Transcript
BUSH HOG
®
LAND MAINTENANCE REPAIR PARTS MANUAL MODEL: 4214 SECTION: 57
2501 Griffin Ave. • Selma, AL 36703 (334) 872-6261 • (334) 874-2700 Parts Ordering 1-800-304-2836 Fax 1-800-572-1784 www.bushhog.com
BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL
JULY, 2002
4214 ROTARY CUTTER ALPHABETICAL INDEX CONTENTS
PAGE
Axle Weldment .................................................................................................................................................57-1-1 Axle Arms (Pull Models)....................................................................................................................................57-6-2 Axle Arms (Lift Models).....................................................................................................................................57-7-2 Baffle Kit............................................................................................................................................................57-2-2 Band, Rear .......................................................................................................................................................57-3-2 Belting, Front ....................................................................................................................................................57-3-1 Belting, Rear ....................................................................................................................................................57-3-1 Base Assembly ................................................................................................................................................ 57-1-1 Blades & Blade Holders ...................................................................................................................................57-2-1 Clevis, Tongue ..................................................................................................................................................57-6-1 Cylinder, Hydraulic............................................................................................................................................57-8-1 Decals ......................................................................................................................................See Base Assemblies Deck Weldments ......................................................................................................................See Base Assemblies Driveshafts, Pull Models ......................................................................................................................57-5-3, 57-5-7 Lift & Semi-Mount ........................................................................................................................57-5-5 Jackshaft (All Pull Models) ..........................................................................................................57-5-4 Cross Shafts ................................................................................................................................57-5-2 Center Shaft ................................................................................................................................57-5-1 Gearbox, Assemblies .....................................................................................................................57-4-1 thru 57-4-3 3 Pt. Lift Hitch....................................................................................................................................................57-7-1 Semi-Mount Hitch .............................................................................................................................................57-7-1 Pull Type (Tongue) ...........................................................................................................................................57-6-1 Holder, Hose .....................................................................................................................................................57-8-2 Hub, Wheel (Pull Models) .................................................................................................................................57-6-2 Hub, Wheel (Lift & Semi-Mount) ...................................................................................................................... 57-7-2 Hydraulic, Components ........................................................................................................................57-8-1, 57-8-2 Light Assembly..................................................................................................................................................57-2-4 Ratchet Assy.....................................................................................................................................................57-8-2 Pillow Block Bearing & Mount ...........................................................................................................................57-5-6 Rims..................................................................................................................................................................57-6-3 Shields, Safety ..................................................................................................................................................57-3-3 Shredder Parts..................................................................................................................................................57-2-3 Skids.........................................................................................................................................See Base Assemblies Stop Kits (Hydraulic Cylinder) ...........................................................................................................................57-8-2 Tailwheels 3 Pt. Lift & Semi-Mount .................................................................................................................. 57-7-2 Tires......................................................................................................................................................57-6-3, 57-7-2
APRIL, 2008
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
39
23 39 23 39 23
18 37
12 13 23
32
8 6
39
33 34 20 11 10 14 15 16 17
4
28
38
9 38 35
23 39
30 33 7
36
20 31
29 27
9 10 25
24
2
23
22
1
26
19
17 15 16
38 37
14 15 16 17
14 21
5
3
4214 BASE & RELATED PARTS REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
PART NO. 96244 50031221 50040394 50040393 50040391 95290 44250 20100 15821 19502 15908 –––– 88983 44928 –––– –––– –––– 96246 96245 69877 69878
QTY. 1 1 1 1 2 2 2 2 4 4 2 2 1 10 10 10 10 1 1 1 2
REF. NO. 21 Base Weldment w/ Decals 22 Axle w/ Decals 23 L.H. Skid 24 R.H. Skid 25 Skid 26 Bushing (inner) Capscrew 1” x 10-1/2” Gr.5 (Outside) 27 28 Capscrew 1” x 9-1/2” Gr.5 (Inside) 29 Lockwasher 1” Hex Nut 1” 30 Flatwasher 1” 31 Roll Pin 1/4” x 1-3/4” 32 Cylinder Pin 33 Plow Bolt 3/8” x 1-1/2” 34 Lockwasher 3/8” 35 Flatwasher 3/8” 36 Hex Nut 3/8” Complete Decal Kit (18-23, 37-39) 37 Model No. Decal 38 Blade Rotation Decal C.W. 39 Blade Rotation Decal C.C.W. DESCRIPTION
57-1-1
PART NO. 50061049 50031212 50031214 90610 20414 44262 44338 44308 44099 96275 95690 87279 87293 1273 95696 95693 90108 50029417 50029418 50029419 50031219
QTY. 2 2 7 3 18 18 2 2 2 1 1 1 1 5 1 1 2 1 1 1 5
DESCRIPTION Bush Hog Decal Amber Reflector Red Reflector Reinforcing Pad Locknut Flanged 5/8” Capscrew 5/8” x 2-1/2” Gr.5 Capscrew M16 x 2 x 35 Flatwasher M16 Lockwasher M16 Transport Lock Assembly (30-36) Transport Bar Pin (Short) Pin (Long) Presto Pin Bar Weldment Pin Bushing (outer) Sheet Decal, 540 RPM Sheet Decal, 1000 RPM Sheet Decal Red/Orange Fluorescent Tape
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
2 3
5
1
2 3 7 4
1
4
5
6
6 5
2 3
1 8
4214 BLADE & BLADE HOLDERS REF. NO. 1 2 3 4 5 6 7 8
PART NO. 63607 252 20322 7919 66501 90243 86664 86665
QTY. 6 6 6 6 3 2 4 2
4
DESCRIPTION Blade Bolt Kit Jamnut 1-1/8” Lockwasher 1-1/8” Blade Bolt Blade Pan Weldment Blade Bar Weldment Blade CCW Rotation R.H. & Center Blade CW Rotation L.H.
