Transcript
CDX-F7000/F7005X/FW700 SERVICE MANUAL
US Model CDX-F7000/F7005X/FW700
Ver 1.0 2003. 12
Canadian Model CDX-F7000/F7005X
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
CDX-S2000/SW200
AUDIO POWER SPECIFICATIONS (US Model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion.
CD Drive Mechanism Type
MG-611XA-186//K
Optical Pick-up Name
KSS1000E
SPECIFICATIONS General
CD player section Signal-to-noise ratio Frequency response Wow and flutter
120 dB 10 – 20,000 Hz Below measurable limit
Inputs
Tuner section FM Tuning range Antenna terminal Intermediate frequency Usable sensitivity Selectivity Signal-to-noise ratio
87.5 – 107.9 MHz External antenna connector 10.7 MHz/450 kHz 9 dBf 75 dB at 400 kHz 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz AM Tuning range Antenna terminal Intermediate frequency Sensitivity
Outputs
530 – 1,710 kHz External antenna connector 10.7 MHz/450 kHz 30 µV
Power amplifier section Outputs
Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms)
Tone controls Loudness Power requirements Dimensions Mounting dimensions Mass Supplied accessories
Audio output terminals (front/rear) Subwoofer output terminal (mono) Power antenna relay control terminal Power amplifier control terminal Telephone ATT control terminal Illumination control terminal BUS control input terminal BUS audio input or AUX IN terminal Remote controller input terminal Antenna input terminal Bass ±10 dB at 62 Hz Treble ±10 dB at 16 kHz +8 dB at 100 Hz +2 dB at 10 kHz 12 V DC car battery (negative ground) Approx. 178 × 50 × 178 mm (7 1/8 × 2 × 7 1/8 in.) (w/h/d) Approx. 182 × 53 × 161 mm (7 1/4 × 2 1/8 × 6 3/8 in.) (w/h/d) Approx. 1.3 kg (2 lb. 14 oz.) Parts for installation and connections (1 set) Front panel case (1) Card remote commander RM-X118A
Design and specifications are subject to change without notice.
FM/AM COMPACT DISC PLAYER 9-961-473-01
Sony Corporation
2003L04-1 © 2003. 12
e Vehicle Company Published by Sony Engineering Corporation
1
CDX-F7000/F7005X/FW700
SERVICE NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block. optical pick-up
NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat.
semi-fixed resistor
TEST DISCS This set can playback CD-R and CD-ROM discs. The following test discs should be used to check the capability: CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) CD-RW test disc TCD-W082L (Part No. J-2502-063-2) Notes on CD-R/CD-RW discs • You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs) designed for audio use on this unit. Look for these marks to distinguish CD-Rs/CD-RWs for audio use.
These marks denote that a disc is not for audio use. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
• Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. • You cannot play a CD-R/a CD-RW that is not finalized*. * A process necessary for a recorded CD-R/CD-RW disc to be played on the audio CD player.
CDX-F7000/F7005X/FW700
z
UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CNP301) and the SERVO board (CN1) with the extension cable (Part No. J-2502-076-1).
MAIN BOARD CNP301
J-2502-076-1
SERVO BOARD CN1
3
CDX-F7000/F7005X/FW700
TABLE OF CONTENTS 1. GENERAL Location of Controls ................................................................ 5 Connections (CDX-F7000/F7005X) ....................................... 6 Connections (CDX-FW700) .................................................... 7
2. DISASSEMBLY 2-1. Sub Panel Assy (CD) ........................................................... 9 2-2. CD Mechanism Block ......................................................... 9 2-3. Main Board ....................................................................... 10 2-4. Chassis (T) Sub Assy ........................................................ 10 2-5. Roller Arm Assy ................................................................ 11 2-6. Chassis (OP) Assy ............................................................. 11 2-7. Optical Pick-up ................................................................. 12 2-8. SL Motor Assy (M902) ..................................................... 12 2-9. LE Motor Assy (M903) ..................................................... 13 2-10. Servo Board ....................................................................... 13
3. DIAGRAMS 3-1. 3-2. 3-3. 3-4. 3-5.
IC Pin Descriptions ........................................................... 14 Block Diagram –CD Section– ........................................... 19 Block Diagram –Main Section– ........................................ 20 Block Diagram –Display Section– .................................... 21 Note for Printed Wiring Boards and Schematic Diagrams .......................................................... 22 3-6. Waveforms ......................................................................... 22 3-7. Circuit Boards Location .................................................... 22 3-8. Printed Wiring Boards –CD Mechanism Section– ............ 23 3-9. Schematic Diagram –CD Mechanism Section– ................ 24 3-10. Schematic Diagram –Main Section (1/3)– ........................ 25 3-11. Schematic Diagram –Main Section (2/3)– ........................ 26 3-12. Schematic Diagram –Main Section (3/3)– ........................ 27 3-13. Printed Wiring Boards –Main Section– ............................ 28 3-14. Printed Wiring Board –Sub Section– ................................ 30 3-15. Schematic Diagram –Sub Section– ................................... 31 3-16. Printed Wiring Board –Key Section– ................................ 32 3-17. Schematic Diagram –Key Section– ................................... 33 3-18. IC Block Diagrams ............................................................ 34
4. EXPLODED VIEWS 4-1. 4-2. 4-3. 4-4. 4-5. 4-6.
Main Section ..................................................................... 36 Front Panel Section ........................................................... 37 CD Mechanism Section (1) ............................................... 38 CD Mechanism Section (2) ............................................... 39 CD Mechanism Section (3) ............................................... 40 CD Mechanism Section (4) ............................................... 41
5. ELECTRICAL PARTS LIST ......................................... 42
4
CDX-F7000/F7005X/FW700 SECTION 1 GENERAL
Location of controls Card remote commander RM-X118A Refer to the pages listed for details. a DSPL (display mode change) button 12, 14, 21 b Number buttons Radio: To store stations/receive stored stations. CD/MD: (1): REP 13 (2): SHUF 13 c DSO button 23 d MENU button To display the menus. e SOURCE (Power on/Radio/CD/MD*1/ AUX*2) button To select the source. f SEEK/AMS () buttons b Volume control dial/SOUND button Rotate to: – Adjust the volume. – Adjust the sound settings. Press to: – Select the sound items. 3 qs DISC (ALBUM)/PRESET (+/–) buttons 4 MODE button 6 DSO button 7 SCRL (scroll) button 8 Display window 9 Z (eject) button (located on the front side of the unit, behind the front panel) 10, 11 0 OPEN button 9, 10, 11 qa Receptor for the card remote commander
REP
The buttons on the unit share the same functions as those on the card remote commander. a 5 SEEK/AMS (.m/M>) buttons b Volume control dial/SOUND button Rotate to: – Adjust the volume. – Adjust the sound settings. Press to: – Select the sound items. 3 qs DISC (ALBUM)/PRESET (+/–) buttons 4 MODE button 6 DSO button 7 SCRL (scroll) button 8 Display window 9 Z (eject) button (located on the front side of the unit, behind the front panel) 10, 11 0 OPEN button 9, 10, 11 qa Receptor for the card remote commander
qd OFF (Stop/Power off) button* qf EQ7 button qg RESET button (located on the front side of the unit, behind the front panel) 8 qh SOURCE button qj Number buttons qk DSPL (display mode change) button ql IMAGE button 23 * Warning when installing in a car without an ACC (accessory) position on the ignition switch After turning off the ignition, be sure to press and hold (OFF) on the unit until the display disappears. Otherwise, the display does not turn off and this causes battery drain.
qd OFF (Stop/Power off) button* qf EQ7 button qg RESET button (located on the front side of the unit, behind the front panel) 8 qh SOURCE button qj Number buttons qk DSPL (display mode change) button ql IMAGE button 23 * Warning when installing in a car without an ACC (accessory) position on the ignition switch After turning off the ignition, be sure to press and hold (OFF) on the unit until the display disappears. Otherwise, the display does not turn off and this causes battery drain.
6
5
CDX-F7000/F7005X/FW700
Connections (CDX-F7000/F7005X)
3
*1 *4
Source selector (not supplied) Sélecteur de source (non fourni)
*3
Supplied with the CD/MD changer Fourni avec le changeur de CD/MD
XA-C30
*5 BUS AUDIO IN /AUX IN*2
AUDIO OUT FRONT
REMOTE IN *1 RCA pin cord (not supplied) *2 Be sure to match the color-coded cord for audio to the appropriate jacks from the unit. If you connect an optional CD/MD unit, you cannot use AUX IN terminal. *3 Auxiliary optional equipment such as portable DVD player (not supplied) *4 Supplied with the auxiliary equipment *5 Supplied with XA-C30 *6 Insert with the cord upwards.
L
*
1
R
SUB OUT (MONO)
*6
from car antenna à partir de l’antenne de la voiture
3
Blue/white striped Rayé bleu/blanc
AMP REM
BUS CONTROL IN
AUDIO OUT REAR Fuse (10 A) Fusible (10 A)
Max. supply current 0.3 A Courant max. fourni 0,3 A
4 Black Noir
1
White Blanc Blue Bleu
Left Gauche
ANT REM
White/black striped Rayé blanc/noir Gray Gris
2
Max. supply current 0.1 A Courant max. fourni 0,1 A Light blue Bleu ciel
ATT
Right Droit Gray/black striped Rayé gris/noir Green Vert Left Gauche Green/black striped Rayé vert/noir Purple Mauve Right Droit
Orange/white striped Rayé orange/blanc
ILLUMINATION
Red Rouge
4
*1 Cordon à broche RCA (non fourni) *2 Veillez à faire correspondre le code couleur audio aux fiches de l’appareil. Si vous raccordez un appareil CD ou MD en option, vous ne pouvez pas utiliser la borne AUX IN. *3 Appareil auxiliaire en option, par exemple un lecteur de DVD portable (non fourni) *4 Fourni avec l’appareil auxiliaire *5 Fourni avec le XA-C30 *6 Insérez avec le câble vers le bas.
5 6
Yellow Jaune
7
Purple/black striped Rayé mauve/noir
Connection diagram (3) 1 To a metal surface of the car First connect the black ground lead, then connect the yellow and red power input leads. 2 To the power antenna control lead or power supply lead of antenna booster amplifier
3
4 5
6
Notes • It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna. • When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.” To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. To the interface cable of a car telephone To a car’s illumination signal Be sure to connect the black ground lead to a metal surface of the car first. To the +12 V power terminal which is energized in the accessory position of the ignition key switch
Notes • If there is no accessoryposition, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal surface of the car first. • When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.” 7 To the +12 V power terminal which is energized at all times Be sure to connect the black ground lead to a metal surface of the car first.
Schéma de raccordement (3) Notes on the control and power supply leads • The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna in the rear/side glass, connect the power antenna control lead (blue) or the accessorypower input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer. • A power antenna without a relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis,or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly.
1 À un point métallique de la voiture Branchez d‘abord le fil de masse noir et, ensuite, les fils d‘entrée d‘alimentation jaune et rouge. 2 Vers le fil de commande de l‘antenne électrique ou le fil d‘alimentation de l‘amplificateur d‘antenne
3
4 5
6
Remarques • Il n'est pas nécessaire de raccorder ce fil s'il n'y a pas d'antenne électrique ni d'amplificateur d'antenne, ou avec une antenne télescopique manuelle. • Si votre voiture est équipée d'une antenne FM/ AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les fils de commande et d'alimentation ». Au niveau du AMP REMOTE IN de l’amplificateur de puissance en option Ce raccordement s’applique uniquement aux amplificateurs. Le branchement de tout autre système risque d’endommager l’appareil. Vers le cordon de liaison d’un téléphone de voiture Vers le connecteur du signal d’éclairage de la voiture Raccordez d’abord le fil de masse noir à un point métallique du véhicule. À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoires
Remarques • S'il n'y a pas de position accessoires,raccordez la borne d'alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le fil de masse noir à un point métallique du véhicule. • Si votre voiture est équipée d'une antenne FM/ AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les fils de commande et d'alimentation ». 7 À la borne +12 V qui est alimentée en permanence Raccordez d’abord le fil de masse noir à un point métallique du véhicule.
Remarques sur les fils de commande et d’alimentation • Le fil de commande de l’antenne électrique (bleu) fournit une alimentation de + 12 V CC lorsque vous mettez la radio sous tension. • Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le fil de commande de l’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre détaillant. • Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le fil d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt. Remarques sur le raccordement des haut-parleurs • Avant de raccorder les haut-parleurs, mettez l’appareil hors tension. • Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité électrique adéquate pour éviter de les endommager. • Ne raccordez pas les bornes du système de hautparleurs au châssisde la voiture et ne raccordez pas les bornes des haut-parleurs droit à celles du haut-parleur gauche. • Ne raccordez pas le câble de masse de cet appareil à la borne négative (–) de l’enceinte. • N’essayez pas de raccorder les haut-parleurs en parallèle. • Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des hautparleurs peut endommager l’appareil. • Pour éviter tout dysfonctionnement, n’utilisez pas les fils des haut-parleurs intégrés installés dans votre voiture si l’appareil partage un fil négatif commun (–) pour les haut-parleurs droit et gauche. • Ne raccordez pas entre eux les cordons des hautparleurs de l’appareil. Remarque sur le raccordement Si les haut-parleurs et l’amplificateur ne sont pas raccordés correctement, le message « FAILURE» s’affiche. Dans ce cas, assurez-vous que les hautparleurs et l’amplificateur sont bien raccordés.
