Transcript
http://www.xiaoyu163.com
CDX-GT51W/GT510/ GT560/GT560S
376315150 892498299 QQSERVICE MANUAL
US Model Canadian Model
Ver. 1.2 2007.04
CDX-GT51W/GT510
E Model CDX-GT560/GT560S
TEL
TEL NEW
AUDIO POWER SPECIFICATIONS (US, CND MODEL) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion.
CD Drive Mechanism Type
MG-101FA-188//Q
Optical Pick-up Name
DAX-25A
CD player section Signal-to-noise ratio Frequency response Wow and flutter
SPECIFICATIONS
AM Tuning range
120 dB 10 – 20,000 Hz Below measurable limit
Tuner section FM Tuning range
87.5 – 107.9 MHz (US, CND model) 87.5 – 108.0 MHz (EA model) 87.5 – 108.0 MHz (at 50 kHz step) (E, MX model) 87.5 – 107.9 MHz (at 200 kHz step) (E, MX model) FM tuning interval 50 kHz/200 kHz switchable (E, MX model) Antenna (aerial) terminal External antenna (aerial) connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz
www 9-887-402-03 2007D04-1 © 2007.04
530 – 1,710 kHz (US, CND model) 531 – 1,602 kHz (EA model) 531 – 1,602 kHz (at 9 kHz step) (E, MX model) 530 – 1,710 kHz (at 10 kHz step) (E, MX model) AM tuning interval 9 kHz/10 kHz switchable (E, MX model) Antenna (aerial) terminal External antenna (aerial) connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms) General Outputs
Audio outputs terminal (front, sub/rear switchable) Power antenna (aerial) relay control terminal Power amplifier control terminal – Continued on next page –
x aoy u163. com
FM/AM COMPACT DISC PLAYER
.Sony Corporation i
eVehicle Division Published by Sony Techno Create Corporation
http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
TEL 13942296513
QQ
QQ
Model Name Using Similar Mechanism
13942296513
13942296513
• The tuner and CD sections have no adjustments.
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299
Inputs
Tone controls
Power requirements Dimensions Mounting dimensions Mass Supplied accessories
Telephone ATT control terminal Illumination control terminal BUS control input terminal BUS audio input terminal Remote controller input terminal Antenna (aerial) input terminal AUX input jack (stereo mini jack) Low: ±10 dB at 60 Hz (XPLOD) Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz (XPLOD) 12 V DC car battery (negative ground (earth)) Approx. 178 × 50 × 180 mm (7 1/8 × 2 × 7 1/8 in.) (w/h/d) Approx. 182 × 53 × 162 mm (7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d) Approx. 1.2 kg (2 lb. 11 oz.) Card remote commander: RM-X151 Parts for installation and connections (1 set)
TEST DISCS Please use the following test discs for the check on the CD section. YDES-18 (Part No. 3-702-101-01) PATD-012 (Part No. 4-225-203-01)
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
US and foreign patents licensed from Dolby Laboratories. • Abbreviation CND : Canadian model EA : Saudi Arabia model MX : Mexican model
optical pick-up
SERVICE NOTES
NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
QQ 376315150 892498299
semi-fixed resistor
• CDX-GT560/GT560S
This label is located on the bottom of the chassis.
www
xiaoy u163. com
SAFETY-RELATED COMPONENT WARNING!!
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
.
2 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
QQ
QQ
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care.
13942296513
13942296513
If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pickup block.
TEL
TEL
Design and specifications are subject to change without notice.
Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat.
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 • CD Playback You can play CD-DA (also containing CD TEXT*) and CD-R/ CD-RW (MP3/WMA/AAC files also containing Multi Session) and ATRAC CD (ATRAC3 and ATRAC3plus format). Type of discs
SOLDER • UNLEADED Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
Label on the disc
: LEAD FREE MARK CD-DA
QQ
QQ
QQ 376315150 892498299
EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below.
376315150 892498299
376315150 892498299
TEL 13942296513
• Connect the MAIN board (CNP301) and the SERVO board (CN2) with the extension cable (Part No. J-2502-076-1).
MAIN BOARD CN350
www
J-2502-076-1
xiaoy u163. com
SERVO BOARD CN2
.
3 http://www.xiaoyu163.com
13942296513
13942296513
* A CD TEXT disc is a CD-DA that includes information such as disc, artist and track name.
TEL
TEL
MP3 WMA AAC ATRAC CD
Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S Ver. 1.2
QQ 376315150 892498299
NOTE FOR REPLACEMENT OF THE SERVO BOARD When repairing, the complete SERVO board (A-1177-362-A) should be replaced since any parts in the SERVO board cannot be repaired.
TABLE OF CONTENTS
1.
Location of Controls (CDX-GT51W: US) ...................... Connections (CDX-GT51W: US) ................................... Location of Controls (CDX-GT51W: CND/GT510) ...... Connections (CDX-GT51W: CND/GT510) .................... Location of Controls (CDX-GT560: E, MX/GT560S) ... Connections (CDX-GT560: E, MX/GT560S) .................
NOTE FOR REPLACEMENT OF THE AUX JACK (J901) To replace the AUX jack requires alignment. 1. Insert the AUX jack into the KEY board. 2. Place the KEY board on the front panel. 3. Solder the three terminals of the jack.
KEY board
Sub Panel Assy ................................................................ CD Mechanism Block ..................................................... Main Board ...................................................................... Servo Board ..................................................................... Chassis (T) Sub Assy ....................................................... Roller Arm Assy .............................................................. Chassis (OP) Assy ...........................................................
3.
DIAGNOSIS FUNCTION ........................................ 16
4.
DIAGRAMS
4-1. 4-2. 4-3. 4-4. 4-5. 4-6. 4-7. 4-8. 4-9. 4-10.
Block Diagram –Main Section– ...................................... Block Diagram –Display Section– .................................. Printed Wiring Board –Main Section– ............................ Schematic Diagram –Main Section (1/3)– ...................... Schematic Diagram –Main Section (2/3)– ...................... Schematic Diagram –Main Section (3/3)– ...................... Printed Wiring Board –Sub Section– .............................. Schematic Diagram –Sub Section– ................................. Printed Wiring Board –Key Section– .............................. Schematic Diagram –Key Section– .................................
5.