57-2-1
6
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
5
8
2
11
65
10
6 5 8
56
12
6
6 5 8
7 6
7
5
11 7
10 11
7
10 6
4
6 5
6 5 8
6 5 10
6 5 8
10
6 5 8
13
5 8
11
7
1
11
10
6 5
10 8
3
10 7
11
9 5 6
5 6
5 6
96269 GRASS BAFFLE KIT PART NO. 95643 95645 95646 95644 –––– –––– –––– 88779 95647 88780 5161612 5161614 5161620
QTY. 1 1 1 1 27 27 9 9 1 8 14 2 2
57-2-2
6 5 7
7
REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13
6 5 8
DESCRIPTION Baffle, L. Rear Right Baffle Left Baffle Center Baffle Lockwasher 1/2” Hex Nut 1/2” Capscrew 1/2” x 1-1/4” Mounting Plate Mounting Bracket Mounting Bracket Carriage Bolt 1/2” x 1-1/4” Carriage Bolt 1/2” x 1-1/2” Carriage Bolt 1/2” x 2”
11
7
SEPTEMBER, 1998
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
5 14
14 13
14 13 5
14 13 5
23
24 2 3 14 13 5
10
8
17 16 9
6
16 17 15 17 16 9
11
1
15
23
8
7 16
19 21 20
13 5 17 16 9
7
17
7
3
15 3
17 16
12
21
12 3
4
6 4
22
12
3
18 10
See Blades & Blade Holders for these parts.
96266 SHREDDER ATTACHMENT 38” & 40” ROWS REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12
PART NO. 95643 96297 60032 86666 84342 91138 91106 88780 88779 20118 95647 44463
QTY. 1 1 5 6 5 2 3 2 3 4 1 6
96284 Rear Hitch Assembly
REF. NO. 13 14 15 16 17 18 19 20 21 22 23 24
DESCRIPTION Left Baffle Right Baffle Stationary Blade Double Edge Blade Support Plate Blade Mount, Short Blade Mount, Long Mounting Bracket Mounting Plate Capscrew 5/8” x 7” Gr. 5 Mounting Bracket Capscrew 5/8” x 10” Gr.5
57-2-3
PART NO. 19486 9162000 –––– –––– –––– 90612 44383 86310 15473 90613 5161612 5161614
QTY. 10 10 3 9 9 6 6 6 6 1 4 2
DESCRIPTION Lockwasher 5/8” Locknut 5/8” Capscrew 1/2” x 1-1/4” Lockwasher 1/2” Hex Nut 1/2” Blade Bolt Slotted Nut 1-1/8” Pivot Bushing Cotter Pin 1/4” x 2-1/2” Blade Bolt Kit Carriage Bolt 1/2” x 1-1/4” Carriage Bolt 1/2” x 1-1/2”
JULY, 2002
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
2
3
16
7 15
8 Existing Locknuts 18
1
17 14
4 13 LEFT
12
50033782 LIGHT ASSEMBLY
11
For Model 4214 REF. NO.
