Case Component Remove Mounting Bracket Remove Front Panel

Transcript

C50.K1000.00 Case component Multi-media port 5.25” mounting bracket Power LED HDD LED 3.5” mounting bracket Front door with lock Power switch button Pre-drilled holes for water-cooling system tube ODD module 12cm fan Reset switch button HDD module Ventilator for PCI slot 12cm fans with filter Door key is attach on the accessory box Remove mounting bracket Remove front panel Removable fan filter (12) (3) (1) 2 (6) (22) (31) 1 (1) (6) (1) Push 1. Remove four thumb screws. Loosing four screws to remove the front panel. 2. Slide the side panel backward . (22) 1. Remove the side panels. 2. Loosing four screws to remove the top cover. 3. Lift up the side panel. Motherboard 1. Loosing two thumb screws to remove the motherboard tray 2. Slide the motherboard tray gently towards the front panel 3. Lift up the motherboard tray to remove According to M/B specification, select proper screws points, engage the standoffs into the corresponding points of the M/B tray, secure the M/B with screws the standoffs. C50.K1000.00 ODD installation Disassemble the ODD ODD Note: Adding extra M3 screws to secure the ODD for traveling. ODD ODD 2. Place the HDD into the HDD cage with the anti-vibration rings. 1. Fasten the HDD screws with anti-vibration rubber rings to the HDD. Cable management HDD cage can be turned 180 degree. 1. Loosing all screws on the bottom panel, then turn the HDD cage 180 degree. 2. Secure all screws to fix the HDD cage. Note: M/B tray with cable management clips Using the tool to poke the water holes 9 7 Black(GND) 5 Green 3 White 1 Red KEY10 Black(GND) 8 Green 6 White 4 Red 2 9 7 Black(GND) 5 Green 3 White 1 Red HD AUDIO 2. Fasten four thumbscrews to secure. Please be careful while handing to avoid an incised wound. Black(AGND) NC Yellow(R-RET) KEY Blue(L-RET) 1 3 5 7 9 2 Red(MIC) 4 Brown(MIC-PWE) 6 Yellow(R-OUT) 8 10 Blue(L-OUT) EAR MIC USB KEY 10 Black(GND) 8 Green 6 White 4 Red 2 1. Push in gently. USB USB 9 Green(SENSE2 RETUR) 7 KEY 5 Orange(SENSE1 RETUR) 3 Black(PRESENCE) 1 Black(GND) Adding another screws on both sides of HDD brackets Note: to prevent the HDD loosing by an accidental bump. Pre-drilled holes for water-cooling system tube AC'97 Blue(PORT2 L) 10 Black(SENSE SEND) 8 Yellow(PORT2 R) 6 Brown(PORT1 R) 4 Red(PORT1 L) 2 anti-vibration rings fix into the slot. Pull and hold the plastic handle first, and push the ODD towards the front panel. USB SATA Cable 9 7 5 3 1 Black(GND) White(+12V) Red(TPB-) Black(VG) Orange(TPA-) 1394 IEEE1394 Black(KEY) 10 White(+12V) 8 Green(TPB+) 6 Black(VG) 4 Blue(TPA+) 2 E-SATA Connector C50.K1000.00 Changeable Front Door swing direction design Take the spindles off the top and bottom plate Loose the screws on the top panel plate as show in the image above. A B Remove the door, and place the door on a table top. Loose the nut to uninstall the lock ▼ Face to the top of the front panel. When lock at A side ▼ Face to the top of the front panel. Swap the hinge and door stop as show as the image above When lock at B side Reverse the step 2 and step 1 to secure the door panel. 1. Secure all screws, and lock 2. Check the lock working mechanism swing the right direction