EXPLODED VIEWS
12 12 13 13 14 14 15
19 20 21 22 23 24 25 26 27 28
QQ 376315150 892498299 5-1. Main Section .................................................................... 33 5-2. Front Panel Section ......................................................... 34 5-3. CD Mechanism Section (MG-101FA-188//Q) ................ 35
6.
www
.
ELECTRICAL PARTS LIST .................................. 36
xiaoy u163. com
4 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
DISASSEMBLY
2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7.
QQ
QQ
front panel
2.
13942296513
13942296513
TEL 13942296513
5 5 7 7 9 9
TEL
TEL AUX jack
GENERAL
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S SECTION 1 This section is extracted GENERAL
QQ 376315150 892498299 from instruction manual.
• LOCATION OF CONTROLS (CDX-GT51W: US) Location of controls and basic operations Main unit
12 3
4
OFF
67
5
OPEN
PUSH SELECT
DSO
H EQ3 (equalizer) button 9 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).
The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4).
I Receptor for the card remote commander
ql < (.)/, (>) buttons To control CD/radio, the same as (SEEK) –/+ on the unit.
SOURCE
SEEK
AUX
SEEK
EQ3
J SEEK –/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold).
MODE CAT BTM
GP/ALBM
DSPL
1
2
REP
SHUF
3
4
PAUSE
5
6
SCRL
CDX-GT51W
8 9 q; qa qs qd
qf
qg
Front panel removed
qh
qj
K BTM/CAT*2 button 8 To start the BTM function (press and hold).
qk
L MODE button 8, 11 To select the radio band (FM/AM); select the SAT tuner band (mode)*2; select the unit*3. M DSPL (display) button 8 To change display items.
1 4 ql
OFF
SOURCE
wa ws qs
ATT
SEL
MODE
+
wd –
qd
1 4
qg
SCRL
DSPL 2
3
5
6
wf
A OFF button To power off; stop the source.
O SCRL (scroll) button 8 To scroll the display item.
B DSO button 4 To select the DSO mode (1, 2, 3 or OFF). The larger the number, the more enhanced the effect.
wd M (+)/m (–) buttons To control CD, the same as (1)/(2) (GP/ALBM –/+) on the unit. wf Number buttons To receive stored stations (press); store stations (press and hold). When an MD changer is connected. When the SAT tuner is connected. When a CD/MD changer is connected. When an ATRAC CD is played. When an MP3/WMA/AAC is played. If the changer is connected, the operation is different, see page 11. *7 When playing back on this unit. *1 *2 *3 *4 *5 *6
Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip For details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 14.
P RESET button 4
C Volume control dial/select button 9 To adjust volume (rotate); select setup items (press and rotate). D SOURCE button To power on; change the source (Radio/CD/ MD*1/AUX/SAT*2).
Q Z (eject) button 5 To eject the disc. R Disc slot 5 To insert the disc.
E Display window
+
w;
Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.
ws SEL (select) button The same as the select button on the unit.
13942296513
13942296513
Card remote commander RM-X151
wa ATT (attenuate) button To attenuate the sound. To cancel, press again.
TEL
TEL
RESET
N Number buttons CD/MD*1: (1)/(2): GP*4/ALBM*5 –/+ To skip albums (press); skip albums continuously (press and hold).*6 (3): REP 8, 11 (4): SHUF 8, 11 (6): PAUSE*7 To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold).
w; VOL (volume) +/– button To adjust volume.
VOL
F AUX input jack 10 To connect a portable audio device.
QQ 376315150 892498299
7
376315150 892498299
376315150 892498299
TEL 13942296513
G OPEN button 5
6
QQ
QQ
–
• CONNECTIONS (CDX-GT51W: US)
Connection example Notes (B-A) • Be sure to connect the ground (earth) lead before connecting the amplifier. • The alarm will only sound if the built-in amplifier is used.
A
Tip (B-B- ) For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary.
AUDIO OUT REAR*
Ejemplo de conexiones Notas (B-A) • Asegúrese de conectar primero el cable de conexión a masa antes de realizar la conexión del amplificador. • La alarma sonará únicamente si se utiliza el amplificador incorporado.
* AUDIO OUT SUB/REAR
B
Sugerencia (B-B- ) Si desea conectar dos o más cambiadores de CD/MD, necesitará el selector de fuente XA-C40 (no suministrado).
BUS AUDIO IN
BUS CONTROL IN
www
xiaoy u163. com
BUS AUDIO IN
Source selector* Selector de fuente* XA-C40
.
BUS CONTROL IN
* not supplied no suministrado
5 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 *1
Source selector (not supplied) Selector de fuente (no suministrado)
Supplied with the CD/MD changer Suministrado con el cambiador de CD/MD
XA-C40
Supplied with XA-C40 Suministrado con el XA-C40
*1 AUDIO OUT FRONT
REMOTE IN
*3 BUS AUDIO IN
L R
from car antenna (aerial) desde la antena del automóvil
BUS AUDIO AUDIO OUT IN REAR
AUDIO OUT REAR*2
AUDIO OUT FRONT
*1 RCA pin cord (not supplied) *2 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. *3 Insert with the cord upwards.
2 Black Negro
White Blanco
1
Blue Azul
Left Izquierdo
ANT REM
2
White/black striped Con rayas blancas y negras Gray Gris
Max. supply current 0.1 A Corriente máx. de alimentación de 0,1 A Light blue Azul celeste
ATT
Right Derecho Gray/black striped Con rayas grises y negras
Orange/white striped Con rayas naranjas y blancas
ANT REM
Green Verde Left Izquierdo
Purple Morado
Yellow Amarillo
Right Derecho
Purple/black striped Con rayas moradas y negras
Connection diagram 1 To a metal surface of the car First connect the black ground (earth) lead, then connect the yellow and red power supply leads.
2 To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster Notes • It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). • When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.”
3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit.
4 To the interface cable of a car telephone 5 To a car’s illumination signal Be sure to connect the black ground (earth) lead to a metal surface of the car first.
6 To the +12 V power terminal which is energized in the accessory position of the ignition switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. • When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.”
7 To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first.
Notes on the control and power supply leads • The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna (aerial) in the rear/ side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. • A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly.
5 6
QQ
376315150 892498299
Diagrama de conexión 1 A una superficie metálica del automóvil Conecte primero el cable de conexión a masa negro, y después los cables amarillo, y rojo de fuente de alimentación.
