Transcript
Car-Pro
®
by:
CPX-2600 PROFESSIONAL VEHICLE SECURITY SYSTEM
INSTALLATION MANUAL (For Authorized Dealers Only)
THIS PRODUCT IS DESIGNED FOR PROFESIONAL INSTALLATION ONLY
WIRING DIAGRAM
H6: 4 Pin White Connector For Shock Sensor
H1: Main 5 Pin White harness H2: 6 Pin White Mini Connector
H3 H7: Black Antenna Wire
H3/1 Blue Wire: (-) 200mA Unlock Pulse, (+) 200mA Lock Pulse H3/2 Red Wire:12V output (+) H3/3 Green Wire: (-) 200mA Lock Pulse, (+) 200mA Unlock Pulse 2 Pin Blue Plug For Valet Switch
H4 H5
2 Pin White Plug For LED Indicator
H1: MAIN 5 PIN WIRE HARNESS: 1. Red / White Wire: Parking Light Relay input 2. White Wire: Parking Light Relay Output 3. Black Wire: Ground to Vehicle FRAME 4. Brown Wire: Positive output To Siren Or Horn (Programmable)
15A Fuse
5. Red Wire: +12V To Constant Battery Source
H2: 6 PIN MINI CONNECTOR WIRE HARNESS: 12V 1. Violet Wire: Positive Door Pin Switch Input 2. Blue Wire: Instant Trigger Ground
3. Green Wire: Negative Door Pin Switch Input
12V
4. Yellow Wire: To Ignition Switched + 12V Cut
From ignition switch
5. Orange Wire: 200mA Grounded when armed Red wire
30
6. Gray Wire: (-) 200mA Programmable Output Channel 2 / 2 Step Door Unlock / Pager Output.
To start solenoid White wire Orange wire
85
87a 86 87
H6: 4 PIN WHITE CONNECTOR FOR 2 STAGE SHOCK SENSOR 1. Green Wire / Warn Away Input 2. Blue Wire / Ground Trigger 3. Black Wire / Negative 4. Red Wire / + 12Volts
DOOR LOCK DIAGRAMS 5-WIRE ALTERNATING DOOR LOCK +12V
Green Wire
Master Door Lock Switch Splice
86 3 Pin Plug To Alarm
87
87a
Cut the Existing Unlock Wire
30
85
X
Splice +12V
86
87
87a
Cut the Existing Lock Wire
X 30
To Door Lock Motor
85 Blue Wire
To Slave Door Lock switches
VACUUM OPERATED CENTRAL LOCKING Green Wire
86
87
87a
Door Switch 30
X Cut
85
3 Pin Plug To Alarm
+12V 86 87
Compressor 87a 30 85
Blue Wire
VACUUM OPERATED DOOR LOCKING SYSTEM: TYPICAL OF MERCEDES BENZ AND AUDI. Locate the wire under the driver's kick panel. Use the voltmeter connecting to ground, verify that you have the correct wire with the doors unlocked, the voltmeter will receive "12 volts". Lock the doors and the voltmeter will read "0 volt". Move the alligator clip to +12V and the voltmeter will receive "12 volts". Cut this wire and make connections. Be sure to program door lock timer to 3 seconds.(See Feature II – 1 Programming.)
2 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS 6-Pin Plug From Alarm
OEM Door Master Lock Switch H3/6 Gray Wire Unlock
Lock
Existing Neg. 3 Pin Plug To Alarm
H7/3 Green Wire Door Lock
Existing Neg. Lock Wire
Unlock Wire
H7/1 Blue Wire Door Unlock
87 85
86
OEM Door Lock Relay
87A 30
+ 12V OEM Door Lock Motor
X
To All Other Door Lock Motors
Cut Existing Unlock
2 STEP DOOR UNLOCK WIRE CONNECTION FOR POSITIVE SWITCHED DOOR LOCKS +12V 6-Pin Plug From Alarm
OEM Door Master Lock Switch
H3/6 Gray Wire
87
Unlock 86
87A
Existing Pos. Unlock Wire
30
H7/3 Green Wire Door Lock
Lock
85
+ 12V
Existing Pos. Lock Wire
87 87A
+ 12V 85
86 30
H7/1 Blue Wire Door Unlock
+ 12V OEM Door Lock Relay
87 87A 85
86 OEM Driver's Door Lock Motor
30
X
To All Other Door Lock Motors
Cut Existing Unlock
STARTER DISABLE RK-1 87
<12V (+) Ignition>
87a
85
STARTER
30
86
Orange Starter Disable Wire
PROGRAMMING PROGRAMMING TRANSMITTER:
Enter: 1.
Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds, rd 2. Push the Valet switch 3 times and hold in on the 3 push; when a long chirp is heard then release the valet switch. You are now in the Transmitter programming mode. Program: 1. Press any button on the first transmitter until the siren responds with a confirming chirp; the first transmitter is now programmed. 2. Press any button on the second transmitter until the siren responds with a confirming chirp; the second transmitter is now programmed. th 3. Apply the same procedure to program any 3rd and 4 transmitters. Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps will confirm exit. Note: If more than 4 transmitters programmed, the system will only keep the last 4 transmitters. ALARM FEATURE “I” PRORAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. nd 2. Push the Valet switch 2 times and hold in on the 2 push; when a long chirp is heard then release the valet switch. You are now in the Alarm feature ‘I’ programming mode. 3. Press the transmitter button corresponding to the feature you want to program. a. The factory default settings is always [1] LED flash, [1] chirp. 4. Depress the transmitter button again to change the feature. Simply keep pressing the transmitter button again until the module advances to your desired setting. Press Transmitter Button 1
One Chirp / LED one pulse Factory Default Setting Chirps on
Two Chirps / LED two pulse
Automatic Rearm On
Automatic Rearm Off
With Door Ajar error chirp
Bypass Door Ajar error chirp.
Chirps off
2 3
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
ALARM FEATURE “II” PRORAMMING: 1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. th 2 Push the Valet switch 4 times and hold in on the 4 push; when a long chirp is heard, then release the valet switch. You are now in the Alarm feature ‘II’ programming mode. 3 Press the transmitter button corresponding to the feature you want to program. Press One Chirp / Two Chirps / Three Chirps / Transmitter LED one pulse LED two pulse LED three pulse Button Factory Default Setting 0.9-second Door 3.0-second Door Double pulse 1 lock pulses. lock pulse. unlock Active arming Passive arming Passive arming 2 without passive with passive door door locking locking. Ignition controlled Without ignition 3 door locks & controlled door unlocks locks & unlocks Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
ALARM FEATURE “III” PRORAMMING: 1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. th 2 Push the Valet switch 6 times and hold in on the 6 push; when a long chirp is heard, then release the valet switch. You are now in the Alarm feature ‘III’ programming mode. 3 Press the transmitter button corresponding to the feature you want to program. Press Transmitter Button
1 2 3
One Chirp / LED one pulse Factory Default Setting
Two Chirps / LED two pulse
H1/4 Brown Wire = Siren Output H2/6 Gray Wire = Trunk (Channel 2) Output
H1/4 Brown Wire = Horn Output H2/6 Gray Wire = Two Step Door Unlock Output
Car Jacking Off
Car Jacking On
Three Chirps / LED three pulse
H2/6 Gray Wire = Pager Output
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit
Technical Support: 800-262-2527 ext. 461 (For Authorized Dealers Only)
NOTES
th
1815 West 205 Street, Suite 101 Torrance, California 90501-1525 Main Office: 310-618-2002
www.autopageusa.com