PART NO.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
50031969 50033783 50033784 50033785 50033786 50033787 –––– 44566 50033788 50033789 4140606 44520 –––– 50031961 50031964 20325 46610956 449
2 2 2 1 1 1 16 16 8 6 6 6 4 2 2 4 2 2
10
DESCRIPTION Lighting Assembly (Ref. #1, 14-18) Light, Amber Light, Red Harness, Wishbone Harness Light Module Capscrew 1/4” x 1-1/4” Hex Nut 1/4” Nylock Tie Wrap, Stainless J-Clip Screw #10 x 3/4” Locknut #10 Capscrew 5/8” x 3” Light Mount Weldment Lighting Weldment Roll Pin Spring Grease Fitting
57-2-4
9
6
5
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
3
2
4
1 6
10 12
8
11 5
10 9
96263 FRONT BELTING BUNDLE REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
PART NO. –––– –––– –––– –––– 96264 95653 95652 95651 95650 –––– –––– –––– –––– –––– 15602 87557
QTY. 10 10 10 10 1 1 1 1 2 20 44 20 20 2 2 4
DESCRIPTION Capscrew 1/2” x 5” Gr.5 Flatwasher 1/2” Lockwasher 1/2” Hex Nut 1/2” Front Belting Assembly Left Belt Mount Right Belt Mount Front Belt Belt Cover Capscrew 5/16” x 1-1/4” Gr.5 Flatwasher 5/16” Lockwasher 5/16” Hex Nut 5/16” Capscrew 5/16” x 2-1/2” Gr.5 Locknut 5/16” Chain, 7 Link
13
8
14
15 7
2 1
5
3
6
2
7
7 6 5
96280 REAR BELTING BUNDLE REF. NO. 1 2 3 4 5 6 7
PART NO. 96279 91257 –––– –––– –––– –––– ––––
QTY. 1 2 9 8 17 17 17
DESCRIPTION
7
Center Rear Belt Side Rear Belt Capscrew 1/2” x 1-1/4” (Center & End) Capscrew 1/2” x 3-1/4” (Side) Flatwasher 1/2” Lockwasher 1/2” Hex Nut 1/2” 57-3-1
6 5
3
4
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
4 2 9 1
7
8
2 6 10
9 8 7 6
5
7
3
7
96265 REAR BAND BUNDLE REF. NO. 1 2 3 4 5 6 7 8 9 10
PART NO. 95712 91148 91149 91150 –––– –––– –––– –––– –––– 96286
QTY. 1 2 1 1 10 13 29 23 23 2
DESCRIPTION Center Rear Band Rear Band Left Hand Rear Band Right Hand Rear Band Capscrew 1/2” x 1-1/4” Gr. 5 Capscrew 1/2” x 3-1/4” Gr.5 Flatwasher 1/2” Lockwasher 1/2” Hex Nut 1/2” Gusset
57-3-2
8
9
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
7 11
6
5 18 13
8 18
19
5
15
6
16 17 2
14
7 6
12 20
23 10 2
3 24
5
21 18
3
18
5
1
6 7 7
4
6
6
5
22
8
9
DRIVELINE SHIELDING REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
PART NO. 88100 –––– –––– 81592 90560 44311 44216 95722 95727 95728 95734 95732 91157 93306 44338 44099 44308 20312 95711 95710 95736 44299 –––– ––––
QTY. 1 4 4 1 20 24 16 2 2 2 1 1 1 1 2 2 2 4 1 1 2 4 2 2
DESCRIPTION Bearing Shield (Pull Models Only) Capscrew 1/2” x 1-1/2” Lockwasher 1/2” Input Shield Capscrew M8 x 1.25 x 15 Lockwasher M8 Flatwasher M8 Shield Weldment Bracket Weldment, L.H. Wing Bracket Weldment, L.H. Center Bracket Weldment, R.H. Wing Bracket Weldment, R.H. Center Mount (Rear) Mount (Front) Capscrew M16 x 2 x 35 Lockwasher M16 Flatwasher M16 Lynch Pin Shield Shield Mount Weldment Knob M8 x 1.25 x 25 3/8” Locknut Hex Nut 1/2”
57-3-3
JANUARY 2007
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
5 3
8
2 15
4
23
1 6
14
10 4
71 8
17
19
16
19
5 17
18
12 21
10
13
15
16
9
20
11
7 4 6 1 4
14
2
11
3
22 13
24
70837 DIVIDER GEARBOX ASSEMBLY Model: 4214 REF. NO.
PART NO.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
70873 70874 70875 70240 70876 70877 70878 70292 70879 70796 70881 70882 70190 70883 70571 70570 70888 70084 70374 70269 70884 70885 81572 70181
2 2 2 4 8 2 2 1 1 2 2 1 2 2 2 2 2 2 2 8 1 1 1 1
DESCRIPTION Extension Housing Shaft 1 3/8”-21 Spline Oil Seal 50 x 80 x 10 Bearing Bolt m12 x 25 Gr. 8.8 Snap Ring Shim Plug 3/8” Housing Bearing Snap Ring Input Shaft Oil Seal 45 x 85 x 10 Shim Cotter Pin B4 x 55 Nut M30 x 1.5 Gear 21 T (Output) Shim 51.5 Shim 30.3 Bolt m10 x 25 Gr. 8.8 Gear 21 T (Input) Cover Breather Plug Plug 3/8”
57-4-1
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
70542 GEARBOX ASSEMBLY CENTER & RIGHT SIDE MODEL 4214
REF. NO.