2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de señal de la antena Notas • Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.
3 A AMP REMOTE IN de un amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad.
4 Al cable de interfaz de un teléfono para automóvil 5 A una señal de iluminación del automóvil Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil.
6 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de encendido Notas • Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.
7
Notas sobre los cables de control y de fuente de alimentación • El cable de control de la antena motorizada (azul) suministrará cc de + 12 V cuando conecte la alimentación del sintonizador. • Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de fuente de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener más información, consulte a su distribuidor. • Con esta unidad no es posible utilizar una antena motorizada sin caja de relé. Conexión para protección de la memoria Si conecta el cable de fuente de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague el interruptor de encendido. Notas sobre la conexión de los altavoces • Antes de conectar los altavoces, desconecte la alimentación de la unidad. • Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de potencia adecuada para evitar que se dañen. • No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. • No conecte el cable de conexión a masa de esta unidad al terminal negativo (–) del altavoz. • No intente conectar los altavoces en paralelo. • Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. • Para evitar fallos de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si su unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo. • No conecte los cables de altavoz de la unidad entre sí. Nota sobre la conexión Si el altavoz no está conectado correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión del altavoz.
7 Al terminal de alimentación de +12 V que recibe energía sin interrupción Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil.
www
.
xiaoy u163. com
6 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
Red Rojo
4
QQ
QQ
Green/black striped Con rayas verdes y negras
*1 Cable con terminales RCA (no suministrado) *2 AUDIO OUT (Salida de audio) puede cambiarse a SUB (Secundaria) o REAR (Posterior). Para obtener información, consulte el manual de instrucciones suministrado. 3 * Insertar con el cable hacia arriba.
13942296513
13942296513
Max. supply current 0.3 A Corriente máx. de alimentación de 0,3 A
TEL
TEL
Blue/white striped Con rayas azules y blancas
AMP REM
3
BUS CONTROL IN
Fuse (10 A) Fusible (10 A)
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 • LOCATION OF CONTROLS (CDX-GT51W: CND/GT510) Location of controls and basic operations Main unit
12 3
4
OFF
67
5
OPEN
PUSH SELECT
DSO
SOURCE
SEEK
AUX
SEEK
EQ3
GP/ALBM
DSPL
1
REP
SHUF
3
4
2
8 9 q; qa qs qd
PAUSE
5
6
qf
SCRL
qg
CDX-GT510 CDX-GT51W
Front panel removed
qh
qj
The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4).
I Receptor for the card remote commander
ql < (.)/, (>) buttons To control CD/radio, the same as (SEEK) –/+ on the unit.
J SEEK –/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold).
MODE CAT BTM
H EQ3 (equalizer) button 9 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).
K BTM/CAT*2 button 8 To start the BTM function (press and hold).
qk
L MODE button 8, 11 To select the radio band (FM/AM); select the SAT tuner band (mode)*2; select the unit*3. M DSPL (display) button 8 To change display items.
1 4 ql
OFF
wa ws qs
ATT
SOURCE
SEL
MODE
+
wd –
qd
qg
SCRL
DSPL 1 4
2
3
5
6
wf
A OFF button To power off; stop the source.
O SCRL (scroll) button 8 To scroll the display item.
B DSO button 4 To select the DSO mode (1, 2, 3 or OFF). The larger the number, the more enhanced the effect.
wd M (+)/m (–) buttons To control CD, the same as (1)/(2) (GP/ALBM –/+) on the unit. wf Number buttons To receive stored stations (press); store stations (press and hold). When an MD changer is connected. When the SAT tuner is connected. When a CD/MD changer is connected. When an ATRAC CD is played. When an MP3/WMA/AAC is played. If the changer is connected, the operation is different, see page 11. *7 When playing back on this unit. *1 *2 *3 *4 *5 *6
Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first. Tip For details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 14.
P RESET button 4
C Volume control dial/select button 9 To adjust volume (rotate); select setup items (press and rotate). D SOURCE button To power on; change the source (Radio/CD/ MD*1/AUX/SAT*2).
Q Z (eject) button 5 To eject the disc. R Disc slot 5 To insert the disc.
E Display window
+
w;
Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.
ws SEL (select) button The same as the select button on the unit.
13942296513
13942296513
Card remote commander RM-X151
wa ATT (attenuate) button To attenuate the sound. To cancel, press again.
TEL
TEL
RESET
N Number buttons CD/MD*1: (1)/(2): GP*4/ALBM*5 –/+ To skip albums (press); skip albums continuously (press and hold).*6 (3): REP 8, 11 (4): SHUF 8, 11 (6): PAUSE*7 To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold).
w; VOL (volume) +/– button To adjust volume.
VOL
F AUX input jack 10 To connect a portable audio device.
QQ 376315150 892498299
7
376315150 892498299
376315150 892498299
TEL 13942296513
G OPEN button 5
6
QQ
QQ
–
• CONNECTIONS (CDX-GT51W: CND/GT510)
Connection example Notes (B-A) • Be sure to connect the ground (earth) lead before connecting the amplifier. • The alarm will only sound if the built-in amplifier is used.
A
Tip (B-B- ) For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary.
AUDIO OUT REAR*
Exemple de raccordement Remarques (B-A) • Raccordez d’abord le câble de mise à la masse avant de raccorder l’amplificateur. • L’alarme est émise uniquement lorsque l’amplificateur intégré est utilisé.
* AUDIO OUT SUB/REAR
B
Conseil (B-B- ) Dans le cas du raccordement de deux changeurs de CD/MD ou plus, le sélecteur de source XA-C40 (non fourni) est requis.
BUS AUDIO IN
BUS CONTROL IN
www
xiaoy u163. com
BUS AUDIO IN
Source selector* Sélecteur de source* XA-C40
.
BUS CONTROL IN
* not supplied non fourni
7 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 *1
Source selector (not supplied) Sélecteur de source (non fourni)
Supplied with the CD/MD changer Fourni avec le changeur de CD/MD
XA-C40
Supplied with XA-C40 Fourni avec le XA-C40
*1 AUDIO OUT FRONT
REMOTE IN
*3 BUS AUDIO IN
L R BUS AUDIO AUDIO OUT IN REAR
from car antenna (aerial) à partir de l’antenne de la voiture
AUDIO OUT REAR*2
AUDIO OUT FRONT
*1 RCA pin cord (not supplied) *2 AUDIO OUT can be switched SUB or REAR. For details, see the Operating Instructions. *3 Insert with the cord upwards.
