Transcript
OPERATION INSTRUCTIONS 2012/912 Single Wire End Fed Portable Broadband Dipole The Barrett 912 single wire end fed portable broadband antenna, with a frequency range of 3 to 30 MHz, is designed for easy deployment making it ideal for temporary or emergency situations. The antenna’s solid metal housings with stainless steel wire and fittings are designed to ensure maximum life under the most adverse climatic and operational conditions. Being end fed the 2012/912 broadband portable antenna is quick and simple to install, requiring a mounting point such as a small pole or tree, the other end being attached to either a vehicle bull bar or the housing of a portable transceiver. Because the 912 end fed portable is a broadband antenna NO ANTENNA TUNER IS REQUIRED. If mounted high enough the 2012/912 end fed portable antenna will easily out perform mobile whip antennas, making it excellent for use in locations such as temporary base camps. Even if the existing vehicle installation has a manual tapped whip or an auto-tune mobile antenna the 2012/912 end fed portable antenna is good insurance in case of vehicle damage caused by roll overs or damage to the mobile whip antenna caused 912 Single Wire End Fed Portable Antenna Deployment
! Unfurl the broadband antenna from the winding bobbin supplied. ! Push the earth stake into the ground. Clip the short wire from the balun box, with the coaxial connector on it, to the earth stake using the crocodile clip supplied.
! Hang the wire section of the antenna in any configuration convenient as
indicated in the diagrams. Note the higher from the ground the more efficient the antenna will be.
! Connect the coaxial cable from the coaxial socket on the blue box on the antenna to the transceiver antenna socket..
! The
antenna is now ready for operation, no tuning or adjustments are required.
NYLON HALYARD NYLON HALYARD
LOAD CASE
NYLON LEADTHROUGH 16 METRES BALUN WRAP 3m CABLE AROUND BULLBAR INSULATOR COAXIAL FEEDER TO TRANSCEIVER
BCM201204/1
8 METRES HANG COUPLING SECTION EITHER VERTICALLY OR AT AN ANGLE USING A NYLON HALYARD
OPERATION INSTRUCTIONS 2012/912 Single Wire End Fed Portable Broadband Dipole The Barrett 912 single wire end fed portable broadband antenna, with a frequency range of 3 to 30 MHz, is designed for easy deployment making it ideal for temporary or emergency situations. The antenna’s solid metal housings with stainless steel wire and fittings are designed to ensure maximum life under the most adverse climatic and operational conditions. Being end fed the 2012/912 broadband portable antenna is quick and simple to install, requiring a mounting point such as a small pole or tree, the other end being attached to either a vehicle bull bar or the housing of a portable transceiver. Because the 912 end fed portable is a broadband antenna NO ANTENNA TUNER IS REQUIRED. If mounted high enough the 2012/912 end fed portable antenna will easily out perform mobile whip antennas, making it excellent for use in locations such as temporary base camps. Even if the existing vehicle installation has a manual tapped whip or an auto-tune mobile antenna the 2012/912 end fed portable antenna is good insurance in case of vehicle damage caused by roll overs or damage to the mobile whip antenna caused 912 Single Wire End Fed Portable Antenna Deployment
! Unfurl the broadband antenna from the winding bobbin supplied. ! Push the earth stake into the ground. Clip the short wire from the balun box, with the coaxial connector on it, to the earth stake using the crocodile clip supplied.
! Hang the wire section of the antenna in any configuration convenient as
indicated in the diagrams. Note the higher from the ground the more efficient the antenna will be.
! Connect the coaxial cable from the coaxial socket on the blue box on the antenna to the transceiver antenna socket..
! The
antenna is now ready for operation, no tuning or adjustments are required.
NYLON HALYARD NYLON HALYARD
LOAD CASE
NYLON LEADTHROUGH 16 METRES BALUN WRAP 3m CABLE AROUND BULLBAR INSULATOR COAXIAL FEEDER TO TRANSCEIVER
BCM201204/1
8 METRES HANG COUPLING SECTION EITHER VERTICALLY OR AT AN ANGLE USING A NYLON HALYARD
NYLON LEADTHROUGH
LOAD CASE
TEMPORARY MASTBROKEN WHIP ANTENNA, LONG-HANDELED SHOVEL, TENT POLES ETC BALUN LASHED TOGETHER
WRAP 3m CABLE AROUND BULLBAR
INSULATOR NYLON HALYARD
COAXIAL FEEDER TO TRANSCEIVER
NYLON LEADTHROUGH NYLON HALYARD
LOAD CASE
16
WRAP 3m CABLE AROUND BULLBAR
M
ET
S RE
8 METRES
HANG COUPLING SECTION EITHER VERTICALLY OR AT AN ANGLE USING A NYLON HALYARD
BALUN COAXIAL FEEDER TO TRANSCEIVER
NYLON LEADTHROUGH NYLON HALYARD
LOAD CASE CROCODILE CLIP FROM ANTENNA CLIPPED TO EARTH STAKE
16
M
E
E TR
S
8 METRES
HANG COUPLING SECTION EITHER VERTICALLY OR AT AN ANGLE USING A NYLON HALYARD
BALUN INSULATOR
COAXIAL FEEDER TO TRANSCEIVER
INSULATOR
NYLON LEADTHROUGH
LOAD CASE
TEMPORARY MASTBROKEN WHIP ANTENNA, LONG-HANDELED SHOVEL, TENT POLES ETC BALUN LASHED TOGETHER
WRAP 3m CABLE AROUND BULLBAR
INSULATOR NYLON HALYARD
COAXIAL FEEDER TO TRANSCEIVER
NYLON LEADTHROUGH NYLON HALYARD
LOAD CASE
16
WRAP 3m CABLE AROUND BULLBAR
M
ET
S RE
8 METRES
HANG COUPLING SECTION EITHER VERTICALLY OR AT AN ANGLE USING A NYLON HALYARD
BALUN COAXIAL FEEDER TO TRANSCEIVER
NYLON LEADTHROUGH NYLON HALYARD
LOAD CASE CROCODILE CLIP FROM ANTENNA CLIPPED TO EARTH STAKE
16
M
ET
S RE
8 METRES
HANG COUPLING SECTION EITHER VERTICALLY OR AT AN ANGLE USING A NYLON HALYARD
BALUN INSULATOR
COAXIAL FEEDER TO TRANSCEIVER
INSULATOR
