Transcript
C61
P
R
4 IR Emitter or Selectable Blaster Outputs; Amplified Infrared Connecting Block With IR Receiver Connection O
D
U
C
T
I
N
F
O
R
M
A
T
I
O
N
A
Product Overview The C61 is a connecting block device for connecting IR receivers, IR emitters and a power supply. This central control unit features an amplifier circuit for driving up to 4 IR emitters and/or up to 2 high output IR blasters (any combination of 4 total). A 4/P connector and a 3.5mm Quad mini-jack make for easy connection of IR receivers.
N
D
I
N
S
T
A
L
L
A
T
I
O
N
G
U
System Diagram 1: DC12V
RT34.1
DC12V 200mA
+12V GND ST OUT IR IN
A/V RECEIVER VOLUME TUNE SEARCH
FM CENTER STEREO TUNE
TUNE
MODE
STORE
PRESET
PHONES
EXTRA SPEAKERS
BASS
TREBLE
BALANCE TAPE 1 MONITOR
VIDEO
TAPE 2
VCR
LD
AUX
CD
AM
MONO
FM
CD PLAYER Compact Disc Player
MIN
SEC
PLAY PAUSE
STOP
RANDOM
SKIP
OPEN
TIME
REPEAT
SCAN
6 7 8 9 10
Product Specifications IR Receiver Connections: Connect the IR receiver to the 4/position connector marked V+ (12VDC), G (GND), ST (Status) and IR (Signal). Note: Select receivers do not offer ST. A 2nd IR receiver connection is available via the Jack marked “IR RCVR”. Please refer below for the proper connections. IR Emitter and/or Blaster Outputs: “See diagram 3”. This central control unit features an amplifier circuit for driving up to 4 IR emitters and/or up to 2 high output IR blasters (any combination of 4 total). Either Single and/or Dual IR emitters, connect up to 4 emitters to the emitter jacks marked 1-4. Place the emitters on the source equipment, up to 8 sources available. When connecting the BP10 Blaster only plug them into the jacks appropriately marked and move the switch to the ON position to activate the Blaster output circuitry. Net On: The NET ON position should be selected when using longer lengths of cable (over 50 feet shielded in particular) between the IR receiver, Keypad, etc. and the C61. This ensures better performance for the IR signal. If you are using two or more C61’s, be sure ONLY ONE of C61’s is in the “NET ON” position. “See diagram 2” Power: At minimum, connect a Regulated 12VDC/500mA power adaptor for System #1, yet use a Regulated 12VDC/1.2A power adaptor for System Diagrams #2 and #3. Status Power: A 12VDC/200mA “2.1mm + tip –sleeve”. Connecting a power supply to this connection will power the status connection. The green LED will illuminate when powered. This can be from a 12V trigger output or from a wall type power supply plugged into a switched outlet of a stereo receiver. Note: Not all IR Receivers feature ST (Status) capability.
D
Mounting: Install the C61 near the source equipment that the emitters are attached to. The C61 can be mounted with double stick tape, cable ties, etc.
Product Features 1. The C61 has built-in amplifier circuit for driving up to 4 IR emitters and /or up to 2 high output IR blasters (any combination of 4 total). 2. Two separate connections are available for IR Receivers: Input 1: Uses a 3.5mm Quad minijack; Input 2: Uses a 4/position connector: “V+ (12VDC), G (Ground), ST (Status) and IR (Signal)” Refer to the diagram below for connection. Some IR receivers do not have ST. 3. The “ST OUT” provides status power from 12V trigger output or wall type power supply plugged into the switched output of an A/V receiver. 4 The C61 cable extension distance can provide up to 300M lengths of wire between IR set to C61 system. When switching to “NET ON”, the C61 cable extension distance increases up to 400M lengths from IR set to C61 5. NET Amp circuits provide better performance for high data rate of IR codes.
I
DVD PLAYER
RS31.1
V+: BLACK WITH GREY SOLID STRIPE G: BLACK BACK VIEW FOR CODING & DEFINITION REMOTE CONTROL IR: BLACK WITH GREY DASHED STRIPE
E
C61
P
R
4 IR Emitter or Selectable Blaster Outputs; Amplified Infrared Connecting Block With IR Receiver Connection O
D
U
C
T
I
N
F
O
R
M
A
T
I
O
N
A
N
D
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
System Diagram 2: IR STATUS GND +12V
TO ADDITIONAL C61 OR OTHER ROOMS IF NEEDED
DC12V 1,2A DC12V 200mA
TO ADDITIONAL C61 OR OTHER ROOMS IF NEEDED RT34.1
NOTE: DO NOT CONNECT A POWER SUPPLY TO THIS OR OTHER SUBSEQUENT C61 ON THE NETWORK.
A/V RECEIVER
A/V RECEIVER VOLUME
VOLUME
TUNE
TUNE
SEARCH
FM CENTER STEREO TUNE
TUNE
SEARCH
FM CENTER STEREO TUNE MODE
TUNE
STORE
PRESET
EXTRA SPEAKERS
PHONES
BASS
BALANCE
TREBLE
TAPE 1 MONITOR
VCR
LD
AUX
CD
AM
MONO
FM
PHONES
EXTRA SPEAKERS
BASS
TREBLE
CD PLAYER Compact Disc Player
MIN
SEC
MODE
STORE
PRESET
VIDEO
TAPE 2
BALANCE TAPE 1 MONITOR
VIDEO
TAPE 2
VCR
LD
AUX
CD
AM
MONO
FM
CD PLAYER PLAY PAUSE
STOP
RANDOM
SKIP
OPEN
TIME
REPEAT
SCAN
Compact Disc Player
MIN
6 7 8 9 10
DVD PLAYER
SEC
PLAY PAUSE
STOP
RANDOM
SKIP
OPEN
TIME
REPEAT
SCAN
6 7 8 9 10
DVD PLAYER RW32.1
System Diagram 3: IR STATUS GND +12V
DC12V 1,2A DC12V 200mA
SHELF
IR: YELLOW STATUS: PURPLE GND: BLUE +12V: ORANGE
RECEIVER SIDE VIEW
STATUS
IR SIGNAL
RS31.1
GROUND
DVD PLAYER SIDE VIEW VOLUME TUNE SEARCH
FM CENTER STEREO TUNE
TUNE
MODE
STORE
PRESET
PHONES
EXTRA SPEAKERS
BASS
TREBLE
BALANCE TAPE 1 MONITOR
VIDEO
TAPE 2
VCR
LD
AUX
CD
DVD PLAYER
AM
FM
MONO
SHELF VCR SIDE VIEW
2 METERS / 78 INCHES
SHELF A/V RECEIVER
RT34.1
12 VDC
BP10
V+: BLACK WITH GREY SOLID STRIPE G: BLACK
SHELF SAT DECODER SIDE VIEW
RW32.1
BP10
SHELF RB33.1
RT34.1
BACK VIEW FOR CODING & DEFINITION
In North America contact: Trends Electronics International Inc. - 100 – 980 West 1st Street. North Vancouver, B.C. V7P 3N4 Phone: 1 (877) 946-9255 Fax: 1 (800) 618-7363 Email:
[email protected]
IR: BLACK WITH GREY DASHED STRIPE
E
