Transcript
BP3/10
PCI/ISA BACKPLANE FEATURES · 14-slot form factor supports one PICMG® 1.0 single board computer · Ten PCI and two ISA option card slots · PCI card slot configurations: Ten slots support 32-bit/33MHz PCI option cards · Optimized for use with Trenton high-performance PICMG 1.0 single board computers · PCI-to-PCI bridge architecture ensures independent PCI card operations · PCI bus mastering available on all 10 PCI option card slots · Flexible input power connector configuration options · Two-year factory warranty · Made in U. S. A.
Dependable, always.
BLOCK DIAGRAM:
ISA Connectors SLT11, SLT12
ISA Bus Processor Slot (SBC)
Primary PCI Bus
PCI to PCI Bridge
PCI to PCI Bridge
PCI to PCI Bridge
Secondary PCI Bus PCI Connectors A1 & A2
PCI Connectors B1, B2, B3, B4
PCI Connectors C1, C2, C3, C4
Copyright c2001 Trenton Technology Inc.
PICMG 1.0 BACKPLANE WITH PCI and ISA SLOTS: The Trenton BP3/10 backplane supports PICMG® 1.0 single board computers (SBCs). PCI-toPCI bridge chips used on this backplane extend the PCI local bus electrical loading limits while ensuring secure data communications between the PCI option cards and the SBC. The bridge chips operate independently and allow communication within the same bus even if all the other PCI buses on the backplane are busy. This design feature helps to ensure that data packets on a PCI bus are not lost during times of peak data traffic. All ten PCI option card slots on the backplane support bus mastering. Two ISA option card slots connect directly to the SBC’s ISA card edge fingers when the SBC is installed in the processor slot.
APPLICATION EXAMPLES:
A system design needing to support a number of COTS PCI option cards and a few purposebuilt ISA cards simultaneously is the ideal application scenario for the BP3/10 backplane. All of the backplane’s card slots support 32-bit/33MHz PCI option cards. The backplane’s two ISA card slots support purpose-built ISA cards where the cost of designing out these legacy cards is prohibitive. The BP3/10 backplane design offers secure data communications support for legacy PCI and ISA option cards which extends system usability and value by eliminating the need for costly option card upgrades. Example applications include; transportation, telecommunications, industrial automation and military systems.
BACKPLANE MODEL: BP3/10 MODEL# 5937-000 5937-001
DESCRIPTION Standard AT input power connectors Standard ATX input power connectors
TRENTON Technology Inc. 2350 Centennial Drive, Gainesville, Georgia 30504 Sales: (800) 875-6031 Phone: (770) 287-3100 Fax: (770) 287-3150 E-mail:
[email protected] Web: www.TrentonTechnology.com
BP3/10 LAYOUT: SUGGESTED TRENTON PICMG 1.0 SBCs: MX8 T4G T4R T4I
12.300 8.975 7.775* 6.275
2.525 1.637* .845
4.150
.800
2.075
* = Pin 1
0.400 SLT11
SLT12
0.600*
SLTP1 SLTA1
SLTA2
SLTB1
SLTB2
SLTB3
SLTB4
SLTC1
SLTC2
SLTC3
1.225*
SLTC4 P1 1
6.100 6.325* P2
8.900
1
10.100
PCI ISA
SLTP2 +3.3V
Processor Slot
PCI to PCI Bridge
PCI to PCI Bridge
PCI to PCI Bridge
P9 1
+5V
P10 1
-12V 1
P12 -5V +12V
Copyright c2002 Trenton Technology Inc.
ENVIRONMENTAL SPECIFICATIONS:# Operating Temp.: 0° C. to 60° C Storage Temp.: -20° C. to 70° C Humidity: 5% to 90%, non-condensing #
Environmental specifications for single board computers are usually lower than those of the backplane. Check with your SBC vendor.
The Trenton BP3/10 is available as either a non-RoHS or a lead-free, RoHS compliant backplane. This backplane is designed to meet worldwide EMI emissions requirements, CE conformity and immunity standards. Contact Trenton for specific standard numbers.
P11
1.825 2.125 2.525
Copyright c2003 Trenton Technology Inc.
Engineering Notes: All power connectors are shown in the layout drawings. The connectors are populated based on model. Nominal PCB thickness: 0.062” Connector spacing: .800” centers To find the center of a PCI option card connector to the left of the reference dimension hole, add 0.150” to the pin 1 location dimension. Mounting holes: 0.156” diameter All dimensions are inches.
Product Photo Note: The photo of the 5937 backplane shown on page one is provided for illustrative purposes only. Actual connector locations are illustrated in the backplane layout drawings and on the Trenton website.
PICMG is a registered trademark of the PCI Industrial Computer Manufacturers Group. All other product names are trademarks of their respective owners.
Copyright ©2009 by TRENTON Technology Inc. All rights reserved.
The Trenton BP3/10 backplane is designed for UL approval.
Dependable, always.
TRENTON Technology Inc. 2350 Centennial Drive, Gainesville, Georgia 30504 Sales: (800) 875-6031 Phone: (770) 287-3100 Fax: (770) 287-3150 E-mail:
[email protected] Web: www.TrentonTechnology.com
8415937 11129 1.0