6
CDX-F7000/F7005X/FW700
Connections (CDX-FW700)
3
*1 *4 *
Source selector (not supplied) Selector de fuente (no suministrado)
3
Supplied with the CD/MD changer Suministrado con el cambiador de CD/MD
XA-C30
*5 BUS AUDIO IN /AUX IN*2
AUDIO OUT FRONT
REMOTE IN *1 RCA pin cord (not supplied) *2 Be sure to match the color-coded cord for audio to the appropriate jacks from the unit. If you connect an optional CD/MD unit, you cannot use AUX IN terminal. *3 Auxiliary optional equipment such as portable DVD player (not supplied) *4 Supplied with the auxiliary equipment *5 Supplied with XA-C30 *6 Insert with the cord upwards.
L
*
1
R
SUB OUT (MONO)
*6
from car antenna desde la antena del automóvil
Fuse (10 A) Fusible (10 A)
3
AMP REM
BUS CONTROL IN
AUDIO OUT REAR Blue/white striped Con rayas azules y blancas
Max. supply current 0.3 A Corriente máx. de alimentación de 0,3 A
4 Black Negro
1
White Blanco Blue Azul
Left Izquierdo
ANT REM
White/black striped Con rayas blancas y negras Gray Gris
2
Max. supply current 0.1 A Corriente máx. de alimentación de 0,1 A Light blue Azul celeste
ATT
Right Derecho Gray/black striped Con rayas grises y negras Green Verde Left Izquierdo Green/black striped Con rayas verdes y negras Purple Morado Right Derecho
Orange/white striped Con rayas naranjas y blancas
ILLUMINATION
Red Rojo
4 5
*1 Cable con terminales RCA (no suministrado) *2 Asegúrese de hacer coincidir el código codificado con colores para audio con las tomas apropiadas de la unidad. Si conecta una unidad de CD/MD opcional, no podrá utilizar el terminal AUX IN. *3 Equipo opcional auxiliar como un reproductor de DVD portátil (no suministrado) *4 Suministrado con el equipo auxiliar *5 Suministrado con el XA-C30 *6 Insertar con el cable hacia arriba.
6
Yellow Amarillo
7
Purple/black striped Con rayas violetas y negras
Connection diagram (3) 1 To a metal surface of the car First connect the black ground lead, then connect the yellow and red power input leads. 2 To the power antenna control lead or power supply lead of antenna booster amplifier
3
4 5
6
Notes • It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna. • When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.” To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. To the interface cable of a car telephone To a car’s illumination signal Be sure to connect the black ground lead to a metal surface of the car first. To the +12 V power terminal which is energized in the accessory position of the ignition key switch
Notes • If there is no accessoryposition, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal surface of the car first. • When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.” 7 To the +12 V power terminal which is energized at all times Be sure to connect the black ground lead to a metal surface of the car first.
Diagrama de conexión (3) Notes on the control and power supply leads • The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna in the rear/side glass, connect the power antenna control lead (blue) or the accessorypower input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer. • A power antenna without a relay box cannot be used with this unit.
1 A una superficie metálica del automóvil Conecte primero el cable de toma a tierra negro, y después los cables con raya naranja/blanca, amarillo, y rojo de entrada de alimentación. 2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de antena
Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis,or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “Failure” appears in the display. In this case, make sure the speaker and amplifier are connected correctly.
3
4 5
6
Notas • Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. Para conectar a AMP REMOTE IN del amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad. Al cable de interfaz de un teléfono para automóvil A una señal de iluminación del automóvil Asegúrese de conectar primero el cable de toma a tierra negro a una superficie metálica del automóvil. Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de la llave de encendido
Notas • Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de toma a tierra negro a una superficie metálica del automóvil. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero/lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”. 7 Al terminal de alimentación de +12 V que recibe energía sin interrupción Asegúrese de conectar primero el cable de toma a tierra negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación • El cable de control de la antena motorizada (azul) suministrará cc de + 12V cuando conecte la alimentación del sintonizador. • Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de entrada de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener más información, consulte a su proveedor. • Con esta unidad no es posible utilizar una antena motorizada sin caja de relé.
Conexión para protección de la memoria Si conecta el conductor de entrada amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague la llave de encendido. Notas sobre la conexión de los altavoces • Antes de conectar los altavoces, desconecte la alimentación de la unidad. • Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de potencia adecuada para evitar que se dañen. • No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. • No conecte el cable de toma a tierra de esta unidad al terminal negativo (–) del altavoz. • No intente conectar los altavoces en paralelo. • Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. • Para evitar fallos de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si su unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo. • No conecte los cables de altavoz de la unidad entre sí. Nota sobre la conexión Si el altavoz y el amplificador no están conectados correctamente, aparecerá “Failure” en la pantalla. Si es así, compruebe la conexión de ambos dispositivos.
7
CDX-F7000/F7005X/FW700 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence.
SET 2-1.
SUB PANEL ASSY (CD) (Page 9)
2-2.
CD MECHANISM BLOCK (Page 9)
2-3.
MAIN BOARD (Page 10)
2-7.
8
2-4.
CHASSIS (T) SUB ASSY (Page 10)
2-5.
ROLLER ARM ASSY (Page 11)
2-10. SERVO BOARD (Page 13)
2-6.
CHASSIS (OP) ASSY (Page 11)
2-8.
SL MOTOR ASSY (M902) (Page 12)
OPTICAL PICK-UP (Page 12)
2-9.
LE MOTOR ASSY (M903) (Page 13)
CDX-F7000/F7005X/FW700
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL ASSY (CD)
3 two claws
4 2 two claws
CN601 1 two screws (+PTT 2.6 x 6) 5 sub panel assy (CD)
2-2. CD MECHANISM BLOCK
7 bracket (CD) 5 CD mechanism block 6 two screws (+PTT 2.6 x 6)
2 screw (+PTT 2.6 x 6)
3
1 screw (+PTT 2.6 x 6)
4 CNP301
9
CDX-F7000/F7005X/FW700
2-3. MAIN BOARD 6 cord 2 two screws (+PTT 2.6 x 8)
1 three ground point screws (+PTT 2.6 x 6)
5 two screws (+PTT 2.6 x 8) 4 CN401
3 MAIN board
2-4. CHASSIS (T) SUB ASSY
4 claw 2 two screws (+P 1.7 x 2.2) 1 two screws (+P 1.7 x 2.2)
6 chassis (T) sub assy
5 SENSOR board
3 claw
10
CDX-F7000/F7005X/FW700
2-5. ROLLER ARM ASSY
3 washer (1.1 – 2.5)
5 roller arm assy
4 worm wheel (RA)
2 spring (RAR)
1 spring (RAL)
2-6. CHASSIS (OP) ASSY
8 qa chassis (OP) assy
0 compression spring (damper)
lever (D) 4 washer 1 CN2 6 9 two compression springs (damper)
5 gear (LE1)
7
slider (R) 3 tension coil spring (KF) 2 Remove the six solderings.
11
CDX-F7000/F7005X/FW700
2-7. OPTICAL PICK-UP
2 chucking arm sub assy
5 claw
1 tension coil spring (CHKG)
7 optical pick-up
6 main shaft
4 rack (SL) 3 screw (+B 1.4 x 5)
2-8. SL MOTOR ASSY (M902)
1 screw (+P 1.4 x 1.8)
2 SL motor assy (M902)
12
CDX-F7000/F7005X/FW700
2-9. LE MOTOR ASSY (M903)
8 screw (+M 1.7 x 2.5)
0 woam (LEB) assy
9 bearing (LEB)
qf two toothed lock screws (+M 1.4 )
2 washer
qa screw (+M 1.7 x 2.5)
3 gear (LE1)
lever (D)
4
bracket (LEM) qs screw (+M 1.7 x 2.5)
qd
qg LE motor assy (M903)
5
6 screw (+P 1.7 x 2.2)
slider (R) 7 leaf spring (LE) 1 Remove the soldering.
2-10. SERVO BOARD
1 Remove the eight solderings.
6 SERVO board
2 Remove the three solderings. 4 toothed lock screw (M 1.7)
5 claw
3 CN2
13
CDX-F7000/F7005X/FW700 SECTION 3 DIAGRAMS 3-1. IC PIN DESCRIPTIONS • IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name I/O Pin Description 1 LD O Laser diode ON/OFF control signal output (L: laser OFF, H: laser ON)
14
2 3
PD PN
I I
Dimmer monitor input from optical pick-up laser diode. Not used. (Fixed at L in this set)
4 5
AVDD DGND
— —
Analog power supply pin (+3.3 V) Ground
6 7
RFOK INTQ
O O
RFOK signal output to system control IC. CD text pack synchronization signal output to system control IC.
8
RST
I
9
A0
I
CD reset signal input from system control IC. Command/parameter discrimination signal input from system control IC.
10
STB
I
(L: command transmission, H: parameter transmission) Data strobe signal input from system control IC.
11 12
SCK SO
I O
Serial clock input from system control IC. Serial data output to system control IC.
13 14
SI DVDD
I —
Serial data input from system control IC. Power supply pin (+3.3 V)
15 16
DAVDD ROUT
— O
D/A converter power supply (+) pin (+3.3 V) Analog audio signal output (R-ch)
17 18
DAGND REGC
— —
Ground Capacitor connection pin for SCF regulator.
19 20
DAGND LOUT
— O
Ground Analog audio signal output (L-ch)
21 22 23
DAVDD XVDD XTAL
— — O
D/A converter power supply (+) pin (+3.3 V) Power supply pin (+3.3 V) Main system clock output (16.9344 MHz)
24 25
XTAL XGND
I —
Main system clock input (16.9344 MHz) Ground
26 27
DVDD C1D1/FZD
— O
Power supply pin (+3.3 V) Not used. (Open)
28 29
C1D2/TZD C2D1/RMUTE
O O
Not used. (Open) CD R-ch data zero detection signal output
30 31
C2D2/LMUTE C2D3/SHOCK/SBSY
O O
CD L-ch data zero detection signal output Not used. (Open)
32 33
LOCK/FR WFCK/MIRR
O O
Not used. (Open) Not used. (Open)
34 35
RFCK/HOLD PLCK
O O
Not used. (Open) Not used. (Open)
36 37
C16M DGND
O —
Not used. (Open) Ground
38 39
TX EMPH/RAMOVER
O O
Not used. (Open) Not used. (Open)
40 41
FLAG DVDD
O —
Not used. (Open) Power supply pin (+3.3 V)
42
LIMIT
I
43
XTALEN
I
44
DGND
—
(Fixed at L in this set) Ground
45 46
DIN DOUT
I O
Not used. (Connect to DOUT in this set) Not used. (Connect to DIN in this set)
47 48
SCKIN SCKO
I O
Not used. (Connect to SCKO in this set) Not used. (Connect to SCKIN in this set)
49
LRCKIN
I
Not used. (Connect to LRCK in this set)
Not used. (Fixed at L in this set) Oscillation circuit ON/OFF control signal input (L: ON, H: OFF)
CDX-F7000/F7005X/FW700
Pin No. 50
Pin Name LRCK
I/O O
Pin Description Not used. (Connect to LRCKIN in this set)
51 52
DVDD FD+
— O
Power supply pin (+3.3 V) Focus servo drive PWM signal output (+)
53 54
FD– TD+
O O
Focus servo drive PWM signal output (–) Tracking servo drive PWM signal output (+)
55 56
TD– SD+
O O
Tracking servo drive PWM signal output (–) Sled servo drive PWM signal output (+)
57 58
SD– MD+
O O
Sled servo drive PWM signal output (–) Spindle servo drive PWM signal output (+)
59 60
MD– DGND
O —
Spindle servo drive PWM signal output (–) Ground
61 62 to 66
TESTEN TEST4 to TEST0
I I
67 68
ADGND EFM
— O
A/D converter power supply (–) pin EFM signal output
69 70
ASY ADVDD
I —
EFM comparator reference voltage input A/D converter power supply pin (+3.3 V)
71 72
RFI EQ2
I —
RF signal input for EFM data growing. Not used. (Open)
73 74
EQ1 RF–
— I
RF amplifier equalizer parts connection pin Not used. (Open)
75 76
RF2– AGCO
I O
RF amplifier inversion input RF signal output after on AGC.
77 78 79
AGCI RFO ATEST
I O I
RF AGC signal amplifier input RF signal output before on AGC. Not used. (Open)
80 81
C3T AGND
— —
Capacitor connection pin for 3T detection. Ground
82 83
A C
I I
Signal input (A) from optical pick-up detector. Signal input (C) from optical pick-up detector.
84 85
B D
I I
Signal input (B) from optical pick-up detector. Signal input (D) from optical pick-up detector.
86 87
F E
I I
Signal input (F) from optical pick-up detector. Signal input (E) from optical pick-up detector.
88 89
VREFIN AVDD
I —
Reference voltage (+1.65 V) input Analog power supply pin (+3.3 V)
90 91
REFOUT REFC
O —
Reference voltage (+1.65 V) output Capacitor connection pin for reference voltage output.