2
13942296513
1
White Blanc Blue Bleu
Left Gauche
ANT REM
2
White/black striped Rayé blanc/noir Gray Gris
Max. supply current 0.1 A Courant max. fourni 0,1 A Light blue Bleu ciel
ATT
Right Droit Gray/black striped Rayé gris/noir
Orange/white striped Rayé orange/blanc
ILLUMINATION
Green Vert Left Gauche
Purple Mauve
Right Droit
Yellow Jaune
Purple/black striped Rayé mauve/noir
Connection diagram 1 To a metal surface of the car First connect the black ground (earth) lead, then connect the yellow and red power supply leads.
2 To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster Notes • It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). • When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.”
3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit.
4 To the interface cable of a car telephone 5 To a car’s illumination signal Be sure to connect the black ground (earth) lead to a metal surface of the car first.
6 To the +12 V power terminal which is energized in the accessory position of the ignition switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. • When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.”
7 To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first.
Notes on the control and power supply leads • The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna (aerial) in the rear/ side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. • A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly.
5 6
QQ 376315150 892498299 7
Schéma de raccordement 1 À un point métallique de la voiture Branchez d’abord le câble de mise à la masse noir et, ensuite, les câbles d’entrée d’alimentation jaune et rouge.
2 Vers le câble de commande d’antenne électrique ou le câble d’alimentation de l’amplificateur d’antenne Remarques • Il n’est pas nécessaire de raccorder ce câble s’il n’y a pas d’antenne électrique ni d’amplificateur d’antenne, ou avec une antenne télescopique manuelle. • Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».
3 Au niveau de AMP REMOTE IN de l’amplificateur de puissance en option Ce raccordement s’applique uniquement aux amplificateurs. Le branchement de tout autre système risque d’endommager l’appareil.
4 Vers le cordon de liaison d’un téléphone de voiture 5 Vers le connecteur du signal d’éclairage de la voiture Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.
6 À la borne +12 V qui est alimentée quand la clé de contact est sur la position accessoires Remarques • S’il n’y a pas de position accessoires, raccordez la borne d’alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule. • Si votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, voir « Remarques sur les câbles de commande et d’alimentation ».
7 À la borne +12 V qui est alimentée en permanence
Remarques sur les câbles de commande et d’alimentation • Le câble de commande d’antenne électrique (bleu) fournit une alimentation de + 12 V CC lorsque vous mettez la radio sous tension. • Lorsque votre voiture est équipée d’une antenne FM/AM intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) à la borne d’alimentation de l’amplificateur d’antenne existant. Pour plus de détails, consultez votre détaillant. • Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le câble d’entrée d’alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d’arrêt. Remarques sur le raccordement des haut-parleurs • Avant de raccorder les haut-parleurs, mettez l’appareil hors tension. • Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité électrique adéquate pour éviter de les endommager. • Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes des hautparleurs droit à celles du haut-parleur gauche. • Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur. • N’essayez pas de raccorder les haut-parleurs en parallèle. • Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des haut-parleurs peut endommager l’appareil. • Pour éviter tout problème de fonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil partage un câble négatif commun (–) pour les hautparleurs droit et gauche. • Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil. Remarque sur le raccordement Si les haut-parleurs et l’amplificateur ne sont pas raccordés correctement, le message « FAILURE » s’affiche. Dans ce cas, assurez-vous que les haut-parleurs et l’amplificateur sont bien raccordés.
Raccordez d’abord le câble de mise à la masse noir à un point métallique du véhicule.
www
.
xiaoy u163. com
8 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513
Red Rouge
4
QQ
QQ
Green/black striped Rayé vert/noir
*1 Cordon à broche RCA (non fourni) *2 AUDIO OUT peut être commuté sur SUB ou REAR. Pour obtenir plus de détails, reportez-vous au mode d’emploi. *3 Insérez avec le câble vers le haut.
13942296513
Black Noir
Max. supply current 0.3 A Courant max. fourni 0,3 A
TEL
TEL
Blue/white striped Rayé bleu/blanc
AMP REM
3
BUS CONTROL IN
Fuse (10 A) Fusible (10 A)
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 • LOCATION OF CONTROLS (CDX-GT560: E, MX/GT560S) Location of controls and basic operations Main unit
12 3
4
OFF
67
5
OPEN
PUSH SELECT
DSO
SOURCE
SEEK
AUX
SEEK
GP/ALBM
BTM
DSPL
1
8 9 q; qa qs qd
REP
SHUF
3
4
2
qf
PAUSE
5
6
qg
SCRL
qh
CDX-GT560S CDX-GT560
Front panel removed
qj
qk
The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4).
I Receptor for the card remote commander
w; < (.)/, (>) buttons To control CD/radio, the same as (SEEK) –/+ on the unit.
J SEEK –/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold).
MODE
EQ3
H EQ3 (equalizer) button 9 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).
K BTM button 8 To start the BTM function (press and hold).
ql
L MODE button 8, 11 To select the radio band (FM/AM); select the unit*2. M DSPL (display) button 8 To change display items.
RESET
1 4 w;
OFF
SOURCE
ws wd qs
ATT
SEL
MODE
+
wf –
qd
qh
SCRL
DSPL 1
2
3
4
5
6
wg
A OFF button To power off; stop the source. B DSO button 4 To select the DSO mode (1, 2, 3 or OFF). The larger the number, the more enhanced the effect. C Volume control dial/select button 9 To adjust volume (rotate); select setup items (press and rotate).
P SCRL (scroll) button 8 To scroll the display item.
D SOURCE button To power on; change the source (Radio/CD/ MD*1/AUX).
R Z (eject) button 5 To eject the disc.
VOL
–
Tip For details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 14.
QQ 376315150 892498299
7
376315150 892498299
376315150 892498299
TEL 13942296513
Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.
QQ
QQ
G OPEN button 5
When an MD changer is connected. When a CD/MD changer is connected. When an ATRAC CD is played. When an MP3/WMA/AAC is played. If the changer is connected, the operation is different, see page 11. *6 When playing back on this unit. *1 *2 *3 *4 *5
S Disc slot 5 To insert the disc.
