Transcript
Bouncepad Desk with Tilt
Tools you’ll need...
Assembly Instructions a
c
b
d
e
f
Tools Key a
Pencil
b
Drill
c
5/8” Drill Bit
d
1/4” Drill Bit
e
Adjustable Wrench
f
Socket Screwdriver
What’s in the box? Components Key
2 3
4
5
6
1
Note your key number
1
7
8
9
11
10
12
13
14
1
Secure Case
2
Desk
3
Surface Mounting Kit
4
Key x 2
5
Mounting Washer
6
Case Washer
7
M4 Wingnut x 4
8
T20 Pin Torx Driver Bit
9
M4 Round Washer x 4
10
M4 Hex Nut x 4
11
M4 x 10mm Pin Torx Countersunk Screw x4
12
M4 x 25mm Pin Torx Buttonhead Screw x4
13
M4 x 40mm Socket Setscrew PCP x 4
14
No. 8 x 1 ½ Pin Torx Self Tapping CSK Screw x4
To mount from underneath the surface drill the mounting holes in your surface using the Mounting Washer as a template. If you wish to secure the Bouncepad from above your surface, use the Surface Mounting Kit provided. See point 10 for more details.
d d
5/8” b a
c
d
d
c + d
5 6
d
1/4”
2
Attach Socket Setscrews to the Desk Mount.
Attach the Desk Mount to your surface. For faster installation use the 4 x M4 Wingnuts ( 7 ) in place of the M4 Hex Nuts. You will need to feed the USB cable through before fully tightening the wingnuts due to their larger size and shape.
3
2
2
5
13
9 10
e
13
Remember, wingnuts can be undone by hand, so consider the security of your installation before choosing this mounting method.
toll free 1-888-423-3885 l local 1-617-275-8131 l www.thebouncepad.com l Bouncepad North America, Inc. 50 Terminal St, Unit 710, Building 2, 7th Floor, Charlestown, MA 02129, USA l
2013 Bouncepad Spotspot Ltd. All rights reserved.
Attach the Secure Tablet Case to the Desk Mount. Be sure to fully engage both screws in their threads before tightening. Always use a hand screwdriver for this step.
4
f
5
Complete the alignment of the Bouncepad. Firstly, loosen the screws (shown below) slightly and align the case to be horizontal. Then, when the case is aligned, tighten screws up again using a hand screwdriver.
f
8 12 6
You can mount the case portrait or landscape.
Feed the USB cable through the Mounting Arm from above.
6
7
Unlock and remove the face of Secure Case.
4
8
Connect cable to Tablet and place into Secure Case. Your Bouncepad is set up to house the tablet model specified in your order. If you need to use a different tablet, please contact us for a conversion kit.
10
Using the Surface Mounting Kit (alternative to points 1, 2 & 3). Slide the Plate Cover over the Desk Mount from the bottom, then attach the Surface Mounting Plate to the Desk Mount using the M4 x 10mm Pin Torx Countersunk Screws. Attach the assembly to your surface using suitable screws ( 14 ).
9
Lock the face of Secure Case back into place. Place the cable end of the faceplate first, then squeeze the lock end while turning the key.
Installation guidelines. To minimise glare on the screen, avoid installing the Bouncepad directly below a source of light. Maintenance of your Bouncepad. To keep your Bouncepad looking its best, clean regularly with screen wipes.
Surface Mounting Kit
3
“diam. 2
11/64” diam.
3 “ (from centre of screen)
1 “ diam. 11
2
cable channel
“
diam.
(recommended height from the ground to the center of the screen)
not to scale
toll free 1-888-423-3885 l local 1-617-275-8131 l www.thebouncepad.com l Bouncepad North America, Inc. 50 Terminal St, Unit 710, Building 2, 7th Floor, Charlestown, MA 02129, USA l
2013 Bouncepad Spotspot Ltd. All rights reserved.