92 93
FE– FEO
I O
Focus error signal amplifier inversion input Focus error signal amplifier output
94 95
ADCIN TE-
I I
Not used. (Open) Tracking error signal amplifier inversion input
96 97
TEO TE2
O O
Tracking error signal amplifier before output Tracking error signal amplifier after output
98 99
TEC AGND
I —
Tracking error signal comparator input Ground
100
PWMSW
I
Test setting input (Fixed at L in this set) Test setting input (Fixed at L in this set)
Not used. (Fixed at L in this set)
15
CDX-F7000/F7005X/FW700
• IC303 M30624MGP (SYSTEM CONTROL) (MAIN BOARD (3/3)) Pin No. Pin Name I/O 1 SIRCS I Remocon data input
16
Pin Description
2 3
(NCO) CD SO/TSO
O O
Not used CD servo serial data output
4 5
CD SI/TSI CD CKO/TCKO
I O
CD servo serial data input CD servo serial clock output
6 7
BYTE CNVSS
I I
Connecting to ground. Flash write-in signal input
8 9
XCIN XCOUT
I O
Sub clock signal input (32.768kHz) Sub clock signal output (32.768kHz)
10 11
RESET XOUT
I O
CPU reset input Main clock signal output (6MHz)
12 13
VSS XIN
— I
Ground Main clock signal input (6MHz)
14 15
VCC1 NMI
— I
Ground Non maskable interrupt signal input
16 17
CD INTQ DAVN
I I
CD-TEXT sync. signal input RDS data block sync. detection signal input
18 19
BU IN NS MASK
I O
Back-up power detection signal input NS-MASK signal output
20 21
BEEP FSW IN
O I
Beep signal output DD converter OSC frequency count input
22 23
FSW OUT SA CLK
O O
DD converter OSC frequency change output Spectrum analyzer clock output
24 25 26
TEL ATT ATT VOL ATT
I O O
Telephone mute signal input Mute signal output Electronic volume mute signal output
27 28
I2C CKO I2C SIO
O O
I2C bus serial clock output I2C bus serial data output
29 30
UNI SO UNI SI
O I
SONY bus serial data output SONY bus serial data input
31 32
UNI CKO TUNER ATT
O O
SONY bus serial clock output Tuner mute signal output
33 34
EE SIO EE CKO
I/O O
35 36
RE IN0 RE IN1
I I
Rotary encoder signal input 0 Rotary encoder signal input 1
37 38
NOSE SW DOOR SW
I I
Front panel detection signal input Panel open detection signal input
39 40
HOLD AMP DIAG
I I
External bus data input (HOLD) AMP self-diagnosis function control signal input
41 42
AMP STB (NCO)
O O
AMP standby signal output Not used
43 44
(NCO) WRI/WR
O I
Not used External bus data input (WRI/WR)
45 46
CD LIMIT CD D SW
I I
CD LIMIT switch detection signal input CD D switch detection signal input
47 48
CD IN SW 4V SEL
I I
CD IN switch detection signal input 4V PRE-OUT select signal input
49 50
MP3 SEL DST SEL1
I I
Deck mechanism select signal input Destination select setting pin 1
51 52
DST SEL2 CD LM LOAD
I O
Destination select setting pin 2 CD loading signal output
Tuner pack EEPROM serial data input/output Tuner pack EEPROM serial clock output
CDX-F7000/F7005X/FW700
Pin No. 53
Pin Name CD LM EJECT
I/O O
Pin Description CD eject signal output
54 55
CD RESET CD AO
O O
CD reset signal output CD AO signal output
56 57
CD STB (NCO)
O O
CD strobe signal output Not used
58 59
CD RF OK CD ON
I I
CD RF OK signal input CD ON signal input
60 61
VCC2 DISP RESET
— O
Power supply pin (+5V) Display CPU reset signal output
62 63
VSS TEST IN
— I
Ground Test mode signal input
64 65
BUS ON SYS RST
O O
BUS ON signal output System reset signal output
66 67
BUS/AUX (NCO)
O O
BUS AUDIO/AUX-IN select signal output Not used
68 69
ACC IN ILL IN
I I
ACC power supply check signal input ILL check signal input
70 71
RC IN1 CDM ON
I I
Rotary commander signal input CD power supply ON signal input
72 73
CD SELF SW TU ATT IN
I I
CD SELF switch detection signal input Tuner attenuator zero cross signal input
74 75
ZERO DET1 ZERO DET2
I I
ZERO detection signal input 1 ZERO detection signal input 2
76 77 78
Z ATT (NCO) (NCO)
I O O
Z mute signal input Not used Not used
79 80
ROMC EN QUALITY
O I
Connecting to ground. Tuner noise detection signal input
81 82
MPTH VSM
O I
Not used S-meter signal input
83 84
SA IN KEY IN1
I I
Spectrum analyzer data input Key signal input
85 86
KEY IN0 RC IN0
I I
Key signal input Rotary commander signal input
87 88
KEY ACK2 KEY ACK0
I I
Rotary commander ACK signal input Key ACK signal input
89 90
KEY ACK1 DOORING
I O
Key ACK signal input Sub panel LED power supply control signal output
91 92
RAM BU FLD ON
I O
RAM back-up input FL driver power supply control signal output
93 94
FL ON AVSS
O —
FL power supply control signal output Ground
95 96
DISP CE VREF
O —
Display CPU chip enable output AD converter reference voltage (+5V)
97 98
AVCC DISP SI/RX
— I
Power supply pin (+5V) Display CPU serial data input
99 100
DISP SO/TX DISP CKO
O O
Display CPU serial data output Display CPU serial clock output
17
CDX-F7000/F7005X/FW700
• IC901 M30823MH-080GP (DISPLAY CONTROL) (KEY BOARD) Pin No. Pin Name I/O 1 SYS CE I Main chip enable input
Pin Description
2 3
(NCO) FL DAT3
O O
Not used FL serial data output 3
4 5
(NCO) FL CLK IN
O I
Not used FL serial clock input
6 7
BYTE CNVSS
I I
Connecting to ground. Flash write-in signal input
8 9
PLL LPF PLL GND
O I
PLL low pass filter connection pin Ground
10 11
RESET XOUT
I O
CPU reset input Main clock signal output (8MHz)
12 13
VSS XIN
— I
Ground Main clock signal input (8MHz)
14 15
VCC NMI
— I
Power supply pin (+5V) Non maskable interrupt signal input
16 17
(NCO) GCP IN
O I
Not used GCP pulse interrupt signal input
18, 19 20
(NCO) GCP OUT
O O
Not used GCP pulse signal output
21 22
LAT BK
O O
FL data LAT output FL BK signal output
23 24
GCP2 (NCO)
O O
FL GCP signal output 2 Not used
25 26 27
GCP1 (NCO) GCP4
O O O
FL GCP signal output 1 Not used FL GCP signal output 4
28 29
GCP3 SYS SO
O O
FL GCP signal output 3 Main bus serial data output
30 31
SYS SI SYS CLK
I O
Main bus serial data input Main bus serial clock output
32 33
(NCO) FL DAT1
O O
Not used FL serial data output 1
34 35
(NCO) FL CLK
O O
Not used FL serial clock output
36 to 38 39
(NCO) HOLD
O I
Not used External bus data input (HOLD)
40 to 43 44
(NCO) WRI/WR
O I
Not used External bus data input (WRI/WR)
45 to 59 60
(NCO) VCC
O —
Not used Power supply pin (+5V)
61 62
(NCO) VSS
O —
Not used Ground
63 to 93 94
(NCO) AVSS
O —
Not used Ground
95 96
(NCO) VREF
O —
Not used Reference voltage (+5V)
97 98
AVCC (NCO)
— —
Power supply pin (+5V) Not used
99 100
FL DAT2 FL CLK IN
O I
FL serial data output 2 FL serial clock input
18
CDX-F7000/F7005X/FW700
3-2. BLOCK DIAGRAM — CD SECTION —
RF AMP,DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR IC1
OPTICAL PICK-UP (KSS1000E)
82
83
A
C RF EQ
B 84
LOUT 20 ROUT 16
D/A CONV
EFM DEMOD
D
I-V CONV.
INTQ
85
SI SO
FORCUS ERROR
SCK
I/F
STB A0
E 87 86 PD
2
F PD
RST
TRACKING ERROR
SERVO CTL
RFOK
LD AMP
OSC
LD
1
LD
CDL
FOCUS/TRACKING COIL DRIVE, SLED/SPINDLE/LOADING MOTOR DRIVE IC2
12
FOCUS COIL
11
13
TRACKING COIL
14
7
16 CD_INTQ
13 12
3 CD_SO IC251 (1/3) 6
M901 (SPINDLE)
M903 (LOADING)
M
-
15 16
+
M
-
17 18
+
2
4 CD_SI
11
5 CD_CKO
10
56 CD_STB
9
55 CD_A0
8
54 CD RESET
6
58 CD_RFOK IC251 (2/3) 1 7
74 ZERO DET1 3
RMUTE 29
FSC+ FSC-
TRK+ TRK-
FOCUS COIL DRIVE
FD+ 5 FD6
TRACKING COIL DRIVE
TD+ 2 TD3
23
5
75 ZERO DET2
24
X1 16.9344MHz SW3 (DISC IN) SW2 (SELF) SW4 (LIMIT)
+
SYSTEM CONTROL IC303 (1/3)
IC251 (3/3) 52 53 54 55 56 57 58 59
M902 (SLED)
A
R-CH
LMUTE 30
FD+ FDTD+ TDSD+ SDMD+ MD-
LD DRIVE Q1
(Page 20) TUNER SECTION
M
-
9 10
SLSL+
SPSP+
LDLD+
SLED MOTOR DRIVE
SD+ 27 SD26
SPINDLE MOTOR DRIVE
MD+ 24 MD23
LOADING MOTOR DRIVE
LOAD EJECT
SW1 (DOWN)
47 CD_INSW
72 CD_SELFSW
45 CD_LIMIT
46 CD_DSW
1
52 CD_LM_LOAD
28
53 CD_LM_EJECT A3.3V
CD+3.3V
R-CH is omitted due to same as L-CH Signal path
AU3.3V D3.3V DR6V
: CD CD+6V
19
19
CDX-F7000/F7005X/FW700
3-3. BLOCK DIAGRAM — MAIN SECTION —
CN401 SUB OUT(MONO) MUTE Q470
ELECTRONIC VOLUME IC401
(Page 19)
CD SECTION
A
PB LCH 4 PB RCH 7 OUTSW 17
CD-L R-CH
GROUND SW Q408 L
R-CH
42 CD LCH 43 CD RCH
L
L
TUX501 (TUNER UNIT)
OUT RF 22 OUT RR 21
L 4 R 3
1 ANT
R-CH
40 TUNER LCH 41 TUNER RCH OUT LF 25
12 INFL
OUT LR 24
11 INRL
TU-SCL 13 TU-SDA 14
AU+8V
MUTE 15
TU+5V BU+5V
SCL 13 SDA 12
MUTE Q171 SCL SDA MUTE CONTROL Q401,402
10
D401
R-CH
5 AMP-REM 6 ANT-REM
SW1 29 SW2 27 SDA SCL
SCL SDA
82 VSM VOL ATT 26 32 TUNER ATT ATT 25 34 EEP SCL BEEP 20 33 EEP SIO AMP STB 41 73 TU ATTIN AMP DIAG 40 SA IN 83 SA CLK 23 BUS/AUX 66
F901 2 SDA 4 SCL
BATT
REG1 REG2 REG3 REG4 REG5
16 ACGND 22 STB 25 DIAG BATT
30 37 31 33 34
35 VP
ACC CHECK Q102
7
TEL ATT 24
TEL ATT Q103
13 15
TU+5V
: CD PLAY : FM
BATT 3 BU IN UNI SI UNI SO UNI CKO BUS ON SYS RST
14
ILL CHECK Q907
ILL IN 69
BUS INTERFACE IC110
18 30 29 31 64 65
10 8 9 11 12 13
B CHK DATA OUT DATA IN CLK IN BUSON RST
TU+5V REG Q501
ACC
ATT TEST ILL
AU+8V CNP102
BATT DET Q101
8
D105 BATT
6
3
DATA I/O 6
5
2
CLK 4
4
BUS ON 1 RST 2
TH100
20
1 7
BATT
20
BATT
AU+8V BU+5V CD+3.3V CD+6V ILL+B
TEST IN 63
: AM
16
ACC IN 68
• R-CH is omitted due to same as L-CH. • Signal Path
RL+ RL-
4 FR+ 12 FR3 RR+ 11 RR-
BATT
SYSTEM CONTROL IC303 (2/3) IIC SCK 27 IIC SIO 28
E2P SCL 16 E2P SDA 17 MUTE CONDITION 8
2
RL+ 9 RL- 7
SCL SDA
S-METER 6 TU MUTE 7
CNP101 1 FL+ 9 FL-
FL+ 5 FL- 3
MUTE Q181
PJ401
FRONT AUDIO OUT
R
R-CH
CONTROLLED POWER AMP/ MULTIPLE VOLTAGE REGULATOR IC201
SA IN 14 SA OUT 16 VCC 10 TU VDD 11 E2P VDD 15
REAR AUDIO OUT
R
R-CH
J601 (ANTENNA)
BUS AUDIO IN
R
R-CH
BUS CONTROL IN
CDX-F7000/F7005X/FW700
3-4. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL IC303 (3/3) ROTARY ENCODER ENC901(1/2)
DISPLAY CONTROL IC901 FL DAT1 33 FL DAT2 99 FL DAT3 3 LAT 21 BK 22 FL CLK 35
35 REIN0 36 REIN1
KEY MATRIX S901-910,912 LSW901-908 ENC901(2/2)
85 KEYIN0 84 KEYIN1
DISP CE 95 DISP SI 98 DISP SO 99 DISP CKO 100
1 30 29 31
CNVSS 7
CE SI SO CLK CE
7 CNVSS GCP1 GCP2 GCP3 GCP4
88 KEY ACKO 89 KEY ACK1
6 5 4 12 13 7
DISP RESET 61
10 RESET
25 23 28 27
4 5 1 2
11
GCP
FL900 FLUORESCENT INDICATOR TUBE 11
GCP BUFFER IC902
87 KEY ACK2 RESET IC904
1 70 RCIN1 86 RCIN0
CNJ101 (REMOTE IN)
ILL+B LED901,910-914 LSW901-908
POWER CONTROL Q601,602
BATT
DOOR IND 90
BU+5V
2 IN
LED931,932
REMOTE CONTROL SIGNAL RECEIVER IC903
RESET IC302
OUT 1
10 RESET
+5V REG D911
ILL+B
1 VCC
S301 RESET SIRCS 1
2 OUT
IR
37 NOSE SW S300 (NOSE DET)
XOUT 11 XIN 13
X301 32.768kHz
8 XCIN 9 XCOUT
X302 6MHz
POWER CONTROL Q914,916
ILL+B
+5V REG Q915
FL VDD+5V
FLD ON 92 FL ON 93 T620 BATT
FSW OUT 22
POWER CONTROL Q623,Q624
DC-DC CONVERTER CONTROL Q621,622
D623,624
5 VCC 7 CT
OUT 4
IN 65
FSW IN 21
21
21
FL+4.3V
DC-DC CONVERTER IC620
D620,621 FL+1V ON/OFF DRIVE Q620
FL+55V D622
CDX-F7000/F7005X/FW700
3-5. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
3-6. WAVEFORMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
— Servo Board —
1
For schematic diagrams.
