 CH1 Former stage amplifier reverse input terminal 17 CH1 Former stage amplifier output terminal 18 CH2 Former stage amplifier nonreverse input terminal 19 CH2 Former stage amplifier reverse input terminal 20 CH2 Former stage amplifier output terminal 21 Power terminal 22 Loading driver Negative output 23 Loading driver Positive output 24 Driver CH2 Negative output 25 Driver CH2 Positive output 26 Driver CH1 Negative output 27 Driver CH1 Positive output 28 Terminal name V04(+) V04(-) V03(+) V03(-) GND BIAS MUTE FO_OUT FO_IN(-) FO_IN(+) TR_OUT TR_IN(-) TR_IN(+) REV Operation function Driver CH4 Negative output Driver CH4 Positive output Driver CH3 Negative output Driver CH3 Positive output Ground terminal Bias input terminal Mute control terminal CH3 Former stage amplifier output terminal CH3 Former stage amplifier reverse input terminal CH3 Former stage amplifier nonreverse input terminal CH4 Former stage amplifier output terminal CH4 Former stage amplifier reverse input terminal CH4 Former stage amplifier nonreverse input terminal Loading driver REV input terminal Note 1: Positive and negative output the driver have polarity with respect to input. (An example: 4 pin terminal voltage ‘HIGH’: 14 pin terminal voltage ‘HIGH’) • Block Diagram 26 25 24 23 22 21 20 REV OUTF FWD OUTR 16K 10K 10K 10K + 16K - 15 10K 10K 10K 10K + Level Shift - + - 10K 16 + + 17 + + + 10K Loading Driver 18 10K MUTE 10K 19 + 27 + 28 + Level Shift Level - Shift + 16K 10K + - Level - Shift + 16K 2 3 4 5 6 7 8 93 10 11 12 + + 9 + 10K 10K 1 + + + VCC 10K 10K 10K 10K 10K 13 10K 14 27DV-S100 27DV-CS10 BLOCK DIAGRAM OF TV SECTION H G F E D C B A 1 2 3 94 4 5 6 7 8 9 10 11 95 12 27DV-S100 27DV-CS10 BLOCK DIAGRAM OF VCR SECTION Ë OVERALL BLOCK DIAGRAM H G F E D C B A 1 2 3 96 4 5 6 7 8 9 10 11 97 12 27DV-S100 27DV-CS10 BLOCK DIAGRAM OF VCR SECTION Ë SERVO PROCESS BLOCK DIAGRAM H G F E D C B A 1 2 3 98 4 5 6 7 8 9 10 11 99 12 27DV-S100 27DV-CS10 BLOCK DIAGRAM OF VCR SECTION Ë SYSTEM CONTROL BLOCK DIAGRAM H G F E D C B A 1 2 3 4 100 5 6 27DV-S100 27DV-CS10 BLOCK DIAGRAM OF VCR SECTION Ë SAFETY DEVICE BLOCK DIAGRAM H G F E D C B A 1 2 3 4 101 5 6 27DV-S100 27DV-CS10 BLOCK DIAGRAM OF VCR SECTION Ë VIDEO SIGNAL FLOW AND LINEAR AUDIO FLOW BLOCK DIAGRAM H G F E D C B A 1 2 3 102 4 5 6 7 8 9 10 11 103 12 27DV-S100 27DV-CS10 BLOCK DIAGRAM OF VCR SECTION Ë Hi-Fi AUDIO BLOCK DIAGRAM H G F E D C B A 1 2 3 104 4 5 6 7 8 9 10 11 105 12 27DV-S100 27DV-CS10 BLOCK DIAGRAM OF DVD SECTION H G F E D C B A 1 2 3 106 4 5 6 7 8 9 10 11 107 12 27DV-S100 27DV-CS10 OVERALL SCHEMATIC DIAGRAM H G F E D C B A 1 2 3 108 4 5 6 7 8 9 10 11 109 12 27DV-S100 27DV-CS10 DESCRIPTION OF SECTION SCHEMATIC DIAGRAM NOTES: WAVEFORM MEASUREMENT CONDITIONS: 1. The unit of resistance "ohm" is omitted (K=1000 ohms, M =1 Meg ohm). 2. All resistors are 1/10 watt, unless otherwise noted. 3. All capacitors are 50V, unless otherwise noted. 4. All capacitors are µF, unless otherwise noted. (P: µµF) 5. (G) indicates ±2% tolerance may be used. 1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. indicates waveform check points (See chart, 2. waveforms are measured from point indicated to chassis ground.) VOLTAGE MEASUREMENT CONDITIONS: 1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated. 2. All voltages measured with 1000µV B&W or Color signal. å AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS. ' MARK= X-RAY RELATED PARTS. DRGANNES MARQUES åET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE ' : PIECS RELATIVE AUX RAYONS X. This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice. WAVEFORMS 1 1.9Vp-p 2 Horiz. Rate 7 0.6Vp-p 135Vp-p Horiz. Rate o 2.5Vp-p Horiz. Rate 3 300mVp-p Horiz. Rate 8 Horiz. Rate e 1.9Vp-p 0.8Vp-p Horiz. Rate 9 Horiz. Rate r 140Vp-p Horiz. Rate 4.0Vp-p t 50.9Vp-p 0 3.4Vp-p Horiz. Rate y Vert. Rate a 0.98Vp-p 5 280mVp-p Horiz. Rate Horiz. Rate Horiz. Rate p 1210Vp-p 4 1.8Vp-p Vert. Rate 327Vp-p Vert. Rate 110 6 Horiz. Rate q 3.6Vp-p Horiz. Rate w Horiz. Rate u 727mVp-p Horiz. Rate 0.96Vp-p 127Vp-p Horiz. Rate i 180Vp-p Horiz. Rate 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: CRT Unit H G F E D C B A 1 2 3 4 111 5 6 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: TERMINAL-1 Unit (TV Section) H G F E D C B A 1 2 3 112 4 5 6 7 8 9 10 11 113 12 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: TERMINAL-2 Unit (TV Section) H G F E D C B A 1 2 3 114 4 5 6 7 8 9 10 11 115 12 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: TERMINAL-SUB Unit H G F E D C B A 1 2 3 4 116 5 6 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: FRONT AV Unit H G F E D C B A 1 2 3 4 117 5 6 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: DEFLECTION Unit (TV Section) H G F E D C B A 1 2 3 118 4 5 6 7 8 9 10 11 119 12 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: TV POWER Unit (TV Section) H G F E D C B A 1 2 3 120 4 5 6 7 8 9 10 11 121 12 27DV-S100 27DV-CS10 MODEL 27DV-S100 SCHEMATIC DIAGRAM: MAIN-1 Unit (VCR Section) H G F E D C B A 1 2 3 122 4 5 6 7 8 9 10 11 123 12 27DV-S100 27DV-CS10 MODEL 27DV-S100 SCHEMATIC DIAGRAM: MAIN-2 Unit (VCR Section) H G F E D C B A 1 2 3 124 4 5 6 7 8 9 10 11 125 12 27DV-S100 27DV-CS10 MODEL 27DV-S100 SCHEMATIC DIAGRAM: MAIN-3 Unit (VCR Section) H G F E D C B A 1 2 3 126 4 5 6 7 8 9 10 11 127 12 27DV-S100 27DV-CS10 MODEL 27DV-CS10 SCHEMATIC DIAGRAM: MAIN-1 Unit (VCR Section) H G F E D C B A 1 2 3 128 4 5 6 7 8 9 10 11 129 12 27DV-S100 27DV-CS10 MODEL 27DV-CS10 SCHEMATIC DIAGRAM: MAIN-2 Unit (VCR Section) H G F E D C B A 1 2 3 130 4 5 6 7 8 9 10 11 131 12 27DV-S100 27DV-CS10 MODEL 27DV-CS10 SCHEMATIC DIAGRAM: MAIN-3 Unit (VCR Section) H G F E D C B A 1 2 3 132 4 5 6 7 8 9 10 11 133 12 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: DVD/VCR POWER Unit (VCR Section) H G F E D C B A 1 2 3 134 4 5 6 7 8 9 10 11 135 12 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: DVD MAIN-1 Unit (DVD Section) H G F E D C B A 1 2 3 136 4 5 6 7 8 9 10 11 137 12 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: DVD MAIN-2 Unit (DVD Section) H G F E D C B A 1 2 3 138 4 5 6 7 8 9 10 11 139 12 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: DVD SUB Unit (DVD Section) H G F E D C B A 1 2 3 140 4 5 6 7 8 9 10 11 141 12 27DV-S100 27DV-CS10 SCHEMATIC DIAGRAM: CONTROL Unit H (VCR Section) G F E (DVD Section) D C B A 1 2 3 4 142 5 6 27DV-S100 27DV-CS10 PRINTED WIRING BOARD ASSEMBLIES H G F E CRT Unit (Wiring Side) D C B TERMINAL SUB Unit (Wiring Side) A 1 2 3 4 143 5 6 27DV-S100 27DV-CS10 H G F E D C B MAIN Unit (Wiring Side) A 1 2 3 4 144 5 6 27DV-S100 27DV-CS10 H G F E D C B MAIN Unit (Chip Parts Side) A 1 2 3 4 145 5 6 27DV-S100 27DV-CS10 H G F E D C B A TERMINAL Unit (Wiring Side) 1 2 3 4 146 5 6 27DV-S100 27DV-CS10 H G F E D C B A TERMINAL Unit (Chip Parts Side) 1 2 3 4 147 5 6 27DV-S100 27DV-CS10 H G F E D C B TV POWER Unit (Wiring Side) A 1 2 3 4 148 5 6 27DV-S100 27DV-CS10 H G F E D C B A DEFLECTION Unit (Wiring Side) 1 2 3 4 149 5 6 27DV-S100 27DV-CS10 H G F E D C B A DVD/VCR POWER Unit (Wiring Side) 1 2 3 4 150 5 6 27DV-S100 27DV-CS10 H G VCR CONTROL Unit (Wiring Side) F E D DVD CONTROL Unit (Wiring Side) C B A FRONT AV Unit (Wiring Side) 1 2 3 4 151 5 6 27DV-S100 27DV-CS10 H G F E D C B A DVD MAIN Unit (A Side) 1 2 3 4 152 5 6 27DV-S100 27DV-CS10 H G F E D C B A DVD MAIN Unit (B Side) 1 2 3 4 153 5 6 27DV-S100 27DV-CS10 H G F DVD SUB Unit (Wiring Side) E D C B DVD SUB Unit (Chip Parts Side) A 1 2 3 4 154 5 6 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description PARTS LIST Code Ref. No. Part No. ★ Description Code LISTE DES PIECES PARTS REPLACEMENT CHANGE DES PIECES Replacement parts which have these special safety characteristics identified in this manual: electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards. Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep éler élee par la marque å et sont hachur élees dans les listes de pi‘eces et dans les diagrammes sch élematiques. La substitution d’une pi`ece de rechange par une autre qui ne pr éLesente pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece recommand élee parl`usine et dans ce manuel de service, peut provoquer une éLelectrocution, un incendie ou toutautre sinistre. "HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION in USA: "COMMENT COMMANDER LES PIECES DE RECHANGE" Pour que votre commande soit rapidement et correctement remplie, veuillez fournir les renseignements suivants. 1. NUMERO DU MODELE 3. NO. DE PIECE Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP in CANADA: ★ MARQUE: SECTION LIVRAISON DES PIECES DERECHANGE ' MARK : X-RAY RELATED PARTS ' MARQUE: PIECES RELATIVE AUX RAYONS X Part No. ★ Description Code VB68LUW696X~S RCiLH0259PEZZ LHLDW0003PEKZ LHLDW1075PEKZ PMAGF3040CEN1 PMAGG3006CEZZ PSPAG0003PEZZ QCNW-5298CEZZ QEARC2913PEZZ RCiLG0056PEZZ RCORF0031CEZZ J R R R J J J J R R J Picture Tube Deflection Yoke ADG Coil Holder, x4 Holder Purity Magnet Magnet Spacer, x3 Connecting Cord (PU) Grounding Strap Degaussing Coil Ferrite Core Ref. No. Part No. ★ Description Code DUNTKA603WEV5(27DV-S100) DUNTKA603WEV6(27DV-CS10) MAIN Unit PICTURE TUBE å Contact SHARP Electronics of Canada Limited Phone (416) 890-2100 ★ MARK : SPARE PARTS-DELIVERY SECTION Ref. No. 'å å 2. NO. DE REF 4. DESCRIPTION INTEGRATED CIRCUITS CV BN AB AC AN AC AD AE AK AS AM IC2001 IC2002 IC2003 IC2004 RH-iX1731GEZZQ VHiPST600H/-1 VHiBR24C04F-1 VHiBR24C08F-1 IC2005 VHiPST994C/-1 IC2201 VHiHA8317NF-1 or VHiHA8317F/-1 IC6651 VHiAN3651FB-1 IC7006 VHiLB11880+-1 or VHiLB1988//-1 R J J J MN101D06GSJ IC-ST600H-2 BR24C04F-WE2 BR24C08F-E2 (27DV-S100) J PST994C J HA118317NF AZ AE AG AF J AN3651FBP J LB11880 AU AL AD AZ TRANSISTORS Q2001 Q2002 Q2003 Q2004 Q2201 Q3302 Q3306 Q5501 Q5502 Q6602 Q6603 Q6604 Q6605 Q6606 Q6607 Q6608 Q6609 Q6651 Q6652 Q6653 Q6654 Q7001 Q7002 Q7010 Q7011 Q7020 PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM) DUNTKA603WEV5 DUNTKA603WEV6 DUNTKA637WEV1 DUNTKA638WEV1 DUNTKA639WEV1 DUNTKA640WEV1 DUNTKA642WEV1 DUNTKA643WEV1 DUNTKA669WEV1 DUNTKA680WEV1 DUNTKA686WEV1 DUNTK6054TE6H DUNTK6081TEV1 B3DVK03DVD – – – – – – – – – – – – – – Main Unit(27DV-S100) Main Unit(27DV-CS10) DVD/VCR Power Unit Deflection Unit TV Power Unit Terminal Unit Control(DVD) Unit Control(VCR) Unit Front AV Unit Terminal Sub Unit CRT Unit DVD Main Unit DVD Sub Unit DVD Unit — — — — — — — — — — — — — — 155 VS2SC1623L51E VS2SA1271-Y-1 VS2SA1271-Y-1 VS2SC1623L51E VS2SC1623L51E VS2SD1306-E-1 VS2SA812-M/1E VS2SC1623L51E VS2SC1623L51E VS2SC3203Y/-1 VS2SC1623L51E VSKRC104S//-1 VS2SC2712Y/-1 VS2SC2712Y/-1 VSKRA102S//-1 VSKRC104S//-1 VSKRC104S//-1 VS2SD1306-E-1 VS2SD1306-E-1 VSKRA104S//-1 VSKRC104S//-1 RH-PX0233GEZZ RH-PX0233GEZZ VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E J J J J J J J J J J J J J J J J J J J J J J J J J J 2SC1635L5 2SA1271-Y 2SA1271-Y 2SC1635L5 2SC1635L5 2SD1306-E 2SA812-M 2SC1635L5 2SC1635L5 2SC3023Y 2SC1635L5 KRC104S 2SC2712Y 2SC2712Y KRA102S KRC104S KRC104S 2SD1306-E 2SD1306-E KRC104S KRC104S PT493FL2, Strat Sensor PT493FL2, End Sensor 2SC1635L5 2SC1635L5 2SC1635L5 AB AB AB AB AB AC AC AB AB AB AB AA AB AB AA AA AA AC AC AA AA AD AD AB AB AB 27DV-S100 27DV-CS10 Ref. No. ★ Part No. Description Code DUNTKA603WEV5(27DV-S100) DUNTKA603WEV6(27DV-CS10) MAIN Unit (Continued) Q8301 Q8302 Q8303 Q8304 Q8305 Q9101 Q9102 Q9103 Q9104 Q9111 Q9112 VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SA1271-Y-1 VSKRC102S//-1 VS2SA812-M/1E VSKRC102S//-1 VS2SB1443TV1E VSKRC102S//-1 D2001 D2002 D2003 D2010 D2011 D2012 D6650 D6691 D7001 D7006 D7007 D7008 D7009 D7015 D7016 D8312 D8313 D8314 D8315 VHD1SS119//-1 VHD1SS119//-1 RH-EX0631GEZZ VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-EX0631GEZZ RH-PX0270GEZZ RH-PX0252GEZZ RH-PX0252GEZZ RH-PX0311GEZZ RH-PX0311GEZZ VHD1SS119//-1 VHD1SS119//-1 RH-PX0348CEZZ RH-PX0348CEZZ RH-PX0348CEZZ RH-PX0423CEZZ J J J J J J J J J J J 2SC1635L5 2SC1635L5 2SC1635L5 2SC1635L5 2SC1635L5 2SA1271-Y KRC102S 2SA812-M KRC102S 2SB1443TV KRC102S C2204 C2205 C2206 C2207 C2208 C2209 C2210 C2211 C2212 C2213 C2214 C2215 C2216 C2217 C2218 C2219 C2220 C2221 C2223 C2224 C2226 C2227 C2228 C3301 C3302 C3303 C3304 C3305 C3306 C3307 C3308 C3309 C3310 C3311 C3313 C3314 C3316 C3319 C3320 C3327 C3329 C5501 C5502 C5503 C5504 C5505 C5506 C5507 C5508 C5509 C5512 C5513 C5514 C5515 C5516 C5517 C5518 C5521 C5523 C5524 C6601 C6602 C6603 C6604 C6605 C6606 C6607 C6608 C6609 C6610 C6611 C6613 C6614 C6615 C6617 C6618 AB AB AB AB AB AB AA AC AA AE AA DIODES J J J J J J J J J J J J J J J J J J J Diode Diode Zener Diode Diode Diode Diode Diode Zener Diode Casstte LED SUP Reel Sensor TU Reel Sensor CAM SW A CAM SW B Diode Diode LED, Record LED, Program LED, Tamper Proof LED, Power On AB AB AA AB AB AB AB AA AC AF AF AD AD AB AB AB AB AB AD PACKAGED CIRCUITS X5501 RCRSB0204GEZZ J Crystal X7001 RCRSB0205GEZZ J Crystal AG AM COILS L2201 L3301 L3302 L3303 L5503 L6602 L6605 L6668 VP-XF820K0000 VP-MK101K0000 VP-ZK471K0000 VP-ZK561K0000 VP-XF120K0000 VP-DF221K0000 VPADK153J0000 VP-MK101K0000 J J J J J J J J Peaking 82µH Peaking 100µH Peaking 470µH Peaking 560µH Peaking 12µH Peaking 220µH Peaking 15mH Peaking 100µH AB AB AB AB AB AB AC AB TRANSFORMER T6601 RTRNH0098GEZZ J Osc. Transformer AE CAPACITORS [EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film] C2001 VCKYCY1HF103Z J 0.01 50V Ceramic C2002 VCKYCY1HB222K J 2200p 50V Ceramic C2003 VCEA2A0JW108M J 1000 6.3V EL. C2004 VCKYCY1CF104Z J 0.1 16V Ceramic C2005 VCKYCY1HF103Z J 0.01 50V Ceramic C2006 VCEA9M0JW227M J 220 6.3V EL. C2008 VCKYCY1EB223K J 0.022 25V Ceramic C2012 VCKYCY0JF105Z J 1.0 6.3V Ceramic C2021 VCKYCY1EB103K J 0.01 25V Ceramic C2022 VCKYCY1HB222K J 2200p 50V Ceramic C2039 VCKYCY1HF103Z J 0.01 50V Ceramic C2040 VCKYCY1HF103Z J 0.01 50V Ceramic C2051 VCKYCY1CF104Z J 0.1 16V Ceramic C2052 VCCCCY1HH330J J 33p 50V Ceramic C2053 VCCCCY1HH330J J 33p 50V Ceramic C2067 VCEA9M0JW476M J 47 6.3V EL. C2201 VCEA9M0JW107M J 100 6.3V EL. C2202 VCKYCY1CF104Z J 0.1 16V Ceramic C2203 VCCCCY1HH151J J 150p 50V Ceramic Ref. No. AA AA AB AA AA AB AA AB AA AA AA AA AA AA AA AB AB AA AA 156 Part No. VCKYCY1CF104Z VCCCCY1HH470J VCKYCY1CF104Z VCKYCY1CF104Z VCEA9A1CW106M VCKYCY1CF104Z VCKYCY1CF104Z VCEA9M1HW335M VCEA9A1CW106M VCEA9M1HW225M VCKYCY1CF104Z VCKYCY0JF105Z VCKYCY1CF104Z VCEA9M0JW107M VCKYCY1CF104Z VCKYCY0JF105Z VCKYCY1CF104Z VCEA9M1CW106M VCKYCY1CF104Z VCEA0A0JW477M VCEA9M0JW107M VCKYCY1CF104Z VCEA9M0JW107M VCEAKM0JW107M VCKYCY1CF104Z VCKYCY1HF223Z VCKYCY1HF223Z VCKYCY1HF223Z VCKYCY1HF223Z VCKYCY1HF223Z VCKYCY1HF223Z VCKYCY1HF223Z VCKYCY1HF223Z VCKYCY1HF103Z VCKYCY1CB104K VCKYCY1HF223Z VCKYCY1HF103Z VCCCCY1HH100D VCCCCY1HH100D VCKYCY1CF104Z VCKYCY1HF103Z VCEA9A0JW107M VCKYCY1CF104Z VCKYCY1HB472K VCEA9M1HW225M VCKYCY1EB223K VCEA9M1HW474M VCKYCY1CF104Z VCEA9M1HW475M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB331K VCKYCY1HF103Z VCEAKM1HW335M VCKYCY1HF333Z VCCCCY1HH5R0C VCKYCY1HF103Z VCKYCY1HF103Z VCEAKM0JW107M VCKYCY1EB103K VCEAKM1CW106M VCKYCY1HB821K VCEA9M1CW106M VCEA9M1HW475M VCEAKM1HW475M VCEA9M1CW226M VCEA9A1HW475M VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1EB183K VCKYCY1HB222K VCKYCY1CF104Z VCEA9M1CW476M VCKYCY1EB103K ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 0.1 47p 0.1 0.1 10 0.1 0.1 3.3 10 2.2 0.1 1.0 0.1 100 0.1 1.0 0.1 10 0.1 470 100 0.1 100 100 0.1 0.022 0.022 0.022 0.022 0.022 0.022 0.022 0.022 0.01 0.1 0.022 0.01 10p 10p 0.1 0.01 100 0.1 4700p 2.2 0.022 0.47 0.1 4.7 0.01 0.01 0.01 0.01 330p 0.01 3.3 0.033 5.0p 0.01 0.01 100 0.01 10 820p 10 4.7 4.7 22 4.7 0.1 0.1 0.018 2200p 0.1 47 0.01 16V 50V 16V 16V 16V 16V 16V 50V 16V 50V 16V 6.3V 16V 6.3V 16V 6.3V 16V 16V 16V 6.3V 6.3V 16V 6.3V 6.3V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 50V 50V 50V 50V 16V 50V 6.3V 16V 50V 50V 25V 50V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 6.3V 25V 16V 50V 16V 50V 50V 16V 50V 16V 16V 25V 50V 16V 16V 25V Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic EL. EL. EL. Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic EL. Ceramic EL. EL. Ceramic EL. EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic EL. Ceramic EL. Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic EL. Ceramic EL. Ceramic EL. EL. EL. EL. EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Code AA AA AA AA AB AA AA AB AB AB AA AB AA AB AA AB AA AB AA AC AB AA AB AB AA AB AB AB AB AB AB AB AB AA AB AB AA AA AA AA AA AB AA AA AB AA AB AA AB AA AA AA AA AA AA AB AA AA AA AA AB AA AB AA AB AB AC AB AB AA AA AA AA AA AB AA 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code DUNTKA603WEV5(27DV-S100) DUNTKA603WEV6(27DV-CS10) MAIN Unit (Continued) C6619 C6620 C6621 C6622 C6624 C6630 C6650 C6651 C6652 C6653 C6654 C6655 C6656 C6657 C6660 C6661 C6662 C6663 C6664 C6665 C6666 C6667 C6668 C6669 C6670 C6671 C6672 C6673 C6674 C6675 C6676 C6677 C6678 C6679 C6680 C6681 C6682 C6683 C6684 C6685 C6686 C6687 C7001 C7004 C7005 C7006 C7007 C7008 C7011 C7012 C7013 C7014 C7015 C7017 C7018 C7019 C7020 C7022 C7023 C7025 C7029 C7030 C7036 C7037 C7038 C7039 C7043 C7052 C7053 C7054 C7055 C7056 VCKYCY1EB103K VCEA9M1CW106M VCQPYA2AA562J VCKYCY1HB222K VCKYCY1CF104Z VCKYCY1CF104Z VCKYCY1CB104K VCEA9M1HW475M VCEAKM0JW336M VCEA9M1CW106M VCEAKM1CW106M VCEA9M1CW106M VCKYCY1CB104K VCKYCY1EB153K VCKYCY1HF103Z VCEA9M1HW475M VCEAKM0JW336M VCEAKM1CW106M VCEAKM1CW106M VCEAKM1CW106M VCCCCY1HH101J VCKYCY1EB153K VCEAKM0JW107M VCKYCY1HF103Z VCEAKM0JW107M VCEA9M1CW107M VCKYCY0JF105Z VCEA9M0JW226M VCKYCY1CF224Z VCKYCY1CF104Z VCKYCY1CB104K VCEA9M1CW106M VCKYCY1HF103Z VCKYCY1CF224Z VCKYCY0JF105Z VCKYCY1HF103Z VCKYCY0JF105Z VCEAKM1CW106M VCCCCY1HH560J VCCCCY1HH560J VCKYCY1CB473K VCKYCY1CB473K VCKYCY1EB103K VCKYCY0JF105Z VCKYCY1EB103K VCKYCY1EB103K VCCCCY1HH150J VCCCCY1HH150J VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1CF104Z VCEA9M1CW226M VCKYCY1HB221K VCKYCY1CF104Z VCKYCY1EB103K VCKYCY1CB273K VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB102K VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB102K VCKYCY1HB102K VCKYCY0JF105Z VCEA0A1VW107M VCCCCY1HH680J VCKYCY1EB103K VCKYCY1CB473K VCKYCY1HF473Z J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.01 10 5600p 2200p 0.1 0.1 0.1 4.7 33 10 10 10 0.1 0.015 0.01 4.7 33 10 10 10 100p 0.015 100 0.01 100 100 1.0 22 0.22 0.1 0.1 10 0.01 0.22 1.0 0.01 1.0 10 56p 56p 0.047 0.047 0.01 1.0 0.01 0.01 15p 15p 1000p 1000p 1000p 0.1 22 220p 0.1 0.01 0.027 0.01 0.01 1000p 0.01 0.01 0.01 0.01 1000p 1000p 1.0 100 68p 0.01 0.047 0.047 25V 16V 100V 50V 16V 16V 16V 50V 6.3V 16V 16V 16V 16V 25V 50V 50V 6.3V 16V 16V 16V 50V 25V 6.3V 50V 6.3V 16V 6.3V 6.3V 16V 16V 16V 16V 50V 16V 6.3V 50V 6.3V 16V 50V 50V 16V 16V 25V 6.3V 25V 25V 50V 50V 50V 50V 50V 16V 16V 50V 16V 25V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 6.3V 35V 50V 25V 16V 50V Ceramic EL. M-Poly Ceramic Ceramic Ceramic Ceramic EL. EL. EL. EL. EL. Ceramic Ceramic Ceramic EL. EL. EL. EL. EL. Ceramic Ceramic EL. Ceramic EL. EL. Ceramic EL. Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ref. No. C7058 C7059 C7060 C7062 C7063 C7064 C7070 C7072 C7073 C7074 C7075 C7077 C7080 C7083 C7084 C7085 C7086 C7087 C7089 C7090 C7091 C7092 C7093 C7094 C7095 C7097 C7098 C9101 C9102 C9103 C9104 C9111 AA AB AC AA AA AA AB AB AB AB AB AB AB AA AA AB AB AB AB AB AA AA AB AA AB AB AB AB AA AA AB AB AA AA AB AA AB AB AA AA AA AA AA AB AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AB AC AA AA AA AA ★ Part No. VCKYCY1HF103Z VCEA9M1CW226M VCEA9M0JW107M VCEA9M1HW225M VCEA9M0JW476M VCKYCY1HF103Z VCKYCY1HF103Z VCCCCY1HH151J VCE9EM1HW105M VCKYCY1CF104Z VCEA9M0JW227M VCCCCY1HH471J VCKYCY1HF103Z VCKYCY0JF105Z VCKYCY1HB102K VCEA9M0JW476M VCKYCY1CF334Z VCFYFA1HA474J VCKYCY1EB103K VCKYCY1HB392K VCKYCY1HB392K VCEA9M1CW107M RC-EZ0459CEZZ VCKYCY1EB223K VCKYCY1EB223K VCKYCY1CF104Z VCKYCY1EB223K VCEA9M1CW226M VCEA9M0JW476M VCEA9M1CW226M VCEA9M0JW476M VCEA9M0JW476M J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 0.01 22 100 2.2 47 0.01 0.01 150p 1.0 0.1 220 470p 0.01 1.0 1000p 47 0.33 0.47 0.01 3900p 3900p 100 10 0.022 0.022 0.1 0.022 22 47 22 47 47 50V 16V 6.3V 50V 6.3V 50V 50V 50V 50V 16V 6.3V 50V 50V 6.3V 50V 6.3V 16V 50V 25V 50V 50V 16V 16V 25V 25V 16V 25V 16V 6.3V 16V 6.3V 6.3V Ceramic EL. EL. EL. EL. Ceramic Ceramic Ceramic EL. (N.P) Ceramic EL. Ceramic Ceramic Ceramic Ceramic EL. Ceramic Mylar Ceramic Ceramic Ceramic EL. EL. Ceramic Ceramic Ceramic Ceramic EL. EL. EL. EL. EL. Code AA AB AB AB AB AA AA AA AB AA AB AA AA AB AA AB AA AC AA AA AA AB AE AA AA AA AA AB AB AB AB AB RESISTORS R2001 R2002 R2003 R2004 R2005 R2006 R2008 R2009 R2010 R2012 R2014 R2015 R2016 R2018 R2020 R2021 R2022 R2023 R2024 R2025 R2026 R2027 R2028 R2029 R2030 R2031 R2032 R2033 R2034 R2035 R2036 R2037 R2038 R2039 R2040 R2041 R2042 R2043 R2044 157 [M-Ox.··· Metal Oxide, M-Film··· Metal Film] VRN-MD2AL563J J 56k 1/10W M-Film VRN-MD2AL101J J 100 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL103J J 10k 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL101J J 100 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRD-RA2BE102J J 1.0k 1/8W Carbon VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL472J J 4.7k 1/10W M-Film VRN-MD2AL683J J 68k 1/10W M-Film VRN-MD2AL564J J 560k 1/10W M-Film VRD-RA2BE102J J 1.0k 1/8W Carbon VRN-MD2AL222J J 2.2k 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL101J J 100 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL473J J 47k 1/10W M-Film VRN-MD2AL331J J 330 1/10W M-Film VRN-MD2AL331J J 330 1/10W M-Film VRN-MD2AL153J J 15k 1/10W M-Film VRN-MD2AL153J J 15k 1/10W M-Film VRN-MD2AL681J J 680 1/10W M-Film VRN-MD2AL103J J 10k 1/10W M-Film VRN-MD2AL472J J 4.7k 1/10W M-Film VRN-MD2AL472J J 4.7k 1/10W M-Film VRN-MD2AL472J J 4.7k 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL000J J 0 1/10W M-Film VRN-MD2AL473J J 47k 1/10W M-Film (27DV-CS10) VRN-MD2AL392J J 3.9k 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL102J J 1.0k 1/10W M-Film VRN-MD2AL472J J 4.7k 1/10W M-Film VRN-MD2AL104J J 100k 1/10W M-Film VRN-MD2AL222J J 2.2k 1/10W M-Film VRN-MD2AL103J J 10k 1/10W M-Film AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code DUNTKA603WEV5(27DV-S100) DUNTKA603WEV6(27DV-CS10) MAIN Unit (Continued) R2045 VRN-MD2AL473J R2046 R2051 R2052 R2053 R2054 R2055 R2056 R2057 R2059 R2061 R2063 R2064 R2065 R2067 R2075 R2077 R2079 R2080 R2087 R2088 R2089 R2090 R2091 R2092 R2201 R2202 R2203 R2206 R2207 R2208 R2209 R2210 R2211 R2212 R2213 R2214 R3301 R3302 R3313 R3315 R3330 R3331 R5501 R5502 R5503 R5506 R5507 R5508 R5511 R5512 R5520 R5521 R6601 R6602 R6603 R6604 R6605 R6606 R6607 R6608 R6611 R6612 R6617 R6619 R6620 R6621 R6623 R6627 R6630 VRD-RA2BE4R7J VRN-MD2AL562J VRN-MD2AL562J VRN-MD2AL331J VRN-MD2AL331J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL103J VRN-MD2AL183J VRN-MD2AL102J VRN-MD2AL183J VRN-MD2AL103J VRD-RA2BE470J VRN-MD2AL000J VRN-MD2AL101J VRN-MD2AL102J VRN-MD2AL000J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL681J VRN-MD2AL102J VRN-MD2AL122J VRN-MD2AL682J VRN-MD2AL682J VRN-MD2AL182J VRN-MD2AL682J VRN-MD2AL000J VRN-MD2AL101J VRN-MD2AL101J VRN-MD2AL332J VRN-MD2AL332J VRN-MD2AL272J VRN-MD2AL471J VRN-MD2AL000J VRN-MD2AL000J VRD-RA2BE473J VRN-MD2AL681J VRD-RA2BE332J VRN-MD2AL152J VRN-MD2AL222J VRN-MD2AL102J VRN-MD2AL681J VRN-MD2AL273J VRN-MD2AL101J VRN-MD2AL223J VRN-MD2AL223J VRN-MD2AL471J VRN-MD2AL272J VRN-MD2AL272J VRN-MD2AL154J VRN-MD2AL473J VRN-MD2AL822J VRN-MD2AL274J VRN-MD2AL221J VRN-MD2AL473J VRN-MD2AL153J VRN-MD2AL273J VRN-MD2AL561J VRN-MD2AL472J VRN-MD2AL153J VRN-MD2AL823J VRN-MD2AL103J VRD-RA2BE470J VRN-MD2AL153J VRD-RA2EE4R7J VRN-MD2AL223J VRD-RA2BE332J VRN-MD2AL472J J 47k 1/10W (27DV-S100) J 4.7 1/8W J 5.6k 1/10W J 5.6k 1/10W J 330 1/10W J 330 1/10W J 1.0k 1/10W J 1.0k 1/10W J 1.0k 1/10W J 10k 1/10W J 18k 1/10W J 1.0k 1/10W J 18k 1/10W J 10k 1/10W J 47 1/8W J 0 1/10W J 100 1/10W J 1.0k 1/10W J 0 1/10W J 1.0k 1/10W J 1.0k 1/10W J 680 1/10W J 1.0k 1/10W J 1.2k 1/10W J 6.8k 1/10W J 6.8k 1/10W J 1.8k 1/10W J 6.8k 1/10W J 0 1/10W J 100 1/10W J 100 1/10W J 3.3k 1/10W J 3.3k 1/10W J 2.7k 1/10W J 470 1/10W J 0 1/10W J 0 1/10W J 47k 1/8W J 680 1/10W J 3.3k 1/8W J 1.5k 1/10W J 2.2k 1/10W J 1.0k 1/10W J 680 1/10W J 27k 1/10W J 100 1/10W J 22k 1/10W J 22k 1/10W J 470 1/10W J 2.7k 1/10W J 2.7k 1/10W J 150k 1/10W J 47k 1/10W J 8.2k 1/10W J 270k 1/10W J 220 1/10W J 47k 1/10W J 15k 1/10W J 27k 1/10W J 560 1/10W J 4.7k 1/10W J 15k 1/10W J 82k 1/10W J 10k 1/10W J 47 1/8W J 15k 1/10W J 4.7 1/4W J 22k 1/10W J 3.3k 1/8W J 4.7k 1/10W M-Film AA Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film Carbon M-Film Carbon M-Film AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA Ref. No. R6631 R6632 R6653 R6654 R6657 R6658 R6659 R6660 R6663 R6664 R6667 R6668 R6669 R6670 R6671 R6672 R6673 R6674 R6675 R6676 R6677 R6681 R6682 R6683 R6684 R6685 R6686 R6687 R6696 R7001 R7002 R7003 R7004 R7005 R7006 R7007 R7008 R7009 R7010 R7011 R7012 R7014 R7015 R7016 R7017 R7018 R7019 R7020 R7021 R7022 R7023 R7024 R7025 R7026 R7027 R7028 R7029 R7030 R7031 R7032 R7033 R7034 R7035 R7036 R7037 R7038 R7039 R7040 R7041 R7042 R7043 R7044 R7045 R7046 R7047 158 Part No. ★ VRN-MD2AL222J VRN-MD2AL103J VRD-RA2BE473J VRN-MD2AL682J VRN-MD2AL101J VRN-MD2AL223J VRN-MD2AL681J VRD-RA2BE102J VRD-RA2BE473J VRN-MD2AL682J VRN-MD2AL101J VRN-MD2AL223J VRN-MD2AL681J VRN-MD2AL273J VRN-MD2AL103J VRN-MD2AL151J VRN-MD2AL151J VRN-MD2AL473J VRN-MD2AL183J VRN-MD2AL102J VRN-MD2AL473J VRN-MD2AL472J VRN-MD2AL471J VRN-MD2AL471J VRN-MD2AL472J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL000J VRD-RA2BE151J VRN-MD2AL102J VRN-MD2AL000J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL103J VRD-RA2BE473J VRD-RA2BE473J VRD-RA2BE223J VRN-MD2AL332J VRN-MD2AL102J VRD-RA2BE102J VRN-MD2AL331J VRN-MD2AL182J VRN-MD2AL103J VRN-MD2AL102J VRD-RA2BE101J VRN-MD2AL102J VRN-MD2AL331J VRD-RA2BE103J VRN-MD2AL102J VRN-MD2AL101J VRD-RA2EE151J VRN-MD2AL152J VRD-RA2BE154J VRN-MD2AL102J VRN-MD2AL473J VRN-MD2AL223J VRN-MD2AL102J VRN-MD2AL223J VRN-MD2AL563J VRN-MD2AL123J VRN-MD2AL000J VRN-MD2AL104J VRD-RA2BE271J VRN-MD2AL104J VRD-RA2BE271J VRN-MD2AL473J VRD-RA2BE391J VRN-MD2AL473J VRD-RA2BE391J VRD-RA2BE102J VRD-RA2BE102J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 2.2k 10k 47k 6.8k 100 22k 680 1.0k 47k 6.8k 100 22k 680 27k 10k 150 150 47k 18k 1.0k 47k 4.7k 470 470 4.7k 1.0k 1.0k 0 150 1.0k 0 1.0k 1.0k 1.0k 10k 10k 10k 10k 47k 47k 22k 3.3k 1.0k 1.0k 330 1.8k 10k 1.0k 100 1.0k 330 10k 1.0k 100 150 1.5k 150k 1.0k 47k 22k 1.0k 22k 56k 12k 0 100k 270 100k 270 47k 390 47k 390 1.0k 1.0k 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/4W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/8W 1/10W 1/8W 1/10W 1/8W 1/8W 1/8W M-Film M-Film Carbon M-Film M-Film M-Film M-Film Carbon Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon Carbon Carbon M-Film M-Film Carbon M-Film M-Film M-Film M-Film Carbon M-Film M-Film Carbon M-Film M-Film Carbon M-Film Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film Carbon M-Film Carbon M-Film Carbon Carbon Carbon Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. ★ Part No. Description Code DUNTKA603WEV5(27DV-S100) DUNTKA603WEV6(27DV-CS10) MAIN Unit (Continued) R7048 R7050 R7051 R7052 R7053 R7054 R7056 R7057 R7059 R7060 R7061 R7062 R7063 R7064 R7065 R7067 R7068 R7069 R7070 R7071 R7072 R7073 R7074 R7075 R7076 R7077 R7078 R7079 R7080 R7081 R7082 R7083 R7084 R7085 R7086 R7087 R7088 R7089 R7090 R7091 R7092 R7093 R7094 R7095 R7096 R7099 R8301 R8305 R8312 R8313 R8314 R9101 R9102 R9103 R9104 R9105 R9106 R9111 R9112 R9113 VRS-CY1JF1R0J VRN-MD2AL474J VRN-MD2AL123J VRN-MD2AL123J VRD-RA2BE102J VRD-RA2BE102J VRN-MD2AL102J VRD-RA2BE102J VRN-MD2AL000J VRN-MD2AL104J VRN-MD2AL104J VRN-MD2AL103J VRN-MD2AL332J VRN-MD2AL000J VRN-MD2AL152J VRD-RA2BE103J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL333J VRN-MD2AL102J VRN-MD2AL102J VRN-MD2AL102J VRD-RA2BE102J VRN-MD2AL104J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL103J VRN-MD2AL104J VRN-MD2AL392J VRN-MD2AL104J VRN-MD2AL105J VRN-MD2AL564J VRD-RM2HD1R0J VRD-RM2HD1R0J VRN-MD2AL822J VRD-RA2BE472J VRS-CY1JF1R0J VRN-MD2AL473J VRN-MD2AL154J