PART NO.
QTY.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
70122 70121 70256 70459 70304 70258 70302 70546 70795 70407 70586 70460 70800 70266 70507 70588 70575 70166 70077 70076 15473 70292 70115 70333 70334 70335 70336 70337 70338 70339 70340
1 1 1 1 2 1 8 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 A/R A/R A/R A/R A/R A/R A/R A/R
Cap Circlip, Internal Bearing Input Shaft Spring Pin Gear (18 Teeth) Screw, Allen Head M10 x 25 Vent Plug Bearing Top Housing Castle Nut Gear (18 Teeth) Bearing Gasket Lower Housing Lower Shaft (70542 Assy. Only) Dust Excluder Shoulder Ring Flatwasher Castle Nut M30 x 2 Cotter Pin 1/4 x 2-1/2” Plug Dust Cap Shim .3mm Thick Shim .4mm Thick Shim .5mm Thick Shim 1.0mm Thick Shim .3mm Thick Shim .4mm Thick Shim .5mm Thick Shim 1.0mm Thick
25
57-4-2
A/R - As Required
REF. NO.
PART NO.
QTY.
DESCRIPTION
26
70344 70345 70346 70347 70576 70585
A/R A/R A/R A/R 1 1
Shim .3mm Thick Shim .5mm Thick Shim 1.0mm Thick Shim .4mm Thick Protective Shield Cotter Pin
27 28
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
26
70832 GEARBOX ASSEMBLY LEFT HAND MODEL 4214
7
5 4
3
1
2
6 8 11
10
9 12 23
17 25
24 21
REF. NO.
PART NO.
QTY.
DESCRIPTION
1 2 3
70273 70240 70337 70338 70339 70340 70258 –––– 70480 70292 83049 70333 70334 70335 70336 70121 70145 70585 70891 70588 70077 70076 70586 70576 70166 70575 70159 70507 70304 70344 70345 70346 70347 70460 70546 15473 70266
1 1 A/R A/R A/R A/R 1 1 1 1 1 A/R A/R A/R A/R 1 1 1 8 1 1 1 1 1 1 1 2 1 2 A/R A/R A/R A/R 1 1 1 1
Casing Bearing Shim .3mm Shim .4mm Shim .5mm Shim 1.mm Gear 18 T Plate Shaft 21 Spline (Output) Plug Bearing Shim .3mm Shim .4mm Shim .5mm Shim 1.mm Snap Ring Oil Seal Cotter Pin B4 x 60 Bolt 12mm Shaft (Output) Washer Castle Nut M30 x 2 Castle Nut M40 x 1.5 Protective Washer Snap Ring Seal, Double Lip 50 x 90 x10 Bearing Extension Spring Pin Shim .3mm Shim .5mm Shim 1.mm Shim .4mm Gear 18 T (Output) Vent Plug Cotter Pin B60 x 60 Gasket
4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26 27 28
28
13
22
14
21 20 19 18 15 16 27
57-4-3
JUNE, 2004
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
1
6
2 10
8
7
2
3
3 4
20
11
5
16
12 13
14
15
5 14
17
18 5
4
19
9
76524 CENTER DRIVESHAFT Mfd. by Comer/EG REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
PART NO. 76365 76696 76783 44353 44244 76305 76537 76307 76300 63946 76080 76164 76082 76083 76064 76301 76085 76086 44155 44154
QTY. 1 2 2 8 8 1 1 1 1 1 8 1 1 2 1 1 1 1 8 8
DESCRIPTION Yoke w/ Grease Nipple Cross Bearing Kit Grease Nipple Capscrew M12 x 1.75 x 45 Hex Nut M12 x 1.75 Flanged Yoke, Male Retainer Washer Flanged Yoke Female Complete Disc Clutch Grease Nipple Spring Flanged Yoke Bushing Lining Ring Tapered Pin Set 1-3/8” Clutch Support Inner Plate Pressure Plate Capscrew M10 x 1.5 x 85 Lock Nut M10 x 1.5
57-5-1
JUNE, 2004
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
21 1 11
22 2
2 3
4
5
8
23
6
9 3
7
10 20 12
13
15
16
15
11
14
17
93068 WING DRIVESHAFT Mfd. by Comer/EG May substitute 91133 Driveshaft Mfd. by Bondioli & Pavesi REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
PART NO. 76310 64663 63956 66865 66866 50028399 92021 66869 66870 76300 76064 76080 76164 76082 76083 76301 76085 76086 44155 44342 76302 76303 78786
QTY. 1 2 2 1 1 1 1 1 1 1 2 8 1 1 2 1 2 1 8 8 1 1 1
DESCRIPTION Complete Yoke Cross Journal Set Grease Nipple Outer Yoke Roll Pin for Outer Tube Outer Tube Inner Tube Roll Pin for Inner Tube Inner Yoke Complete Disc Clutch Tapered Pin Set 1-3/8” Spring Flanged Yoke Bushing Lining Ring Clutch Support Inner Plate Pressure Plate Capscrew M10 x 1.5 x 85 Hex Nut M10 x 1.5 Half Female Shaft Half Male Shaft Danger Decal, Outer Tube
57-5-2
18
19
APRIL 2000
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
18
19
1
2
22 3
4
5