For printed wiring boards.
Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. f : internal component. • • C : panel designation.
Note: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. a : Through hole. • • : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • • • • • •
•
•
• •
•
Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
A : B+ Line. B : B– Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. CD mechanism section no mark : CD PLAY Main (1/3), (2/3), (3/3) and Key sections no mark : FM ( ) : AM < > : CD PLAY ∗ : Impossible to measure Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD PLAY F : FM f : AM Abbreviation CND : Canadian model.
— Main Board —
(MODE: CD PLAY)
Caution: Pattern face side: (Side B) Parts face side: (Side A)
1 1.2Vp-p
16.9344MHz
IC1
wd
32.768kHz
(XTAL)
IC303
2
9
(XCOUT)
2 5Vp-p
1.6Vp-p
Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
6MHz
IC1
IC303
(AGCI)
uj
qa
(XOUT)
3
C Q
2.9Vp-p
0V
These are omitted
Approx. 620mVp-p
B E
IC1
od
(FEO)
4 0V
BE C These are omitted
Approx. 200mVp-p
IC1
oh
(TEO)
ECB These are omitted • Abbreviation CND : Canadian model.
3-7. CIRCUIT BOARDS LOCATION
SERVO board SENSOR board
tuner unit (TUX501) MAIN board KEY board SUB board
22
22
CDX-F7000/F7005X/FW700
3-8. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 22 for Circuit Boards Location.
2
1
3
4
5
6
7
: Uses unleaded solder.
8
9
10
11
12
13
14
A
C11
C1 C32
C2
C29
C31
JR90
R45
C7
C30
X1
JR91
B
R44
R42 C5
R41
C8
C3
C6
C28
C13
R11
C38
R13
C36 R1
C27
R14
CN1
(Page 29)
2
C34
C79 R85 R84
C71 C70
R82 R80 R81 R78
R79
C72
IC2
C74
R73 R71
R75
SW3
R83
C76 C77 C78
F
C75
R77
R76
R74
C73
E
R72
R70
FB1
R9
C19 C18
CNP301
CN
D
R12
C35
R15 C39
C37
C25
C23
C17
JR41
R6 R7 C20 C21
Q1
C26
JR40
C
IC1
SW2
SW1 1-688-288-
G
23
23
CDX-F7000/F7005X/FW700 • Refer to page 22 for Waveforms. 3-9. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 34 for IC Block Diagram.
C20
R9 C25
Q1
R13
TP32
C23
R7
C21
C19
TP19 CN2
C18
C17
R6
TP33
R14 R15
C36
TP31 C38
C37
TP30
TP20 C26
C39
TP29 TP14
TP21
C35
R12
C27
TP28 TP27 C34
R1
TP26 TP13
R11 C28
C13
TP12
IC1
TP11
TP22
TP10 C29
TP9
TP23
TP8 C30
TP25
TP7 TP6
TP24
TP5 TP4 TP3
C31 SW4
TP2
TP81 TP80
C32
TP1
CN1 C11
TP65
JR90
JR91
TP64 TP63 TP62 M901
TP85
TP61
TP83 TP84 M902
TP60
C1
TP82
C5
X1
C8
R45
TP59
R44
TP58 TP57
C3
C6
TP56
FB1
TP55
C2
TP54 TP48
C7 TP27
TP87
TP28
TP88
TP29
TP89
SW3
R41 JR41
TP52
JR40
TP53
TP51 TP49 TP50
R42
TP47
SW2
TP46 TP45 TP44
SW1
TP43
TP90
TP42
TP91
TP41 TP40
IC2
C79
R85
R84
C78
R83
R82
C72
C77
R81 R80
C73
C76
R79 R78
R70
R71
C70
R72
R73
C71
R74
R75
R76
R77
IC B/D
TP100 C74 TP75 M903
TP92 TP74
TP93 TP71 TP70 TP73 TP72 C75
24
24
(Page 27)
CDX-F7000/F7005X/FW700
3-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 34 for IC Block Diagram.
TUX501
FB442 R478
C508
CN401
C442
C443 R402
FB441
R502
J601
R407
Q470
L503 C509 C507
R504
C510 C278 R272
C273 R274
R429
C178 R275
Q271 R282 Q501
R431
C288
Q281
L502
C283
R285
PJ401
C188 R243 R242
R284
R410
C242 C142
C502
R501
C501
R143 R142
C511
D501
R172
R435
C173 R174 R175
Q171
C512 R182
C420
R424
Q181
R433
D122
C183
R184
R444
C418
R446
R443
R185
C419
Q408 R408 C199
C309 R445 C417
C308
C416
IC B/D
C421 C433
R426 C422
C434
L401 Q402
C424 R414
D401
R401
C423 R415
C435
D403 C425
IC401
R416
Q401 C403
R403
R417 C427
C426
C428
C429
C401
(Page 26)
R418
C432
R421
R419
R420
C430 R422
C431
(Page 27)
25
25
CDX-F7000/F7005X/FW700 3-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 34 for IC Block Diagram.
C215
C210
C205
IC B/D D111 D110
CNP101
D113 C206
R203
C218
R205
D112
CN103
CN102
C216
C208
D114 C209 C219
R206
C207
R204
C217
IC201
D115
D116
D117 D118 D120
D119
D121 R201 C201
C203
R202
C202
F901
R103 C211 C212 C221
C204
R111
Q103
Q907
D106 R921
C223 R110
R922
R112
D909
C214 R109
R929
D108
C903
R920
C226 R107 C225
R105
Q102 R104
C106
C103
D123
C102 R108
R106
L101
D109
(Page 25)
R116
CNJ101
R643
CN602
R642 Q915
R634 L901
Q914 R950
Q624 R635
CN603
Q623
R949
D911
C901
C928 D910
Q916
C930
C623 D624
Q621 R627
R626
R628
C624
C620 D623
R625 D625
R629
CN601
T620
L620
D622
R621
R620
C622 D620
C629
C628
R622
C621 D621
Q622 IC620 R623
IC B/D R630
D626 R631
Q601 C626
C627
R601
R602
R603 D606
D605 D604
Q602
D601
R632
D603
D627
R624
D602
R633
(Page 31)
Q620 R636
C625
R600
(Page 27)
26
26
CDX-F7000/F7005X/FW700 • Refer to page 22 for Waveforms. 3-12. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 35 for IC Block Diagram.
(Page 25)
(Page 26)
(Page 24)
CNP301
R240 FB327
R253
L303 C335 C342
R904
R250
C336
FB326
R251
FB329 FB325
FB328 R241 FB330
R366
R370
C341
R910
R323
R322
R345
R344
R343
R341
R365
R346
R302
R381
R314
R368
R360 C333
C306 C334 C307 C304
C303 R363 R254
L301
L302
R255 R256 R257 R258 R391 R259 R312 IC251
C321
R252
C319 R364
R377 D306
R342
C322 IC303 C317
X302 C332
C323 C315
X301
R393 C316
R311
R304 R265 R264
R260
R263 R261 R102
R262
D105
Q101
TH100
D102
D104
D103
D101
IC B/D R101
L320
C101
IC110 R115 R113
C110 C111
JR302
R117
C320
R330 C330 R333
R351
C318
R335
R350
R114 R332
R319 R357
D305
CNP102 R119
D907
R326
R356
R367
R301 S301
C313
R300 S300
IC302 C312
27
27
C311
CDX-F7000/F7005X/FW700 3-13. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 22 for Circuit Boards Location.
14
13
12
11
10
9
: Uses unleaded solder.
8
7
6
5
4
3
2
1 A
• Semiconductor Location
B
C219
C217 R113
R204 C207
R203
D106
C216
Q470
R407 R402
R205 C218
C
R446
Q401
Q402
R433
R272 R282
C403 L401
L303
L301
L302
Q623
R634
Q624
R435
R431
R429
Q907
Q102
D
E
L502
Q101
Q103
R172 R182
R106
R929 R921
R401
R105
D401
D104
R922
D403 R403
IC110
R111 R112
R107 R920 R108
R104
D101
D909
R101 R102
R445
D-9 E-9 F-5 G-5 F-3 G-9
IC251
R368
R119 R256
R625 R377
C416
C417
R417
F
R426
C201
R414
C430
R201
C421 R416
C424
R257
R628
IC303
R391 R258 D306
Q622
C511
R627
G
R631
C625 R630
R260
C627
R261
R633 R632
R262
D627 D626
CN603
R636
C626
IC620
R363
Q620
D624
Q916
H
Q914 R950 L901
R356 R357
CN602
R350
D623 T620
R949
R311
C330
D622
R351 R333
Q621
R304
R415
R370 R360
R254 R255
R421 R420 R341
FB330
IC302
R250 R302 R366 R346
R253 R314 R251 R381
L620
R393
R367
IC401
I R332 D620
Q601 R300
D621
R301
R629
D-8 E-9 D-6 C-3 C-2 C-3 C-3 E-6 E-6 C-2 I-3 J-3 H-9 G-10 G-9 E-9 E-10 E-6 H-3 H-3
Q181
R444
R635
Q101 Q102 Q103 Q171 Q181 Q271 Q281 Q401 Q402 Q470 Q601 Q602 Q620 Q621 Q622 Q623 Q624 Q907 Q914 Q916
Q281
C206
R206
D111
Q271 Q171
R424
C209
C208 R103
R443
R116
D105
IC110 IC251 IC302 IC303 IC401 IC620
Location D-9 D-8 D-8 C-8 C-6 G-6 E-5 E-6 I-8 I-9 H-8 H-8 H-8 H-9 H-9 D-7
R115 R114
Ref. No. D101 D104 D105 D106 D111 D306 D401 D403 D620 D621 D622 D623 D624 D626 D627 D909
R601 R602 R603
Q602
J
28
28
CDX-F7000/F7005X/FW700
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PJ401
A
CNJ101
J601 CNP102
C278
C178
R408
C242
D110
CNP101
C211 F901
C205
C210
C288
Q408
C142
B
C188
D122
C199
C215
D112 IC201
R275
C212
TH100
C443
C221
D108
D109
D123
C103
C106 C223
C226
C203
R202
R110
C435
L101 R117
R109
C111
R642
C110
C102
C903 C401
C434
C419 R502
E
R643
• Semiconductor Location
C418
C420
C341
R241
R252
C334 C307
C333 C306
FB327
(Page 23)
R343 C319
C629
C322
R364 R312 C317
R330
X302
C332
C623
JR302 C318
C315
R344
R342
X301
C316
R265
R335 D907
R263
Q915
D305 R264
D910
D606
C928
C901
D601 D604
R622
R326
C621
R345 D911
C320
H
R623 R621 R620
R319
R624
C930 C620
S300
J
D605
CN601 R600
S301 D603
D602
(Page 30)
29
C624
R626
C323
G
D625
C622
R910
C628
C303
R322
C425
C501
FB328
R323
C304
D501
C342
R365
C428
FB326
C336 R240
R259
C502
R418 C427
C309
C335
C313
C432
C509 C510
R419
R501
R504
F
Q501
C507
R904 L320
FB325
CNP301
C431 R422
C423
C308
C321
C508 L503
C311
C312
C429
FB329
C422 C426
I
C101
D118
C442
R478
C433
D116 D115
C214 C202
D
D120
D117
D119
FB441
TUX501
D121 C225
CN401 FB442
CN102
D113
C
D102 D103
R174
C173
R284
C283
R184
R243
C183
R143
CN103
C204
R142
R274
R175
D114
R185
C273
R242
R285
R410
29
Ref. No. D102 D103 D108 D109 D110 D112 D113 D114 D115 D116 D117 D118 D119 D120 D121 D122 D123 D305 D501 D601 D602 D603 D604 D605 D606 D625 D907 D910 D911
Location B-10 C-10 D-8 D-9 B-8 B-8 C-7 C-6 C-8 C-9 C-8 C-6 C-6 C-6 C-6 B-3 D-9 H-8 F-3 I-3 J-3 J-3 I-3 J-3 I-2 G-11 H-8 H-4 H-4
IC201
B-6
Q408 Q501 Q915
B-3 F-2 H-4
CDX-F7000/F7005X/FW700
3-14. PRINTED WIRING BOARD — SUB SECTION — • Refer to page 22 for Circuit Boards Location.
1
2
3
4
5
6
: Uses unleaded solder.
7
8
9 (Page 32)
A
B
D991
LED932
C
CNP501
R991 R990
LED931 D990
S901
D
E (Page 29)
F
G
H
I
J 30
30
10
CDX-F7000/F7005X/FW700
3-15. SCHEMATIC DIAGRAM — SUB SECTION —
CNP501
(Page 33) (Page 26)
R990 D991
S901
LED932
31
D990
LED931
31
R991
CDX-F7000/F7005X/FW700
3-16. PRINTED WIRING BOARD — KEY SECTION — • Refer to page 22 for Circuit Boards Location.
LED919
5
6
7
8
9
10
11
12
13
14
S905
LED923
S907 LED920
LED917
D916
A
4
LED918
3
LED914
2
1
: Uses unleaded solder.