F AUX input jack 10 To connect a portable audio device.
6
wg Number buttons To receive stored stations (press); store stations (press and hold).
Q RESET button 4
E Display window
+
wa
O Number buttons CD/MD*1: (1)/(2): GP*3/ALBM*4 –/+ To skip albums (press); skip albums continuously (press and hold).*5 (3): REP 8, 11 (4): SHUF 8, 11 (6): PAUSE*6 To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold).
Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.
wd SEL (select) button The same as the select button on the unit. wf M (+)/m (–) buttons To control CD, the same as (1)/(2) (GP/ALBM –/+) on the unit.
13942296513
13942296513
Card remote commander RM-X151
ws ATT (attenuate) button To attenuate the sound. To cancel, press again.
TEL
TEL
N Frequency select switch (located on the bottom of the unit) See “Frequency select switch” in the supplied installation/connections manual.
wa VOL (volume) +/– button To adjust volume.
• CONNECTIONS (CDX-GT560: E, MX/GT560S)
Connection example Notes (B-A) • Be sure to connect the ground (earth) lead before connecting the amplifier. • The alarm will only sound if the built-in amplifier is used.
A
Tip (B-B- ) For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary.
AUDIO OUT REAR*
Ejemplo de conexiones Notas (B-A) • Asegúrese de conectar primero el cable de conexión a masa antes de realizar la conexión del amplificador. • La alarma sonará únicamente si se utiliza el amplificador incorporado.
* AUDIO OUT SUB/REAR
B
Sugerencia (B-B- ) Si desea conectar dos o más cambiadores de CD/MD, necesitará el selector de fuente XA-C40 (no suminidtrado).
BUS AUDIO IN
BUS CONTROL IN
(B-A) • • B-B-
www
xiaoy u163. com
BUS AUDIO IN Source selector* Selector de fuente* * XA-C40
.
BUS CONTROL IN
* not supplied no suministrado
9 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 *1
Source selector (not supplied) Selector de fuente (no suminidtrado) Supplied with XA-C40 Suministrado con el XA-C40
Supplied with the CD/MD changer Suministrado con el cambiador de CD/MD
XA-C40
*1 AUDIO OUT FRONT
REMOTE IN
*3 BUS AUDIO IN
L R BUS AUDIO AUDIO OUT IN REAR
from car antenna (aerial) desde la antena del automóvil
AUDIO OUT FRONT
AUDIO OUT REAR*2
BUS CONTROL IN
Fuse (10 A) Fusible (10 A)
2
3
Black Negro
1 White Blanco
Left Izquierdo
Blue Azul
ANT REM
White/black striped Con rayas blancas y negras
2 Light blue Azul celeste
Grey Gris
Right Derecho
Max. supply current 0.1 A Corriente máx. de alimentación de 0,1 A ATT
Grey/black striped Con rayas grises y negras
ILLUMINATION
5 6
QQ
376315150 892498299 7
Diagrama de conexión
Connection diagram
1 A una superficie metálica del automóvil
1 To a metal surface of the car First connect the black ground (earth) lead, then connect the yellow and red power supply leads.
2 To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster Notes • It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). • When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.”
3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit.
4 To the interface cable of a car telephone 5 To a car’s illumination signal Be sure to connect the black ground (earth) lead to a metal surface of the car first.
6 To the +12 V power terminal which is energized in the accessory position of the ignition switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. • When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see “Notes on the control and power supply leads.”
7 To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first. Notes on the control and power supply leads • The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna (aerial) in the rear/ side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. • A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker leads to each other.
.
Note on connection If speaker and amplifier are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifier are connected correctly.
1
Conecte primero el cable de conexión a masa negro, y después los cables amarillo y rojo de entrada de alimentación.
2 Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de señal de la antena Notas • Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.
3 A AMP REMOTE IN de un amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad.
2 • •
3 4 5 6
4 Al cable de interfaz de un teléfono para automóvil 5 A una señal de iluminación del automóvil
•
Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil.
6 Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de la llave de encendido Notas • Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. • Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte “Notas sobre los cables de control y de fuente de alimentación”.
7 Al terminal de alimentación de +12 V que recibe energía sin interrupción Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. Notas sobre los cables de control y de fuente de alimentación • El cable de control de la antena motorizada (azul) suministrará cc de + 12 V cuando conecte la alimentación del sintonizador. • Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de entrada de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener más información, consulte a su distribuidor. • Con esta unidad no es posible utilizar una antena motorizada sin caja de relé.
•
7 • • •
• • • • • • • •
Conexión para protección de la memoria Si conecta el cable de entrada de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague el interruptor de encendido. Notas sobre la conexión de los altavoces • Antes de conectar los altavoces, desconecte la alimentación de la unidad. • Utilice altavoces con una impedancia de 4 a 8 con la capacidad de potencia adecuada para evitar que se dañen. • No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. • No conecte el cable de conexión a masa de esta unidad al terminal negativo (–) del altavoz. • No intente conectar los altavoces en paralelo. • Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. • Para evitar fallas de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si la unidad comparte un cable negativo común (–) para los altavoces derecho e izquierdo. • No conecte los cables de altavoz de la unidad entre sí.
xiaoy u163. com
Nota sobre la conexión Si el altavoz y el amplificador no están conectados correctamente, aparecerá “FAILURE” en la pantalla. Si es así, compruebe la conexión de ambos dispositivos.
10 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
Purple/black striped Con rayas moradas y negras
QQ
QQ
Yellow Amarillo
Purple Morado
TEL 13942296513
www
*3
Red Rojo
Green/black striped Con rayas verdes y negras
Right Derecho
*1 *2
4
Orange/white striped Con rayas naranjas y blancas
Green Verde
Left Izquierdo
*1 Cable con terminales RCA (no suministrado) *2 AUDIO OUT (Salida de audio) puede cambiarse a SUB (Secundaria) o REAR (Posterior). Para obtener información, consulte el manual de instrucciones suministrado. *3 Insertar con el cable hacia arriba.
13942296513
13942296513
Max. supply current 0.3 A Corriente máx. de alimentación de 0,3 A
TEL
TEL
Blue/white striped Con rayas azules y blancas
AMP REM
*1 RCA pin cord (not supplied) *2 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. *3 Insert with the cord upwards.