2 20
3
17
16
13 8
9
6 11
21
10
7
15
4
10
12
14
76233 C.V. DRIVESHAFT 1000 RPM – 1-3/8” – 21 Spline (Mfd. by Comer/EG) Replaced by 76624 Driveshaft (Mfd. by Comer/EG)
76571 C.V. DRIVESHAFT 1000 RPM – 1-3/4” – 20 Spline (Mfd. by Comer/EG) Replaced by 50024435 Driveshaft (Mfd. by Comer/EG) REF. PART NO. NO. QTY. 1 50017482 1 50017501 1 2 76420 2 3 63956 3 76579 2 4 76421 1 5 64663 1 76582 1 6 76422 1 7 76362 6 8 76423 1 9 76057 1 10 87992 6 11 76059 1 12 64814 3 13 76424 1
DESCRIPTION Complete Collar Yoke (76233) Complete Collar Yoke (76571) Cross Journal Set Grease Nipple (76233) Grease Nipple (76571) Wide Angle Double Yoke Cross Journal Set (76233) Cross Journal Set (76571) Complete Yoke Screw Bearing Ring Guard Retaining Collar, Outer Bolt Guard Retaining Collar, Inner Safety Chain Guard Cone Set
REF. NO. 14 15 16 17 18 19 20 21 22
57-5-3
PART NO. 76450 76599 76247 76451 76600 76452 76601 76453 76602 76454 76603 78786 78608 50017480 50017502
QTY. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DESCRIPTION Complete Shield w/ Instr.(76233) Complete Shield w/ Instr.(76571) Tapered Pin Set 1-3/4” Female Tube w/ Yoke and Lube (76233) Female Tube w/ Yoke and Lube (76571) Male Tube w/ Yoke and Lube (76233) Male Tube w/ Yoke and Lube (76571) Half Female Shaft w/ Shield (76233) Half Female Shaft w/ Shield (76571) Half Male Shaft w/ Shield (76233) Half Male Shaft w/ Shield (76571) Danger Decal, Outer Tube Danger Decal, Outer Shield Ball Collar Kit, 1-3/4” (76233) Ball Collar Kit, 1-3/4” (76571)
APRIL 2000
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
1
2
4
3
5
6 13
12
7
14
9
10 8
8 11
76526 JACKSHAFT 1000 RPM – 1-3/8” – 21 Spline Mfd. by Comer/EG 4214 Pull Models REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
PART NO. 76239 64963 63956 78134 67108 76538 76244 87992 76245 64814 76539 76247 78786 78608
QTY. 1 1 1 1 1 1 1 6 1 2 1 1 1 1
DESCRIPTION Complete Yoke Cross Bearing Kit Grease Nipple Outer Yoke Roll Pin for Outer Tube Outer Tube w/ Splined Shaft Guard Retaining Collar, Outer Bolt Guard Retaining Collar, Inner Safety Chain Complete Shield w/ Instr. Tapered Pin Set 1-3/4” Danger Decal, Outer Tube Danger Decal, Outer Shield
57-5-4
MAY, 2005
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
2
1
4
22
3
7
11
10
6
8
5 20
17
9
3 18
2
19
16 21
15 14
12 13
13
76527 DRIVESHAFT 4214 Lift & Semi-Mount Models 1000 RPM – 1-3/8” – 21 Spline Mfd. by Comer/EG
76528 DRIVESHAFT 4214 Lift & Semi-Mount Models 1000 RPM – 1-3/4” – 20 Spline Mfd. by Comer/EG
REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12
PART NO. 76805 76806 64963 63956 78134 67108 76274 76540 76545 76541 76546 67085 67086 76239 76244
QTY. 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1
DESCRIPTION Complete Collar Yoke (76527) Complete Collar Yoke (76528) Cross Bearing Kit Grease Nipple Outer Yoke Roll Pin for Outer Tube Bushing w/ Grease Fitting Outer Tube (76527) Outer Tube (76528) Inner Tube (76527) Inner Tube (76528) Roll Pin for Inner Tube Inner Yoke Complete Yoke Guard Retaining Collar, Outer
REF. NO. 13 14 15 16 17 18 19 20 21 22
57-5-5
PART NO. 87992 76245 64814 76542 76547 76247 76543 76548 76544 76549 78786 78608 87967 ––––
QTY. 6 1 2 1 1 1 1 1 1 1 1 1 1 1
DESCRIPTION Bolt Guard Retaining Collar, Inner Safety Chain Complete Shield w/ Instr. (76527) Complete Shield w/ Instr. (76528) Tapered Pin Set 1-3/4” Half Female Shaft w/ Shield (76527) Half Female Shaft w/ Shield (76528) Half Male Shaft w/ Shield (76527) Half Male Shaft w/ Shield (76528) Danger Decal, Outer Tube Danger Decal, Outer Shield Ball Collar Kit 1-3/8” (76527) Ball Collar Kit 1-3/4” (76528)
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
4 7
2
12
13
15 16 14
17 13
9
1
3
5 6
PILLOW BLOCK BEARING & MOUNT For all Pull Models 4214 Series 10 REF. NO.