B
IC903
D917
S908 D915
LED915 S904
LED913
S912 LED911 LED901
S909
C S906
S902
S910
LED910
D
LED916
D918
22
LE
D9
D9
LE
21
LED912
S903
LED924 LSW901
LSW907
LSW908
LSW906
LSW905
LSW904
LSW902
LSW903
(Page 30)
E
R916 R922
R970
I
R958
R907
C916
C906
(
Location G-9 H-9 G-9 F-3 G-12 G-12 H-14 G-10
Ref. No. D913 D914 (D915) (D916) (D917) (D918) (D919)
Location H-13 H-13 B-4 A-2 B-1 D-2 G-9
Ref. No. IC901 IC902 IC903 IC904
Location G-8 H-9 B-14 G-11
LED901 LED910 LED911
C-14 D-4 C-5
Ref. No. LED912 LED913 LED914 LED915 LED916 LED917 LED918 LED919
Location C-5 C-4 A-3 C-1 D-3 B-5 A-4 B-2
Ref. No. LED920 LED921 LED922 LED923 LED924
Location B-3 C-3 C-2 A-13 D-7
): CDX-F7000/FW700 only
32
32
D910
R919 CN901
D914
R977 C918
R976
R981 R980 R979
IC902
FB901 C905
• Semiconductor Location Ref. No. D901 D902 D903 D904 D909 D910 D911 D912
FB904 FB903 FB902
C903 R947 R946
FL900
C909
R961 L901
C912
C904
X901
R959
D911
R906
R973
D913
C901
FMB12
R975
R983
FB920
R928
R908
R905 R934
R909
FB907 FB906 FB905
R929
R904
R935
H
R932
D901 D902
FB908
C913
R903
R937
R954 D903
FB909
FB919
R902
FB917
FB913 FB914
C915
R984
R933
R936
FB911 FB910
IC901
R960
R985
R930 R931
FB916 R982 FB918
R938
FB915
G
R921
IC904
R939
D912
R972
R987 C917
D919
R912
R913
R920
R923
C907
FB912
FMB11
R911
R924
R955 R953 R971
R901
R927
D904 ENC901
R926
R925
F
R915 R914
R918
R917
R978
D909
R910
15
CDX-F7000/F7005X/FW700
3-17. SCHEMATIC DIAGRAM — KEY SECTION —
ENC901(1/2)
CN901
R979
R980
R981 R918
R919 R920
R921 R922
LSW903(2/2)
LSW904(2/2)
R923
R924
R925 R926
R927 R983
LSW905(2/2)
LSW907(2/2)
LSW901(2/2)
LED924
LSW906(2/2)
LSW908(2/2)
R984
C901 LED923
D901
LED901
LSW902(2/2)
D902
LED910
FB912
D903 C912 D904
(Page 31)
D913
R928
R929
R930
R931 R932
R933
R934
R935
R936
R937 R938
LED911 LED913
D910
LED915
D917
LED917
D909
D915
R955 LED919
LED921
LED920
LED922
C903 LED912
LED914
R954
IC901
FB911 R977
IC903
R901
FB910
D912
R987
FB909 FB913
FB906
R947 R903
ENC901(2/2)
LSW901(1/2)
S903
S912
R910
FB903
LSW902(1/2)
S905
LSW903(1/2)
R912
R913
FB901
C906
S906
LSW904(1/2)
S907
LSW905(1/2)
S908
LSW906(1/2)
S909
LSW907(1/2)
R914
R906
FB902
X901
C905
R905
S904
R975
FB920
C915
R982 C916
R970
R973
R971
FB919
FB904 FB917
R911
R946 R904
FB918
FB915
FB905
FB916
C917
D911
IC904
S910
FB907 FB914
C904
R902
FB908
R976
S902
R907
R915
IC902
R972 D919
R908
C913
R916
R960
C907
R909 R959
R917
R958 LSW908(1/2)
C909 R961 L901
FL900
33
33
R978
LED916
D918
LED918 R953
D914
D916
C918
R939
R985
CDX-F7000/F7005X/FW700
REV
OPIN4(+)
OPIN4(–)
OPOUT4
OPIN3(+)
OPIN3(–)
OPOUT3
MUTE
BIAS
GND
VO3(–)
VO3(+)
VO4(–)
VO4(+)
28
27
26
25
24
23
22
21
20
19
18
17
16
15
MUTE
–
+
–
+
–
+
LOADING DRIVER REV
–
–
+ – LEVEL SHIFT
– +
–
+
+
+
–
+ LEVEL SHIFT
+
NC ACOUT-R ACIN-SW ACOUT-SW
–
VREFOUT VDD
AC2IN-L AC2OUT-L FILOL
OUT-LF
OUT-LR
33
32
31
30 29
28 27 26
25
24 23
OUT R
MIXER
SOFT STEP FADER
34 35 36 37
SOFT STEP FADER HIGH PASS FILTER SUB WOOFER FILTER
OUT F
FWD
HIGH PASS FILTER2
MIXER
22 OUT-RF
SOFT STEP FADER
21 OUT-RR
7 BAND EQUALIXER
+ –
+
LEVEL SHIFT + –
LEVEL SHIFT +
–
SOFT STEP FADER
MAIN VOLUME
–
HIGH PASS FILTER2
SOFT STEP FADER
+
SOFT MUTE
VCC
20 AC2IN-R 19 AC2OUT-R 18 FILOR
17 OUTSW 16 SAOUT 15 MUTE
12
13
14
OPIN1(+)
OPIN1(–)
OPOUT1
OPIN2(+)
OPIN2(–)
OPOUT2
VCC
VOL(–)
VOL(+)
VO2(–)
VO2(+)
VO1(–)
VO1(+)
LOUDNESS SPECTRUM ANALIZER 14 SAIN IN-GAIN CREF 38 NC 39
TUNER-LCH TUNER-RCH CD-LCH CD-RCH AUX-L
MAIN SOURCE SELECTOR
40 41 42 43 44
REAR SELECTOR
FADER
INPUT MULTIPLEXER
II2CBUS
POWER SUPPLY
1 2 3 4 5
6 7
8
9 10 11
IC620 NJM2377M(TE2) (MAIN Board (2/3))
8
7
6
5
30µA VREF
OSC L.O U.VLO
S.C.P ER.AMP 0.52V
34
34
PWM
1
2
3
4
OUT
11
VCC
10
GND
9
NC GND NC
8
CS
7
NC PD-RCH+
6
CT
5
F.B
4
NC NC AUXR PD-LCH+ PD-
3
REF
2
IN
1 FWD
ZERO CROSS
MIC
–
+
+
–
–
–
+
+
+
–
–
NC
ACIN-L
IC2 BA5966FP-FE2 (SERVO Board)
ACOUT-L
IC401 TDA7416 (MAIN Board (1/3)) ACIN-R
3-18. IC BLOCK DIAGRAMS
13 SCL 12 SDA
CDX-F7000/F7005X/FW700
IC201 TDA8588AJ/N2 (MAIN Board (2/3))
TAB 1 2 SDA OUT FL- 3
I2C BUS 4 SCL
FL OUT FL+ 5
6 VP2 OUT RL- 7 RL
8 PGND3
OUT RL+ 9
PROTECTION DIAGNOSTIC
INRR 15
12 INFL 14 INFR
MUTE
SGND 13
10 SVR
MUTE
INRL 11
16 AC GND
VP
OUT RR+ 17 RR
18 PGND2
OUT RR- 19
20 VP1
OUT FR+ 21 FR OUT FR- 23
STANDBY MUTE
22 STB
CHIP DETECT DIAGNOSTIC
24 PGND1 TEMPERATURE PROTECTION
DIAG 25
ENABLE LOGIC 26 RST
SW2(ANT REM) 27
SWITCH
SW1(ANT REM) 29
SWITCH
28 CRES
REGULATOR
30 REG1(AUDIO +B) REG3(SERVO) 31 REG4(DR+B) 33
32 GND(REG) 34 REG5(ILL)
VP(REG) 35
REFERENCE VOLTAGE REG2(BU 5V) 37
REGULATOR
36 CBU LOADDUMP PROTECTION
BACK-UP SWITCH
IC110 MM1175XFF (MAIN Board (3/3))
BUSON 1
14 VCC
RST 2
RESET SWITCH
13 RST
BATT 3
BATT SWITCH
12 BUSON
CLK 4
11 CLK-IN
VREF 5
10 B-CHK
I/O DATA 6 GND 7
9 IN DATA 8 OUT DATA
35
CDX-F7000/F7005X/FW700 SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • -XX and -X mean standardized parts, so they may have some difference from the original one.
• Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color • Accessories are given in the last of this parts list. • Abbreviation CND : Canadian model
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
4-1. MAIN SECTION not supplied
A
MG-611XA-186//K
12
#1
#1 #2 B
A
10 F901
9 #2
8
TUX501
7
6
11
#1
not supplied
not supplied
B
5 3
4
#1
1
#1
2 4
Ref. No. 1 2 3 4 5 6 7 * 8
36
Part No.
Description
X-3384-273-1 1-828-511-11 3-246-030-01 3-261-903-01 X-3384-490-1
LOCK ASSY CABLE, FLAT (FFC) 22P BUTTON (EJECT) SCREW (+BTT 2X5) PANEL ASSY (CD), SUB
X-3384-271-1 GEAR ASSY 3-713-786-51 SCREW +P 2X3 3-246-006-31 COVER
Remark
Ref. No. 9 10 11 12 F901
not supplied (SUB board)
Part No.
Description
3-376-464-11 1-776-207-72 A-3283-429-A 1-790-375-12 1-532-877-11
SCREW (+PTT 2.6X6), GROUND POINT CORD (WITH CONNECTOR) (POWER) MAIN BOARD, COMPLETE CORD (WITH CONNECTOR) (SUB OUT (MONO)) FUSE (BLADE TYPE) (AUTO FUSE) 10A
TUX501 A-3220-959-A TUNER UNIT (TUX-032) #1 7-685-792-09 SCREW +PTT 2.6X6 (S) #2 7-685-793-09 SCREW +PTT 2.6X8 (S)
Remark
CDX-F7000/F7005X/FW700
4-2. FRONT PANEL SECTION
58 57 #3
#3 #3
FL900
56
55 not supplied
not supplied (KEY board)
not supplied
54 51 52 53
Ref. No.
Part No.
Description
51 52 53 54 54
X-3384-492-1 3-032-321-01 X-3384-635-1 X-3384-491-1 X-3385-020-1
BUTTON KIT ASSY (S) SPRING (OPEN) KNOB ASSY (S) PANEL ASSY (S), FRONT (F7000) PANEL ASSY (S), FRONT (F7005X)
54 55
X-3385-021-1 PANEL ASSY (S), FRONT (FW700) 3-260-341-01 SHEET (FL)
not supplied
Remark
Ref. No.
Part No.
Description
56 57 58 58 58
X-3384-495-1 X-3378-390-3 A-3372-612-A A-3372-677-A A-3372-682-A
PANEL ASSY, FRONT BACK CASE ASSY (for FRONT PANEL) PANEL COMPLETE ASSY, FRONT (F7000) PANEL COMPLETE ASSY, FRONT (F7005X) PANEL COMPLETE ASSY, FRONT (FW700)
Remark
FL900 #3
1-518-953-11 INDICATOR TUBE, FLUORESCENT 7-685-105-19 SCREW +P 2X8 TYPE2 NON-SLIT
37
CDX-F7000/F7005X/FW700
4-3. CD MECHANISM SECTION (1) (MG-611XA-186//K)
not supplied
102
not supplied (SENSOR board)
101
#4
not supplied
not supplied
103
104 106
105 108 107
Ref. No. 101 102 103 104 105
38
Part No.
Description
A-3372-455-A 3-253-729-01 3-253-746-13 3-253-746-03 3-253-695-01
CHASSIS (T) SUB ASSY SPRING (LTR), TENSION COIL SPRING (DAMPER), COMPRESSION SPRING (DAMPER), COMPRESSION SPRING (KF), TENSION COIL
Remark
Ref. No. 106 107 108 #4
Part No.
Description
3-253-748-01 3-352-758-31 A-3283-350-A 7-627-552-87
DAMPER (S) SCREW (M1.7), TOOTHED LOCK SERVO BOARD, COMPLETE SCREW, PRECISION +P 1.7X2.2
Remark
CDX-F7000/F7005X/FW700
4-4. CD MECHANISM SECTION (2) (MG-611XA-186//K)
155 156
157 154 (including M901)
#5 M902 not supplied
SW4
159 not supplied
158
not supplied
153
not supplied
151
152
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Ref. No.
Part No.
Description
151 152 0 153 154 155
A-3337-637-A 3-316-938-91 8-820-207-02 A-3337-640-A A-3337-641-A
CHASSIS (OP) COMPLETE ASSY SCREW (B1.4X5), TAPPING OPTICAL PICK-UP (KSS1000E/K1RP) CHASSIS (OP) SUB ASSY (including M901) ARM SUB ASSY, CHUCKING
156
A-3337-639-A LEVER (SL) SUB ASSY
Remark
Ref. No.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
Part No.
Description
157 158 159 M902 SW4
X-3383-454-2 3-261-959-01 3-264-165-02 A-3337-638-A 1-571-099-11
LEVER (SL) ASSY SPRING (SL), TORSION SCREW MOTOR ASSY, SL (SLED) SWITCH (1 KEY) (LIMIT)
#5
7-627-850-77 SCREW, PRECISION +P 1.4X1.8
Remark
39
CDX-F7000/F7005X/FW700
4-5. CD MECHANISM SECTION (3) (MG-611XA-186//K)
203
201 202
207 211
204
209 208
210
205
207 207 M903
#4
206
Ref. No.
Part No.
Description
201 202 203 204 205
3-262-755-01 3-259-024-01 A-3337-633-A 3-259-455-02 3-253-713-01
WASHER (1.1-2.5) WHEEL (RA), WORM ARM ASSY, ROLLER SPRING (RAL) SPRING (RAR)
206 207
3-259-469-01 SPRING (LE), LEAF 2-134-636-31 SCREW (M1.7X2.5)
40
Remark
Ref. No.