VRN-MD2AL332J VRN-MD2AL105J VRN-MD2AL103J VRN-MD2AL103J VRD-RA2BE471J VRD-RA2BE821J VRD-RA2BE561J VRD-RA2BE561J VRD-RA2BE561J VRD-RA2BE471J VRN-MD2AL103J VRD-RA2BE222J VRD-RA2BE222J VRN-MD2AL103J VRD-RA2BE222J VRN-MD2AL103J VRD-RA2BE471J VRD-RA2BE222J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 1.0 1/16W M-Ox. 470k 1/10W M-Film 12k 1/10W M-Film 12k 1/10W M-Film 1.0k 1/8W Carbon 1.0k 1/8W Carbon 1.0k 1/10W M-Film 1.0k 1/8W Carbon 0 1/10W M-Film 100k 1/10W M-Film 100k 1/10W M-Film 10k 1/10W M-Film 3.3k 1/10W M-Film 0 1/10W M-Film 1.5k 1/10W M-Film 10k 1/8W Carbon 1.0k 1/10W M-Film 1.0k 1/10W M-Film 1.0k 1/10W M-Film 1.0k 1/10W M-Film 1.0k 1/10W M-Film 33k 1/10W M-Film 1.0k 1/10W M-Film 1.0k 1/10W M-Film 1.0k 1/10W M-Film 1.0k 1/8W Carbon 100k 1/10W M-Film 10k 1/10W M-Film 10k 1/10W M-Film 10k 1/10W M-Film 100k 1/10W M-Film 3.9k 1/10W M-Film 100k 1/10W M-Film 1.0M 1/10W M-Film 560k 1/10W M-Film 1.0 1/2W Carbon 1.0 1/2W Carbon 8.2k 1/10W M-Film 4.7k 1/8W Carbon 1.0 1/16W M-Ox. 47k 1/10W M-Film 150k 1/10W M-Film 3.3k 1/10W M-Film 1.0M 1/10W M-Film 10k 1/10W M-Film 10k 1/10W M-Film 470 1/8W Carbon 820 1/8W Carbon 560 1/8W Carbon 560 1/8W Carbon 560 1/8W Carbon 470 1/8W Carbon 10k 1/10W M-Film 2.2k 1/8W Carbon 2.2k 1/8W Carbon 10k 1/10W M-Film 2.2k 1/8W Carbon 10k 1/10W M-Film 470 1/8W Carbon 2.2k 1/8W Carbon P2002 P2202 P3301 P7001 P7005 P7006 P7007 SC3301 SC6601 SC6602 SC6651 SC7001 SC7002 SC7003 RMC2002 W7001 W7002 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA SWITCHES S2002 QSW-P0620CEZZ S7001 QSW-F0042AJZZ J Power J Rec Tip Switch AF AG MISCELLANEOUS PARTS FB2201 FB2202 FB2203 FB7001 FB7002 RBLN-0090GEZZ~ RBLN-0090GEZZ~ RBLN-0090GEZZ~ RBLN-0090GEZZ~ RBLN-0090GEZZ~ R R R R R Ferrtie Bead Ferrtie Bead Ferrtie Bead Ferrtie Bead Ferrtie Bead Ref. No. AB AB AB AB AB 159 Part No. QPLGN0342CEZZ QPLGN0761CEZZ QPLGN0447REZZ QPLGZ0883GEZZ QPLGN0361CEZZ QPLGN0578GEZZ QPLGN0978GEZZ QSOCN0911REN1 QSOCN0695REZZ QSOCZ0293GEZZ QSOCN2295REZZ QSOCN0795REZZ QSOCZ0292GEZZ QSOCN2295REZZ RRMCU0253CEZZ LHLDZ1962AJ00 LHLDZ1962AJ00 PSLDM0335PEFW PSLDM0336PEFW LHLDP1057PEZZ ★ J J J J J J J J J J J J J J J J J R R R Description Plug, 3-pin(OO) Plug, 7-pin Plug, 4-pin(TP3301-4) Plug, 8-pin(AC) Plug, 3-pin(OR) Plug, 5-pin(DB) Plug, 9-pin(OC) Socket, 9-pin(AH) Socket, 6-pin(AA) Socket, 2-pin(AE) Socket, 22-pin(SB) Socket, 7-pin(AD) Socket, 2-pin(AL) Socket, 22-pin(SA) R/C Receiver Holder (Start Sensor) Holder (End Sensor) Shield (H/A Top) Shield (H/A Bottom) Holder (Front LEDs) Code AA AD AA AD AB AB AC AD AB AC AD AC AC AD AG AD AD AC AC AD 27DV-S100 27DV-CS10 Ref. No. ★ Part No. Description Code INTEGRATED CIRCUITS J J J J J J PC817 PQ15RW11 TA78Dl09S KA7808AP PQ30RV11 PQ30RV11 AD AG AG AE AF AF TRANSISTORS Q901 Q902 Q9053 Q9054 Q9056 Q9057 Q9058 Q9059 Q9065 Q9073 Q9074 Q9075 Q9076 Q9077 Q9078 Q9079 VS2SK2624LS-G VS2SD2144S/-1 VS2SB1443TV1E VS2SB1443TV1E VS2SC3198-Y-1 VSKRA103M//-1 VS2SB1443TV1E VS2SC3198-Y-1 VS2SA1271-Y-1 VS2SA1271-Y-1 VS2SA1271-Y-1 VSKRC103M//-1 VSKRC102M//-1 VS2SA1271-Y-1 VS2SB1443TV1E VSKRC102M//-1 J J J J J J J J J J J J J J J J 2SK2624LS 2SD2144S 2SB1443TV 2SB1443TV 2SC3198-Y KRA103M 2SB1443TV 2SC3198-Y 2SA1271-Y 2SA1271-Y 2SA1271-Y KRC103M KRC102M 2SA1271-Y 2SB1443TV KRC102M AG AC AE AE AA AA AE AA AB AB AB AA AA AB AE AA DIODES D901 D902 D903 D904 å D905 D9010 D9011 D9052 D9053 D9054 D9058 D9065 D9071 D9075 D9091 D9092 D9093 D9094 VA901 RH-DX0083GEZZ VHD1F4G////-1 VHD1SS119//-1 RH-EX0645GEZZ RH-FX0034CEZZ or RH-FX0008GEZZ RH-DX0441CEZZ or RH-DX0279CEZZ or RH-DX0442CEZZ or RH-DX0443CEZZ RH-DX0460CEZZ VHD1F4G////-1 RH-DX0436CEZZ VHiMM1431AT-1 or VHiKiA431//-1 VHD1F4G////-1 VHD10ELS4//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-VX0019CEZZ å å å L901 L902 L903 L9001 L9002 RCiLF0320GEZZ RCiLF0313CEZZ RCiLF0314CEZZ RCiLP0184CEZZ RCiLP0147GEZZ å T901 RTRNW0022AJZZ å D906 D9001 D9003 D9004 D9006 J J J J J Diode Diode Diode Zener Diode PC817 ★ Description [EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film] å C901 RC-FZ037SCEZZ J 0.22 AC275V M-Poly. å C902 RC-FZ036SCEZZ J 0.1 AC275V M-Poly. C905 RC-EZ0463GEZZ J 100 200V EL. C906 VCFYZP2GA473K J 0.047 400V Plastic Film C907 RC-KZ0112GEZZ J 330p 2kV Ceramic C908 RC-KZ0112CEZZ J 100p 1kV Ceramic C909 VCQYTA1HM562J J 5600p 50V Mylar C910 VCQYTA1HM222K J 2200p 50V Mylar å C911 RC-KZ0098GEZZ J 150p AC250V Ceramic or RC-KZA0006WJZZ å C912 RC-KZ0098GEZZ J 150p AC250V Ceramic or RC-KZA0006WJZZ C913 VCKYPA1HB103K J 0.01 50V Ceramic C9001 VCEA0A1VW477M J 470 35V EL. C9002 VCEA0A1EW337M J 330 25V EL. C9003 VCEA0A1HW226M J 22 50V EL. C9004 RC-EZ1075CEZZ J 2200 10V EL. C9006 VCEA0A1AW228M J 2200 10V EL. C9009 VCQYTA1HM104K J 0.1 50V Mylar C9010 VCQYTA1HM104K J 0.1 50V Mylar C9011 VCEA0A1VW477M J 470 35V EL. C9012 VCEA0A2AW106M J 10 100V EL. C9021 VCEA0A0JW107M J 100 6.3V EL. C9052 VCEA0A0JW227M J 220 6.3V EL. C9053 VCEA0A1CW106M J 10 16V EL. C9055 VCEA0A1CW476M J 47 16V EL. C9056 VCEA0A1CW107M J 100 16V EL. C9057 VCEA0A0JW107M J 100 6.3V EL. C9058 VCEA0A0JW107M J 100 6.3V EL. C9059 VCEA0A1CW106M J 10 16V EL. C9060 VCKYPA1HB103K J 0.01 50V Ceramic C9061 VCEA0A0JW107M J 100 6.3V EL. C9062 VCEA0A1CW107M J 100 16V EL. C9063 VCEA0A1HW475M J 4.7 50V EL. C9064 VCEA0A1CW107M J 100 16V EL. C9065 VCEA0A1CW106M J 10 16V EL. C9072 VCEA0A0JW227M J 220 6.3V EL. C9073 VCEA0A1CW106M J 10 16V EL. C9075 VCEA9A1CW106M J 10 16V EL. DVD/VCR POWER Unit IC901 RH-FX0047CEZZ IC9021 VHiPQ15RW11-1 IC9051 VHiT78DL09S-1 IC9052 VHiKA7808AP-1 IC9053 VHiPQ30RV11-1 IC9054 VHiPQ30RV11-1 Part No. Code CAPACITORS DUNTKA637WEV1 å Ref. No. AC AC AB AB AE J Diode AC J J J J Diode Diode Diode MM1431ATT AF AC AG AE J J J J J J J J J J J J J J Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Varistor AC AD AB AB AB AB AB AB AB AB AB AB AB AC AD AC AG AC AD AB AA AA AD AD AA AB AC AB AF AD AC AC AB AC AB AB AB AB AC AB AB AB AA AB AC AB AC AB AB AB AB RESISTORS R902 R903 å COILS J J J J J Coil Coil Coil Coil Coil AF AH AL AE AC TRANSFORMER J Transformer AM 160 R904 R905 R906 R907 R908 R909 R910 R911 R912 R913 R914 R915 R9004 R9005 R9006 R9007 R9009 R9010 R9012 R9015 R9021 R9022 R9051 R9052 R9054 [M-Ox.··· Metal Oxide, M-Film··· Metal Film] RR-DZ0049CEZZ J 3.9M 1/2W Carbon RR-WZ0017GEZZ J 2.2 2W Cement or RR-WZ0002GEZZ RR-DZ0049CEZZ J 3.9M 1/2W Carbon VRS-VV3DB683J J 68k 2W M-Ox. VRD-RM2HD105J J 1.0M 1/2W Carbon VRD-RM2HD105J J 1.0M 1/2W Carbon VRD-RA2BE224J J 220k 1/8W Carbon VRN-VV3DBR56J J 0.56 2W M-Film VRD-RM2HD681J J 680 1/2W Carbon VRD-RM2HD561J J 560 1/2W Carbon VRD-RA2BE183J J 18k 1/8W Carbon VRD-RA2BE223J J 22k 1/8W Carbon VRD-RM2HD473J J 47k 1/2W Carbon VRD-RM2HD473J J 47k 1/2W Carbon VRD-RA2BE221J J 220 1/8W Carbon VRD-RA2BE272J J 2.7k 1/8W Carbon VRD-RA2BE102J J 1.0k 1/8W Carbon VRD-RA2BE332J J 3.3k 1/8W Carbon VRD-RA2BE102J J 1.0k 1/8W Carbon VRD-RA2BE102J J 1.0k 1/8W Carbon VRS-VV3AB152J J 1.5k 1W M-Ox. VRD-RA2BE471J J 470 1/8W Carbon VRN-RA2BK152F J 1.5k 1/8W M-Film VRN-RA2BK152F J 1.5k 1/8W M-Film VRD-RA2BE103J J 10k 1/8W Carbon VRD-RA2BE471J J 470 1/8W Carbon VRD-RA2BE103J J 10k 1/8W Carbon AB AD AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code ★ Part No. Description DUNTKA637WEV1 DUNTKA638WEV1 DVD/VCR POWER Unit (Continued) DEFLECTION Unit R9055 R9056 R9057 R9058 R9059 R9061 R9062 R9063 R9064 R9065 R9066 R9067 R9068 R9069 R9070 R9071 R9073 R9074 R9075 R9076 R9079 R9080 R9085 R9086 R9774 VRD-RA2EE821J VRD-RA2BE103J VRD-RA2BE471J VRD-RA2BE103J VRD-RM2HD221J VRD-RA2BE102J VRD-RA2BE472J VRD-RA2BE103J VRD-RA2BE104J VRD-RA2BE473J VRN-RA2BK272F VRN-RA2BK182F VRN-RA2BK333F VRN-RA2BK102F VRD-RA2BE123J VRN-RA2BK222F VRD-RA2BE103J VRD-RA2EE471J VRD-RA2BE103J VRD-RM2HD471J VRD-RA2BE103J VRD-RM2HD182J VRD-RA2BE103J VRD-RA2EE471J VRD-RA2BE102J F901 FB9001 FB9002 FH1 FH2 P901 P903 P9001 P9002 P9003 W901 W9001 W9002 W9003 W9004 W9005 W9006 QFS-B6321CEZZ RBLN-0090GEZZ~ RBLN-0090GEZZ~ QFSHD1013CEZZ QFSHD1014CEZZ QPLGN0360CEZZ QTiPM0083CEZZ QPLGN0578GEZZ QPLGN1178GEZZ QPLGN0978GEZZ PRDAF5021AJFW PRDAR0103AJFW PRDAR0104AJFW PRDAF3014AJFW PRDAR0103AJFW PRDAR0104AJFW PRDAR0104AJFW LHLDW1061PEKZ XBPSD30P10KS0 J J J J J J J J J J J J J J J J J J J J J J J J J 820 10k 470 10k 220 1.0k 4.7k 10k 100k 47k 2.7k 1.8k 33k 1.0k 12k 2.2k 10k 470 10k 470 10k 1.8k 10k 470 1.0k 1/4W 1/8W 1/8W 1/8W 1/2W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/4W 1/8W 1/2W 1/8W 1/2W 1/8W 1/4W 1/8W Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon M-Film M-Film M-Film M-Film Carbon M-Film Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS å Ref. No. J R R J J J J J J J J J J J J J J R J Fuse, 6.3A Ferrite Bead Ferrite Bead Fuse Holder Fuse Holder Plug, 3-pin(EB) Tip, (P52) Plug, 5-pin(SC) Plug, 11-pin(DD) Plug, 9-pin(OC) Heat Sink, for Q901 Heat Sink, for IC9053 Heat Sink, for IC9052 Heat Sink, for IC9054 Heat Sink, for IC9021 Heat Sink, for D9004 Heat Sink, for IC9051 Holder Screw AF AB AB AC AC AC AB AB AC AC AE AE AD AE AE AD AD AD AA Code INTEGRATED CIRCUITS IC5601 VHiLA7841//-1 IC5602 VHiTA1241AN-1 IC5610 VHiUPC358C/-1 IC5880 VHiUPC358C/-1 J J J J LA7841 TA1241AN UPC358C UPC358C AM AM AD AD TRANSISTORS Q5603 Q5604 Q5605 Q5606 Q5607 Q5608 Q5609 å Q5610 Q5611 å Q5612 VS2SC3198-Y-1 VS2SC5022//1E VS2SC3198-Y-1 VS2SC3198-Y-1 VS2SC3198-Y-1 VS2SC2482//-1 VS2SA1246//1E VS2SA1013//1E VS2SD1830//1E VS2SD2581//1E J J J J J J J J J J 2SC3198-Y 2SC5022 2SC3198-Y 2SC3198-Y 2SC3198-Y 2SC2482 2SA1246 2SA1013 2SD1830 2SD5681 AA AG AA AA AA AD AE AD AF AL DIODES D4623 D5601 D5602 D5603 D5604 D5605 D5606 D5607 D5610 D5611 D5612 å D5613 D5614 D5615 D5616 D5617 ' å D5618 D5619 D5620 D5621 D5623 D5624 D5625 D5626 D5627 D5628 å D5629 D5630 D5631 D5632 D5633 D5635 D5637 D5638 VHD1SS119//-1 RH-EX0619GEZZ VHD1SS119//-1 RH-EX0619GEZZ VHD1SS119//-1 RH-DX0511CEZZ VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-DX0295CEZZ RH-DX0487CEZZ RH-DX0514CEZZ RH-DX0302CEZZ RH-DX0295CEZZ RH-EX0656GEZZ RH-EX0672GEZZ RH-DX0487CEZZ RH-DX0295CEZZ RH-EX0654CEZZ VHD1SS119//-1 RH-EX0641GEZZ RH-EX0619GEZZ RH-EX0630GEZZ RH-DX0487CEZZ RH-EX0618GEZZ VHD1SS119//-1 RH-DX0229CEZZ RH-DX0511CEZZ VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-EX0619GEZZ VHD1SS119//-1 VHD1SS119//-1 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Diode Zener Diode, 6.2V Diode Zener Diode, 6.2V Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Zener Diode, 75V Zener Diode, 30V Diode Diode Zener Diode, 75V Diode Zener Diode, 12V Zener Diode, 6.2V Zener Diode, 9V Diode Zener Diode Diode Diode Diode Diode Diode Diode Zener Diode, 6.2V Diode Diode AB AA AB AA AB AE AB AB AB AD AC AF AC AD AC AB AC AD AD AB AA AA AA AC AA AB AF AE AB AB AB AA AB AB COILS L5601 L5602 L5604 L5606 L5607 L5608 RCiLZ1071CEZZ VP-XF8R2K0000 RCiLZ1005CEZZ RCiLZ1038CEZZ VP-DF220K0000 VP-XF101K0000 R J J J J J Coil Peaking 8.2µH Coil Coil Peaking 22µH Peaking 100µH AG AB AH AK AB AB TRANSFORMERS å å 'å T5601 RTRNZA001WJZZ R Transformer T5602 RTRNZ0731CEZZ J Transformer T5603 RTRNF2058CEZZ R H-Volt Transformer AL AG BE CONTROL R5632 RVR-M4333CEZZ 161 J 6.8k(B) Interlace Adj. AC 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code DUNTKA638WEV1 DEFLECTION Unit (Continued) CAPACITORS [EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film] C5603 VCFPVC3CA822H J 8200p 1.6kV M-Poly. C5605 VCEA0A1CW477M J 470 16V EL. C5606 VCEA0A1VW106M J 10 35V EL. å C5607 RC-KZ0149CEZZ R 390p 3.15kVCeramic C5608 RC-KZ0024CEZZ J 1000p 2kV Ceramic C5609 VCKYPA1HB391K J 390p 50V Ceramic C5610 VCQYTA1HM103J J 0.01 50V Mylar C5611 VCQYTA1HM103J J 0.01 50V Mylar C5612 VCKYPA1HB391K J 390p 50V Ceramic C5613 VCE9GA1HW335M J 3.3 50V EL. (N.P) C5614 VCSATA1CE225K J 2.2 16V Tantalum C5615 VCFYFA1HA224J J 0.22 50V Mylar C5616 VCQYTA1HM104J J 0.1 50V Mylar C5617 VCEAGA1HW474T J 0.47 50V EL. C5618 VCKYPA1HB103K J 0.01 50V Ceramic C5619 VCEA0A1EW476M J 47 25V EL. C5620 VCQYTA1HM104J J 0.1 50V Mylar C5621 VCEA0A1VW107M J 100 35V EL. C5622 VCKYPA1HB561K J 560p 50V Ceramic C5623 VCE9GA1CW106M J 10 16V EL. (N.P) C5624 VCKYPA2HB561K J 560p 500V Ceramic C5625 VCEA0A1CW227M J 220 16V EL. C5626 RC-EZ0724CEZZ J 100 160V EL. C5627 VCKYPA1HB472K J 4700p 50V Ceramic C5628 VCEA0A1VW227M J 220 35V EL. C5629 VCEA0A1EW108M J 1000 25V EL. C5630 RC-KZ0033CEZZ J 150p 2kV Ceramic C5631 RC-FZ0374CEZZ J 4.7 100V Mylar C5632 VCKYPA2HB102K J 1000p 500V Ceramic ' å C5633 VCFPVC3ZA802H R 8000p 1.8kV M-Poly. ' å C5634 VCQPPC2JB223J J 0.022 630V Polypro C5636 RC-FZ0272CEZZ J 0.39 100V Mylar C5637 VCKYPA1HF103Z J 0.01 50V Ceramic ' å C5639 VCFPVC3ZA882H R 8800p 1.8kV M-Poly. ' å C5640 VCQPPC2JB223J J 0.022 630V Polypro C5641 VCCSPA2HL7R0D J 7.0p 500V Ceramic C5642 RC-FZ0359CEZZ J 0.39 250V Mylar C5643 VCFYFA1HA563J J 0.056 50V Mylar C5644 VCKYPA1HB102K J 1000p 50V Ceramic C5645 VCKYPA2HB102K J 1000p 500V Ceramic C5646 VCQYTA2AA563K J 0.056 100V Mylar C5647 VCEA4A1HN107M J 100 50V EL. C5650 VCEA0A2EW106M J 10 250V EL. C5652 VCKYPA2HB102K J 1000p 500V Ceramic C5653 VCEA0A1VW107M J 100 35V EL. C5654 VCEA0A1EW108M J 1000 25V EL. C5655 VCKYPA2HB221K J 220p 500V Ceramic C5676 VCKYPA2HB102K J 1000p 500V Ceramic C5677 VCEA0A1EW107M J 100 25V EL. C5679 VCQYTA1HM103J J 0.01 50V Mylar AE AC AB AE AC AA AA AA AA AB AB AB AA AA AA AB AA AC AA AB AA AC AG AA AC AD AB AF AA AD AC AD AA AE AC AC AF AA AA AA AB AC AD AA AC AD AA AA AC AA RESISTORS R5607 R5608 R5609 R5610 R5611 R5612 R5613 R5614 R5615 R5616 R5617 R5618 R5619 R5620 R5621 R5622 R5623 [M-Ox.