PART NO.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
91158 88100 90356 –––– –––– 9162400 –––– 20763 20237 19486 9162000 90986 88916 77492 77491 88840 90983
1 1 1 2 1 1 2 2 2 4 4 1 2 1 1 1 1
8
DESCRIPTION
11 Mount Weld. Shield Weld. Pin Weld. Capscrew 1/2” x 1 1/4” Gr.5 Lockwasher 3/4” Locknut 3/4” Lockwasher 1/2” Capscrew 5/8” x 5” Gr.5 Capscrew 5/8” x 4” Gr.5 Lockwasher 5/8” Locknut 5/8” Pillow Block Bearing Bushing, Tension Snap Ring Bearing w/ Collar Set Screw Spacer
10
57-5-6
11
APRIL, 2003
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
23
22 1 27
2
2
4
5
3
3
10
9 6
8 26 24
19 7
3
21
20 17
11
12
13
15
25
14
16
14
18
50024435 C.V. DRIVESHAFT ASSEMBLY
76624 C.V. DRIVESHAFT ASSEMBLY
1000 RPM – 1-3/4” – 20 Spline Manufactured by Comer / EG ASAE Size 4 Used on 4214 Pull Models Replaces 76571 Driveshaft
1000 RPM – 1-3/8” – 21 Spline Manufactured by Comer / EG ASAE Size 4 Used on 4214 Pull Models Replaces 76233 Driveshaft REF. NO.
PART NO.
QTY.
1
50017482 50017501 76420 76579 76421 76893 66866 76894 76901 76900 64663 76422 76362 76423 76057 87992 76059
1 1 2 3 1 1 1 1 1 1 1 1 6 1 1 6 1
2 3 4 5 6 7 8 9 10 11 12 13 14 15
DESCRIPTION Complete Collar Yoke (76624) Complete Collar Yoke (50024435) Cross Journal Set Grease Nipple Wide Angle Double Yoke Outer Yoke Roll Pin for Outer Tube Wiper Outer Tube w/ Decal (76624) Outer Tube w/ Decal (50024435) Cross Journal Set Complete Yoke Screw Kit Bearing Ring Collar, Outer Tube Bolt Collar, Inner Tube
REF. NO.
PART NO.
QTY.
16 17 18
64814 76933 76948 76957 76247 76681 76682 76949
3 1 1 1 1 1 1 1
76958
1
76684 78786 78608 76892 50017480 50017502
1 1 1 1 1 1
19 20 21 22
23 24 25 26 27
57-5-7
DESCRIPTION Safety Chain Guard Cone Set Complete Shield (76624) Complete Shield (50024435) Tapered Pin Set 1-3/4” Female Tube w/ Yoke & Lube Male Tube w/ Yoke & Lube Half Female Shaft w/ Shield (76624) Half Female Shaft w/ Shield (50024435) Half Male Shaft w/ Shield Danger Decal, Outer Tube Danger Decal, Outer Shield Plastic Cap, Outer Tube Ball Collar Kit 1-3/8” (76624) Ball Collar Kit 1-3/4” (50024435)
SEPTEMBER, 1998
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
5
9 7 9
4
1
13 12
3 6
2 11
9
7
16 10
19
9
17 20
18 24
23
11
21
15 14 21 20
22
26
25
TONGUE & RELATED PARTS For 4214 REF. NO.