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S Ver. 1.2 SECTION 2 DISASSEMBLY
QQ 376315150 892498299 Note: This set can be disassemble according to the following sequence.
SET
2-1.
SUB PANEL ASSY (Page 12)
2-2.
CD MECHANISM BLOCK (Page 12)
2-3.
MAIN BOARD (Page 13)
2-5.
CHASSIS (T) SUB ASSY (Page 14)
2-6.
ROLLER ARM ASSY (Page 14)
2-7.
CHASSIS (OP) ASSY (Page 15)
13942296513
13942296513
SERVO BOARD (Page 13) TEL
TEL
2-4.
QQ
QQ
1. CHUCKING ARM SUB ASSY (SUPPLEMENT-1 Page 1)
QQ 376315150 892498299
376315150 892498299
376315150 892498299
TEL 13942296513
2. SLED MOTOR ASSY (SUPPLEMENT-1 Page 2) 3. OPTICAL PICK-UP SECTION (SUPPLEMENT-1 Page 3) 4. OPTICAL PICK-UP (SUPPLEMENT-1 Page 3)
www
.
xiaoy u163. com 11 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299
Note: Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL ASSY
3 two claws
TEL
TEL 4 flexible flat cable (20 core) (CN802)
1 two screws (+PTT 2.6 × 6) 5 sub panel assy
7 CD mechanism block
6 bracket (CD)
5 two screws (+PTT 2.6 × 4)
3 2 screw (+PTT 2.6 × 6)
4 CN350
www
xiaoy u163. com 1 screw (+PTT 2.6 × 6)
.
12 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
2-2. CD MECHANISM BLOCK
QQ
QQ
QQ 376315150 892498299
TEL 13942296513
13942296513
13942296513
2 two claws
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 2-3. MAIN BOARD
4 screw (+PTT 2.6 × 10)
5 two screws (+P 2.6 × 8)
6 two screws (+P 2.6 × 8) 7 two screws (+PTT 2.6 × 10)
1 three ground point screws (+PTT 2.6 × 6)
2 two screws (+PTT 2.6 × 8) 8 screw (+PTT 2.6 × 10) 9 heat sink
TEL
TEL
0 MAIN board
13942296513
13942296513
3
insulating sheet
QQ
QQ
376315150 892498299
376315150 892498299
QQ 376315150 892498299
TEL 13942296513 2-4. SERVO BOARD
WHT RED BLK WHT RED BLK RED ORG BLU YEL GRY
2 toothed lock screw (M 1.7 × 2.5) 3 toothed lock screw (M 1.7 × 2.5)
SERVO board 5 SERVO board
1 Remove the eleven solders.
4 optical pick-up (16 core) (CN1)
claw
www
xiaoy u163. com claw
.
13 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299
2-5. CHASSIS (T) SUB ASSY
2 two precision screws (+P 1.7 × 2.2)
1 two precision screws (+P 1.7 × 2.2)
4 chassis (T) sub assy
TEL
TEL
13942296513
13942296513
3 claw
2-6. ROLLER ARM ASSY
5 roller arm assy
4 gear (RA1) 1 spring (RAL)
www
3 washer
xiaoy u163. com 2 spring (RAR)
.
14 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S Ver. 1.2
QQ 376315150 892498299 2-7. CHASSIS (OP) ASSY
6 chassis (OP) assy
1 tension spring (KF) 5 7 coil spring (damper) (natural) 8 coil spring (damper) (green) 4 slider (R)
TEL
TEL
13942296513
13942296513
3 lever (D)
2 gear (LE1)
.
QQ 376315150 892498299
376315150 892498299
376315150 892498299
www
QQ
QQ
TEL 13942296513
xiaoy u163. com 15 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S SECTION 3 DIAGNOSIS FUNCTION
QQ 376315150 892498299
Description of the Diagnostics function:
4. Contents of each display mode 4-1. Reset count display mode
1. Setting the Diag display mode
With the power off, press the [4/SHUF] button, [5] button, and [4/SHUF] button on the set body or the remote control (for more than 2 seconds) in turn.
2. Canceling the Diag display mode During the Diag function mode, press the [OFF] button.
3. Initial display in the Diag display mode. Just when the Diag mode is entered, “reset count” is displayed. The display mode is switched by each rotation of M >/SEEK + or . m/SEEK – buttons.
XX
Reset count (in hexadecimal format) Diag code 01: Reset count
4-2. Reset count by watchdog timer display mode
02
XX
Diag code 02: Number of resets by watchdog timer
XX
02
XX
Number of connected units display
XXX
376315150 892498299
Operating hours display
04
XXXX
Show the number of connected units for CD-C, MD-C and XM respectively from the rightmost (in hexadecimal format). Recency of information 1-3: 1 represents the latest. Diag code 03: Number of connected unit.
QQ 376315150 892498299 The display mode is switched by each rotation of [2/GP/ALBM +] or [1/GP/ALBM --] buttons during the number of connected units display mode.
CD error information display No. of connected units history 1 (latest) display
051
XX
031
XXX
OFFSET/FAILURE error display No. of connected units history 2 display
061XXXXX
032
XXX
No. of connected units history 3 display
033
XXX
4-4. Operating hours display mode
04
www
XXXX
xiaoy u163. com Operating hours (in hexadecimal format)
.
Diag code 04: Operating hours
16 http://www.xiaoyu163.com
376315150 892498299
TEL 13942296513
XXX
QQ
QQ
031
031
13942296513
13942296513
4-3. Number of connected units display mode Reset count by watchdog timer display
TEL
TEL
Reset count (in hexadecimal format)
Reset count display
01
01
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 4-5. CD error information display mode 4-5-1. Error description
4-6. OFFSET/FAILURE error display mode
061XXXXX
051
XX
Error information
Error description Indication Description (in hexadecimal 1X SERVO ERROR format) 3X LOADING ERROR Recency of information 4X TRACK JUMP 1-3: 1 represents the latest. 5X TEXT ERROR Diag code FX MECHA ERROR 05: CD error information
Operating hours Error description (0: OFFSET, 1: FAILURE) Recency of information 1-3: 1 represents the latest. Diag code 06: OFFSET/FAILURE
The display mode is switched by each rotation of [2/GP/ALBM +] or [1/GP/ALBM --] buttons during the OFFSET/FAILURE error display mode.