··· Metal Oxide, M-Film··· Metal Film] VRD-RA2BE271J J 270 1/8W Carbon VRD-RA2BE681J J 680 1/8W Carbon VRD-RA2BE103J J 10k 1/8W Carbon VRD-RA2BE271J J 270 1/8W Carbon VRD-RA2BE103J J 10k 1/8W Carbon VRD-RA2BE332J J 3.3k 1/8W Carbon VRS-VV3LB104J J 100k 3W M-Ox. VRS-SV3LB154J J 150k 3W M-Ox. VRD-RA2BE102J J 1.0k 1/8W Carbon VRC-MA2HG333K J 33k 1/2W Solid VRD-RA2BE183J J 18k 1/8W Carbon VRD-RA2BE103J J 10k 1/8W Carbon VRD-RA2BE394J J 390k 1/8W Carbon VRS-VV3AB181J J 180 1W M-Ox. VRD-RA2BE103J J 10k 1/8W Carbon VRD-RA2BE153J J 15k 1/8W Carbon VRD-RA2BE683J J 68k 1/8W Carbon AA AA AA AA AA AA AB AC AA AA AA AA AA AA AA AA AA Ref. No. R5624 R5625 R5626 R5627 R5628 R5629 R5631 R5633 R5634 R5635 R5636 R5638 R5640 R5642 R5643 R5644 R5645 R5646 R5648 R5649 R5650 R5651 R5652 R5653 å R5654 R5655 R5656 R5657 R5658 R5659 R5660 R5663 R5665 R5666 R5667 R5668 R5669 R5670 R5671 R5672 R5673 R5674 R5675 R5676 R5677 R5678 R5679 R5680 ' å R5681 å R5682 R5684 R5685 R5686 ' å R5687 ' å R5688 R5689 R5690 R5691 R5692 R5693 R5694 R5695 R5696 R5697 å R5698 R5699 R5700 R5701 R5702 R5703 R5704 R5705 R5706 R5707 R5708 162 Part No. VRD-RA2BE101J VRD-RA2BE102J VRD-RA2BE103J VRD-RA2BE333J VRD-RA2BE183J VRD-RA2BE103J VRD-RA2BE823J VRD-RA2BE823J VRD-RA2BE822J VRD-RA2BE184J VRD-RA2BE124J VRD-RA2BE334J VRD-RM2HD474J~ VRD-RM2HD183J VRD-RA2BE181J VRD-RA2BE332J VRD-RA2BE331J VRD-RA2EE562J VRD-RA2EE224J VRN-RA2BK154F VRS-KA3HG222J VRS-VV3AB562J VRD-RA2BE104J VRS-SV2HC820J VRW-KQ3NC3R3K VRN-RA2BK104F VRN-RA2BK104F VRD-RA2EE102J VRS-SV2HC102J VRN-RA2BK683F VRD-RA2BE563J VRD-RM2HD150J VRN-RA2BK223F VRN-RA2BK153F VRN-GA2EB1R0J VRN-VV3ABR22J VRN-GA2EB1R0J VRN-RA2BK332F VRN-RA2BK153F VRD-RA2BE102J VRN-VV3AB5R6J VRS-KT3LB122J VRN-RA2BK123F VRN-VV3DB1R5J VRD-RM2HD104J VRS-VV3DB331J VRD-RA2BE102J VRN-VV3LB1R8J VRN-GA2EB1R0J VRN-SV2HCR22J VRD-RA2EE274J VRD-RA2EE823J VRS-VV3AB102J VRD-RA2EE332G VRD-RA2EE392G VRS-VV3AB472J VRD-RA2BE102J VRD-RA2BE103J VRD-RA2BE102J VRD-RA2BE103J VRD-RA2BE822J VRD-RA2BE472J VRD-RM2HD182J VRN-VV3LB4R7J VRS-VV3AB103J VRS-SV2HC100J VRN-GA2EB1R0J VRD-RA2BE222J VRD-RA2BE562J VRD-RA2BE122J VRD-RM2HD102J VRD-RA2EE122G VRD-RA2BE223J VRD-RA2BE221J VRD-RA2BE824J ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 100 1/8W 1.0k 1/8W 10k 1/8W 33k 1/8W 18k 1/8W 10k 1/8W 82k 1/8W 82k 1/8W 8.2k 1/8W 180k 1/8W 120k 1/8W 330k 1/8W 470k 1/2W 18k 1/2W 180 1/8W 3.3k 1/8W 330 1/8W 5.6k 1/4W 220k 1/4W 150k 1/8W 2.2k 5W 5.6k 1W 100k 1/8W 82 1/2W 3.3 7W 100k 1/8W 100k 1/8W 1.0k 1/4W 1.0k 1/2W 68k 1/8W 56k 1/8W 15 1/2W 22k 1/8W 15k 1/8W 1.0 1/4W 0.22 1W 1.0 1/4W 3.3k 1/8W 15k 1/8W 1.0k 1/8W 5.6 1W 1.2k 3W 12k 1/8W 1.5 2W 100k 1/2W 330 2W 1.0k 1/8W 1.8 3W 1.0 1/4W 0.22 1/2W 270k 1/4W 82k 1/4W 1.0k 1W 3.3k 1/4W 3.9k 1/4W 4.7k 1W 1.0k 1/8W 10k 1/8W 1.0k 1/8W 10k 1/8W 8.2k 1/8W 4.7k 1/8W 1.8k 1/2W 4.7 3W 10k 1W 10 1/2W 1.0 1/4W 2.2k 1/8W 5.6k 1/8W 1.2k 1/8W 1.0k 1/2W 1.2k 1/4W 22k 1/8W 220 1/8W 820k 1/8W Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon M-Film M-Ox. M-Ox. Carbon M-Ox. Cement M-Film M-Film Carbon M-Ox. M-Film Carbon Carbon M-Film M-Film M-Film M-Film M-Film M-Film M-Film Carbon M-Film M-Ox. M-Film M-Film Carbon M-Ox. Carbon M-Film M-Film M-Film Carbon Carbon M-Ox. Carbon Carbon M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon Carbon M-Film M-Ox. M-Ox. M-Film Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Code AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AD AA AA AA AE AA AA AA AA AB AA AA AB AA AA AA AA AA AA AA AA AC AA AB AA AA AA AC AA AB AA AA AA AB AB AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code Ref. No. Description DUNTKA638WEV1 DUNTKA639WEV1 DEFLECTION Unit (Continued) TV POWER Unit MISCELLANEOUS PARTS FB5602 FB5603 FB5604 P5601 P5603 P5604 P5605 P5606 RDA5602 RDA5604 RDA5605 å ★ Part No. RDA5601 SG5601 SG5602 RBLN-0047CEZZ RBLN-0047CEZZ RBLN-0013GEZZ QPLGN0961CEZZ QPLGN0661CEZZ QPLGN0160FJZZ QPLGN0761CEZZ QPLGN0561CEZZ PRDAR0280PEFW PRDAR0277PEFW PRDAR0026PEFW PRDAR0336PEFW QSPGH0025CEZZ QSPGH0025CEZZ LHLDW1064PEKZ LHLDW1067PEKZ LX-BZ0086TAFD LX-BZ3049GEFD LX-BZ3100CEFD LX-TZ3004CEFD J J J J J J J J R R R R J J R R J J J J Ferrite Bead Ferrite Bead Ferrite Bead Plug, 9-pin(WA) Plug, 6-pin(BA) Plug, 5-pin(K) Plug, 7-pin(N) Plug, 5-pin(GA) Heat Sink, for IC5601 Heat Sink, for Q5611 Heat Sink, for Q5604 Heat Sink, for Q5612 Spark Gap Spark Gap Holder Holder Screw Screw Screw Screw Code INTEGRATED CIRCUITS AB AB AB AD AD AD AD AB AF AF AD AF AC AC AC AC AA AA AA AA IC6351 ' å IC9701 å IC9702 IC9740 IC9741 VHiAN5277//-1 VHiSTRF66291E RH-FX0008GEZZ VHiKA7812AP-1 VHiSE130N//-1 J J J J J AN5277 STRF6629B PC123FY8 KA7812AP SE130N AN AT AE AE AF TRANSISTORS Q9740 VS2SC3198-Y-1 Q9741 VS2SC3198-G-1 Q9752 VS2SA1266-Y-1 J 2SC3198-Y J 2SC3198-G J 2SA1266-Y AA AA AA DIODES D9701 D9702 D9703 D9704 D9705 D9706 D9708 D9720 D9724 D9726 D9728 D9729 D9741 D9742 D9744 D9751 D9752 D9753 D9755 D9760 RH-DX0485CEZZ RH-DX0321CEZZ RH-DX0066GEZZ VHD1SS244//-1 VHD1SS244//-1 RH-EX0610GEZZ RH-EX0673GEZZ RH-DX0452CEZZ RH-DX0436CEZZ RH-DX0473CEZZ RH-DX0460CEZZ RH-DX0295CEZZ RH-EX0640GEZZ VHD1SS119//-1 RH-EX0655GEZZ VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-EX0607GEZZ RH-EX0641GEZZ J J J J J J J J J J J J J J J J J J J J Diode Diode Diode Diode Diode Zener Diode, 4,7V Zener Diode, 30V Diode Diode Diode Diode Diode Zener Diode, 12V Diode Zener Diode, 20V Diode Diode Diode Zener Diode, 4.4V Zener Diode, 12V AG AC AB AB AB AA AB AH AG AK AF AD AA AB AB AB AB AB AA AA PACKAGED CIRCUIT PR9701 RMPTP0085CEZZ J Packaged Circuit AL COILS L9720 RCiLP0218CEZZ L9724 RCiLP0212CEZZ L9726 RCiLP0219CEZZ J Coil 33µH J Coil 10µH J Coil 39µH AD AD AD TRANSFORMER å T9701 RTRNWA004WJZZ R Transformer AR CAPACITORS [EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film] C6355 VCQYTA1HM123K J 0.012 50V Mylar C6356 VCEA0A1HW105M J 1.0 50V EL. C6357 VCEA0A1EW107M J 100 25V EL. C6358 VCEA0A1HW105M J 1.0 50V EL. C6359 VCEA0A1EW477M J 470 25V EL. C6360 VCEA0A1CW106M J 10 16V EL. C6361 VCEA0A1VW108M J 1000 35V EL. C6362 VCKYPA1HF103Z J 0.01 50V Ceramic C6363 VCEA0A1HW225M J 2.2 50V EL. C6364 VCEA0A1EW477M J 470 25V EL. C6366 VCQYTA1HM123K J 0.012 50V Mylar C9704 RC-KZ0016CEZZ J 0.01 AC250V Ceramic C9705 RC-KZ0016CEZZ J 0.01 AC250V Ceramic C9707 RC-EZ0617CEZZ R 1000 200V EL. C9708 VCQPPB2GB473K J 0.047 400V Polypro C9709 RC-KZ0300CEZZ J 1000p 2kV Ceramic C9710 RC-KZ0290CEZZ J 150p 2kV Ceramic C9711 VCEA0A1VW107M J 100 35V EL. C9712 VCQYTA1HM102J J 1000p 50V Mylar C9713 VCFPVC3CA432H J 4300p 1.6kV M-Poly. C9714 RC-KZ0296CEZZ J 470p 2kV Ceramic C9715 VCKYPA2HB471K J 470p 500V Ceramic å C9717 RC-KZ0093GEZZ J 4700p AC250V Ceramic 163 AA AB AC AB AD AB AD AA AB AD AA AC AC AT AD AC AC AC AA AE AC AA AD 27DV-S100 27DV-CS10 Ref. No. ★ Part No. Description Code TV POWER Unit (Continued) å C9718 C9720 C9721 C9722 C9723 C9724 C9725 C9726 C9727 C9728 C9729 C9731 C9741 C9742 C9743 C9744 C9753 ★ Description J 22k 2W J 470 1/8W J 470 1/8W M-Ox. Carbon Carbon Code AA AA AA MISCELLANEOUS PARTS J 4700p AC250V Ceramic AD J 330 160V EL. AH J 470p J 100 2kV Ceramic 160V EL. AC AG J 470p J 1000 2kV 16V Ceramic EL. AC AD J 100 J 680 16V 25V EL. EL. AC AD J 100 J 1000 35V 35V EL. EL. AC AF J J J J J J J 50V 25V 100V 50V 25V 16V 50V EL. (N.P) EL. EL. EL. EL. EL. Ceramic AB AC AB AB AB AC AA 1.0 330 1.0 2.2 47 220 330p RY9701 RRLYJ0088CEZZ or RRLYJ0079CEZZ FB9702 RBLN-0047CEZZ FB9703 RBLN-0090GEZZ~ FB9704 RBLN-0090GEZZ~ FB9720 RBLN-0091GEZZ FB9728 RBLN-0020CEZZ P6351 QPLGN0461CEZZ P6352 QPLGN0578GEZZ P9701 QPLGN0361CEZZ P9702 QPLGN0360CEZZ P9705 QPLGN0260CEZZ P9711 QPLGN0561CEZZ P9712 QPLGZ1040CEZZ P9713 QPLGZ0613CEZZ P9801 QPLGN0561CEZZ RDA9701 PRDAR5222CEFW RDA9702 PRDAR0139PEFW RDA9720 PRDAR0083PEFW RDA9740 PRDAF3014AJFW RDA9703 PRDAR0299PEFW QCNW-2591PEZZ LHLDW1064PEKZ LX-BZ0086TAFD LX-BZ3100CEFD RESISTORS R6353 R6357 R6360 R6369 R9701 R9703 R9704 R9705 R9706 R9707 R9708 R9709 R9710 R9711 R9712 R9713 å R9717 R9720 R9724 R9726 R9727 R9728 R9729 R9730 R9741 R9742 R9743 R9744 R9745 R9746 R9747 R9748 R9749 R9757 R9758 R9761 R9771 Part No. R9772 VRS-VV3DB223J R9880 VRD-RA2BE471J R9881 VRD-RA2BE471J DUNTKA639WEV1 or RC-KZ0286CE RC-KZ0093GEZZ or RC-KZ0286CE RC-EZ0535CEZZ or RC-EZ0003SE RC-KZ0296CEZZ RC-EZ0724CEZZ or RC-EZ0004SE RC-KZ0296CEZZ RC-EZ1086CEZZ or RC-EZ0005SE VCEA0A1CW107M RC-EZ1099CEZZ or RC-EZ0006SE VCEA0A1VW107M RC-EZ1100CEZZ or RC-EZ0002SE VCE9GA1HW105M VCEA0A1EW337M VCEA0A2AW105M VCEA0A1HW225M VCEA0A1EW476M VCEA0A1CW227M VCKYPA1HB331K Ref. No. [M-Ox.··· Metal Oxide, M-Film··· Metal Film] VRD-RA2BE392J J 3.9k 1/8W Carbon VRD-RA2BE102J J 1.0k 1/8W Carbon VRD-RA2BE392J J 3.9k 1/8W Carbon VRN-GA2EB1R0J J 1.0 1/4W M-Film VRW-KQ4AC1R2K J 1.2 10W Cement VRS-VV3DB183J J 18k 2W M-Ox. VRD-RM2HD154J J 150k 1/2W Carbon VRS-KT3LB333J J 33k 3W M-Ox. VRN-SV2HC4R7J J 4.7 1/2W M-Film VRN-GA2EB1R0J J 1.0 1/4W M-Film VRD-RA2EE102J J 1.0k 1/4W Carbon VRD-RA2EE122J J 1.2k 1/4W Carbon VRD-RA2EE272J J 2.7k 1/4W Carbon VRS-SV2HC681J J 680 1/2W M-Ox. VRN-VV3DBR12J J 0.12 2W M-Film VRN-VV3DBR15J J 0.15 2W M-Film RR-DZ0049CEZZ J 3.9M 1/2W Carbon VRD-RM2HD683J J 68k 1/2W Carbon VRD-RM2HD561J J 560 1/2W Carbon VRN-VV3ABR10J J 0.1 1W M-Film VRD-RM2HD122J J 1.2k 1/2W Carbon VRN-VV3ABR10J J 0.1 1W M-Film VRD-RM2HD272J J 2.7k 1/2W Carbon VRD-RM2HD272J J 2.7k 1/2W Carbon VRD-RA2EE102J J 1.0k 1/4W Carbon VRD-RA2BE182J J 1.8k 1/8W Carbon VRD-RM2HD470J J 47 1/2W Carbon VRS-VV3DB330J J 33 2W M-Ox. VRD-RA2BE472J J 4.7k 1/8W Carbon VRD-RA2BE103J J 10k 1/8W Carbon VRD-RA2BE392J J 3.9k 1/8W Carbon VRD-RA2BE472J J 4.7k 1/8W Carbon VRD-RA2BE103J J 10k 1/8W Carbon VRD-RA2BE182J J 1.8k 1/8W Carbon VRD-RA2BE563J J 56k 1/8W Carbon VRD-RA2BE472J J 4.7k 1/8W Carbon VRD-RA2BE102J J 1.0k 1/8W Carbon AA AA AA AA AE AA AA AC AA AA AA AA AA AA AB AB AB AA AA AB AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 164 J Relay AH J R R J J J J J J J J J J J J R R J R R R J J AB AB AB AB AB AB AB AB AC AC AB AE AD AB AH AC AD AE AH AD AC AA AA Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Plug, 4-pin(SE) Plug, 5-pin(ZA) Plug, 3-pin(OR) Plug, 3-pin(EB) Plug, 2-pin(M) Plug, 5-pin(GA) Plug, 10-pin(XB) Plug, 6-pin(XC) Plug, 5-pin Heat Sink, for IC9701 Heat Sink, for D9701 Heat Sink for D9720 Heat Sink, for IC9740 Heat Sink, for IC6351 Connecting Cord(K3) Holder Screw Screw 27DV-S100 27DV-CS10 Ref. No. ★ Part No. Description Code D4805 D4806 D4807 D4808 D4901 D4902 DUNTKA640WEV1 TERMINAL Unit TUNER NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY. å TU1951 VTUVTBT5UB202 J Tuner-B å TU2101 VTUVTBT5UR202 J Tuner-A Ref. No. VHiCXA2079Q-1 VHiKA7805AP-1 VHiNJM2230M-1 VHiZ86129S+-1~ VHiTC4W53F/-1 VHiCXA2064M-1 RH-iX3113CEZZ VHiBR24C04F-1 VHiKA7809AP-1 VHiKA7805AP-1 VHiMM1510XN-1 Q1302 Q1303 Q1371 Q1951 Q1952 Q2501 Q2617 Q2618 ' å Q2808 Q4403 Q4404 Q4405 Q4406 Q4409 Q4410 Q4901 Q4902 Q4903 Q4904 Q4905 Q4906 Q4907 VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SA812-M/1E VS2SA812-M/1E VS2SC1623L51E VSKRC103S//-1 VS2SC1623L51E VS2SC1623L51E VS2SA1266-Y-1 VS2SK30AG//2E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC3198-Y-1 VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VSKRC102S//-1 D1301 D1302 D1303 D1304 D1306 D1951 D2101 D2501 D2502 D2612 D4405 D4406 D4412 D4413 D4414 D4617 D4619 D4620 D4621 D4622 D4625 D4721 D4745 D4801 D4802 D4803 D4804 RH-EX0631GEZZ RH-EX0631GEZZ RH-EX0631GEZZ RH-EX0631GEZZ RH-EX0631GEZZ RH-EX0673GEZZ RH-EX0673GEZZ VHD1SS119//-1 VHD1SS119//-1 RH-EX0609GEZZ RH-EX0628GEZZ VHD1SS119//-1 RH-EX0618GEZZ RH-EX0618GEZZ RH-EX0618GEZZ RH-EX0631GEZZ VHD1SS119//-1 RH-EX0604GEZZ RH-EX0616GEZZ RH-EX0616GEZZ RH-EX0631GEZZ VHD1SS119//-1 RH-DX0441CEZZ VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 J J J R J J J J J J J CXA2079Q KA7805API NJM2230M Z8612912SSC TC4W53F CXA2064M TA1276AN BR24C04F-WE2 KA7809API KA7805API MM1510XNRE 2SC1623L5 2SC1623L5 2SC1623L5 2SA812-M 2SA812-M 2SC1623L5 KRC103S 2SC1623L5 2SC1623L5 2SA1266-Y 2SK30AG 2SC1623L5 2SC1623L5 2SC1623L5 2SC3198-Y 2SC1623L5 2SC1623L5 2SC1623L5 2SC1623L5 2SC1623L5 2SC1623L5 KRC102S Zener Diode, 9V Zener Diode, 9V Zener Diode, 9V Zener Diode, 9V Zener Diode, 9V Zener Diode, 32V Zener Diode, 32V Diode Diode Zener Diode Zener Diode, 8.2V Diode Zener Diode, 6.2V Zener Diode, 6.2V Zener Diode, 6.2V Zener Diode, 9V Diode Zener Diode, 3.9V Zener Diode, 6.2V Zener Diode, 6.2V Zener Diode, 9V Diode Diode Diode Diode Diode Diode J J J J J J Diode Diode Diode Diode Diode Diode Code AB AB AB AB AB AB AL FILTERS AND COILS AQ AE AH AZ AE AR AZ AG AE AE AE CF4501 FL2601 L1301 L2602 L4401 L4404 L4405 RFiLA0034CEZZ RFiLN0044GEZZ VP-DF101K0000 VP-DF101K0000 VP-XF4R7K0000 VP-XF4R7K0000 VP-XF4R7K0000 J J J J J J J Ceramic Filter Filter Peaking 100µH Peaking 100µH Peaking 4.7µH Peaking 4.7µH Peaking 4.7µH AD AB AB AB AB AB AB CONTROLS R3601 RVR-M4790GEZZ R3612 RVR-M4784GEZZ R3614 RVR-M4786GEZZ J 47k(B) Separation Wideband Adj. AC J 4.7k(B) Separation Spectal Adj. AB J 10k(B) Input Level Adj. AB CAPACITORS AB AB AB AC AC AB AA AB AB AA AD AB AB AB AA AB AB AB AB AB AB AA C1301 C1302 C1303 C1304 C1305 C1306 C1307 C1308 C1309 C1310 C1311 C1312 C1313 C1314 C1315 C1316 C1317 C1318 C1319 C1320 C1321 C1322 C1327 C1328 C1331 C1332 C1333 C1334 C1335 C1336 C1342 C1343 C1351 C1352 C1353 C1361 C1371 C1724 C1725 C1726 C1951 C1952 C1953 C1954 C1955 C1957 C1958 C1959 C1966 DIODES J J J J J J J J J J J J J J J J J J J J J J J J J J J VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 Description X4801 RCRSB0001PEZZ R Crystal 3.58MHz TRANSISTORS J J J J J J J J J J J J J J J J J J J J J J ★ PACKAGED CIRCUIT BD BC INTEGRATED CIRCUITS IC1301 IC1902 IC1951 IC2501 IC2602 IC3601 IC4401 IC4402 å IC4740 å IC4741 IC4951 Part No. AA AA AA AA AA AB AB AB AB AA AC AB AA AA AA AA AB AB AA AA AA AB AC AB AB AB AB 165 [EL.··· Electrolytic] VCKYCY1CB104K J 0.1 16V VCKYCY1HF103Z J 0.01 50V VCEA0A1CW106M J 10 16V VCEA0A1CW106M J 10 16V VCEA9A1HW105M J 1.0 50V VCEA9A1CW106M J 10 16V VCEA9A1CW106M J 10 16V VCEA9A1HW105M J 1.0 50V VCEA9A1CW106M J 10 16V VCEA9A1CW106M J 10 16V VCEA0A1HW105M J 1.0 50V VCEA9A1CW106M J 10 16V VCEA9A1CW106M J 10 16V VCEA0A1HW105M J 1.0 50V VCKYD41CY103N J 0.01 16V VCEA9A1HW105M J 1.0 50V VCEA9A1CW106M J 10 16V VCEA9A1CW106M J 10 16V VCEA9A1HW105M J 1.0 50V VCEA9A1CW106M J 10 16V VCEA9A1CW106M J 10 16V VCKYCY1CB104K J 0.1 16V VCKYCY1HB271K J 270p 50V VCKYCY1HB271K J 270p 50V VCKYCY1CB104K J 0.1 16V VCEA0A1HW105M J 1.0 50V VCKYCY1HF103Z J 0.01 50V VCKYCY1CB104K J 0.1 16V VCEA0A1CW106M J 10 16V VCEA0A1CW106M J 10 16V VCEA9A1CW106M J 10 16V VCEA9A1CW106M J 10 16V VCEA0A1CW107M J 100 16V VCKYCY1EB103K J 0.01 25V VCEA0A1CW226M J 22 16V VCKYCY1CB104K J 0.1 16V VCKYCY1CB104K J 0.1 16V VCKYCY1CB104K J 0.1 16V VCKYCY1CB104K J 0.1 16V VCKYCY1CB104K J 0.1 16V VCKYPA1HF103Z J 0.01 50V VCEA0A0JW108M J 1000 6.3V VCEA0A1HW105M J 1.0 50V VCQYTA1HM104K J 0.1 50V VCQYTA1HM473J J 0.047 50V VCQYTA1HM472J J 4700p 50V VCQYTA1HM472J J 4700p 50V VCEA0A1HW105M J 1.0 50V VCEA0A1HW105M J 1.0 50V Ceramic Ceramic EL. EL. EL. EL. EL. EL. EL. EL. EL. EL. EL. EL. Ceramic EL. EL. EL. EL. EL. EL. Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic EL. EL. EL. EL. EL. Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. Mylar Mylar Mylar Mylar EL. EL. AB AA AB AB AB AB AB AB AB AB AB AB AB AB AA AB AB AB AB AB AB AB AA AA AB AB AA AB AB AB AB AB AC AA AB AB AB AB AB AB AA AC AB AC AA AB AB AB AB 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code DUNTKA640WEV1 TERMINAL Unit (Continued) C1967 C1982 C1983 C2101 C2102 C2103 C2501 C2502 C2503 C2504 C2505 C2506 C2507 C2508 C2512 C2650 C2652 C2657 C2658 C2659 C2660 C2822 C3601 C3602 C3603 C3604 C3605 C3606 C3607 C3608 C3609 C3610 C3611 C3612 C3613 C3614 C3615 C3616 C3617 C3618 C3619 C4104 C4105 C4401 C4402 C4403 C4404 C4405 C4406 C4407 C4408 C4409 C4410 C4411 C4412 C4417 C4418 C4420 C4425 C4426 C4427 C4430 C4431 C4440 C4447 C4499 C4601 C4613 C4616 C4617 C4618 VCEA0A1HW105M VCEA0A1HW106M VCEA0A1EW476M VCKYCY1HF103Z VCEA0A0JW108M VCEA0A1HW105M VCKYCY1CF104Z VCKYCY1CB683K VCKYCY1HB682K VCEA0A1HW106M VCKYCY1CB104K VCKYCY1HB561K VCKYCY1CB104K VCEA0A1HW475M VCEA9M1CW226M VCKYCY1CB104K VCKYCY1EB103K VCEA0A0JW476M VCEA0A1CW106M VCKYCY1EB103K VCEA0A0JW107M VCEA0A1HW106M VCEA9A1HW475M VCEA9A1HW475M VCEA0A1CW476M VCKYCY1CF104Z VCEA9A1HW475M VCEA9A1CW106M VCEA9A1HW475M VCEA9A1CW106M VCEA0A1HW105M VCKYCY1HB562K VCKYCY1EB123K VCE9GA1HW475M VCEA9A1HW105M VCEA9A1CW106M VCE9GA1HW475M VCEA0A1HW335M VCE9GA1HW475M VCKYCY1CB473K VCKYCY1HB272K VCKYCY1CB104K VCEA0A1CW476M VCEA0A1CW337M VCEA0A1VW226M VCKYCY1EB103K VCEA0A1HW105M VCEA0A1HW225M VCKYCY1EB103K VCEA0A1CW337M VCEA0A1HW474M VCFYFA1HA334J VCEA0A1HW105M VCKYCY1HF103Z VCCCCY1HH270J VCKYPA1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB471K VCKYCY1HF103Z VCFYFA1HA104J VCEA0A1EW476M VCKYPA1HF103Z VCKYCY1EB103K VCEA0A1CW337M VCKYCY1CF104Z VCFYFA1HA103J+ VCKYCY1EB103K VCEA0A1HW225M VCEA0A1HW225M VCFYFA1HA223J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 1.0 10 47 0.01 1000 1.0 0.1 0.068 6800p 10 0.1 560p 0.1 4.7 22 0.1 0.01 47 10 0.01 100 10 4.7 4.7 47 0.1 4.7 10 4.7 10 1.0 5600p 0.012 4.7 1.0 10 4.7 3.3 4.7 0.047 2700p 0.1 47 330 22 0.01 1.0 2.2 0.01 330 0.47 0.33 1.0 0.01 27p 0.01 0.01 0.01 470p 0.01 0.1 47 0.01 0.01 330 0.1 0.01 0.01 2.2 2.2 0.022 50V 50V 25V 50V 6.3V 50V 16V 16V 50V 50V 16V 50V 16V 50V 16V 16V 25V 6.3V 16V 25V 6.3V 50V 50V 50V 16V 16V 50V 16V 50V 16V 50V 50V 25V 50V 50V 16V 50V 50V 50V 16V 50V 16V 16V 16V 35V 25V 50V 50V 25V 16V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 50V 25V 16V 16V 50V 25V 50V 50V 50V EL. EL. EL. Ceramic EL. EL. Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic EL. EL. Ceramic Ceramic EL. EL. Ceramic EL. EL. EL. EL. EL. Ceramic EL. EL. EL. EL. EL. Ceramic Ceramic EL. (N.P) EL. EL. EL. (N.P) EL. EL. (N.P) Ceramic Ceramic Ceramic EL. EL. EL. Ceramic EL. EL. Ceramic EL. EL. Mylar EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Mylar EL. Ceramic Ceramic EL. Ceramic Mylar Ceramic EL. EL. Mylar AB AB AB AA AC AB AA AC AA AB AB AA AB AB AB AB AA AB AB AA AB AB AB AB AB AA AB AB AB AB AB AA AA AB AB AB AB AB AB AA AA AB AB AC AB AA AB AB AA AC AB AB AB AA AA AA AA AA AA AA AA AB AA AA AC AA AB AA AB AB AB Ref. No. ★ Part No. J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description C4619 C4620 C4621 C4622 C4743 C4744 C4745 C4746 C4803 C4805 C4806 C4807 C4812 C4813 C4814 C4817 C4818 C4819 C4843 C4844 C4845 C4850 C4851 C4852 C4901 C4903 C4904 C4905 C4906 C4907 C4908 C4921 C4922 C4930 C4931 C4950 C4951 C4952 C4953 C4954 C4955 C4956 VCEA0A1CW477M VCKYCY1HB271K VCKYCY1HB152K VCCCCY1HH471J VCEA0A1EW476M VCEA0A1CW227M VCEA0A1CW108M VCEA0A1HW106M VCKYCY1HF103Z VCKYCY1EB103K VCKYCY1CB104K VCEA0A1HW225M VCEAGA1HW224T VCQYTA1HM222J VCCCCY1HH110J VCCCCY1HH1R0C VCKYCY1CB104K VCKYCY1CB104K VCKYCY1EB103K VCKYCY1EB103K VCKYCY1EB103K VCKYCY1EB103K VCKYCY1EB103K VCKYCY1EB103K VCEA0A1HW475M VCEA0A1HW475M VCEA0A1CW106M VCEA0A1CW476M VCQYTA1HM102J VCEA0A1CW106M VCQYTA1HM102J VCEA9A1HW105M VCEA9A1HW105M VCEA0A1HW225M VCEA0A1HW225M VCQYTA1HM104K VCEA9A1HW105M VCEA9A1CW476M VCEA0A1CW226M VCEA0A1CW107M VCEA0A1CW106M VCEA0A1CW337M 470 270p 1500p 470p 47 220 1000 10 0.01 0.01 0.1 2.2 0.22 2200p 11p 1.0p 0.1 0.1 0.01 0.01 0.01 0.01 0.01 0.01 4.7 4.7 10 47 0.001 10 0.001 1.0 1.0 2.2 2.2 0.1 1.0 47 22 100 10 330 16V 50V 50V 50V 25V 16V 16V 50V 50V 25V 16V 50V 50V 50V 50V 50V 16V 16V 25V 25V 25V 25V 25V 25V 50V 50V 16V 16V 50V 16V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 16V 16V R1301 R1302 R1303 R1304 R1305 R1306 R1307 R1309 R1310 R1311 R1312 R1313 R1314 R1315 R1316 R1317 R1318 R1319 R1320 R1321 R1325 R1326 R1327 R1329 R1331 R1332 R1333 R1334 R1335 R1336 [M-Ox.··· Metal Oxide] VRD-RA2BE101J J 100 1/8W VRD-RA2BE101J J 100 1/8W VRD-RA2BE153J J 15k 1/8W VRD-RA2BE153J J 15k 1/8W VRS-CY1JF221J J 220 1/16W VRS-CY1JF123J J 12k 1/16W VRS-CY1JF123J J 12k 1/16W VRD-RA2BE123J J 12k 1/8W VRD-RA2BE123J J 12k 1/8W VRD-RA2BE101J J 100 1/8W VRD-RA2BE123J J 12k 1/8W VRD-RA2BE123J J 12k 1/8W VRD-RA2BE101J J 100 1/8W VRD-RA2BE101J J 100 1/8W VRS-CY1JF221J J 220 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF221J J 220 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF272J J 2.7k 1/16W VRS-CY1JF822J J 8.2k 1/16W VRS-CY1JF222J J 2.2k 1/16W VRS-CY1JF101J J 100 1/16W VRS-CY1JF101J J 100 1/16W VRS-CY1JF472J J 4.7k 1/16W VRS-CY1JF101J J 100 1/16W VRS-CY1JF100J J 10 1/16W VRS-CY1JF561J J 560 1/16W VRS-CY1JF561J J 560 1/16W EL. Ceramic Ceramic Ceramic EL. EL. EL. EL. Ceramic Ceramic Ceramic EL. EL. Mylar Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. EL. EL. Mylar EL. Mylar EL. EL. EL. EL. Mylar EL. EL. EL. EL. EL. EL. Code AC AA AA AA AB AC AD AB AA AA AB AB AB AA AA AA AB AB AA AA AA AA AA AA AB AB AB AB AA AB AA AB AB AB AB AC AB AB AB AC AB AC RESISTORS 166 Carbon Carbon Carbon Carbon M-Ox. M-Ox. M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. AB AB AA AA AA AA AA AA AA AB AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code R4110 R4111 R4112 R4114 R4115 R4116 R4117 R4126 R4127 R4128 R4401 R4402 R4403 R4405 R4406 R4407 R4410 R4411 R4412 R4413 R4414 R4415 R4416 R4425 R4428 R4432 R4434 R4435 R4436 R4437 R4438 R4439 R4440 R4441 R4444 R4445 R4448 R4449 R4455 R4456 R4461 R4462 R4463 R4464 R4465 R4466 R4540 R4541 R4603 R4613 R4616 R4617 R4620 R4627 R4744 R4803 R4805 R4806 R4807 R4814 R4817 R4823 R4827 R4828 R4829 R4830 R4852 R4854 R4856 R4904 R4905 R4906 R4907 R4908 R4911 R4912 DUNTKA640WEV1 TERMINAL Unit (Continued) R1337 R1338 R1351 R1352 R1360 R1361 R1365 R1372 R1373 R1374 R1379 R1951 R1952 R1953 R1954 R1956 R1957 R1958 R1959 R1960 R1961 R1962 R1968 R1969 R2101 R2102 R2103 R2104 R2105 R2501 R2502 R2503 R2504 R2505 R2506 R2507 R2508 R2509 R2510 R2511 R2512 R2513 R2514 R2515 R2516 R2520 R2521 R2526 R2528 R2529 R2668 R2669 R2670 R2672 R2673 R2674 R2675 R2676 R2677 R2678 ' å R2808 R3110 R3602 R3603 R3604 R3605 R3606 R3607 R3608 R3610 R3611 R3613 VRS-CY1JF564J VRS-CY1JF564J VRD-RA2BE101J VRD-RA2BE101J VRS-CY1JF000J VRD-RA2BE101J VRD-RA2BE221J VRS-CY1JF222J VRS-CY1JF222J VRD-RA2BE101J VRS-CY1JF222J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J VRD-RA2BE1R0J VRS-CY1JF102J VRS-CY1JF151J VRS-CY1JF122J VRS-CY1JF684J VRS-CY1JF122J VRD-RA2BE272J VRS-CY1JF272J VRS-CY1JF562J VRS-CY1JF122J QJUM-3001CEFW VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE1R0J VRS-CY1JF182J VRS-CY1JF272J VRS-CY1JF472J VRS-CY1JF472J VRS-CY1JF472J VRS-CY1JF562J VRS-CY1JF682J VRS-CY1JF103J VRS-CY1JF562J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF471J VRS-CY1JF470J VRS-CY1JF223J VRS-CY1JF222J VRS-CY1JF223J VRS-CY1JF471J VRS-CY1JF562J VRS-CY1JF223J VRS-CY1JF000J VRS-CY1JF101J VRD-RA2BE223J VRD-RA2BE273J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF000J VRS-CY1JF272J VRD-RA2BE151J VRD-RM2HD101J VRS-CY1JF103J VRS-CY1JF681J VRD-RA2BE103J VRS-CY1JF101J VRS-CY1JF683F VRS-CY1JF183J VRS-CY1JF103J VRS-CY1JF105J VRS-CY1JF104J VRS-CY1JF103J VRD-RA2BE103J VRD-RA2BE103J VRS-CY1JF392J VRS-CY1JF332J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 560k 1/16W 560k 1/16W 100 1/8W 100 1/8W 0 1/16W 100 1/8W 220 1/8W 2.2k 1/16W 2.2k 1/16W 100 1/8W 2.2k 1/16W 0 1/16W 100 1/16W 100 1/16W 1.0 1/8W 1.0k 1/16W 150 1/16W 1.2k 1/16W 680k 1/16W 1.2k 1/16W 2.7k 1/8W 2.7k 1/16W 5.6k 1/16W 1.2k 1/16W 0 100 1/8W 100 1/8W 1.0 1/8W 1.8k 1/16W 2.7k 1/16W 4.7k 1/16W 4.7k 1/16W 4.7k 1/16W 5.6k 1/16W 6.8k 1/16W 10k 1/16W 5.6k 1/16W 100 1/16W 100 1/16W 470 1/16W 47 1/16W 22k 1/16W 2.2k 1/16W 22k 1/16W 470 1/16W 5.6k 1/16W 22k 1/16W 0 1/16W 100 1/16W 22k 1/8W 27k 1/8W 4.7k 1/16W 10k 1/16W 4.7k 1/16W 0 1/16W 2.7k 1/16W 150 1/8W 100 1/2W 10k 1/16W 680 1/16W 10k 1/8W 100 1/16W 68k 1/16W 18k 1/16W 10k 1/16W 1.0M 1/16W 100k 1/16W 10k 1/16W 10k 1/8W 10k 1/8W 3.9k 1/16W 3.3k 1/16W M-Ox. M-Ox. Carbon Carbon M-Ox. Carbon Carbon M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. T-jumper Carbon Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. Ref. No. AA AA AB AB AA AB AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 167 Part No. VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRD-RA2BE471J VRS-CY1JF750J VRS-CY1JF750J VRS-CY1JF750J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF562J VRS-CY1JF223J VRD-RA2EE680J VRS-CY1JF471J VRS-CY1JF471J VRD-RA2BE103J VRS-CY1JF820J VRS-CY1JF820J VRS-CY1JF820J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF474J VRS-CY1JF101J VRS-CY1JF823J VRS-CY1JF124J VRS-CY1JF395J VRS-CY1JF332J VRS-CY1JF154J VRS-CY1JF333J VRS-CY1JF273J VRS-CY1JF101J VRS-CY1JF471J VRS-CY1JF471J VRS-CY1JF102J VRS-CY1JF151J VRS-CY1JF100J VRS-CY1JF101J VRD-RA2EE152J VRS-CY1JF182J VRS-CY1JF393J VRS-CY1JF273J VRS-CY1JF393J VRS-CY1JF221J VRS-CY1JF471J VRS-CY1JF391J VRS-CY1JF101J VRD-RA2EE331J VRS-CY1JF332J VRD-RA2BE182J VRS-CY1JF103J VRD-RA2BE153J VRS-SV2HC680J VRS-VV3DB330J VRS-CY1JF101J VRS-CY1JF122J VRS-CY1JF561J VRD-RA2BE102J VRS-CY1JF332J VRS-CY1JF273J VRS-CY1JF102J VRD-RA2BE181J VRD-RA2BE181J VRS-CY1JF822J VRS-CY1JF101J VRS-CY1JF391J VRS-CY1JF391J VRS-CY1JF391J VRS-CY1JF683J VRS-CY1JF123J VRS-CY1JF392J VRS-CY1JF561J VRS-CY1JF102J VRS-CY1JF683J VRS-CY1JF123J ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 0 1/16W M-Ox. 0 1/16W M-Ox. 0 1/16W M-Ox. 470 1/8W Carbon 75 1/16W M-Ox. 75 1/16W M-Ox. 75 1/16W M-Ox. 0 1/16W M-Ox. 0 1/16W M-Ox. 0 1/16W M-Ox. 5.6k 1/16W M-Ox. 22k 1/16W M-Ox. 68 1/4W Carbon 470 1/16W M-Ox. 470 1/16W M-Ox. 10k 1/8W Carbon 82 1/16W M-Ox. 82 1/16W M-Ox. 82 1/16W M-Ox. 0 1/16W M-Ox. 100 1/16W M-Ox. 100 1/16W M-Ox. 100 1/16W M-Ox. 470k 1/16W M-Ox. 100 1/16W M-Ox. 82k 1/16W M-Ox. 120k 1/16W M-Ox. 3.9M 1/16W M-Ox. 3.3k 1/16W M-Ox. 150k 1/16W M-Ox. 33k 1/16W M-Ox. 27k 1/16W M-Ox. 100 1/16W M-Ox. 470 1/16W M-Ox. 470 1/16W M-Ox. 1.0k 1/16W M-Ox. 150 1/16W M-Ox. 10 1/16W M-Ox. 100 1/16W M-Ox. 1.5k 1/4W Carbon 1.8k 1/16W M-Ox. 39k 1/16W M-Ox. 27k 1/16W M-Ox. 39k 1/16W M-Ox. 220 1/16W M-Ox. 470 1/16W M-Ox. 390 1/16W M-Ox. 100 1/16W M-Ox. 330 1/4W Carbon 3.3k 1/16W M-Ox. 1.8k 1/8W Carbon 10k 1/16W M-Ox. 15k 1/8W Carbon 68 1/2W M-Ox. 33 2W M-Ox. 100 1/16W M-Ox. 1.2k 1/16W M-Ox. 560 1/16W M-Ox. 1.0k 1/8W Carbon 3.3k 1/16W M-Ox. 27k 1/16W M-Ox. 1.0k 1/16W M-Ox. 180 1/8W Carbon 180 1/8W Carbon 8.2k 1/16W M-Ox. 100 1/16W M-Ox. 390 1/16W M-Ox. 390 1/16W M-Ox. 390 1/16W M-Ox. 68k 1/16W M-Ox. 12k 1/16W M-Ox. 3.9k 1/16W M-Ox. 560 1/16W M-Ox. 1.0k 1/16W M-Ox. 68k 1/16W M-Ox. 12k 1/16W M-Ox. Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. R4913 R4914 R4915 R4916 R4917 R4920 R4921 R4922 R4923 R4930 R4931 R4932 R4933 R4941 R4942 R4950 R4951 R4952 R4953 R4963 Part No. ★ Description Code ★ Part No. Description DUNTKA640WEV1 DUNTKA642WEV1 TERMINAL Unit (Continued) DVD CONTROL Unit VRS-CY1JF392J VRS-CY1JF561J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF683J VRS-CY1JF332J VRS-CY1JF332J VRD-RA2BE222J VRS-CY1JF273J VRS-CY1JF273J VRS-CY1JF123J VRS-CY1JF123J VRD-RA2BE332J VRD-RA2BE332J VRS-CY1JF750J VRS-CY1JF392J VRS-CY1JF392J VRS-CY1JF750J VRD-RA2BE100J J J J J J J J J J J J J J J J J J J J J 3.9k 560 1.0k 1.0k 1.0k 68k 3.3k 3.3k 2.2k 27k 27k 12k 12k 3.3k 3.3k 75 3.9k 3.9k 75 10 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/8W M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. Carbon RBLN-1039CEZZ QTANJ0660CEZZ QTANJ0410AJZZ QTiPM0083CEZZ QPLGN0778GEZZ QPLGN0578GEZZ QPLGZ0860GEZZ QPLGN0278GEZZ QPLGN1278GEZZ VHPGP1F32T/-1 QPLGZ0860GEZZ QPLGZ0860GEZZ QPLGN0961CEZZ QPLGN0661CEZZ QPLGN0861CEZZ QSOCZ0630GEZZ QSOCN2295REZZ QSOCN2295REZZ QSOCZ1040CEZZ RDA4740 PRDAR5072CEFW QCNW-A206WJZZ QCNW-2549PEZZ LHLDW1019PEKZ LHLDW1061PEKZ LHLDW1067PEKZ LX-BZ3100CEFD J R J J J J J J J J J J J J J J J J J J R R R R R J Code DIODES AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA D2951 RH-PX0297GEZZ D2952 RH-PX0297GEZZ D2953 RH-EX0619GEZZ J LED, VCR J LED, DVD J Zener Diode, 6.2V AD AD AA RESISTORS R2951 R2952 R2953 R2954 R2955 R2956 VRD-RA2BE331J VRD-RA2BE331J VRD-RA2BE561J VRD-RA2BE392J VRD-RA2BE822J VRD-RA2BE223J S2951 S2952 S2953 S2954 S2955 QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ J J J J J J 330 330 560 3.9k 8.2k 22k 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W Carbon Carbon Carbon Carbon Carbon Carbon AA AA AA AA AA AA SWITCHES J J J J J Open/Close Play Stop Skip Search (FWD) Skip Search (REV) AB AB AB AB AB MISCELLANEOUS PARTS MISCELLANEOUS PARTS FB2601 J1301 J2602 P51 P1301 P1302 P1401 P2601 P2602 P2604 P3001 P3002 P4603 P4604 P4801 SC1301 SC1302 SC1303 SC1803 Ref. No. P2951 QPLGN0680GEZZ J Plug, 6-pin(DC) QCNW-A085WJZZ R Connecting Cord(DC) Ferrite Bead AC AV Terminal AH Audio Digital Output TerminalAE Tip AB Plug, 7-pin(AR) AC Plug, 5-pin(SC) AB Plug, 8-pin AD Plug, 2-pin(DF) AA Plug, 12-pin(DA) AC Audio Optical Output Terminal AK Plug, 8-pin AD Plug, 8-pin AD Plug, 9-pin(WA) AD Plug, 6-pin(BA) AD Plug, 