Transcript
Card with HD Antenna Installation manual
Installers: Please first confer with the customer to determine the desired position for the Card in the car. We advise to place the Card Holder so that the Card will be easily visible for - and within comfortable reach of - the driver.
Recommended drilling locations
SCHEMATIC VIEW Module locations
J K G
C
E D F H
B
1. Card Holder There are several ways to mount the Card Holder: • Double-sided tape. The use of double-sided tape provides one of the easiest ways to attach the holder inside small compartments. Make sure all surfaces are free of grease and dirt. • Screws from the top. Unscrew the holder. Next drill little holes in the the top half and screw it into the selected position. Make sure to not use screws that might get in the way of the speaker or the Card when inserted into the Holder. Finish by screwing the bottom half of the Holder back into place using four small screws. • Screws from the bottom. Unscrew the holder. Carefully drill four matching holes in the selected location on the dash board that correspond exactly with the four screw hole openings of the Holder. Now use longer screws to simultaneously screw the top and bottom half of the Holder back together and into the dashboard.
B C
Many drivers prefer to have the Card Holder installed in a suitable compartment. Creative installers can also opt to custom make an opening in the dashboard or in the ceiling of the car.
A
A
In or behind the bumper/grill A HD Antenna B Laser Fiber (Front & Rear) B A Laser Receiver Square (F&R) Laser Transmitter Square (F&R) C Extention Box (F&R) D Laser Center E Splitter Cable F Power Plug Under the bonnet / In the boot G GPS Antenna H Speaker (optional) C J Card Holder K Card
2. Splitter Cable Place the Splitter Cable under the dashboard and connect the plug to the back of the Card Holder. The sound of a click is usually a good indication it has been connected correctly.
See reverse side for wiring diagram
4. HD Antenna Place the HD Antenna at the front of the car behind the bumber or spoiler. Preferably behind flat and smooth plastic, and certainly not behind metal. • The large, smooth side that has no imprints, must face straight forward in the driving direction, with the cable coming out on the left or right side, as depicted. • Connect the cable to port 1, 2, 3 or 4 of the Extension Box. • For maximum performance, please make sure the antenna receives sufficient airflow for cooling. • Please see reverse side of this sheet for MultaRadar CD optimized installation.
E
Car specific
G
H
F
ing Facward for
In the cockpit
J
K
6. Lasers Connect the Lasers to the Laser Center: Laser Receiver to a Receiver port, Laser Transmitter (square or fiber) to a Transmitter port. Attention: The Laser Transmitter has a ‘horizon’ icon embossed on the front lens indicating this side must go below. Laser Square - Recievers Laser Square - Transmitters
Standard position: Place antenna vertically (portrait orientation).
To ensure optimal laser functionality, please refer to the exact laser installation instructions in the provided Stinger Laser Installation Manual. Download available at: www.stinger.com/manuals
7. GPS Antenna Place the antenna on the dashboard. If the car has a heatrepelling windshield, it is better to place the antenna outside the cabin of the car, for instance in a space at the top end of the bonnet. • Connect the cable of the antenna to the GPS port of the Card Holder.
3. Extension Box Place the Extension Box horizontally (as depicted) under the bonnet, in a reasonably humidity-free location. • Connect the Extension Box to the Card Splitter Cable with the supplied cable.
Under the dashboard
D
5. Laser Center Place the Laser Center under the dashboard. • First make sure the Splitter Cable is attached to the Card Holder. Then connect one end of the Bridge Cable to either of the ports on the Splitter Cable, and the other end of the Splitter Cable to the C1-port on the Laser Center.
8. Power Plug • Connect the red wire directly to the (continuous) 13.8V battery power (+30). • Connect the orange wire to the ignition-actuated 13.8V battery power (+15). • Connect the black wire to a ‘clean’ metal ground-point of the car chassis. • When connecting the plug to the Card Holder, the sound of a click is usually a good indication it has been connected correctly.
Rubber seal Cable Cut outs Rubber seal
9. Closing the Extension Box After all the cables have been connected, it is important to close the boxe (see steps 3) in a water resistant manner. Place the cables in the holes of the opposite facing ‘rubber seals’ (see example). This prevents moisture from getting into the box. Next, place the rubber seals with the now inserted cables into the slot, as depicted in the example on the left. Make sure the rubbers are pushed down all the way using silicone spray to facilitate this. Put the lid back on so that it is tight and secure.
Stinger Card HD - Installation manual INT-V3.0 - © Stinger 2017 - Changes reserved
STEP BY STEP INSTRUCTIONS
For optimal performance of the Stinger Card it is important to carefully follow the directions provided in this installation manual. For questions please call Stinger technical support at +31 252 41 49 50. For more information, check www.stinger.com
WIRING DIAGRAM
INSTALLATION HD ANTENNA
HD Antenna installation The HD Antenna can best be instsalled vertically in most regions. Those drivers who wish to have optimized reception of MultaRadar CD signals can choose to have the antenna mounted diagonally, as explained in the overview below.
90o
FRONT
EXT
R1
R2
R3
T1
T2
R4
R5
R6
T5
T6
RECEIVERS
90o
T3
T4
T7
Side 1
REAR
Side 2
GPS
TRANSMITTERS
C1
C2
USB
Speaker Power
Aim antenna straight forward
Standard installation See front side of this installation manual (under 3.) for instructions.
Multaradar CD optimized installation 1. Diagonally place the antenna behind the bumper or spoiler, with the smooth surface facing forward.
HD ANTENNA
EXTENSION BOX #1 Port 1 Port 2 Port 3 Port 4
CARD HOLDER
45°
SPLITTER CABLE
2
2. From the point of view of the driver, the cable connection must be on the bottom right of the antenna. Take note: If, from the point of view of the driver, the cable connection is on the top right or bottom left, the reception will be strongly reduced.
1,5A slow
Antenna must face outward and parallel to the road
SIDE
SPEAKER EXTERNAL OPTIONAL
SWITCHED
GPS
(IGNITION ON)
CONTINUOUS POWER SUPPLY 13.8 V (+30)
POWER SUPPLY 13.8 V (+15)
TO THE
USB STICK