4-5-2. Disc type and operating hours
OFFSET/FAILURE error history 1 (latest) display
Disc type Indication 0 1 2 3 8 F
Disc type MP3 WMA AAC ATRAC CD/DA UNKNOWN
The display mode is switched by each rotation of [2/GP/ALBM +] or [1/GP/ALBM --] buttons during the CD error information display mode.
061XXXXX
13942296513
13942296513
Operating hours Disc type Recency of information 1-3: 1 represents the latest. Diag code 05: CD error information
OFFSET/FAILURE error history 2 display
062XXXXX OFFSET/FAILURE error history 3 display
QQ
QQ
063XXXXX
CD error info history 1 (latest) Error description plus error details display
051
QQ 376315150 892498299
376315150 892498299
376315150 892498299
TEL 13942296513 XX
CD error info history 1 (latest) Disc type plus operating hours display
051XXXXX CD error info history 2 Error description plus error details display
052
XX
CD error info history 2 Disc type plus operating hours display
052XXXXX CD error info history 3 Error description plus error details display
053
www
XX
xiaoy u163. com
CD error info history 3 Disc type plus operating hours display
.
053XXXXX
17 http://www.xiaoyu163.com
TEL
TEL
051XXXXX
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 MEMO
TEL
TEL
13942296513
13942296513
.
xiaoy u163. com
18 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
www
QQ 376315150 892498299
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
SECTION 4 DIAGRAMS
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-1. BLOCK DIAGRAM — MAIN SECTION —
J451 (2/2) L J451 (1/2) BUS AUDIO IN
FRONT
ELECTRONIC VOLUME IC401
AUDIO OUT
L R-CH
2 A2 1 A1
OUTS2 21 OUTS1 22
L REAR
R-CH
R-CH
R
MUTE Q430
R-CH R-CH
9 DP2 7 DP1 8 DN
L 4 R 3
1 ANT
R-CH
SOUT 19 CLK 17 DATA 18
R-CH
6 C2 5 C1
SCL 29 SDA 30
1 FL+ 9 FL-
MUTE Q440
SA_IN SA_CLK SA_DATA
MUTE Q470
LR+ 9 LR- 7
2 RL+ 10 RL-
R-CH
D491 MUTE DRIVE Q491,492
BATT
12C-SCL 12C-SDA
5 4 SCL 2 SDA
SW1 29 SW2 27
FU601
16
VP 35
QUALITY 5
CNP350 11 15 21 22 24 26 16 5 7 28 6 27 25 9 18 19 8 1,2
BATT
SCL SDA
QQ
I2C_CKO 33 I2C_SIO 34
25 EEP_CKO 24 EEP_SIO
SA_IN 44 SA_CLO 45 SA_DATA 32
SA_IN SA_CLK SA_DATA
3 7 6 3 1 5 1 5 0
38 QUALITY
AU_LCH AU_RCH EJECT_OK UNISO UNISI UNICLK Z-MUTE CD-ON CDM-ON LINK_OFF SYS_RST BUS_ON B/U_CHECK A-ATT D_3.3V A_3.3V BU_3.3V DR_6V
BEEP 5 AMPSTB 26 DIAG 8
D511
SYSRST
UNSON BUIN
REG1 REG3 REG4 REG5
AU8V SERVO3.3V MECHA6V DISP+B (+9V)
UNISO UNISI UNISCK Z-MUTE CD_ON CDM_ON
14 ILL 13
TEL-ATT DETECT Q701
TEL ATT 74
7
ACC DETECT Q702
ACC_IN 72 TEST IN 73
TEL-MUTE ACC
15
D400
88 77 87 54
SYSRST RESET BUSON BUIN
OPEN-MUTE 100
BUS INTERFACE CONTROL IC601 SYSRST BUSON UNISCK BUIN UNISI UNISO
D493
ATT 86
SERVO3.3V RESET IC602
BU_3.3V MECHA6V
1 VOUT
VDD 2
13 12 11 10 8 9
RST BATT BUSON CLK-IN DATA I/O B/U-C DATA OUT CLK DATA IN RST
TEST
BATT BATTERY CHECK Q605
3
6 4 2
A
x ia o y u 1 6 3
CDX-GT51W/GT510/GT560/GT560S
19 19 http://www.xiaoyu163.com
DISPLAY SECTION
(Page 20)
D494
.
TH400
3.3V REG. IC502 +3.3V
DOOR_SW
CNJ400 (BUS CONTROL IN)
LINK ON/OFF CONTROL Q600,601
LINK_OFF
: FM/AM
3 2 1 7
BUS.ON 1
: CD PLAY
8
D602 6 5 4
BU 3.3V
• R-CH is omitted due to same as L-CH. • Signal Path
.
30 31 33 34
D603
S103 RESET
: AUX
U-COM (+5V) BU3.3V
ILL DETECT Q703
ILLUIN 75 59 58 60 93 98 99
UNISI UNISCK
LINK_OFF
8 9 2 4 9 8 2 9 9
89 EJECT_OK_SW
UNISO
R-CH
16 ACGND 22 STB 25 DIAG
REG2 37
c o
3 VOUT
m
TU+5V
VIN 2
+5V REG. Q3
BATT U-COM (+5V)
AU8V
376315150 892498299
376315150 892498299
EEPCKO EEPSIO
E2PSCL 16 E2PSDA 17
39 VSM 12 TU ATT
QQ
QQ
VSM TUATT
AMP-R ANT-R
6
SYSTEM CONTROL IC501 (1/2)
1 3 9 4 2 2 9 6 5 1 3
www
4 FR+ 12 FR3 RR+ 11 RR-
B-CH
SCL SDA
13942296513
13942296513
4 B2 3 B1
10 VCC8.3V 11 VDD5V 15 E2PVDD S-METER 6 TUN_MUTE 7
CD MECHANISM UNIT (MG-101FA)
R-CH
R-CH (FRONT) R-CH (REAR)
CN601
LF+ 5 LF- 3
12 IN-RR 11 IN-RF
12C-SCL 12C-SDA
SCL 13 SDA 14 AU8V TU+5V +3.3V
25 23 26 24
POWER AMP/MULTIPLE VOLTAGE REGULATOR IC300
TEL
TEL
OUTF2 OUTR2 OUTF1 OUTR1
TU1 (TUNER UNIT) J1 (ANTENNA)
R
R-CH
J901 AUX
TEL
R
R-CH
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 3 7 6 3 1 5 1 5 0
4-2. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL IC501 (2/2)
RC1
Q991–993 FL DRIVE
71 RC_IN1
J370
8 9 2 4 9 8 2 9 9
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
Q993
( REMOTE ) IN
RC0
43 RC_IN0
12 DI 11 CL 10 CE
FL_SO 19 FL_SCL 20 FL_CS 18
D501
GRID1 28 FL900 FLUORESENT INDICATOR TUBE
1G 33
Q992
GRID2 27
40 KEYIN1
KEY MATRIX S909–917 S902–904,906–908
13 RESET 41 KEYIN0
+3.3V FL12V
2G 34
8 VDD 7 VH
Q991
GRID3 26
For schematic diagrams.
