Transcript
thank you for selecting a ducduc product Please check contents against the components list in these instructions. Also, please ensure there was no damage that may have occurred in shipping. If any components are missing or you find � any damage, please contact ducduc before continuing. Read all the instructions before use of the CRIB.
alex CRIB
Please remember to securely tighten all bolts and fasteners, and periodically check to make sure every component is properly and securely in place and all bolts and fasteners are tight. Pay close attention to the safety warnings in these instructions and on CRIB labels. A minimum of two people is required to safely assemble and move the CRIB. Do not attempt to move this CRIB alone - dragging or sliding it across a f�loor may cause structural damage.
CAUTION: Any mattress used in this CRIB must be at least 27 1/4 inches by 51 5/8 inches with a thickness not exceeding 6 inches. KEEP INSTRUCTIONS FOR FUTURE USE 8/10/2011
components
pictures are not drawn to scale
A
END PANEL X2
D
MATTRESS SUPPORT BOLT X4
B
SIDE RAIL X2
C
F
MATTRESS SUPPORT PANEL
RAIL CONNECTOR BOLT X8
F E
G
H
MATTRESS SUPPORT PIN X4
I I.1
LOCKING WASHER - LARGE (5/16”) X4
J.1
REGULAR WASHER - LARGE (5/16”) X4
I.2
LOCKING WASHER - SMALL (4/16”) X8
J.2
REGULAR WASHER - SMALL (4/16”) X8
ALLEN WRENCH (4mm)
SCREWDRIVER (not included)
assembly
1
Lay END PANEL
A
on floor � with rail-connector-holes facing up.
rail-connector-holes
rail-connector-holes A
2
Align SIDE RAIL B to END PANEL A so that the rail-connector-holes on SIDE RAIL B line up with the rail-connector-holes on END PANEL Make sure the four mattress-support-holes face the bottom and inside of END PANEL A . Refer to picture for correct orientation. Label on bottom of END PANEL A and SIDE RAIL B that reads “Bottom” should be facing the bottom of the CRIB.
A
.
rail-connector-holes
B
mattress-support-holes A
3
Attach one LOCKING WASHER
I.2
to each RAIL CONNECTOR BOLT RAIL CONNECTOR BOLTS with ALLEN WRENCH
F
G
and one REGULAR WASHER F
J.2
and insert two
in rail-connector-holes and tighten G
G F I.2
J.2
I.2
G J.2
4
Align second SIDE RAIL
B
to END PANEL
A
making sure that
mattress-support-holes face the bottom and inside of CRIB. Refer to diagram for proper orientation. Attach one LOCKING WASHER
I.2
to each RAIL CONNECTOR BOLT RAIL CONNECTOR BOLTS with ALLEN WRENCH
F
and one REGULAR WASHER F
J.2
and insert two
in rail-connector-holes and tighten
G
I.2
F
J.2 B
I.2 J.2
G
G A
5
Carefully stand crib upright. This requires two people. One person holds onto crib to prevent it from tipping over during assembly step 6.
2 1 3
6
Line up other END PANEL
so its rail-connector-holes
A
align with the rail-connector-holes on the SIDE RAILS Attach LOCKING WASHERS
I.2
to RAIL CONNECTOR BOLTS
F
ALLEN WRENCH
.
and REGULAR WASHERS
J.2
and insert and tighten
the four RAIL CONNECTOR BOLTS G
B
F
with
as in steps 3 and 4.
J
J.2
F
I I.2
A
F
7
The MATTRESS SUPPORT PANEL
C
may be installed in one of four positions.
See the four different mattress-support-holes in each corner of the CRIB. First, select the desired mattress height. Then, unscrew the MATTRESS SUPPORT PIN
E
from each MATTRESS SUPPORT BOLT D. . Insert the smooth ends
of each MATTRESS SUPPORT PIN SIDE RAILS
B
E
in the desired mattress-support-holes on
. See drawing for proper pin orientation.
E
8
Carefully lower MATTRESS SUPPORT PANEL
C
with labels facing up.
Align corner-holes to sit on MATTRESS SUPPORT PINS
E
.
C
corner-holes
9
Attach one REGULAR WASHER J.1 and one LOCKING WASHER on top of each MATTRESS SUPPORT PIN E .
I.1
Secure and tighten each of the four MATTRESS SUPPORT BOLTS to each of the four MATTRESS SUPPORT PINS Use SCREWDRIVER
H
E
D
.
to tighten securely. H
D
I.1 J.1
E
10
Press firmly in center of MATTRESS SUPPORT PANEL
C
to ensure proper placement. In the event MATTRESS SUPPORT PANEL
C
does not appear to be secure, remove
and repeat steps 7 to 9. The MATTRESS SUPPORT PANEL
C
must be� firmly attached at all four corners.
C
operation The mattress height should be lowered as your baby grows to ensure that he/she does not climb out of the CRIB. When child is able to pull to standing position, set mattress to lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out. Regularly assess your baby’s abilities and make adjustments accordingly. To adjust the height of the mattress support, remove the mattress from the crib. Unscrew all four MATTRESS SUPPORT BOLTS D , r e mo ve a ll L OCK IN G W ASHE R S I.1 an d R EGULAR WASHER S J.1, and remove MATTRESS SUPPORT PANEL C . Remove and reinsert the smooth ends of each MATTRESS SUPPORT PIN E in mattress-support-holes on SIDE RAILS B at desired height. Refer to steps 8 through 10 for reinserting MATTRESS SUPPORT PANEL C and reattaching, REGULAR WASHERS J.1 LOCKING WASHERS I.1 , and MATTRESS SUPPORT BOLTS D . Periodically check to make �sure every component is properly and securely in place and all bolts and fasteners are tight. Do not scratch or chip the finish. � Do not use abrasive chemicals for cleaning. Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you ever re�finish this furniture, be sure to use only a non-toxic finish � specif�ed for children’s furniture. Store crib in a dry area.
decal application for optional decal
Please follow these directions to apply optional vinyl decal. Make sure that the crib surface is clean and dry. Vinyl is easier to apply before the crib is assembled.
Use invisible tape to attach decal at the desired location. Apply tape only on the top edge of the decal.
Gently lift the decal up without removing it from the crib and
slowly peel off the back layer of paper. The adhesive on the back of the decal is very sticky. Make sure that the back of the decal does not touch the crib surface while you are removing the back layer of paper.
Once the back layer of paper is removed, lower the decal to make contact with the crib surface.
Apply pressure on top of the decal to adhere decal to crib surface. Start from the middle and work your way out to the sides. Use a hard and smooth object such as a credit card to rub on top of the decal. Make sure to apply pressure on all areas of the graphic.
Starting at one corner, slowly remove the top layer of paper and invisible tape.
Failure to follow these warnings and the assembly instructions could result in serious injury or death. Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE. Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under infant. To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician. Strangulation Hazard:
Strings can cause strangulation! Do not place items with a string around a child’s neck, such as hood strings or pacifierer cords. Do not suspend strings over a crib or attach strings to toys. To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners. DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out. Stop using crib when child begins to climb out or reaches the height of 35 in. (89 cm.). Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or broken. Contact ducduc for replacement parts and instructional literature if needed. DO NOT substitute parts. If refinishing, use a non-toxic finish specified for children’s products. Follow warnings on all products in a crib. Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation. Infants can suffocate in gaps between crib sides and a mattress that is too small.
ducduc llc 524 broadway no. 206 ny ny 10012 t 212.226.1868 f 212.226.5504
www.ducducnyc.com