PART NO.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
20503 9163200 94117 50017295 87510 92309 449 87279 –––– 92314 20376 50017296 15612 90585 87340 87317 92969 92977 86356 –––– –––– 92973 –––– 20325 92970 24D25128
2 2 2 2 1 1 2 1 4 1 2 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1
DESCRIPTION Capscrew 1” x 8 1/2” Gr.5 Locknut 1” Tongue Bushing Level Rod Assy. Clevis Assy. R.H. Thread Clevis Assy. L.H. Thread Grease Zerk Clevis Pin Cotter Pin 3/16” x 1 1/2” Pin Flatwasher 1” Rod Jamnut Tongue Weldment Important Decal Important Decal Hitch Assembly Hitch Weldment Collar, Clevis Pin Capscrew 5/8” x 3-3/4” Gr.5 Locknut 5/8” Clevis Weldment Flatwasher 1-1/4” Roll Pin 1/4” x 1-3/4” Pin Weldment Jackstand
57-6-1
8
JUNE, 2004
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
28 12 9
11
30
33 10
15
1 2
3
31
8
14 35
32
4
23 16
22
21 29
5 34
7
6
36 30 28
13
AXLE ARM ASSEMBLIES
24
For 4214 Pull Models REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
PART NO. 98774 95677 98776 95689 20766 –––– –––– 96322 21020430 50035301 91152 44524 20150 91261 77611 67379 121 120 119 50073 50076 7967 296 7977 7965 15515 15445 449 88921 –––– –––– –––– 20326 20376 50031212 14-6-197 14-6-198
QTY. 1 1 2 1 4 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 5 5 2 1 2 2 2 2 1 2 1 1
DESCRIPTION Axle Arm w/ Decals Axle Arm Weldment Anchor Bar Pin 3/4” x 7-1/2” Gr.5 Lockwasher 3/4” Hex Nut 3/4” Collar Cotter Pin 1/8” x 3” Spring Spring Cup Locknut 1”, Flanged Capscrew 1” x 8-1/2” Rubber Cushion Spindle (Dual Wheel) Spindle (Single Wheel) Hub Cap Slotted Nut Flatwasher Outer Bearing Cone Inner Bearing Cone Seal Cotter Pin 1/8” x 1-1/2” Hub Assy. Hub Casting Nut 1/2” – 20 UNF Lug Bolt 1/2” – 20 UNF Grease Fitting Bearing Repair Kit Capscrew 1/2” x 3-1/4” Gr.5 Lockwasher 1/2” Hex Nut 1/2” Roll Pin 3/8” x 2” Flatwasher 1” Amber Reflector Bearing Cup Bearing Cup
57-6-2
20 25 26 37
19 18 17
JULY, 2002
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
WHEELS & TIRES For 4214 Pull Models
77 AUTO RIM 5 HOLE 15”
2 3 4
1
294 SOLID TIRE ASSEMBLY 2
5
57-6-3
REF. NO.
PART NO.
QTY.
1 2 3 4 5
116 117 15597 –––– 20126
1 2 5 5 5
DESCRIPTION Solid Tire Wheel Flange Nut 3/8” UNF Lockwasher 3/8” Bolt 3/8” x 1” UNF
AUGUST, 1996
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
2 17
11
14 13
16 15
5
10
11
3
10
18
4
8 1 12
9 7
6
REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
3 PT LIFT HITCH
SEMI MOUNT HITCH
For 4214 Lift Models
For 4214 Semi-Mount Models
PART NO. 90317 91154 95263 90213 90212 25G12545 20558 19061 20232 15821 19502 20187 15908 9163200 20264 —— —— 95261
QTY. 1 1 1 1 1 2 2 1 2 3 3 2 2 2 1 1 1 2
DESCRIPTION
REF. NO.
PART NO.
QTY.
6 7
25G12545 20558
2 2
Mast Weldment Slide Tube Weld. Mast Link Weld. A-Frame Top Bushing 1” Mast Top Bushing 3/4” Hitch Pin Lynch Pin Capscrew 1” x 5” Gr. 5 Capscrew 1” x 2-1/2” Gr. 5 Lockwasher 1” Hex Nut 1” Capscrew 1” x 10” Flatwasher 1” Locknut 1” Capscrew 3/4” x 4-1/2” Gr. 5 Lockwasher Hex Nut Bushing
57-7-1
DESCRIPTION Hitch Pin Lynch Pin
JULY, 2002
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
4
33
3
32 36
34 1
12 19
9
36 6
10
35
5
2 11 7 38
18
17
21 29 20
14
13
27 28 30
37
8
21
23 24
15
22 31
16
25 26
TAILWHEEL ASSEMBLY For 4214 Lift & Semi-Mount REF. NO.
PART NO.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
91216 81464 81467 52732 98774 15521 1620 20150 91152 50035301 91261 44524 95686 20766 —— —— 95689 96322 21020430 1596
1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 4 1 1 1 1
DESCRIPTION
REF. NO.
