Transcript
N/C
2
1
© 1998-2014 WIFI ANTENNAS
4
DISPLAY PORT DVI / VGA Touch Screen
EXTRA USB
HDMI TV OUT SECONDARY DISPLAY
USB ROW 1
LCD TOUCH
3 LCD TOUCH eSATA
EXTRA USB USB 3.0
LAN
6 5
USB ROW 2
FM IN
AUDIO IN 1
N/C
OUTPUT
AUDIO IN 2
TosLink
MIC IN
RGB UNIT SWITCHER
PRIMARY DISPLAY
VIDEO OUTPUTS
N/C
USB ROW 3
SILVER JACKS
www.drivesoft.net
9 N/C
AUDIO OUT 2
AUDIO PORTS
Audio Outputs
Video Connectors
When installing a switcher that has audio inputs, connect the Front Output (green) 3.5 jack of the CarPC to the Front Input 3.5 jack of the switcher. This connection allows you to split the audio signal into 6 RCA outputs. The connection also allows you to use the audio over-ride feature which passes the audio signal from the stock OEM radio to the coach amplifiers in case of a system malfunction. Zone 2 Audio Output (silver) More info upon request.
VGA/DVI connects to the VGA Splitter. The VGA Splitter connects to the Video Input on Touch Screens. The VGA Splitter is only needed when more than one touch screen is installed. (Refer to VGA Splitter Diagram).
HDMI Port connects to the TV (usually in partition wall). Display Port (optional) By using a Display Port-to-VGA adapter cable, the Display port can be converted to a VGA Video Output. You can connect this output to a Video Splitter, allowing multiple secondary VGA monitors to be connected. (Refer to TV Installation Guide).
eSATA - to connect eSATA hard drives and Blu-Ray Players. More info upon request.
8 7
AUDIO PORTS
USB Connectors
USB 1 is an extra port to connect to Additional USB Equipment. USB 2 is an extra port to connect to Additional USB Equipment. USB 3 connects to the front Driver’s Touch Screen cable. USB 4 connects to the rear Passenger’s Touch Screen cable. USB 5 connects to the Limousine Switcher Control Unit. USB 6 connects to the RGB LED Lighting Control Unit. USB 7 connects to the DVD/CD Player. USB 8 is an extra port to connect to Additional USB Equipment. USB 9 is an extra port to connect to Additional USB Equipment.
H67 .V4
Front Output (green) connects to the front channel inputs of the amp. Note: Rear Output (orange) & Subwoofer (black) are not supported on Windows 7 CarPC Systems. 5.1 Output info is available upon request.
Audio Inputs
EXTRA USB EXTRA USB DVD
HD RADIO RESET
USB ROW 4
N/C
RESET
GND IN
+ BATT IN
+5 OUT
+12 OUT
+ AMP OUT
+ IGN IN
POWER CONNECTOR
Power Connections
Constant Input Power (yellow) (+12V BATT) (12 awg) (15a fuse) connects directly to the coach auxiliary secondary battery. Ignition Input Power (red) (+12V IGN) (18 awg) (3a fuse) connects to the ignition output of the override panel labeled “Ign-Out”. Note: When an override panel is not installed, connect this wire directly to the ignition switch. Refer to Override Panel Diagram for more information. A relay between the car and pc ignition input is recommended. RTO (Remote Turn-On)(blue/white stirpe) (+12 RTO) (18 awg) remote output power to turn on the audio amplifier.
Audio Line Input (blue) connects to audio output of the HD-FM Radio. Audio Line/MIC Input (pink) is an extra audio device or MIC input. Audio Line Input (silver 1) connects to the rear auxiliary audio jack. Audio Line Input (silver 2) is an extra audio device input.
Ground (black) (-12V GND) connects to vehicle chassis ground.
HD-Radio Data/Power Port connects to the HD/FM radio tuner
5V Power Output (white/red stripe) (+5V output) (14 awg) connects to DVD player. Note: wire cannot exceed 25ft.
Communication
Soft Reset Input (green) (-12V reset) (18 awg) Connects to the Reset terminal of the override panel labeled “RST”. Note: When an override panel is not installed, connect this wire to a momentary switch with a ground input.
using the gray 8-pin din cable. (Note: HD-FM radio tuner should be mounted more than 2ft from the CAR-PC.)
WI-FI Antennas must be installed to acquire a Wi-Fi connection. LAN direct connection to shop router.
DTO (Device Turn-On) (white/blue stripe) (+12V DTO) device output power to turn on Drivesoft Limo Switching Devices.
DRIVESOFT CARPC DIAGRAM
DVAS-H67 V4