Part No.
Description
208 209 210 211 M903
3-259-467-01 3-345-648-91 A-3372-456-A 3-259-468-01 A-3372-454-A
BRACKET (LEM) SCREW (M1.4), TOOTHED LOCK WORM (LEB) ASSY BEARING (LEB) MOTOR ASSY, LE (LOADING)
#4
7-627-552-87 SCREW, PRECISION +P 1.7X2.2
Remark
CDX-F7000/F7005X/FW700
4-6. CD MECHANISM SECTION (4) (MG-611XA-186//K)
254 252
255 252 256 251
253
257
Ref. No. 251 252 253 254
Part No.
Description
3-259-429-01 3-344-223-01 3-259-470-01 3-253-755-01
WHEEL (LE), WORM WASHER GEAR (LE1) LEVER (D)
Remark
Ref. No. 255 256 257
Part No.
Description
Remark
3-899-829-01 WASHER (SLIT) 3-259-032-01 GEAR (LE2) A-3372-453-A CHASSIS (M) BLOCK ASSY
41
CDX-F7000/F7005X/FW700 SECTION 5 ELECTRICAL PARTS LIST
KEY NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. • CAPACITORS uF : µF • COILS uH : µH • Abbreviation CND : Canadian model
When indicating parts by reference number, please include the board.
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
Description
Remark
< FERRITE BEAD >
KEY BOARD ********** 3-260-341-01 SHEET (FL) < CAPACITOR > C901 C903 C904 C905 C906
1-107-826-11 1-107-826-11 1-164-227-11 1-162-915-11 1-162-915-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.022uF 10PF 10PF
10% 10% 10% 0.25PF 0.25PF
16V 16V 25V 50V 50V
C907 C909 C912 C913 C915
1-107-826-11 1-107-826-11 1-216-864-11 1-107-826-11 1-164-230-11
CERAMIC CHIP CERAMIC CHIP METAL CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0 0.1uF 220PF
10% 10% 5% 10% 5%
16V 16V 1/10W 16V 50V
C916 C917 C918
1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP
0.1uF 0.1uF 0.1uF
10% 10% 10%
16V 16V 16V
< CONNECTOR > CN901
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
FB901 FB902 FB903 FB904 FB905
1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21
INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD
FB906 FB907 FB908 FB909 FB910
1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21
INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD
FB911 FB912 FB913 FB914 FB915
1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21
INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD
FB916 FB917 FB918 FB919 FB920
1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21
INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD
1-818-141-11 PLUG, CONNECTOR 20P < FLUORESCENT INDICATOR > < DIODE > FL900
D901 D902 D903 D904 D909
8-719-978-33 8-719-978-33 8-719-978-33 8-719-978-33 8-719-978-33
DIODE DIODE DIODE DIODE DIODE
DTZ-TT11-6.8B DTZ-TT11-6.8B DTZ-TT11-6.8B DTZ-TT11-6.8B DTZ-TT11-6.8B
D910 D911 D912 D913 D914
8-719-978-33 8-719-069-54 8-719-404-50 6-500-886-01 8-719-978-33
DIODE DIODE DIODE DIODE DIODE
DTZ-TT11-6.8B UDZS-TE17-5.1B MA111-TX RSA6.1ENTR DTZ-TT11-6.8B
D915 D916 D917 D918 D919
8-719-978-33 8-719-978-33 8-719-978-33 8-719-978-33 1-216-864-11
DIODE DTZ-TT11-6.8B (F7000/FW700) DIODE DTZ-TT11-6.8B (F7000/FW700) DIODE DTZ-TT11-6.8B (F7000/FW700) DIODE DTZ-TT11-6.8B (F7000/FW700) METAL CHIP 0 5% 1/10W < ROTARY ENCODER >
ENC901 1-478-474-11 ENCODER, ROTARY (VOLUME/PUSH SOUND)
42
1-518-953-11 INDICATOR TUBE, FLUORESCENT < IC >
IC901 IC902 IC903 IC904
6-803-991-01 8-759-523-94 6-600-321-01 8-759-658-25
IC IC IC IC
M30823MH-080GP TC74VHC32FT(EL) KSM-401Y (IR) PST3432UL
< COIL > L901
1-469-847-11 INDUCTOR
100uH
< DIODE > LED901 LED901 LED910 LED910 LED911
6-500-204-01 6-500-450-01 6-500-204-01 6-500-450-01 6-500-204-01
LED LED LED LED LED
CL-190UB2-X-T (IMAGE) (F7005X) CL-195SR-CD-T (IMAGE) (F7000/FW700) CL-190UB2-X-T (OFF) (F7005X) CL-195SR-CD-T (OFF) (F7000/FW700) CL-190UB2-X-T (SCRL) (F7005X)
LED911 6-500-450-01 LED CL-195SR-CD-T (SCRL) (F7000/FW700) LED912 6-500-204-01 LED CL-190UB2-X-T (EQ7) (F7005X) LED912 6-500-450-01 LED CL-195SR-CD-T (EQ7) (F7000/FW700)
CDX-F7000/F7005X/FW700 KEY Ref. No.
Part No.
Description
Remark
LED913 6-500-204-01 LED CL-190UB2-X-T (SEEK +/>/M) (F7005X) LED913 6-500-450-01 LED CL-195SR-CD-T (SEEK +/>/M) (F7000/FW700) LED914 6-500-204-01 LED CL-190UB2-X-T (DISC/PRESET +) (F7005X) LED914 6-500-450-01 LED CL-195SR-CD-T (DISC/PRESET +) (F7000/FW700) LED915 6-500-204-01 LED CL-190UB2-X-T (SEEK –/./m) (F7005X)
Ref. No.
Part No.
Description
Remark
LSW908 1-786-711-31 SWITCH, TACTILE (WITH LED) (1/REP) (F7005X) < RESISTOR > R901 R902 R903 R904 R905
1-219-286-11 1-219-286-11 1-219-286-11 1-218-847-11 1-218-851-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
680 680 680 1K 1.5K
2% 2% 2% 2% 2%
1/16W 1/16W 1/16W 1/16W 1/16W
R906 R907 R908 R909 R910
1-218-851-11 1-218-855-11 1-218-859-11 1-218-863-11 1-219-286-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
1.5K 2.2K 3.3K 4.7K 680
2% 2% 2% 2% 2%
1/16W 1/16W 1/16W 1/16W 1/16W
R911 R912 R913 R914 R915
1-219-286-11 1-219-286-11 1-218-847-11 1-218-851-11 1-218-851-11
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
680 680 1K 1.5K 1.5K
2% 2% 2% 2% 2%
1/16W 1/16W 1/16W 1/16W 1/16W
R916 R917 R918
1-218-855-11 RES-CHIP 1-218-859-11 RES-CHIP 1-216-811-11 METAL CHIP
2.2K 3.3K 150
2% 2% 5%
R918
1-216-820-11 METAL CHIP
820
R919
1-216-820-11 METAL CHIP
820
R920
1-216-811-11 METAL CHIP
150
R920
1-216-820-11 METAL CHIP
820
R921
1-216-820-11 METAL CHIP
820
R922
1-216-811-11 METAL CHIP
150
LSW901 1-771-883-31 SWITCH, TACTILE (WITH LED) (SOURCE) (F7000/FW700) LSW901 1-786-711-31 SWITCH, TACTILE (WITH LED) (SOURCE) (F7005X) LSW902 1-771-883-31 SWITCH, TACTILE (WITH LED) (DSPL) (F7000/FW700) LSW902 1-786-711-31 SWITCH, TACTILE (WITH LED) (DSPL) (F7005X) LSW903 1-771-883-31 SWITCH, TACTILE (WITH LED) (6) (F7000/FW700)
R922
1-216-820-11 METAL CHIP
820
R923
1-216-820-11 METAL CHIP
820
R924
1-216-811-11 METAL CHIP
150
R924
1-216-820-11 METAL CHIP
820
R925
1-216-820-11 METAL CHIP
820
LSW903 1-786-711-31 SWITCH, TACTILE (WITH LED) (6) (F7005X) LSW904 1-771-883-31 SWITCH, TACTILE (WITH LED) (5) (F7000/FW700) LSW904 1-786-711-31 SWITCH, TACTILE (WITH LED) (5) (F7005X) LSW905 1-771-883-31 SWITCH, TACTILE (WITH LED) (4) (F7000/FW700) LSW905 1-786-711-31 SWITCH, TACTILE (WITH LED) (4) (F7005X)
R926
1-216-811-11 METAL CHIP
150
R926
1-216-820-11 METAL CHIP
820
R927
1-216-820-11 METAL CHIP
820
R928
1-216-811-11 METAL CHIP
150
R928
1-216-820-11 METAL CHIP
820
R929
1-216-820-11 METAL CHIP
820
R930
1-216-811-11 METAL CHIP
150
R930
1-216-820-11 METAL CHIP
820
LED915 6-500-450-01 LED CL-195SR-CD-T (SEEK –/./m) (F7000/FW700) LED916 6-500-204-01 LED CL-190UB2-X-T (DISC/PRESET –) (F7005X) LED916 6-500-450-01 LED CL-195SR-CD-T (DISC/PRESET –) (F7000/FW700) LED917 6-500-204-01 LED CL-190UB2-X-T (DSO) (F7005X) LED917 6-500-450-01 LED CL-195SR-CD-T (DSO) (F7000/FW700) LED918 LED918 LED919 LED919 LED920
6-500-204-01 6-500-450-01 6-500-204-01 6-500-450-01 6-500-204-01
LED LED LED LED LED
CL-190UB2-X-T (MODE) (F7005X) CL-195SR-CD-T (MODE) (F7000/FW700) CL-190UB2-X-T (VOL1) (F7005X) CL-195SR-CD-T (VOL1) (F7000/FW700) CL-190UB2-X-T (VOL2) (F7005X)
LED920 LED921 LED921 LED922 LED922
6-500-450-01 6-500-204-01 6-500-450-01 6-500-204-01 6-500-450-01
LED LED LED LED LED
CL-195SR-CD-T (VOL2) (F7000/FW700) CL-190UB2-X-T (VOL3) (F7005X) CL-195SR-CD-T (VOL3) (F7000/FW700) CL-190UB2-X-T (VOL4) (F7005X) CL-195SR-CD-T (VOL4) (F7000/FW700)
LED923 LED923 LED924 LED924
6-500-204-01 6-500-450-01 6-500-204-01 6-500-450-01
LED LED LED LED
CL-190UB2-X-T (OPEN) (F7005X) CL-195SR-CD-T (OPEN) (F7000/FW700) CL-190UB2-X-T (SOURCE) (F7005X) CL-195SR-CD-T (SOURCE) (F7000/FW700)
< SWITCH >
LSW906 1-771-883-31 SWITCH, TACTILE (WITH LED) (3) (F7000/FW700) LSW906 1-786-711-31 SWITCH, TACTILE (WITH LED) (3) (F7005X) LSW907 1-771-883-31 SWITCH, TACTILE (WITH LED) (2/SHUF) (F7000/FW700) LSW907 1-786-711-31 SWITCH, TACTILE (WITH LED) (2/SHUF) (F7005X) LSW908 1-771-883-31 SWITCH, TACTILE (WITH LED) (1/REP) (F7000/FW700)
1/16W 1/16W 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5%
1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5%
1/10W (F7005X) 5% 1/10W (F7000/FW700)
43
CDX-F7000/F7005X/FW700 KEY Ref. No.
MAIN Part No.
Description
Remark
R931
1-216-820-11 METAL CHIP
820
R932
1-216-811-11 METAL CHIP
150
R932
1-216-820-11 METAL CHIP
820
R933
1-216-820-11 METAL CHIP
820
R934
1-216-811-11 METAL CHIP
150
R934
1-216-820-11 METAL CHIP
820
R935
1-216-820-11 METAL CHIP
820
R936
1-216-811-11 METAL CHIP
150
R936
1-216-820-11 METAL CHIP
820
R937
1-216-820-11 METAL CHIP
820
5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700)
R938
1-216-811-11 METAL CHIP
150
R938
1-216-820-11 METAL CHIP
820
R939
1-216-820-11 METAL CHIP
820
R946 R947
1-218-855-11 RES-CHIP 1-218-855-11 RES-CHIP
2.2K 2.2K
1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 2% 1/16W 2% 1/16W
R953 R954 R955 R958 R959
1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 100K 100K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R960 R961 R970 R971 R972
1-216-845-11 1-216-017-11 1-216-833-11 1-216-833-11 1-216-809-11
METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP
100K 47 10K 10K 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R973 R975 R976 R977 R978
1-216-831-11 1-216-845-11 1-216-819-11 1-216-821-11 1-218-863-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
6.8K 100K 680 1K 4.7K
5% 5% 5% 5% 2%
1/10W 1/10W 1/10W 1/10W 1/16W
R979
1-216-821-11 METAL CHIP
1K
5%
R979
1-216-823-11 METAL CHIP
1.5K
R980
1-216-821-11 METAL CHIP
1K
R980
1-216-823-11 METAL CHIP
1.5K
R981
1-216-823-11 METAL CHIP
1.5K
R982 R983
1-216-821-11 METAL CHIP 1-216-821-11 METAL CHIP
1K 1K
R983
1-216-823-11 METAL CHIP
1.5K
R984
1-216-821-11 METAL CHIP
1K
R984
1-216-823-11 METAL CHIP
1.5K
44
Ref. No.
Part No.