8-pin(GBN) AC Socket, 6-pin(XC) AC Socket, 22-pin(SB) AD Socket, 22-pin(SA) AD Socket, 10-pin(XB) AD Heat Sink, for IC4740 AC Connecting Cord(P52) AD Connecting Cord(Coaxial) AH Holder AC Holder AD Holder AC Screw AA AB AF DUNTKA643WEV1 VCR CONTROL Unit RESISTORS R2901 R2902 R2903 R2904 R2905 R2906 R2908 R2909 R2910 R2911 VRD-RA2BE563J VRD-RA2BE223J VRD-RA2BE183J VRD-RA2BE472J VRD-RA2BE332J VRD-RA2BE272J VRD-RA2BE223J VRD-RA2BE103J VRD-RA2BE822J VRD-RA2BE103J S2901 S2902 S2903 S2904 S2906 S2907 S2908 S2909 S2910 QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ QSW-K0077GEZZ J J J J J J J J J J 56k 22k 18k 4.7k 3.3k 2.7k 22k 10k 8.2k 10k 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W 1/8W Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon AA AA AA AA AA AA AA AA AA AA SWITCHES J J J J J J J J J REW PLAY FF REC STOP/EJECT CH-UP VOL-DOWN VOL-UP CH-DOWN AB AB AB AB AB AB AB AB AB MISCELLANEOUS PARTS P2901 QPLGN0342CEZZ J Plug, 3-pin(OO) QCNW-5030PEN3 R Connecting Cord(OO) 168 AA AD 27DV-S100 27DV-CS10 Ref. No. ★ Part No. Description Code Ref. No. Description DUNTKA669WEV1 DUNTKA680WEV1 FRONT AV Unit TERMINAL SUB Unit RESISTORS R3901 VRD-RA2BE750J R3971 VRD-RM2HD471J R3972 VRD-RM2HD471J J 75 1/8W J 470 1/2W J 470 1/2W QJAKG0082CEZZ QJAKJ0101SEZZ QPLGN0778GEZZ QPLGN0578GEZZ R J J J Code INTEGRATED CIRCUITS Carbon Carbon Carbon AA AA AA MISCELLANEOUS PARTS J3901 J3971 P3901 P3971 ★ Part No. AV-2 INPUT Terminal Headphone Jack Plug, 7-pin(AR) Plug, 5-pin(ZA) AG AE AC AB IC1401 IC1402 IC1403 IC3001 IC3201 VHiTC90A45F-1 VHiKA78L05B-1 VHiMM1502XN-1~ VHiCXA2074Q-1 VHiAN5285K/-1 Q1401 Q1402 Q1403 Q1404 Q1405 Q1406 VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E VS2SC1623L51E L1401 L1403 L1404 L1407 L1412 L1413 VP-XF100K0000 VP-XF330K0000 VP-XF330K0000 VP-XF1R0K0000 VP-XF1R0K0000 VP-XF330K0000 J J R J J TC90A45F KA78L05BP MM1502XNRE CXA2074Q AN5285K AM AE AE AY AP TRANSISTORS J J J J J J 2SC1623L5 2SC1623L5 2SC1623L5 2SC1623L5 2SC1623L5 2SC1623L5 AB AB AB AB AB AB COILS J J J J J J Peaking 10µH Peaking 33µH Peaking 33µH Peaking 1µH Peaking 1µH Peaking 33µH AB AB AB AB AB AB CAPACITORS C1415 C1416 C1417 C1418 C1419 C1420 C1421 C1422 C1430 C1432 C1433 C1435 C1436 C1439 C1440 C1441 C1442 C1443 C1446 C1447 C1450 C1451 C1452 C1453 C1454 C1456 C1457 C1459 C1460 C1461 C1469 C1470 C1473 C3001 C3002 C3003 C3004 C3005 C3006 C3007 C3008 C3009 C3010 C3011 C3012 C3013 169 [EL.··· Electrolytic] VCCCCY1HH220J J 22p 50V VCEA0A1CW107M J 100 16V VCCCCY1HH120J J 12p 50V VCCCCY1HH120J J 12p 50V VCCCCY1HH100D J 10p 50V VCCCCY1HH120J J 12p 50V VCKYCY1CB104K J 0.1 16V VCEA0A1EW476M J 47 25V VCKYCY1HF103Z J 0.01 50V VCKYCY1CB104K J 0.1 16V VCKYCY1CB104K J 0.1 16V VCKYCY1HF103Z J 0.01 50V VCKYCY1CB104K J 0.1 16V VCE9GA1CW106M J 10 16V VCEA0A1CW106M J 10 16V VCKYCY1HF103Z J 0.01 50V VCEA0A1HW105M J 1.0 50V VCKYCY1EB103K J 0.01 25V VCCCCY1HH181J J 180p 50V VCKYCY1EB103K J 0.01 25V VCKYCY1CB104K J 0.1 16V VCEA0A1CW107M J 100 16V VCKYCY1CB104K J 0.1 16V VCKYCY1EB103K J 0.01 25V VCKYCY1EB103K J 0.01 25V VCKYCY1CB104K J 0.1 16V RC-EZ0459CEZZ J 10 10V VCCCCY1HH220J J 22p 50V VCCCCY1HH121J J 120p 50V VCKYPA1HF103Z J 0.01 50V VCCCCY1HH120J J 12p 50V VCCCCY1HH100D J 10p 50V VCCCCY1HH100D J 10p 50V VCE9GA1HW475M J 4.7 50V VCKYCY1HB562K J 5600p 50V VCQYTA1HM123K J 0.012 50V VCEA0A1HW105M J 1.0 50V VCE9GA1HW475M J 4.7 50V VCEA0A1CW106M J 10 16V VCEA0A1HW475M J 4.7 50V VCKYCY1HF103Z J 0.01 50V VCEA0A1CW227M J 220 16V VCE9GA1HW475M J 4.7 50V VCEA0A1HW475M J 4.7 50V VCE9GA1HW475M J 4.7 50V VCKYCY1HB272K J 2700p 50V Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. (N.P) EL. Ceramic EL. Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. (N.P) Ceramic Mylar EL. EL. (N.P) EL. EL. Ceramic EL. EL. (N.P) EL. EL. (N.P) Ceramic AA AC AA AA AA AA AB AB AA AB AB AA AB AB AB AA AB AA AA AA AB AC AB AA AA AB AE AA AA AA AA AA AA AB AA AA AB AB AB AB AA AC AB AB AB AA 27DV-S100 27DV-CS10 Ref. No. ★ Part No. Description Code Ref. No. ★ Part No. Description DUNTKA680WEV1 DUNTKA686WEV1 TERMINAL SUB Unit (Continued) CRT Unit C3014 C3015 C3016 C3017 C3018 C3029 C3030 C3031 C3032 C3181 C3183 C3201 C3202 C3203 C3204 C3205 C3206 C3207 C3208 C3209 VCQYTA1HM473J VCSATA1CE335K VCE9GA1HW475M VCSATA1CE106K VCEA0A1HW105M VCKYCY1HB682K VCKYCY1HB682K VCKYCY1CB473K VCKYCY1CB473K VCEA0A1HW225M VCEA0A1HW225M VCE9GA1HW475M VCE9GA1HW475M VCEA0A1HW475M VCEA0A1CW106M VCEA0A1CW106M VCKYCY1HF103Z VCE9GA1HW475M VCE9GA1HW475M VCEA0A1CW106M J J J J J J J J J J J J J J J J J J J J 0.047 3.3 4.7 10 1.0 6800p 6800p 0.047 0.047 2.2 2.2 4.7 4.7 4.7 10 10 0.01 4.7 4.7 10 50V 16V 50V 16V 50V 50V 50V 16V 16V 50V 50V 50V 50V 50V 16V 16V 50V 50V 50V 16V R1403 R1404 R1407 R1408 R1409 R1411 R1412 R1413 R1414 R1415 R1416 R1417 R1418 R1431 R1432 R1434 R1446 R1447 R1450 R1459 R3001 R3002 R3003 R3004 R3006 R3007 R3008 R3010 R3011 R3012 R3013 R3014 R3015 R3016 R3017 R3018 R3104 R3201 R3202 R3203 [M-Ox.··· Metal Oxide] VRS-CY1JF821J J 820 1/16W VRS-CY1JF152J J 1.5k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF471J J 470 1/16W VRS-CY1JF821J J 820 1/16W VRS-CY1JF222J J 2.2k 1/16W VRS-CY1JF152J J 1.5k 1/16W VRS-CY1JF561J J 560 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF471J J 470 1/16W VRS-CY1JF821J J 820 1/16W VRS-CY1JF122J J 1.2k 1/16W VRS-CY1JF332J J 3.3k 1/16W VRS-CY1JF000J J 00 1/16W VRS-CY1JF471J J 470 1/16W VRS-CY1JF000J J 00 1/16W VRS-CY1JF101J J 100 1/16W VRS-CY1JF153J J 15k 1/16W VRS-CY1JF273J J 27k 1/16W VRS-CY1JF821J J 820 1/16W VRD-RA2BE221J J 220 1/8W VRD-RA2BE221J J 220 1/8W VRS-CY1JF105J J 1.0M 1/16W VRS-CY1JF104J J 100k 1/16W VRS-CY1JF623J J 62k 1/16W VRS-CY1JF332J J 3.3k 1/16W VRS-CY1JF302J J 3.0k 1/16W VRS-CY1JF392J J 3.9k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF101J J 100 1/16W VRS-CY1JF101J J 100 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRD-RA2BE101J J 100 1/8W VRD-RA2BE101J J 100 1/8W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF225J J 2.2M 1/16W VRS-CY1JF682J J 6.8k 1/16W VRS-CY1JF101J J 100 1/16W FB1401 FB1402 SC1401 SC3001 SC3002 RBLN-0013GEZZ RBLN-0013GEZZ QSOCZ0860GEZZ QSOCZ0860GEZZ QSOCZ0860GEZZ Mylar Tantalum EL. (N.P) Tantalum EL. Ceramic Ceramic Ceramic Ceramic EL. EL. EL. (N.P) EL. (N.P) EL. EL. EL. Ceramic EL. (N.P) EL. (N.P) EL. INTEGRATED CIRCUIT AA AC AB AD AB AA AA AA AA AB AB AB AB AB AB AB AA AB AB AB IC8850 VHiTDA6103Q-1 Ferrite Bead Ferrite Bead Socket, 8-pin Socket, 8-pin Socket, 8-pin AL TRANSISTORS J 2SC3198-Y J 2SA1266-Y J 2SA1964E AA AA AF J 2SC5248E AE J 2SA1266-Y J 2SC3198-Y AA AA DIODES D1502 D1503 D1506 D1507 D1510 D1515 D1518 D8850 D8851 D8852 D8853 D8854 D8855 D8856 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AA AA AA AA VHD1SS119//-1 VHD1SS119//-1 RH-DX0487CEZZ RH-DX0487CEZZ VHD1SS119//-1 RH-EX0400GEZZ RH-EX0400GEZZ RH-DX0220CEZZ RH-DX0220CEZZ RH-DX0220CEZZ RH-EX0647GEZZ VHD1SS119//-1 VHD1SS119//-1 RH-EX0718GEZZ J J J J J J J J J J J J J J Diode Diode Diode Diode Diode Zener Diode, 11V Zener Diode, 11V Diode Diode Diode Zener Diode, 15V Diode Diode Zener Diode, 3.0V AB AB AC AC AB AA AA AB AB AB AA AB AB AB CAPACITORS C1501 C1506 C1508 C1509 C1510 C1511 C1515 C1516 C1517 C1518 C1519 C8850 C8851 C8852 C8853 C8854 C8855 C8856 [EL.··· Electrolytic] VCEA0A1CW476M J 47 16V VCKYPA1HF103Z J 0.01 50V VCKYPA2HB472K J 4700p 500V VCKYPA2HB472K J 4700p 500V VCKYPA1HF103Z J 0.01 50V VCKYPA1HF103Z J 0.01 50V VCEA0A1CW476M J 47 16V VCEA0A1CW476M J 47 16V VCEA0A2AW106M J 10 100V VCCSPA2HL560K J 56p 500V VCEA4A2CN106M J 10 160V RC-FZ0373CEZZ J 0.082 250V RC-KZ018JCEZZ J 0.01 3kV VCEA0A1CW227M J 220 16V VCFYFA1HA224J J 0.22 50V VCEA0A1CW227M J 220 16V VCEA0A2EW106M J 10 250V VCEA0A1CW476M J 47 16V EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. EL. Ceramic EL. Polypro Ceramic EL. Mylar EL. EL. EL. AB AA AB AB AA AA AB AB AC AA AC AC AC AC AB AC AD AB RESISTORS R1511 R1513 R1514 R1515 R1516 R1517 R1518 R1519 R1520 R1521 R1525 R1526 R1527 R1528 å R1529 R1530 R8850 å MISCELLANEOUS PARTS J J J J J J TDA6103Q/N3 Q1504 VS2SC3198-Y-1 Q1505 VS2SA1266-Y-1 Q1506 VS2SA1964E/-1 or VS2SA1930++-1 Q1507 VS2SC5248E/-1 or VS2SC5171++-1 Q8850 VS2SA1266-Y-1 Q8851 VS2SC3198-Y-1 RESISTORS M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. Code AB AB AD AD AD 170 [M-Ox.··· Metal Oxide] VRD-RA2BE101J J 100 1/8W VRS-VV3DB471J J 470 2W VRD-RA2BE100J J 10 1/8W VRD-RA2BE820J J 82 1/8W VRD-RA2BE820J J 82 1/8W VRD-RA2BE122J J 1.2k 1/8W VRD-RA2BE683J J 68k 1/8W VRD-RA2BE123J J 12k 1/8W VRD-RA2BE683J J 68k 1/8W VRD-RA2BE122J J 1.2k 1/8W VRD-RA2EE560J J 56 1/4W VRD-RA2EE560J J 56 1/4W VRD-RA2EE2R7J J 2.7 1/4W VRD-RA2EE2R7J J 2.7 1/4W VRS-VV3DB221J J 220 2W VRD-RA2BE222J J 2.2k 1/8W VRS-SV2HC152J J 1.5k 1/2W Carbon M-Ox. Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon M-Ox. Carbon M-Ox. AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description DUNTKA686WEV1 DUNTK6054TE6H CRT Unit (Continued) DVD MAIN Unit R8851 R8852 R8853 R8854 R8855 R8856 R8857 R8858 R8862 R8863 R8864 R8867 R8868 R8869 R8870 R8871 R8872 R8873 R8874 R8875 R8876 R8890 VRS-SV2HC152J VRS-SV2HC152J VRS-SV2HC272J VRS-SV2HC272J VRS-SV2HC272J VRD-RM2HD224J VRD-RM2HD224J VRD-RM2HD224J VRC-MA2HG152K VRC-MA2HG152K VRC-MA2HG152K VRD-RA2BE332J VRD-RA2BE222J VRD-RA2BE822J VRD-RA2BE223J VRD-RA2BE223J VRD-RA2EE122J VRD-RM2HD224J VRD-RM2HD184J VRD-RM2HD184J VRD-RM2HD184J VRD-RA2BE100J FB8850 P8854 P8856 P8858 P8860 P8861 SC850 RDA8850 RDA1506 RDA1507 RBLN-0091GEZZ QPLGN0741CEZZ QTiPM0083CEZZ QTiPM0083CEZZ QPLGN0841CEZZ QPLGN0241CEZZ QSOCV0936CEZZ PRDAR0248PEFW PRDAR0083PEFW PRDAR0083PEFW J J J J J J J J J J J J J J J J J J J J J J 1.5k 1.5k 2.7k 2.7k 2.7k 220k 220k 220k 1.5k 1.5k 1.5k 3.3k 2.2k 8.2k 22k 22k 1.2k 220k 180k 180k 180k 10 1/2W 1/2W 1/2W 1/2W 1/2W 1/2W 1/2W 1/2W 1/2W 1/2W 1/2W 1/8W 1/8W 1/8W 1/8W 1/8W 1/4W 1/2W 1/2W 1/2W 1/2W 1/8W M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon Carbon Solid Solid Solid Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon Carbon INTEGRATED CIRCUITS AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA Ferrite Bead Plug, 7-pin(N) Tip(K857) Tip(CE) Plug, 8-pin(GBN) Plug, 2-pin(PU) CRT Socket Heat Sink, for IC850 Heat Sink, for Q1506 Heat Sink, for Q1507 IC301 IC501 IC502 IC503 IC504 IC507 IC508 IC601 IC602 IC603 IC701 IC702 IC705 IC7701 IC7702 VHiTA1323F+-1Q RH-iX1689GEZZ RH-iX1765GEZZ VHiPST600iM-1 RH-iX1687GEZZ VHiBR93L66F-1 RH-iX1761GEZZQ RH-iX1720GEZZQ RH-iX3455CEZZ RH-iX3455CEZZ VHiTC94A03F-1Q RH-iX3420CEZZ VHiNJM12904-1~ VHiBA5984FP-1 VHiTC4W53F/-1 R J R J J J V R J J R J V J J TA1323F LH28F800BVE MSM51V4265E IC-PST600LMT HB6412320VTE25 BR93LC66F-E2 SLAC250F3A ZR36732 NT56V1616A0T-7 NT56V1616A0T-7 TC94A03F MSM5416258B-28 NJM12904M BA5984FP-E2 TC4W53F Q202 Q203 Q205 Q301 Q302 Q303 Q307 Q502 Q503 Q701 Q702 VS2SA1576A+-1 VS2SA1576A+-1 VS2SA1576A+-1 VS2SA1576A+-1 VS2SA1298Y/-1 VS2SA1298Y/-1 VSDTC144EUA-1 VS2SA1298Y/-1 VSDTC144EUA-1 VSDTC144EUA-1 VSDTC144EUA-1 D301 D501 VHDDAP222//-1 VHDDAN222//-1 X601 RCRSC0039GEZZ~ A Crystal 27MHz FL501 FL701 L601 L602 RFiLC0207GEZZ RCRMC0001GEZZ~ VP-NM470K2R0N VP-NM470K2R0N AV BB AX AE BD AH AW BG AZ AZ BC AT AE AR AE TRANSISTORS MISCELLANEOUS PARTS J J J J J J J R R R Code AB AC AB AB AB AA AM AF AD AD J J J J J J J J J J J 2SA1576A 2SA1576A 2SA1576A 2SA1576A 2SA1298Y 2SA1298Y DTC144EUA 2SA1298Y DTC144EUA DTC144EUA DTC144EUA AB AB AB AB AB AB AB AB AB AB AB DIODES J Diode J Diode AA AA PACKAGED CIRCUIT AH FILTER AND COILS J J J J Filter 20MHz Filter 20.5792MHz Peaking 47µH Peaking 47µH AD AD AB AB CAPACITORS C204 C205 C206 C207 C208 C209 C210 C211 C212 C213 C214 C302 C303 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 171 [EL.··· Electrolytic] VCKYCY1CB104K J 0.1 16V VCEAPF0JW476M J 47 6.3V VCKYCY1HB103K J 0.01 50V VCKYCY1HB103K J 0.01 50V VCKYCY1HB103K J 0.01 50V VCKYCY1HB103K J 0.01 50V VCKYCY1HB103K J 0.01 50V VCKYCY1HB103K J 0.01 50V RC-EZ0475GEZZ J 220 6.3V RC-EZ0475GEZZ J 220 6.3V RC-EZ0475GEZZ J 220 6.3V VCKYCY0JF105Z J 1.0 6.3V VCKYCY0JF105Z J 1.0 6.3V VCKYCY1HB103K J 0.01 50V VCEAPF0JW107M J 100 6.3V VCEAPF0JW476M J 47 6.3V VCKYCY1HB103K J 0.01 50V VCEAPF0JW476M J 47 6.3V VCEAPF1HW225M J 2.2 50V VCKYCY1HB103K J 0.01 50V VCKYCY1HB102K J 1000p 50V VCKYCY1HB102K J 1000p 50V VCEAPF0JW476M J 47 6.3V VCKYCY1HB102K J 1000p 50V VCKYCY1CB104K J 0.1 16V VCKYCY1HB102K J 1000p 50V Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. EL. Ceramic Ceramic Ceramic EL. EL. Ceramic EL. EL. Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic AB AB AA AA AA AA AA AA AD AD AD AB AB AA AC AB AA AB AB AA AA AA AB AA AB AA 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code DUNTK6054TE6H DVD MAIN Unit (Continued) C319 C320 C321 C322 C323 C324 C325 C326 C328 C332 C501 C502 C503 C504 C506 C508 C510 C511 C512 C515 C516 C517 C519 C520 C521 C522 C523 C524 C525 C526 C527 C528 C529 C602 C604 C605 C606 C609 C610 C613 C614 C617 C618 C619 C620 C621 C623 C624 C625 C626 C627 C628 C629 C630 C631 C632 C633 C635 C640 C644 C646 C701 C702 C703 C704 C705 C706 C707 C708 C709 C710 C711 VCEAPF0JW476M VCKYCY1CB104K VCEAPF0JW476M VCKYCY1HB103K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1HB472K VCKYCY1HB472K VCKYCY1CB104K VCKYCY1HB102K VCKYCY1CB104K VCEAPF0JW107M VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY0JF105Z VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCEAPF0JW476M VCKYCY1HB103K VCKYCY1HB472K VCKYCY1HB103K VCEAPF0JW476M VCKYCY1HB103K VCKYCY1HB103K VCKYCY1HB103K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K RC-EZ0475GEZZ VCKYCY1CB104K VCKYCY1CB104K RC-EZ0475GEZZ VCKYCY1CB104K VCKYCY1CB104K VCEAPF0JW476M VCKYCY1CB104K VCCCCY1HH100D VCCCCY1HH100D VCEAPF0JW476M RC-EZ0475GEZZ VCKYCY1CB104K VCEAPF0JW476M VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCEAPF0JW107M VCKYCY1HB103K VCCCCY1HH820J VCCCCY1HH820J VCKYCY1HB103K VCCCCY1HH221J VCCCCY1HH221J VCEAPF0JW476M VCKYCY1CB104K VCCCCY1HH221J VCEAPF1CW106M VCKYCY1CB104K J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 47 0.1 47 0.01 0.1 0.1 4700p 4700p 0.1 1000p 0.1 100 0.1 0.1 0.1 0.1 0.1 0.1 1.0 0.01 0.01 0.01 0.01 0.01 0.01 47 0.01 4700p 0.01 47 0.01 0.01 0.01 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 220 0.1 0.1 220 0.1 0.1 47 0.1 10p 10p 47 220 0.1 47 0.1 0.1 0.1 0.1 0.1 100 0.01 82p 82p 0.01 220p 220p 47 0.1 220p 10 0.1 6.3V 16V 6.3V 50V 16V 16V 50V 50V 16V 50V 16V 6.3V 16V 16V 16V 16V 16V 16V 6.3V 50V 50V 50V 50V 50V 50V 6.3V 50V 50V 50V 6.3V 50V 50V 50V 16V 16V 16V 16V 16V 16V 16V 16V 6.3V 16V 16V 6.3V 16V 16V 6.3V 16V 50V 50V 6.3V 6.3V 16V 6.3V 16V 16V 16V 16V 16V 6.3V 50V 50V 50V 50V 50V 50V 6.3V 16V 50V 16V 16V EL. Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic EL. Ceramic Ceramic EL. Ceramic Ceramic Ceramic EL. EL. Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic EL. Ceramic AB AB AB AA AB AB AA AA AB AA AB AC AB AB AB AB AB AB AB AA AA AA AA AA AA AB AA AA AA AB AA AA AA AB AB AB AB AB AB AB AB AD AB AB AD AB AB AB AB AA AA AB AD AB AB AB AB AB AB AB AC AA AA AA AA AA AA AB AB AA AB AB Ref. No. ★ Part No. J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description C712 C713 C714 C715 C716 C717 C718 C720 C721 C722 C723 C725 C726 C727 C728 C729 C730 C731 C732 C733 C734 C735 C741 C742 C744 C746 C747 C748 C749 C750 C751 C752 C753 C756 C757 C758 C759 C7702 C7703 C7704 C7705 C7706 VCKYCY1CB104K VCKYCY1HB103K VCEAPF0JW476M VCKYCY1CB104K VCCCCY1HH221J VCKYCY1HB472K VCKYCY1HB153K VCKYCY1HB682K VCKYCY1HB153K VCKYCY1HB153K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCCCCY1HH221J VCKYCY1HB472K VCKYCY1CB104K VCKYCY1HB102K VCKYCY1CB104K VCKYCY1CB104K VCCCCY1HH561J VCKYCY1HB103K VCKYCY1HB103K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1HB102K VCKYCY1HB153K VCKYCY1CB104K VCKYCY1HB102K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1CB104K VCKYCY1HB103K VCEAPF1CW106M VCCCCY1HH101J VCCCCY1HH221J VCKYCY1CB104K 0.1 0.01 47 0.1 220p 4700p 0.015 6800p 0.015 0.015 0.1 0.1 0.1 0.1 220p 4700p 0.1 1000p 0.1 0.1 560p 0.01 0.01 0.1 0.1 0.1 0.1 1000p 0.015 0.1 1000p 0.1 0.1 0.1 0.1 0.1 0.1 0.01 10 100p 220p 0.1 16V 50V 6.3V 16V 50V 50V 50V 50V 50V 50V 16V 16V 16V 16V 50V 50V 16V 50V 16V 16V 50V 50V 50V 16V 16V 16V 16V 50V 50V 16V 50V 16V 16V 16V 16V 16V 16V 50V 16V 50V 50V 16V R225 R226 R227 R303 R310 R311 R314 R315 R316 R317 R318 R319 R320 R325 R326 R327 R328 R343 R344 R345 R501 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 [M-Ox.··· Metal Oxide] VRS-CY1JF681J J 680 1/16W VRS-CY1JF681J J 680 1/16W VRS-CY1JF681J J 680 1/16W VRS-CY1JF222J J 2.2k 1/16W VRS-CY1JF472J J 4.7k 1/16W VRS-CY1JF335J J 3.3M 1/16W VRS-TW2ED330J J 33 1/4W VRS-CY1JF471J J 470 1/16W VRS-CY1JF335J J 3.3M 1/16W VRS-CY1JF103J J 10k 1/16W VRS-TW2ED470J J 47 1/4W VRS-TW2ED470J J 47 1/4W VRS-CY1JF471J J 470 1/16W VRS-CY1JF820J J 82 1/16W VRS-CY1JF100J J 10 1/16W VRS-CY1JF820J J 82 1/16W VRS-CY1JF100J J 10 1/16W VRS-CY1JF000J J 0 1/16W VRS-CY1JF000J J 0 1/16W VRS-CY1JF000J J 0 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF332J J 3.3k 1/16W VRS-CY1JF332J J 3.3k 1/16W VRS-CY1JF332J J 3.3k 1/16W VRS-CY1JF100J J 10 1/16W VRS-CY1JF100J J 10 1/16W VRS-CY1JF100J J 10 1/16W VRS-CY1JF103J J 10k 1/16W Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Code AB AA AB AB AA AA AA AA AA AA AB AB AB AB AA AA AB AA AB AB AB AA AA AB AB AB AB AA AA AB AA AB AB AB AB AB AB AA AB AA AA AB RESISTORS 172 M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code R715 R716 R717 R718 R719 R720 R721 R724 R725 R726 R727 R728 R729 R730 R731 R732 R734 R735 R736 R737 R738 R739 R740 R741 R742 R743 R744 R745 R746 R747 R748 R749 R750 R751 R752 R753 R754 R755 R756 R757 R758 R759 R760 R761 R762 R763 R764 R765 R768 R769 R780 R801 R802 R803 R804 R805 R806 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R823 R824 R826 R828 R7717 R7721 R7722 DUNTK6054TE6H DVD MAIN Unit (Continued) R513 R514 R515 R516 R517 R518 R519 R520 R522 R523 R524 R525 R528 R529 R530 R531 R532 R533 R534 R535 R536 R537 R538 R540 R541 R543 R544 R545 R552 R555 R556 R557 R558 R560 R561 R564 R565 R566 R568 R569 R570 R571 R601 R602 R603 R604 R607 R608 R610 R612 R613 R615 R616 R617 R620 R621 R622 R701 R702 R703 R704 R705 R706 R707 R708 R709 R710 R711 R712 R713 R714 VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF154J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF100J VRS-CY1JF473J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF102J VRS-CY1JF222J VRS-CY1JF472J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF562J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF100J VRS-CY1JF103J VRS-CY1JF560F VRS-CY1JF391F VRS-CY1JF560F VRS-CY1JF560F VRS-CY1JF560F VRS-CY1JF684J VRS-CY1JF101J VRS-CY1JF221J VRS-CY1JF391J VRS-CY1JF221J VRS-CY1JF221J VRS-CY1JF221J VRS-CY1JF180J VRS-CY1JF223J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF223J VRS-CY1JF682J VRS-CY1JF222J VRS-CY1JF000J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF123J VRS-CY1JF822J VRS-CY1JF000J VRS-CY1JF473J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 4.7k 1.0k 150k 10k 1.0k 1.0k 1.0k 10k 10 47k 10k 10k 10k 4.7k 10k 4.7k 10k 10k 10k 10k 0 10k 10k 4.7k 1.0k 10k 4.7k 1.0k 0 0 1.0k 2.2k 4.7k 10k 10k 5.6k 10k 10k 100 100 0 0 10 10k 56 390 56 56 56 680k 100 220 390 220 220 220 18 22k 10k 10k 22k 6.8k 2.2k 0 12k 12k 12k 12k 8.2k 0 47k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Ref. No. AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 173 Part No. ★ VRS-CY1JF154J VRS-CY1JF181J VRS-CY1JF183J VRS-CY1JF151J VRS-CY1JF151J VRS-CY1JF151J VRS-CY1JF222J VRS-CY1JF104J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF331J VRS-CY1JF331J VRS-CY1JF393J VRS-CY1JF273J VRS-CY1JF273J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF333F VRS-CY1JF472J VRS-CY1JF473F VRS-CY1JF000J VRS-CY1JF333F VRS-CY1JF152J VRS-CY1JF473F VRS-CY1JF103J VRS-CY1JF104J VRS-CY1JF000J VRS-CY1JF333J VRS-CY1JF000J VRS-CY1JF154J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF334J VRS-CY1JF105J VRS-CY1JF471J VRS-CY1JF100J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF474J VRS-CY1JF102J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ RBLN-0076TAZZ VRS-CY1JF472J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF100J VRS-CY1JF103J VRS-CY1JF101J VRS-CY1JF152J VRS-CY1JF102J VRS-CY1JF223J VRS-CY1JF223J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 150k 1/16W 180 1/16W 18k 1/16W 150 1/16W 150 1/16W 150 1/16W 2.2k 1/16W 100k 1/16W 1.0k 1/16W 0 1/16W 330 1/16W 330 1/16W 39k 1/16W 27k 1/16W 27k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 0 1/16W 33k 1/16W 4.7k 1/16W 47k 1/16W 0 1/16W 33k 1/16W 1.5k 1/16W 47k 1/16W 10k 1/16W 100k 1/16W 0 1/16W 33k 1/16W 0 1/16W 150k 1/16W 0 1/16W 0 1/16W 330k 1/16W 1M 1/16W 470 1/16W 10 1/16W 10k 1/16W 10k 1/16W 470k 1/16W 1.0k 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead 4.7k 1/16W 10 1/16W 10 1/16W 10 1/16W 10k 1/16W 100 1/16W 1.5k 1/16W 1.0k 1/16W 22k 1/16W 22k 1/16W M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AC AC AC AC AC AC AC AC AC AC AC AC AC AA AA AA AA AA AA AA AA AA AA 27DV-S100 27DV-CS10 Ref. No. R7724 R7725 R7726 R7729 R7730 R7732 R7734 R7736 Part No. ★ Description Code ★ Part No. Description DUNTK6054TE6H DUNTK6081TEV1 DVD MAIN Unit (Continued) DVD SUB Unit VRS-CY1JF333J VRS-CY1JF223J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF473J VRS-CY1JF102J VRS-CY1JF822J VRS-CY1JF102J J J J J J J J J 33k 22k 10k 10k 47k 1.0k 8.2k 1.0k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. RBLN-0077TAZZ J RBLN-0061TAZZ J RBLN-0052TAZZ J RBLN-0061TAZZ J RBLN-0061TAZZ J RBLN-0077TAZZ J RBLN-0077TAZZ J RBLN-0077TAZZ J RBLN-0077TAZZ J RBLN-0077TAZZ J RBLN-0077TAZZ J RBLN-0077TAZZ J RBLN-0077TAZZ J RBLN-0076TAZZ J RBLN-0077TAZZ J QPLGN0964TAZZ J QSOCN2336TAZZ~ V QPLGN0464TAZZ J QPLGN0664TAZZ J QPLGN0564TAZZ J QPLGN0364TAZZ J QSOCN2936TAZZ J QSOCN0936TAZZ J Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Plug, 9-pin(CC) Socket, 23-pin Plug, 4-pin Plug, 6-pin(AA) Plug, 5-pin(AC) Plug, 3-pin Socket, 29-pin(CB) Socket, 9-pin(CA) Code INTEGRATED CIRCUITS AA AA AA AA AA AA AA AA IC1001 IC1101 IC1102 IC1201 IC1202 VHiMM1540AF-1 VHiPCM1737E-1 VHiNJM4560M-1 RH-iXA023WJZZ VHiPST600H/-1 Q1101 Q1102 Q1103 Q1104 Q1105 Q1106 Q1107 Q1108 Q1109 Q1110 Q1111 Q1201 Q1202 Q1203 Q1204 Q1205 Q1206 Q1207 Q1208 Q1209 Q1210 Q1211 Q1212 Q1213 VS2SD1306-E-1 VS2SD1306-E-1 VS2SA1530ARS1 VSKRC102S//-1 VSKRC103S//-1 VSKRC103S//-1 VSKRC103S//-1 VSKRC102S//-1 VSKRA102S//-1 VSKRC102S//-1 VSKRA102S//-1 VSKRC103S//-1 VSKRC103S//-1 VSKRC102S//-1 VSKRC102S//-1 VSKRA102S//-1 VSKRC102S//-1 VSKRA102S//-1 VSKRA102S//-1 VSKRA102S//-1 VSKRA102S//-1 VSKRC102S//-1 VSKRC102S//-1 VSKRA102S//-1 D1001 D1002 D1101 D1102 D1104 D1202 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 R R J V J MM1540AF PCM1737E/2K NJM4560M M38513M4-C70FP IC-PST600H-2 AN AS AG AU AE TRANSISTORS MISCELLANEOUS PARTS FB301 FB601 FB602 FB603 FB605 FB806 FB807 FB808 FB809 FB810 FB813 FB814 FB815 FB816 FB817 CN201 CN301 CN302 CN701 CN702 CN703 CN801 CN802 Ref. No. AB AD AC AD AD AB AB AB AB AB AB AB AB AC AB AF AF AC AD AC AC AF AD J J J J J J J J J J J J J J J J J J J J J J J J 2SD1306-E 2SD1306-E 2SA1530ARS KRC102S KRC103S KRC103S KRC103S KRC102S KRA102S KRC102S KRA102S KRC103S KRC103S KRC102S KRC102S KRA102S KRC102S KRA102S KRA102S KRA102S KRA102S KRC102S KRC102S KRA102S AC AC AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA DIODES J J J J J J Diode Diode Diode Diode Diode Diode AB AB AB AB AB AB FILTER AND COIL FL1201 RFiLC0121GEZZ L1003 VP-MK101K0000 J Filter 8MHz J Peaking 100µH AD AB CAPACITORS C1001 C1002 C1003 C1004 C1005 C1012 C1013 C1017 C1018 C1019 C1101 C1102 C1103 C1104 C1105 C1106 C1107 C1108 C1109 C1110 C1111 C1112 C1113 174 [EL.··· Electrolytic] VCEA9M1CW107M J 100 16V VCKYCY1EB103K J 0.01 25V VCKYCY1CB104K J 0.1 16V VCKYCY1EB103K J 0.01 25V VCKYCY1CB104K J 0.1 16V VCKYCY1HF103Z J 0.01 50V VCEA9M0JW476M J 47 6.3V VCEA9M0JW227M J 220 6.3V VCKYD41CY103N J 0.01 16V VCEA9M0JW227M J 220 6.3V VCEA9M1CW106M J 10 16V VCEA9M0JW227M J 220 6.3V VCKYCY1CB104K J 0.1 16V VCKYCY1HB102K J 1000p 50V VCKYCY1CB104K J 0.1 16V VCEA9M1CW106M J 10 16V VCKYCY1HB102K J 1000p 50V VCEA9M0JW227M J 220 6.3V VCEA9M1CW106M J 10 16V VCEA9M1CW226M J 22 16V VCKYCY1HB222K J 2200p 50V VCKYCY1HB222K J 2200p 50V VCEA9M1CW106M J 10 16V EL. Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. Ceramic EL. EL. EL. Ceramic Ceramic Ceramic EL. Ceramic EL. EL. EL. Ceramic Ceramic EL. AB AA AB AA AB AA AB AB AA AB AB AB AB AA AB AB AA AB AB AB AA AA AB 27DV-S100 27DV-CS10 Ref. No. ★ Part No. Description Code DUNTK6081TEV1 DVD SUB Unit (Continued) C1114 C1115 C1116 C1117 C1118 C1120 C1121 C1201 C1202 C1204 C1205 C1206 C1208 C1209 C1210 C1211 C1212 C1213 C1214 C1215 C1216 C1217 C1218 C1220 C1221 C1229 VCEA9M1CW106M VCEA9M1CW226M VCEA9M0JW227M VCKYCY1HB222K VCCCCY1HH680J VCEA9M1CW106M VCKYD41HB102K VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCEA9M1HW105M VCEA9M0JW476M VCCCCY1HH680J VCCCCY1HH680J VCCCCY1HH680J VCEA9M1AW107M VCCCCY1HH680J VCKYCY1HF103Z VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K RC-EZ0459CEZZ RC-EZ0459CEZZ VCCCCY1HH680J J J J J J J J J J J J J J J J V J J J J J J J J J J 10 22 220 2200p 68p 10 1000p 0.01 0.01 0.01 1.0 47 68p 68p 68p 100 68p 0.01 1000p 1000p 1000p 1000p 1000p 10 10 68p 16V 16V 6.3V 50V 50V 16V 50V 50V 50V 50V 50V 6.3V 50V 50V 50V 10V 50V 50V 50V 50V 50V 50V 50V 10V 10V 50V R1002 R1011 R1012 R1013 R1015 R1016 R1017 R1018 R1102 R1104 R1105 R1106 R1107 R1108 R1109 R1110 R1111 R1112 R1113 R1114 R1115 R1116 R1117 R1118 R1120 R1121 R1122 R1123 R1124 R1126 R1128 R1201 R1202 R1203 R1204 R1205 R1206 R1207 R1208 R1209 R1210 R1211 [M-Ox.··· Metal Oxide] VRS-CY1JF152J J 1.5k 1/16W VRD-RA2BE750J J 75 1/8W VRD-RA2BE750J J 75 1/8W VRD-RA2BE750J J 75 1/8W VRS-CY1JF000J J 0 1/16W VRS-CY1JF000J J 0 1/16W VRD-RA2BE472J J 4.7k 1/8W VRS-CY1JF562J J 5.6k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRD-RA2BE470J J 47 1/8W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF153J J 15k 1/16W VRS-CY1JF474J J 470k 1/16W VRS-CY1JF153J J 15k 1/16W VRS-CY1JF681J J 680 1/16W VRS-CY1JF682J J 6.8k 1/16W VRS-CY1JF152J J 1.5k 1/16W VRS-CY1JF682J J 6.8k 1/16W VRS-CY1JF152J J 1.5k 1/16W VRS-CY1JF153J J 15k 1/16W VRS-CY1JF474J J 470k 1/16W VRS-CY1JF153J J 15k 1/16W VRS-CY1JF681J J 680 1/16W VRS-CY1JF823J J 82k 1/16W VRS-CY1JF222J J 2.2k 1/16W VRS-CY1JF222J J 2.2k 1/16W VRS-CY1JF102J J 1.0k 1/16W VRS-CY1JF221J J 220 1/16W VRS-CY1JF122J J 1.2k 1/16W VRD-RA2BE562J J 5.6k 1/8W VRD-RA2BE102J J 1.0k 1/8W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF103J J 10k 1/16W VRS-CY1JF332J J 3.3k 1/16W VRS-CY1JF332J J 3.3k 1/16W VRS-CY1JF473J J 47k 1/16W VRS-CY1JF473J J 47k 1/16W EL. EL. EL. Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic EL. EL. Ceramic Ceramic Ceramic EL. Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic EL. EL. Ceramic AB AB AB AA AA AB AA AA AA AA AB AB AA AA AA AC AA AA AA AA AA AA AA AE AE AA Part No. R1212 R1213 R1214 R1215 R1216 R1218 R1219 R1220 R1221 R1222 R1223 R1224 R1225 R1226 R1227 R1229 R1230 R1231 R1232 R1233 R1234 R1235 VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF221J VRS-CY1JF221J VRS-CY1JF221J VRD-RA2BE102J VRD-RA2BE102J VRS-CY1JF103J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF561J VRS-CY1JF561J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF221J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J VRS-CY1JF102J FB1101 FB1102 FB1103 CN1001 CN1101 CN1201 P1102 P1201 P1202 P1203 P1206 RBLN-0043CEZZ RBLN-0043CEZZ RBLN-0043CEZZ QSOCN0913REN1 QSOCN2913REN1 QPLGN0980GEZZ QPLGN1280GEZZ QPLGN0680GEZZ QPLGN1180GEZZ QPLGN0580GEZZ QPLGN0280GEZZ ★ J J J J J J J J J J J J J J J J J J J J J J Description 10k 10k 220 220 220 1.0k 1.0k 10k 10k 0 0 560 560 10k 1.0k 220 1.0k 1.0k 1.0k 1.0k 1.0k 1.0k 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS RESISTORS M-Ox. Carbon Carbon Carbon M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Carbon Carbon M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. M-Ox. Ref. No. AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 175 J J J J J J J J J J J Ferrite Bead Ferrite Bead Ferrite Bead Socket, 9-pin(CA) Socket, 29-pin(CB) Plug, 9-pin(CC) Plug, 12-pin(DA) Plug, 6-pin(DC) Plug, 11-pin(DD) Plug, 5-pin(DB) Plug, 2-pin(DF) AB AB AB AC AF AC AC AB AC AB AB 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code MECHANISM CHASSIS 1 2 3 5 6 7 8 9 10 11 12 15 16 17 18 19 20 21 22 23 24 25 26 27 29 30 31 32 33 34 35 36 37 38 39 40 41 43 44 45 46 47 48 49 50 51 52 53 55 56 57 58 59 60 61 62 63 65 66 LBNDK1011AJZZ LBOSZ1007AJZZ LBOSZ1006AJZZ LCHSM0175AJZZ LHLDZ2016AJZZ LPOLM0070GEZZ LPOLM0064GEZZ MLEVF0518AJZZ MLEVF0519AJZZ MLEVF0499AJZZ MLEVF0500GEZZ MLEVF0523AJZZ LANGF9620AJFW MLEVP0271AJZZ MLEVP0272AJZZ MLEVP0301AJZZ MLEVP0275AJZZ MLEVP0292AJZZ MLEVP0336AJZZ MLEVP0293AJZZ MLEVP0324AJZZ MLEVP0325AJZZ CLEVP0287AJZZ MSLiP0010AJZZ MSPRD0175AJFJ MSPRT0402AJFJ MSPRT0403AJFJ MSPRC0213AJFJ MSPRT0416AJFJ NBLTK0067AJ00 NDAiV1078AJ00 NGERH1293AJZZ NGERH1295AJ00 NGERH1294AJZZ NGERH1270AJZZ NGERH1271AJZZ NGERH1272AJZZ NGERH1299AJZZ NGERW1070AJZZ NGERW1066AJZZ NiDR-0018AJZZ NPLYV0162AJZZ NPLYV0163AJZZ NROLP0131GEZZ NSFTP0032AJZZ MSPRC0217AJFJ PREFL1011AJZZ QCNW-8022AJZZ QCNW-8021AJZZ QPWBF5243AJZZ QSOCN0696REZZ RHEDT0036AJZZ RHEDU0089GEZZ RMOTM1078GEZZ RMOTN2067GEZZ RMOTP1151GEZZ DDRMW0030TEXC QBRSK0041GEZZ XBPSD26P05J00 V V V V V J J V V V J V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V J V V V V V V V V J J J J V J V 67 68 69 70 71 75 76 PGiDC0056GEFW QPWBF5468AJZZ QPLGZ0292GEZZ MSPRC0228AJFJ MSPRC0224AJFJ CARMP0059GE01 MSPRD0183GEFJ J V J V V V J Tension Band Ass’y Tension Arm boss Cassette Stay L Main Chassis Ass’y Loading Motor Block Supply Pole Base Ass’y Take-up Pole Base Ass’y Take-up Loading Arm Ass’y Supply Loading Arm Ass’y Pinch Drive Lever Ass’y Pinch Roller Lever Ass’y Tension Arm Ass’y A/C Head Plate Shifter Drive Lever Pinch Double Action Lever Reverse Guide Lever Ass’y Reverse Guide Drive Lever Slow Brake Lever Open Lever Clutch Lever Supply Main Brake Ass’y Take-up Main Brake Ass’y Auto Head Cleaner Shifter Reverse Guide Spring Loading Double Action Spring Pinch Double Action Spring Earth Spring Tension Spring Loading Belt Spindle Loading Connect Gear Master Cam Casecon Drive Gear Take-up Loading Gear Supply Loading Gear Pinch Drive Cam Reel Relay Gear Worm Gear Worm Wheel Gear Idler Motor Pulley Limiter Pulley Ass’y Guide Roller Tension Pole Adjuster Guide Roller Spring Light Guide FFC for Drum Motor FFC for A/C Head A/C Head PWB Socket, 6 pin Full Erase Head A/C Head Ass’y Loading Motor Capstan Motor D.D. Motor Upper and lower Drum Drum Earth Brush Drum Drive Motor Mounting Screw (SW2.6P+5S) Drum Base PWB(LDG Motor) Socket(LDG Motor) Azimuth Spring Height Adjusting Spring Impedance Roller Arm Ass'y Spring Ref. No. Part No. ★ Description Code SCREW, NUTS AND WASHERS AH AD AD AV AG AK AM AF AF AG AW AH AG AE AD AL AD AE AD AE AF AF AG AH AE AE AD AC AD AE AE AD AE AD AF AD AE AE AD AD AK AD AM AL AB AC AE AD AD AE AB AM AP AP AY AT BH AD AA 201 202 203 207 208 209 210 211 212 213 214 216 218 219 220 221 222 223 224 AL AE AE AB AC AS AC 176 XBPSD26P08000 LX-HZ3082GEZZ XJPSD26P06000 V Screw, 2.6P+8S A/C Head J Screw, WSW 2.6+6 V Screw, C2.6P+6S (For Capstan Motor) XHPSD30P08WS0 V Screw, C3SP+8S (For Drum Base) XRESJ30-06000 V E-Ring, E-3 XWHJZ31-03052 V Washer, W3.1 P-5.2-0.3 XWHJZ31-04052 V Washer, W3.1 P-5.2-0.4 XWHJZ31-05052 V Washer, W3.1 P-5.2-0.5 XWHJZ31-06052 V Washer, W3.1 P-5.2-0.6 XWHJZ31-07052 V Washer, W3.1 P-5.2-0.7 PSPAP0009AJZZ V Reverse Guide Adjusting Nut LX-WZ1041GE00 J Washer, CW 2.6-6-0.5 CAM XBPSD30P06J00 V Drum Base Mounting Screw (SW 3P+6S) LX-WZ1098GE00 J Washer, CW 2.6-4.7-0.5 RED LX-BZ3096GEFD J Tilt Adjusting Screw XBPSD26P06000 V Azimuth Adjusting Screw XBPSD26P14000 J Screw(A/C Head) XWHJZ31-08052 V Washer, W3.1 P-5.2-0.8 XHPSD26P06WS0 J Screw, C2.6P+6S(AC) AA AD AA AA AA AC AC AC AC AC AB AA AA AB AA AA AA AC AA 27DV-S100 27DV-CS10 MECHANISM CHASSIS PARTS (VCR PARTS) 66 H 66 53 62 55 66 222 220 66 70 26 65 221 62 57 G 59 63 56 201 224 202 207 207 16 50 71 216 F 49 1 75 67 22 51 218 76 8 15 49 58 E 33 51 25 52 2 24 31 32 11 214 12 4 7 19 18 20 D 203 29 35 35 C 46 5 209 210 211 212 213 223 216 41 43 61 43 23 9 21 10 39 30 B 30 36 38 34 17 40 37 48 6 45 208 44 27 A 47 60 219 68 69 1 2 3 4 177 5 6 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code CASSETTE HOUSING CONTROL 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 CHLDX3081TEV2 LANGF9592AJFW LHLDX1030AJZZ LHLDX1031AJZZ LHLDX1032AJ00 LHLDX1028AJ00 MLEVF0469AJFW MLEVP0281AJ00 MSLiF0077AJFW MSPRD0151AJFJ MSPRD0166AJFJ MSPRP0175AJFJ MSPRT0381AJFJ NGERH1278AJZZ NGERH1309AJZZ NGERR1008AJ00 NGERR3005AJFW NSFTD0041AJFD V V V V V V V V V V V V V V V V V V Cassette Housing Control Ass’y Upper Plate Holder (L) Holder (R) Frame (R) Frame (L) Proof Lever (R) Door Open Lever Slider Proof Lever (R) Spring Drive Gear (R) Spring Cassette Spring Double Action Spring Drive Gear L Drive Gear R Double Action Rack Gear Drive Angle Gear Main Shaft AX AL AE AE AH AH AE AD AE AB AE AE AC AE AE AE AG AH 178 Ref. No. Part No. ★ Description Code 27DV-S100 27DV-CS10 CASSETTE HOUSING CONTROL PARTS H 300 301 G 304 F 302 311 311 305 306 308 E 309 313 310 D 317 303 314 C 312 307 B 315 316 A 1 2 3 4 179 5 6 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code MECHANISM PARTS (DVD PART) 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 CMECD0211HJV1 LX-BZ3189GEZZ NGERH1330AJZZ NGERH1341AJ00 LX-WZ1030GE00 LX-BZ3163GEFN QSW-M0066AJZZ DUNTK6062TEV1 RMOTV2019AJZZ NGERH1333AJZZ NGERR1021AJZZ MSPRC0244AJZZ NGERR1024AJZZ LX-HZ0083TAFF PCUSG0126AJZZ LX-HZ3117AJZZ QCNW-8559AJZZ QCNW-8561AJZZ MSLiP0014AJZZ LHLDZ2144AJZZ QCNW-8560AJZZ LHLDW1033CE00 RMOTM1097AJZZ NPLYM0001AJZZ QSW-B0011AJZZ NBLTK0068AJZZ NGERH1332AJZZ NGERP1016AJZZ LCHSM0314AJZZ LCRA-0002GEZZ LX-WZ0102GEFD PMAGS1001GEZZ GCOVA2164AJZZ LX-BZ3434AJFD V J V V J J V V V V V V V V V V R R V V R R V V V V V V V J J J V V Mecha Chassis Ass’y Guide Axis Pressing Biss Relay Gear1 Relay Gear2 Relay Gear Washer Motor Screw In SW Sled Motor PWB Unit Sled Motor Sled Motor Gear Double Action Rack Rack Spring Rack Rack Fixing Screw Insulator Traverse Fixing Screw Sled Wire Pickup Relay FFC Slide Rack Traverse Holder Loading Wire Nylon Band Loading Motor L Motor Pulley Loading Switch Loading Belt Pulley Gear Tray Pinion Base Chassis Disc Clamper York Washer Magnet Tray L Motor Fixing Screw BU AB AC AC AA AC AD AE AM AB AC AB AC AA AD AC AF AF AD AD AD AA AM AB AE AD AC AC AL AD AB AF AH AB 180 Ref. No. Part No. ★ Description Code 27DV-S100 27DV-CS10 MECHANISM CHASSIS PARTS (DVD PARTS) Dry Coating H Dry Coating Dry Coating 20 G 16 18 Dry Coating F 19 17 Grease 21 E Grease 15 14 12 13 1-11 7 D 1-13 11 Grease Grease 1-10 1-12 1-4 1-3 9 1-2 3 10 2 8 C Grease 6 5 1-5 3 2 2 B å Caution When touching the pickup, wear an earth band to prevent breakage by static electricity. 1-9 1-1 3 1-8 2 A 3 1 2 3 1 4 1-6 1-7 3 4 181 5 6 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code 22 23 24 25 26 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 53 54 55 57 58 59 60 61 62 63 64 65 CABINET AND MECHANICAL PARTS 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-7-1 1-7-2 1-7-3 1-7-4 1-7-5 1-7-6 1-8 1-8-1 1-8-2 1-8-3 1-8-4 1-8-5 1-8-6 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 1-21 1-22 1-23 1-24 1-25 1-26 1-27 CCABA2672WEV1 Not Available HPNLC0063PEKA HBDGB3141CESA JBTN-0392PESA HDECQ0222PESA HDECQ0210PESB CBTN-0393WEV1 Not Available HDECQ0225PESA HDECQ0226PESA HDECQ0227PESA HDECQ0228PESA HDECQ0229PESA CBTN-0394WEV1 Not Available HDECQ0225PESA HDECQ0226PESA HDECQ0227PESA HDECQ0229PESA HDECQ0229PESA GCOVA0144PESA GCOVA0140PESA MSPRC0005PEFW MSPRD0006PEZZ MSPRD0123AJFJ XEBSD30P12000 PSPAH0111PE00 VSP0080PBQ8WA XEBSD40P12000 PMLT-0029PEZZ LHLDZ0015PEZZ TCAUS0010PEZZ PSPAH0065PE00 PSPAH0066PE00 PGUMS0027AJZZ GDORF0195PESA LHLDS1010AJZZ TLABZ0179PEZZ HDECQ0224PESA 2 2-1 2-2 2-3 2-3 2-4 2-5 CCABB2455WEV1 R Rear Cabinet Ass’y (27DV-CS10) CCABB2455WEV3 R Rear Cabinet Ass’y (27DV-S100) Not Available – Rear Cabinet HiNDP0289PEZZ R Antenna Indication Plate TLABS0220PEZZ R Liscense Label(27DV-CS10) TLABS0221PEZZ R Liscense Label(27DV-S100) PSPAH0018PE00 R Spacer, x3 TCAUH0051PEZZ R Caution Label — AE AD AB AC AD 3 4 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 QACCD3064CESA TLABM1829PEZZ TLABM1830PEZZ PSLDM0340PEFW PSLDM0250PEFW PSLDM0334PEFW PSLDM0264PEFW LANGT0038PEFW QEARC2913PEZZ LCHSM0131PEKZ LCHSM0129PEKZ LHLDZ0161PEZZ HDECQ0211PESA PSLDM0253PEFW LANGF0040PEFW PSLDM0339PEFW PSLDM0342PEFW PSLDM4566AJFW LANGF0041PEFW PSPAG0003PEZZ AM AB AB AK AD AH AG AC AK AP AV AG AD AC AE AN AG AD AD AD 2 å R – R J R R R R – R R R R R R – R R R R R R R R R J J R R J R R R R R J R J R R J R R R R R R R R R R R R R R R R J R R Front Cabinet Ass’y Front Cabinet Front Panel Badge, "SHARP" Power Button VCR Flap Door DVD Flap Door VCR Control Button Ass’y VCR Control Button Button, REW Button, PLAY Button, FF Button, REC Button, STOP DVD Control Button Ass’y DVD Control Button Button, SKIP/REV(reverse) Button, PLAY Button, SKIP/FWD(forward) Button, STOP Button, OPEN-CLOSE DVD/VCR LED Cover R/C-LED Cover Spring, for Power Button Spring, for DVD Spring, for VCR Screw, x6 Spacer Speaker, x2 Screw, x4 Spacer, for Speaker Bonding Spacer, x2 Caution Card Spacer, x2 Spacer, x2 Spacer, for Door Door Door Latch Indication Label, in Door Decoration Plate AC Cord (ACC901) Model Label(27DV-S100) Model Label(27DV-CS10) DVD Bottom Shield VCR Top Cover VCR Top Shield VCR Bottom Shield Mecha Angle Grounding Strap Main Chassis Sub Chassis Holder (DVD PWB) Decoration Plate H/A Angle Angle (DVD PWB) DVD Top Shield DEF Shield FFC Shield Support Angle Spacer, x3 Ref. No. BR — AV AG AF AH AH AP — AD AD AD AD AD AN — AD AD AD AD AD AD AD AB AC AC AA AB AK AA AC AD AB AC AD AB AF AB AC AH BH BH 182 Part No. LX-TZ0017PEFD LX-WZ0001PEFD LX-WZ0011PEFD DUNTKA686WEV1 DUNTKA603WEV5 DUNTKA603WEV6 DUNTKA640WEV1 DUNTKA680WEV1 DUNTKA639WEV1 DUNTKA637WEV1 DUNTKA638WEV1 DUNTKA669WEV1 DUNTKA642WEV1 DUNTKA643WEV1 DUNTK6054TE6H DUNTK6081TEV1 VB68LUW696X~S RCiLG0056PEZZ PMAGF3040CEN1 RCiLH0259PEZZ QSW-F0042AJZZ XTASD40P25000 LHLDZ1962AJ00 PSLDM0335PEFW PSLDM0336PEFW LHLDK0011PEZZ LHLDK0016PEZZ XEBSD30P12000 LX-HZ3001PEFD XHPSD30P06WS0 XHPSD26P06WS0 PSPAH0004PE00 LHLDW1067PEKZ LHLDW1061PEKZ LHLDW0003PEKZ LHLDZ0133PEZZ XTASD30P12000 LHLDW1019PEKZ LHLDW1063PEKZ LHLDW1075PEKZ LHLDW0017PEKZ LHLDW1064PEKZ LHLDZ0167PEKZ ★ Description Code R R R – – – – – – – – – – – – – J R J R J J J R R R R J J J J R R R R R J R R R R R R Screw, x4, for CRT Washer, x4, for CRT Washer, x4, for CRT CRT Unit MAIN Unit(27DV-S100) MAIN Unit(27DV-CS10) TERMINAL Unit TERMINAL SUB Unit TV POWER Unit DVD/VCR POWER Unit DEFLECTION Unit FRONT AV Unit DVD CONTROL Unit VCR CONTROL Unit DVD MAIN Unit DVD SUB Unit Picture Tube Degaussing Coil Purity Magnet Deflection Yoke Rec Tip Switch(S7001) Screw Start, End Sensor Holder H/A Shield (Top) H/A Shield (Btm) Holder Holder Screw, x6 Screw, x6 Screw Screw Spacer Holder Holder ADG Coil Holder, x4 Anode Clamp Holder Screw Holder Holder Holder Wire Holder, x1 Holder Holder AF AB AB — — — — — — — — — — — — — CV AS AN BN AG AA AD AC AC AE AC AA AA AA AA AA AC AD AB AC AA AC AD AC AB AC AF 1 2 3 4 183 1 1-4 5 1-6 1-11 1-5 6 1-10 1-27 1-23 1-15 1-18 1-7-4 1-14 1-24 1-14 1-7-2 1-7-3 1-12 1-7-5 1-7-1 1-7 1-16 1-8-6 1-8-3 1-8-3 1-26 1-25 1-2 1-9 1-7-6 1-3 1-21 1-19 24 1-8-5 1-8-4 1-17 49 1-18 1-17 23 48 22 24 1-20 1-14 1-1 34 1-8 1-8-1 23 39 33 1-16 54 48 62 49 1-22 48 1-19 49 68 C 1-13 1-17 37 40 57 62 A 50 6 53 54 49 B 53 D 12 61 19 65 8 3 50 48 46 47 63 49 51 7 9 30 48 B 41 55 26 48 A 43 44 45 48 48 64 42 15 50 32 49 61 54 E 23 B 21 62 25 60 58 18 48 31 2 55 28 2-4 61 27 54 48 2-4 42 48 2-5 2-1 48 20 11 29 2-4 14 5 4 2-3 56 62 17 G 24 24 A 23 10 38 57 16 35 60 59 50 48 2-2 42 56 13 36 48 42 27DV-S100 27DV-CS10 CABINET AND MECHANICAL PARTS H F 27DV-S100 27DV-CS10 Ref. No. Part No. ★ Description Code ACC901 QACCD3064CESA RCORF0031CEZZ QCNW-A083WJZZ QCNW-A084WJZZ QCNW-A087WJZZ QCNW-A088WJZZ QCNW-A096WJZZ QCNW-A131WJZZ QCNW-A192WJZZ QCNW-A193WJZZ QCNW-A203WJZZ QCNW-2622PEZZ QCNW-2626PEZZ QCNW-2627PEZZ QCNW-2630PEZZ QCNW-5030PEN3 LHLDW0015PEKZ LX-WZ1041GE00 LX-WZ1044GE00 XEBSD30P12000 XEBSD40P12000 LX-BZ3100CEFD LX-BZ3100CEFD LX-BZ3100CEFD LX-HZ3001PEFD PSPAH0111PE00 XWHJZ21-05050 J J R R R R R R R R R R R R R R R J J J J J J J R R J AC Cord Ferrite Core, x2 Connecting Cord(AR) Connecting Cord(ZA) Connecting Cord(SE) Connecting Cord(SE) Connecting Cord(N) Connecting Cord(EB) Connecting Cord(WA) Connecting Cord(GBN) Connecting Cord(BA) Connecting Cord(SA/SB) Connecting Cord(SC) Connecting Cord(OC) Connecting Cord(GA) Connecting Cord(OR) Holder Washer, x1 Washer Screw, x36 Screw, x15 Screw Screw Screw Screw, x2 Spacer, x1 Washer R Guarantee Card (27DV-S100) TiNS-7463PEZZ R Operation Manual (27DV-S100) TiNS-7464PEZZ R Operation Manual (27DV-CS10) RRMCG1687PESA R Infrared R/C Unit ★ Description Code (NOT REPLACEMENT ITEM) AM AM AC AE AG AF AE AF AF AF AE AE AE AF AE AD AB AA AA AA AA AA AA AA AA AB AA SUPPLIED ACCESORIES TGAN-0018PEZZ Part No. PACKING PARTS MISCELLANEOUS PARTS å Ref. No. AD AL AQ BH 184 SPAKC6759PEZZ SPAKC6764PEZZ SPAKP0083PEZZ SPAKP0110PEZZ SPAKX2779PEZZ SSAKA0031PEZZ – – – – – – TLABN0001PEZZ TLABK0002PEZZ TLABZ0174PEZZ TLABR7022PEZZ – – – – Packing Case(27DV-S100) Packing Case(27DV-CS10) Polyethylene Sheet Wrapping Paper, for AC Cord Buffer Material Polyethylene Bag, for Accessories Serial Number Label Number Label Feature Tag(27DV-CS10) UPC Label (27DV-CS10) — — — — — — — — — — 27DV-S100 27DV-CS10 PACKING OF THE SET • SETTING POSITIONS OF THE KNOBS Power SW OFF ★ Polyethylene Bag Operation Manual Guarantee Card (27DV-S100) ★ Batteries Infrared R/C Unit ★ Polyethylene Sack ★ Buffer Material (Top and Bottom) ★ Packing Case ★ Serial Number Label FRONT Use 22 staples to fix the packing case. REAR ★ Number Card MARK ★ : Not Replacement Items. 185 27DV-S100 27DV-CS10 COPYRIGHT © 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan TQ1248-S Nov. 2001 Printed in Japan D JAPAN P SREC MI. KG 186