PART NO.
QTY.
21 22 23 24
18141206 1595 7967 14-6-197 50076 14-6-242 14-6-241 7968 1613 449 15515 15445 1612 294 15597 —— 20126 117 20376 50031212
2 1 1 1 1 1 1 1 1 1 5 5 1 1 5 5 5 2 1 1
Caster Arm Caster Fork Weld. Spacer Roll Pin 1/2” x 3” Axle Arm Mount w/ Decal Locknut 1-1/4” Collar Lock Spindle Capscrew 1” x 8-1/2” Spring Cup Spring Rubber Cushion Locknut 1”, Flanged Plate Capscrew 3/4” x 7-1/2” Gr.5 Lockwasher 3/4” Hex Nut 3/4” Axle Arm Pin Collar Cotter Pin 1/8” x 3” Small Spacer
25 26 27 28 29 30 31 32 33 34 35 36 37 38
57-7-2
DESCRIPTION Set Screw 3/8” x 3/4” Large Spacer Seal Triple Lip Bearing Cup Bearing Cone Bearing Cup Bearing Cone Seal (Triple Lip) Hub Assy. w/ Bearing Cups Grease Fitting Lug Nut Lug Bolt Hub Casting Solid Tire Nut 3/8” UNF Lockwasher 3/8” Bolt 3/8” x 1” Wheel Flange Flatwasher 1” Amber Reflector
APRIL, 2008
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
8
1
7
12
13
3 Cylinder Assembly Part Number Stamped Here.
15
6
5
14
2 1 2
4 16 10
8
11 9 7
99565 HYDRAULIC CYLINDER (Was Part No. 95394) Mfd. by Monarch 3.5” Bore x 8” Stroke 1.25 Rod Dia. 3/4” – 16 ORB Ports Replaced by 50047475 (Bailey) REF. NO.
PART NO.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
95429 92430 50017993 95431 95426 95427 95425 21020614 95433 95428 95422 95420 95421 95435 95423 50017623
1 1 1 1 1 4 2 4 1 1 1 8 1 1 1 1
DESCRIPTION Clevis Cap Rod Cap Piston Rod 1.25” Dia. Cylinder Tube Tie Rod Pin 1” Dia. Cotter Pin 3/16” x 1 1/2” Thread Lock Rod Clevis 1.25” x 1” Set Screw 3/8” x 1/2 Knurled Hex Nut 5/8” UNF Hex Nut 1”-14 Plug 3/4” Caution Decal Seal Kit
57-8-1
APRIL, 2008
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
12 1 8
7 13
3
15
Cylinder Assembly Part Number Stamped Here. 6
14
5 2 12
16
4 11 10 9
8
50047475 HYDRAULIC CYLINDER Mfd. by Bailey 3.50” Bore x 1.25” Rod Dia. x 8.00 Stroke
REF. NO.
PART NO.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
–––– –––– –––– –––– –––– –––– –––– –––– –––– –––– –––– –––– –––– –––– –––– 50017623
1 1 1 1 1 4 2 4 1 1 1 4 1 3 1 1
DESCRIPTION End Clevis Gland Piston Piston Rod Cylinder Tube Tie Rod Clevis Pin Cotter Pin Rod Clevis Bolt Rod Clevis Rod Clevis Nut Tie Rod Nut Piston Nut Steel Plug w/ O-Ring Warning Decal Seal Kit
57-8-2
7
APRIL, 2008
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
3
1817 RATCHET ASSEMBLY
2 4
2
REF. NO. 1 2 3 4
2 1
2
PART NO. 50028265 50028264 11810 15474
QTY. 2 4 1 1
DESCRIPTION Pin Clip Pin Handle Cotter Pin
1
12032 HOSE HOLDER ASSY. REF. NO.
PART NO.
QTY.
1 2 3 4
–––– –––– –––– 12031
1 1 1 1
HYDRAULIC HOSES & FITTINGS
REF. NO.
PART NO.
QTY.
1 2 3 4 5
53340 24-6-434 14-40-98 50047240 62427
1 1 1 1 1
DESCRIPTION Adaptor 9/16” JIC to 3/4” SAE Adaptor 9/16” JIC to 1/2” NPT 90° Elbow 3/4” ORB to 9/16” JIC Breather Plug Hydraulic Hose 144”
63451 STOP COLLAR KIT
57-8-3
DESCRIPTION Flatwasher 5/8” Capscrew 5/8” x 2” Hex Nut 5/8” Hose Holder Rod
2501 Griffin Ave. • Selma, AL 36703 (334) 872-6261 • (334) 874-2700 Parts Ordering 1-800-304-2836 Fax 1-800-572-1784 www.bushhog.com