Description
Remark
R985
1-216-823-11 METAL CHIP
1.5K
R987
1-216-845-11 METAL CHIP
100K
5% 1/10W (F7000/FW700) 5% 1/10W
< SWITCH > S902 S903 S904 S905 S906
1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31
SWITCH, TACTILE (OFF) SWITCH, TACTILE (SEEK +/>/M) SWITCH, TACTILE (SEEK –/./m) SWITCH, TACTILE (DISC/PRESET +) SWITCH, TACTILE (DISC/PRESET –)
S907 S908 S909 S910 S912
1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31
SWITCH, TACTILE (MODE) SWITCH, TACTILE (DSO) SWITCH, TACTILE (SCRL) SWITCH, TACTILE (EQ7) SWITCH, TACTILE (IMAGE) < VIBRATOR >
X901 1-813-250-11 VIBRATOR, CRYSTAL (8MHz) *************************************************************
5%
1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700) 5% 5%
1/10W 1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7005X) 5% 1/10W (F7000/FW700)
A-3283-429-A MAIN BOARD, COMPLETE ********************* < CAPACITOR > C101 C102 C103 C106 C110
1-126-940-11 1-126-960-11 1-131-868-81 1-115-340-11 1-107-826-11
ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP
330uF 1uF 3300uF 0.22uF 0.1uF
20% 20% 20% 10% 10%
16V 50V 16V 25V 16V
C111 C142 C173 C178 C183
1-107-826-11 1-162-927-11 1-124-721-85 1-162-927-11 1-124-721-85
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT
0.1uF 100PF 10uF 100PF 10uF
10% 5% 20% 5% 20%
16V 50V 50V 50V 50V
C188 C199 C201 C202 C203
1-162-927-11 1-162-964-11 1-115-467-11 1-162-923-11 1-126-961-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
100PF 0.001uF 0.22uF 47PF 2.2uF
5% 10% 10% 5% 20%
50V 50V 10V 50V 50V
C204 C205 C206 C207 C208
1-124-695-85 1-115-340-11 1-125-891-11 1-125-891-11 1-162-927-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
22uF 0.22uF 0.47uF 0.47uF 100PF
20% 10% 10% 10% 5%
25V 25V 10V 10V 50V
C209 C210 C211 C212 C214
1-162-927-11 1-115-340-11 1-165-908-11 1-126-964-11 1-126-964-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT
100PF 0.22uF 1uF 10uF 10uF
5% 10% 10% 20% 20%
50V 25V 10V 50V 50V
C215 C216 C217 C218 C219
1-115-340-11 1-162-927-11 1-162-927-11 1-125-891-11 1-125-891-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.22uF 100PF 100PF 0.47uF 0.47uF
10% 5% 5% 10% 10%
25V 50V 50V 10V 10V
C221 C223 C225 C226 C227
1-126-964-11 1-126-964-11 1-165-908-11 1-126-964-11 1-115-340-11
ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP
10uF 10uF 1uF 10uF 0.22uF
20% 20% 10% 20% 10%
50V 50V 10V 50V 25V
CDX-F7000/F7005X/FW700 MAIN Ref. No.
Part No.
Description
Part No.
Description
C242 C273 C278 C283 C288
1-162-927-11 1-124-721-85 1-162-927-11 1-124-721-85 1-162-927-11
CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP
100PF 10uF 100PF 10uF 100PF
5% 20% 5% 20% 5%
50V 50V 50V 50V 50V
Remark
C508 C509 C510 C511 C620
1-125-837-11 1-125-837-11 1-135-834-11 1-162-970-11 1-104-665-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
1uF 1uF 2.2uF 0.01uF 100uF
10% 20%
6.3V 6.3V 6.3V 25V 10V
C303 C304 C306 C307 C308
1-126-933-11 1-107-826-11 1-126-933-11 1-107-826-11 1-124-717-85
ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT
100uF 0.1uF 100uF 0.1uF 1uF
20% 10% 20% 10% 20%
16V 16V 16V 16V 50V
C621 C622 C623 C624 C625
1-128-552-11 1-126-934-11 1-126-964-11 1-164-315-11 1-162-966-11
ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP
47uF 220uF 10uF 470PF 0.0022uF
20% 20% 20% 5% 10%
63V 16V 50V 50V 50V
C309 C311 C312 C313 C315
1-124-717-85 1-125-710-11 1-126-933-11 1-164-156-11 1-162-919-11
ELECT DOUBLE LAYERS ELECT CERAMIC CHIP CERAMIC CHIP
1uF 0.1F 100uF 0.1uF 22PF
20%
5%
50V 5.5V 16V 25V 50V
C626 C627 C628 C629 C901
1-107-826-11 1-162-923-11 1-107-826-11 1-126-933-11 1-126-965-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT
0.1uF 47PF 0.1uF 100uF 22uF
10% 5% 10% 20% 20%
16V 50V 16V 16V 50V
C316 C317 C318 C319 C320
1-162-918-11 1-162-970-11 1-165-176-11 1-162-970-11 1-126-961-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
18PF 0.01uF 0.047uF 0.01uF 2.2uF
5% 10% 10% 10% 20%
50V 25V 16V 25V 50V
C903 C928 C930
1-126-963-11 ELECT 1-164-156-11 CERAMIC CHIP 1-126-965-11 ELECT
4.7uF 0.1uF 22uF
20%
50V 25V 50V
C321 C322 C323 C330 C332
1-126-964-11 1-162-975-11 1-162-975-11 1-162-964-11 1-164-156-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
10uF 24PF 24PF 0.001uF 0.1uF
20% 5% 5% 10%
50V 50V 50V 50V 25V
* CN401 CN601 CN602 CN603 CNP101
C333 C334 C335 C336 C341
1-126-933-11 1-107-826-11 1-126-933-11 1-107-826-11 1-162-966-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP
100uF 0.1uF 100uF 0.1uF 0.0022uF
20% 10% 20% 10% 10%
16V 16V 16V 16V 50V
C342 C401 C403 C416 C417
1-162-966-11 1-126-947-11 1-125-891-11 1-125-837-11 1-125-837-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0022uF 47uF 0.47uF 1uF 1uF
10% 20% 10% 10% 10%
50V 16V 10V 6.3V 6.3V
C418 C419 C420 C421 C422
1-124-721-85 1-126-959-11 1-126-959-11 1-125-837-11 1-124-673-85
ELECT ELECT ELECT CERAMIC CHIP ELECT
10uF 0.47uF 0.47uF 1uF 100uF
20% 20% 20% 10% 20%
50V 50V 50V 6.3V 10V
C423 C424 C425 C426 C427
1-162-970-11 1-162-965-11 1-136-154-00 1-162-927-11 1-162-927-11
CERAMIC CHIP CERAMIC CHIP FILM CERAMIC CHIP CERAMIC CHIP
0.01uF 0.0015uF 0.012uF 100PF 100PF
10% 10% 5% 5% 5%
25V 50V 50V 50V 50V
C428 C429 C430 C431 C432
1-162-927-11 1-162-927-11 1-162-965-11 1-162-927-11 1-136-154-00
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP FILM
100PF 100PF 0.0015uF 100PF 0.012uF
5% 5% 10% 5% 5%
50V 50V 50V 50V 50V
C433 C434 C435 C442 C443
1-126-960-11 1-126-960-11 1-126-960-11 1-162-927-11 1-126-964-11
ELECT ELECT ELECT CERAMIC CHIP ELECT
1uF 1uF 1uF 100PF 10uF
20% 20% 20% 5% 20%
50V 50V 50V 50V 50V
C501 C502 C507
1-162-970-11 CERAMIC CHIP 1-126-964-11 ELECT 1-126-933-11 ELECT
0.01uF 10uF 100uF
10% 20% 20%
25V 50V 16V
20%
Ref. No.
Remark 10% 10%
20%
< CONNECTOR > 1-506-985-11 1-569-915-11 1-779-056-21 1-779-056-21 1-774-701-21
PIN, CONNECTOR (PC BOARD) 3P SOCKET, CONNECTOR 22P PIN, CONNECTOR (PC BOARD) 5P PIN, CONNECTOR (PC BOARD) 5P PIN, CONNECTOR 16P
CNP102 1-580-907-41 PLUG, CONNECTOR (BUS CONTROL IN) CNP301 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P < JACK > CNJ101 1-764-270-21 JACK, STEREO MINIATURE (DIA.3.5) (REMOTE IN) < DIODE > D101 D102 D103 D104 D105
8-719-083-66 8-719-083-66 6-500-540-01 8-719-069-56 8-719-083-66
DIODE DIODE DIODE DIODE DIODE
UDZS-TE17-18B UDZS-TE17-18B RB521S-30FTE61 UDZS-TE17-6.2B UDZS-TE17-18B
D106 D108 D109 D110 D111
8-719-978-33 8-719-083-66 8-719-200-82 8-719-053-18 8-719-053-18
DIODE DIODE DIODE DIODE DIODE
DTZ-TT11-6.8B UDZS-TE17-18B 11ES2 1SR154-400TE-25 1SR154-400TE-25
D112 D113 D114 D115 D116
8-719-053-18 8-719-053-18 8-719-053-18 8-719-053-18 8-719-053-18
DIODE DIODE DIODE DIODE DIODE
1SR154-400TE-25 1SR154-400TE-25 1SR154-400TE-25 1SR154-400TE-25 1SR154-400TE-25
D117 D118 D119 D120 D121
8-719-053-18 6-500-508-01 6-500-508-01 6-500-508-01 6-500-508-01
DIODE DIODE DIODE DIODE DIODE
1SR154-400TE-25 RR263M-400FTR RR263M-400FTR RR263M-400FTR RR263M-400FTR
D122 D123 D305 D306 D401
8-719-978-33 8-719-200-82 8-719-988-61 8-719-988-61 8-719-404-50
DIODE DIODE DIODE DIODE DIODE
DTZ-TT11-6.8B 11ES2 1SS355TE-17 1SS355TE-17 MA111-TX
45
CDX-F7000/F7005X/FW700 MAIN Ref. No.
Part No.
Description
D403 D501 D601 D602 D603
8-719-069-55 8-719-069-55 8-719-978-33 8-719-978-33 8-719-978-33
DIODE DIODE DIODE DIODE DIODE
UDZS-TE17-5.6B UDZS-TE17-5.6B DTZ-TT11-6.8B DTZ-TT11-6.8B DTZ-TT11-6.8B
Remark
Ref. No.
D604 D605 D606 D620 D621
8-719-978-33 6-500-886-01 6-500-886-01 8-719-053-18 8-719-053-18
DIODE DIODE DIODE DIODE DIODE
DTZ-TT11-6.8B RSA6.1ENTR RSA6.1ENTR 1SR154-400TE-25 1SR154-400TE-25
D622 D623 D624 D625 D626
8-719-055-33 8-719-055-30 8-719-055-30 8-719-083-66 8-719-069-54
DIODE DIODE DIODE DIODE DIODE
D1FL40 D1FS4A-TA D1FS4A-TA UDZS-TE17-18B UDZS-TE17-5.1B
Q101 Q102 Q103 Q171 Q181
8-729-055-94 8-729-120-28 8-729-120-28 6-550-752-01 6-550-752-01
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
D627 D907 D909 D910 D911
6-500-540-01 8-719-988-61 8-719-988-61 8-719-069-55 8-719-420-51
DIODE DIODE DIODE DIODE DIODE
RB521S-30FTE61 1SS355TE-17 1SS355TE-17 UDZS-TE17-5.6B MA729
Q271 Q281 Q401 Q402 Q408
6-550-752-01 6-550-752-01 8-729-055-95 8-729-055-91 8-729-053-84
TRANSISTOR DTC614TKT146 TRANSISTOR DTC614TKT146 TRANSISTOR SRC1204SF TRANSISTOR SRA2202SF FET SSM3KO9FU(T5LSONY1)
Q470 Q501 Q601 Q602 Q620
6-550-752-01 8-729-920-85 8-729-055-91 8-729-055-95 8-729-048-72
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR FET 2SK2615
Q621 Q622 Q623 Q624 Q907
8-729-055-91 8-729-055-95 8-729-055-95 6-550-828-01 8-729-120-28
TRANSISTOR SRA2202SF TRANSISTOR SRC1204SF TRANSISTOR SRC1204SF FET RSQ035P03TR TRANSISTOR 2SC1623-L5L6
Q914 Q915 Q916
8-729-055-91 TRANSISTOR SRA2202SF 8-729-015-11 TRANSISTOR 2SD1802FAST-TL 8-729-055-94 TRANSISTOR SRC1202SF
L502 L503 L620 L901
Part No.
