Transcript
Issue N°4 • April 2008
Cable Load Limiters
Fieldbus Coupler
in stainless steel
transferring large amounts of data
The cable tension sensor of the type SK-02, based on strain gauges technology, is the sensor for a quick installation without mechanical modification of the existing installation. Produced totally in stainless steel, the sensor is adapted to cables with a diameter from 8 to 22mm, and connected to an amplifier type LMU, is the essential element for the overload controlling of cranes or other lifting installations. Designed for the withstanding of long-term dynamic requests, it represents as well an excellent alternative when being used in difficult environments. Declined in several versions from 10 to 100kN, this transducer offers a large overload capacity.
The coupler supports up to 64 I/O terminals, or even 250 via a bus extension. Its application interface is based on the CANopen communication profile DS 301. Powerlink's key benefit is that it is both based on standard Ethernet and meets extreme demands on deterministic performance and cycle times. The protocol is therefore suited for use in applications with hard real-time requirements, but also for reliably transferring large amounts of data within a given span of time. It features a flexible, application interface that gives users access to a broad base of existing device and application profiles. This I/O System 750 provides an industry-grade hardware base for Powerlink.
MAGTROL Tel. +41-26-4073000 Fax +41-26-4073001
WAGO Tel. +49-571-8870 Fax +49-571-887169
Enter 22697 at www.tim-info.com/ien
Relief Valve
with graded text display
PED-certified
The Logo! logic modules of the 0BA6 series are suitable for universal use in industry and in building systems. The new text display has four lines with twelve characters each. Fifty different four-line messages can be configured, with expanded display options. Up to 32 characters per line can be stored. The new logic modules and the internal and external display are configured with the Logo! Soft Comfort V6 standard software. New function blocks for arithmetic and pulse width modulation expand the application options.
Designated HPRV, this valve is available with 3.6mm flow ports. At the heart of the valve is a captured seat design that is blow-out and chip-resistant and works across the entire operating pressure range. A range of colourcoded springs configure the valve for eight pressure ranges from 10.3-24.1 to 345-414 bar. Fine adjustment can be achieved by the end user by means of an external nut, which is secured in position by Parker's Tru-Loc mechanism and a lock wire to eliminate the possibility of accidental movement and guard against tampering.
SIEMENS A&D Tel. +49-911-9783273 Fax +49-911-9783321
PARKER HANNIFIN Tel. +44-1271-313131 Fax +44-1271-373636
PIR movement detectors 10 A. A range of compact and reliable products; The only ones with IMQ approval.
Type 18.21 PIR movement detector for internal installations
Prodotto conforme alle norme CEI di sicurezza sotto controllo permanente dell’IMQ
Type 18.01 for internal Installations. Wall mounting
Type 18.11 for external installations (IP 54). Wall mounting
Type 18.31 for internal Installations. Recessed mounting Type 18.21 for internal Installations. Surface mounting
For SLI: enter 22267 at www.tim-info.com/ien
Enter 23068 at www.tim-info.com/ien
Failure Controller
Digital Camera
monitoring 3 phases of the mains
actively cooled, high resolution
The AMF3.0 automatic mains failure unit is a microprocessor based digital unit monitoring the 3 phases of the mains. The device controls the changeover of mains and generator contactors if a mains failure occurs. The module is able to display all the parameters which are essential for the basic gen-set control. It has 3 operation modes: Stop, Test and Auto. The operation modes can be chosen via the pushbuttons mounted on the front panel. The module can be adapted to all of the generators without the need of any other unit or module, by adjusting the parameters.
The MegaPlus EC16000 is an actively cooled, high resolution 16 megapixel digital camera. It is uniquely designed to separate and isolate the camera’s primary electronics from the sensor cooling path resulting in true 12-bits per pixel at virtually any operating temperature. Using Peltier cooling, both dark noise and thermal drift are significantly reduced. The EC16000 is designed to cool the sensor to 5°C below ambient temperature without a fan. An optional fan provides cooling capability to ~12 °C below ambient temperature.
EN-KO ELECTRONICS Tel. +90-232-3767806 Fax +90-232-3767792
FRAMOS Tel. +49-89 -71066713 Fax +49-89 -71066766
Enter 23354 at www.tim-info.com/ien
Finder 18 Series. The hidden watcher
Enter 23222 at www.tim-info.com/ien
Logic Modules
Enter 23101 at www.tim-info.com/ien
19
Enter 22247 at www.tim-info.com/ien For SLI: enter 20388 at www.tim-info.com/ien
The power in relays and timers since 1954
MADE IN ITALY
ISO 9001:2000
on-line catalogue www.findernet.com
ISO 14001:2004