Description
1-414-394-41 1-414-394-41 1-456-729-11 1-414-394-41
INDUCTOR INDUCTOR COIL, POWER INDUCTOR
Remark 2.2uH 2.2uH 2.2uH
< JACK > PJ401
< TRANSISTOR >
< EMI FILTER > FB325 FB326 FB327 FB328
1-414-813-11 1-414-813-11 1-414-813-11 1-414-813-11
FILTER, EMI (SMD) FILTER, EMI (SMD) FILTER, EMI (SMD) FILTER, EMI (SMD) < JUMPER RESISTOR >
FB329 FB330
1-216-295-11 SHORT CHIP 1-216-295-11 SHORT CHIP
0 0
< FERRITE BEAD > FB441 FB442
1-774-700-11 JACK, PIN 6P (BUS AUDIO IN/AUX IN, AUDIO OUT REAR/FRONT)
1-414-813-11 FERRITE, EMI (SMD) 1-414-813-11 FERRITE, EMI (SMD)
SRC1202SF 2SC1623-L5L6 2SC1623-L5L6 DTC614TKT146 DTC614TKT146
DTC614TKT146 2SD1664-QR SRA2202SF SRC1204SF
< RESISTOR > < IC > IC110 IC201 IC251 IC302 IC303
8-759-096-16 6-705-359-01 8-759-679-05 8-759-658-25 6-803-989-01
IC IC IC IC IC
MM1175XFF TDA8588AJ/N2 TC7WH34FU(TE12R) PST3432UL M30624MGP-122GP
IC401 IC620
6-703-303-01 IC TDA7416 6-705-542-01 IC NJM2377M(TE2) < JACK >
J601
1-793-598-11 JACK (ANTENNA) < JUMPER RESISTOR >
JR302
1-216-864-11 METAL CHIP
0
< COIL > L101 L301 L302 L303 L320
1-456-617-11 1-414-394-41 1-414-394-41 1-414-394-41 1-414-394-41
L401
1-414-394-41 INDUCTOR
46
COIL, CHOKE INDUCTOR INDUCTOR INDUCTOR INDUCTOR
250uH 2.2uH 2.2uH 2.2uH 2.2uH 2.2uH
5%
1/10W
R101 R102 R103 R104 R105
1-216-077-11 1-216-049-11 1-216-821-11 1-216-829-11 1-216-841-11
RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP
15K 1K 1K 4.7K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R106 R107 R108 R109 R110
1-216-841-11 1-216-073-00 1-216-073-00 1-216-833-11 1-216-833-11
METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP
47K 10K 10K 10K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R111 R112 R113 R114 R115
1-216-841-11 1-216-821-11 1-216-864-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 1K 0 100 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R116 R117 R119 R142 R143
1-216-809-11 1-216-797-11 1-216-864-11 1-216-825-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 10 0 2.2K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R172 R174 R175
1-216-295-11 SHORT CHIP 1-216-809-11 METAL CHIP 1-216-841-11 METAL CHIP
0 100 47K
5% 5%
1/10W 1/10W
CDX-F7000/F7005X/FW700 MAIN Ref. No.
Part No.
Description
R182 R184 R185 R201 R202
1-216-295-11 1-216-809-11 1-216-841-11 1-216-841-11 1-216-809-11
SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 100 47K 47K 100
Remark 5% 5% 5% 5%
R203 R204 R205 R206 R240
1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-025-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
1K 1K 1K 1K 100
R241 R242 R243 R250 R251
1-216-025-11 1-216-825-11 1-216-833-11 1-216-864-11 1-216-864-11
RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
R252 R253 R254 R255 R256
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
R257 R258 R259 R260 R261
Ref. No.
Part No.
Description
1/10W 1/10W 1/10W 1/10W
R356 R357 R360 R363 R364
1-218-871-11 1-218-871-11 1-216-845-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 10K 100K 100K 100K
0.5% 0.5% 5% 5% 5%
Remark 1/10W 1/10W 1/10W 1/10W 1/10W
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R365 R366 R367 R368 R370
1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 100K 100K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
100 2.2K 10K 0 0
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R377 R381 R391 R393 R401
1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-017-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
100K 100K 100K 100K 47
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 0 0 0
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R402 R403 R407 R408 R410
1-216-864-11 1-216-295-11 1-216-841-11 1-216-809-11 1-216-295-11
METAL CHIP SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP
0 0 47K 100 0
5%
1/10W
5% 5%
1/10W 1/10W
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 0 0 0
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R414 R415 R416 R417 R418
1-216-833-11 1-216-833-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 10K 100 100 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R262 R263 R264 R265 R272
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-295-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP
0 0 0 0 0
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
R419 R420 R421 R422 R424
1-216-809-11 1-216-833-11 1-216-833-11 1-216-813-11 1-216-825-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 10K 10K 220 2.2K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R274 R275 R282 R284 R285
1-216-809-11 1-216-841-11 1-216-295-11 1-216-809-11 1-216-841-11
METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP
100 47K 0 100 47K
5% 5%
1/10W 1/10W
METAL CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
1/10W
1/10W 1/10W
1-216-864-11 1-216-295-11 1-216-295-11 1-216-295-11 1-216-295-11
5%
5% 5%
R426 R429 R431 R433 R435
R300 R301 R302 R304 R311
1-216-864-11 1-216-864-11 1-216-845-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 100K 100K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R443 R444 R445 R446 R478
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 0 0 0
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R312 R314 R319 R322 R323
1-216-845-11 1-216-845-11 1-216-821-11 1-216-827-11 1-216-827-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 1K 3.3K 3.3K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R501 R502 R504 R600 R601
1-216-821-11 1-216-864-11 1-216-864-11 1-216-295-11 1-216-029-00
METAL CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP
1K 0 0 0 150
5% 5% 5%
1/10W 1/10W 1/10W
5%
1/10W
R326 R330 R332 R333 R335
1-216-853-11 1-216-845-11 1-218-871-11 1-216-809-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470K 100K 10K 100 22K
5% 5% 0.5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R602 R603 R620 R621 R622
1-216-029-00 1-216-029-00 1-216-230-00 1-216-230-00 1-218-863-11
METAL CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP
150 150 22K 22K 4.7K
5% 5% 5% 5% 0.5%
1/10W 1/10W 1/8W 1/8W 1/10W
R341 R342 R343 R344 R345
1-216-845-11 1-216-845-11 1-216-845-11 1-216-833-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 100K 10K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R623 R624 R625 R626 R627
1-218-895-11 1-218-847-11 1-216-809-11 1-216-848-11 1-216-846-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 1K 100 180K 120K
0.5% 0.5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R346 R350 R351
1-216-833-11 METAL CHIP 1-216-809-11 METAL CHIP 1-216-809-11 METAL CHIP
10K 100 100
5% 5% 5%
1/10W 1/10W 1/10W
R628 R629 R630
1-216-841-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-837-11 METAL CHIP
47K 10K 22K
5% 5% 5%
1/10W 1/10W 1/10W
47
CDX-F7000/F7005X/FW700 MAIN Ref. No.
SENSOR
SERVO
Part No.
Description
Remark
Ref. No.
Part No.
Description
R631 R632 R633 R634 R635
1-216-833-11 1-216-841-11 1-216-809-11 1-216-833-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 47K 100 10K 0
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
C18 C19 C20 C21 C23
1-162-970-11 1-107-826-11 1-107-826-11 1-162-970-11 1-162-923-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.1uF 0.1uF 0.01uF 47PF
10% 10% 10% 10% 5%
25V 16V 16V 25V 50V
R636 R642 R643 R904 R910
1-216-839-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-845-11
METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP
33K 0 0 0 100K
5%
1/10W
5% 5%
1/10W 1/10W
C25 C26 C27 C28 C29
1-162-908-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
3PF 0.1uF 0.1uF 0.1uF 0.1uF
0.25PF 10% 10% 10% 10%
50V 16V 16V 16V 16V
R920 R921 R922 R929 R949
1-216-073-00 1-216-073-00 1-216-845-11 1-216-837-11 1-216-057-00
RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP
10K 10K 100K 22K 2.2K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
C30 C31 C32 C34 C35
1-162-921-11 1-162-925-11 1-107-826-11 1-107-826-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
33PF 68PF 0.1uF 0.1uF 0.01uF
5% 5% 10% 10% 10%
50V 50V 16V 16V 25V
R950
1-216-057-00 METAL CHIP
2.2K
5%
1/10W
C36 C37 C38 C39 C70
1-162-967-11 1-162-970-11 1-104-609-11 1-107-826-11 1-162-965-11
CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP
0.0033uF 0.01uF 100uF 0.1uF 0.0015uF
10% 10% 20% 10% 10%
50V 25V 4V 16V 50V
C71 C72 C73 C74 C75
1-162-965-11 1-162-962-11 1-162-962-11 1-107-826-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0015uF 470PF 470PF 0.1uF 0.1uF
10% 10% 10% 10% 10%
50V 50V 50V 16V 16V
C76 C77 C78 C79
1-162-970-11 1-162-970-11 1-164-227-11 1-164-227-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.01uF 0.022uF 0.022uF
10% 10% 10% 10%
25V 25V 25V 25V
< SWITCH > S300 S301
1-786-458-11 SWITCH, PUSH (1 KEY) (NOSE DET) 1-762-638-21 SWITCH, TACTILE (RESET) < TRANSFORMER >
T620
1-443-212-11 TRANSFORMER, DC-DC CONVERTER
Remark
< THERMISTOR (POSITIVE) > TH100
1-801-792-21 THERMISTOR, POSITIVE < TUNER >
TUX501 A-3220-959-A TUNER UNIT (TUX-032)
< CONNECTOR >
< VIBRATOR >
CN1 CN2
1-817-275-21 CONNECTOR, BOARD TO BOARD 28P 1-794-153-21 CONNECTOR, FPC (ZIF) 16P
X301 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz) X302 1-813-254-11 VIBRATOR, CRYSTAL (6MHz) *************************************************************
< FERRITE BEAD > FB1
1-414-760-21 INDUCTOR, FERRITE BEAD
SENSOR BOARD *************
< IC >
< SWITCH >
IC1 IC2
6-703-699-01 IC uPD63712GC-8EU-A 6-705-002-01 IC BA5966FP-FE2
SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF) SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN) *************************************************************
< FERRITE BEAD > JR40 JR41 JR90 JR91
A-3283-350-A SERVO BOARD, COMPLETE **********************
1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21
INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD
< CAPACITOR > < TRANSISTOR > C1 C2 C3 C5 C6
1-107-826-11 1-162-970-11 1-107-826-11 1-107-826-11 1-100-381-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP
0.1uF 0.01uF 0.1uF 0.1uF 10uF
10% 10% 10% 10% 20%
16V 25V 16V 16V 16V
C7 C8 C11 C13 C17
1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
10% 10% 10% 10% 10%
16V 16V 16V 16V 16V
48
Q1
8-729-904-87 TRANSISTOR 2SB1197K-R < RESISTOR >
R1 R6 R7 R9 R11
1-216-841-11 1-216-833-11 1-216-840-11 1-216-822-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
R12
1-216-809-11 METAL CHIP
47K 10K 39K 1.2K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
100
5%
1/10W
CDX-F7000/F7005X/FW700 SERVO Ref. No.
Part No.
Description
R13 R14 R15 R41 R42
1-216-833-11 1-216-797-11 1-216-797-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
R44 R45 R70 R71 R72
1-414-760-21 1-414-760-21 1-216-842-11 1-216-833-11 1-216-842-11
R73 R74 R75 R76 R77
Remark 10K 10 10 1K 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD METAL CHIP 56K METAL CHIP 10K METAL CHIP 56K
5% 5% 5%
1/10W 1/10W 1/10W
1-216-833-11 1-216-837-11 1-216-833-11 1-216-837-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 22K 10K 22K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R78 R79 R80 R81 R82
1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 10K 10K 10K 22K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R83 R84 R85
1-216-833-11 METAL CHIP 1-216-837-11 METAL CHIP 1-216-833-11 METAL CHIP
10K 22K 10K
5% 5% 5%
1/10W 1/10W 1/10W
< SWITCH > SW1
1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)
Ref. No.
Part No.
Description
SUB Remark
MISCELLANEOUS *************** 10 12 0 153 154 F901
1-776-207-72 1-790-375-12 8-820-207-02 A-3337-640-A 1-532-877-11
CORD (WITH CONNECTOR) (POWER) CORD (WITH CONNECTOR) (SUB OUT (MONO)) OPTICAL PICK-UP (KSS1000E/K1RP) CHASSIS (OP) SUB ASSY (including M901) FUSE (BLADE TYPE) (AUTO FUSE) 10A
M902 A-3337-638-A MOTOR ASSY, SL (SLED) M903 A-3372-454-A MOTOR ASSY, LE (LOADING) SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT) ************************************************************* ACCESSORIES ************ 1-477-110-41 REMOTE COMMANDER (RM-X118A) 3-230-047-01 LID, BATTERY CASE (for RM-X118A) 3-263-380-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH) (F7000/F7005X) 3-263-380-21 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (FW700) 3-263-410-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, FRENCH) (F7000/F7005X) 3-263-410-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH) (FW700) 7-685-234-19 SCREW +KTP 2.6X8 TYPE2 NON-SLIT (F7000/FW700) X-3378-390-3 CASE ASSY (for FRONT PANEL) *************************************************************
< VIBRATOR > PARTS FOR INSTALLATION AND CONNECTIONS ***************************************
X1 1-795-562-21 VIBRATOR, CERAMIC (16.9344MHz) ************************************************************* 301 302 303 304 305
SUB BOARD ********** 1-828-511-11 CABLE, FLAT (FFC) 22P < CONNECTOR >
301
X-3382-647-1 3-934-325-01 3-264-055-01 1-776-207-72 3-246-471-01
FRAME ASSY, FITTING SCREW (+K 5X8 TP) COLLAR CORD (WITH CONNECTOR) (POWER) KEY (FRAME)
302
303
CNP501 1-818-142-11 SOCKET, CONNECTOR 20P < DIODE > ×4
D990 D991 LED931 LED931
8-719-978-33 8-719-978-33 6-500-895-01 8-719-082-38
DIODE DTZ-TT11-6.8B (F7005X) DIODE DTZ-TT11-6.8B (F7005X) LED CL-270UB2-X-TS (WINDOW) (F7005X) LED CL-270SR-C-TS (WINDOW) (F7000/FW700) LED932 6-500-204-01 LED CL-190UB2-X-T (Z) (F7005X)
304
305 ×2
LED932 6-500-450-01 LED CL-195SR-CD-T (Z) (F7000/FW700) < RESISTOR > R990
1-216-809-11 METAL CHIP
100
R990
1-216-817-11 METAL CHIP
470
R991
1-216-817-11 METAL CHIP
470
5%
1/10W (F7005X) 5% 1/10W (F7000/FW700) 5% 1/10W (F7000/FW700)
< SWITCH > S901 1-771-884-31 SWITCH, TACTILE (Z) ************************************************************* The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
49
CDX-F7000/F7005X/FW700
REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. 1.0
50
Date 2003. 12
Description of Revision New