For printed wiring boards.
Note: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : internal component. • C : panel designation.
Note: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. a : Through hole. • : Pattern from the side which enables seeing. • (The other layers' patterns are not indicated.)
TEL
S201
Z
KEY ACKNOWLEDGE SWITCH Q501
DISP+B (+9V)
52 KEY ACK
LED952–954, 956–967, 991–994 KEY ILLUMINATE
76 AD_ON
+
ROTARY ENCODER
(
RE-0 RE-1
LED902–904, 906–917, 941–944 KEY ILLUMINATE
)
(
48 RE-IN1 47 RE-IN0 79 XOUT
)
• • • •
Q941
X501 32.768kHz 80 XIN 82 OSCIN
1 3 9 4 2 2 9 6 5 1 3
X500 18.432MHz
83 OSCOUT DOOR_IND 46
CN201 18
LED DRIVE Q589,590
70 DOOR_SW
QQ •
LED201 (DISC IN) LED202 (Z )
• •
REMOTE CONTROL SIGNAL RECEVER IC971 MAIN SECTION
A
2 OUT
SIRCS 64
DOOR_SW
•
(Page 19)
+12V REG. IC801 FL12V
4 VOUT
VIN 5
BATT
C Q
These are omitted
B E
BE C These are omitted
3 7 6 3 1 5 1 5 0
ECB
8 9 2 4 9 8 2 9 9
These are omitted
• Abbreviation CND : Canadian model. EA : Saudi Arabia model. MX : Mexican model.
CONT 5 FL12V_ON 65 BU+3.3V FSW_IN 10
(
S501 FREQUENCY SELECT
FL12V_ON DC/DC CONVERTER IC802
FSW_IN
10K
) 9K
GT560:E,MX/GT560S
5 INV 2 SW
+3.3V
3 AREASEL2
FSW_OUT 66
DD_ON
FSW_OUT
• Waveforms — MAIN Board —
D801
DD_ON 67
V_IN 1
7 EN 6 RT
1
IC501 id (OSCOUT)
Q801
3Vp-p
0.6Vp-p
• Abbreviation MX : Mexican model
www
2
IC501 ul (XOUT)
32.768kHz
18.432MHz
0.2 V/DIV, 20 µsec/DIV
.
x ia o y u 1 6 3
CDX-GT51W/GT510/GT560/GT560S
20 20 http://www.xiaoyu163.com
1 V/DIV, 50 nsec/DIV
.
c o
m
376315150 892498299
376315150 892498299
CN901 18
•
A : B+ Line. B : B– Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : TUNER < > : CD PLAY ∗ : Impossible to measure Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD PLAY F : TUNER g : BUS AUDIO L : AUX Abbreviation CND : Canadian model. EA : Saudi Arabia model. MX : Mexican model.
Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
QQ
QQ
TEL
Q942
Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié.
13942296513
13942296513
RE901 PUSH SELECT (VOLUME)
Q1 32
TEL
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
3G 35 Q2 31
Caution: Pattern face side: (Side B) Parts face side: (Side A)
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0 4
5
6
7
8 9 2 4 9 8 2 9 9
8
9
J451
AUDIO OUT
-1
REAR
-2
FRONT
-1
-2
-1
J370 (REMOTE IN) CNJ400 (BUS CONTROL IN)
-2
R432
R452
R442
R422
JW3
C309 C307
FU601 C301
C304
C305
L301
C452
JW1
C323
C602
C432
JW4
B
C324 JW2
CNJ400
CN300
B14.4V
JC301
C413
C414
C422
JC300
JC302
JC999
R474 C442
D104
D105
D106
D107
D115
C114
D114
.A
JW8 JW9
D703
D302
R702
D301
D309
D312
D311
D308
D310 JW33
C313 C314
JW35
FB402
C405
L303 R603
Q605
R604 Q600
4
3
C401
R705
S103
S103 RESET
(Page 25)
CDX-GT51W/GT510/GT560/GT560S
21 21 http://www.xiaoyu163.com
C702
R707 JW85
IC601
C809
1 C802
7
C812
R601
JW86 R534
JW89
JW88 R533
R532
JW87
R711
R553 JW90 FB801
IC602
R607 R605
D801
R801 R802 R803 R809
FB802
.
JW84
R606
C601
FB803
L803
JW83
R708
JC600
R602
R806 R808
JW82
D702
Q702
R830
JC519
C804
D705
L802 C519
JW117
C805
R531
D511 JC804
JW91
JW92
JW95
JW96
R551 JW97 JW118
JC524
R527 C998
R543
R706
IC802
R407
JW94 JW93
D400
C703
C821
C103
R608
C402
R562
L500
JC53
JW120
4 C817
JW119
JW121
JW123
JW122 5
2 1
IC801
JW124 R522 3
R810 R812
5 1
R563 JW74
JW77
JW75
JW76 R547
FB804
Q501
C816
R524
R523 R556
R555
JC511
JC602
JW72 JW73
Q801
D493 R537
50 IC
C507
R526
D802 D502
D602
C417
FB407
JW54
JW53
C502 JW55 D494
JW56
JW156
1
R528
D116
SUB BOARD CN202
C701 D607
JW10
JW11
JW157
JW12
JW13
JW14
JW34
JW36 JW37
JW38
JW100
R516 JC516 R545
C511 C510
C513 JW138
JW131
R535 JW130 D501
R541
R550 R525
JW127
JW150
C117
R546
x ia o y u 1 6 3 JC100
C108
D103
D108
C116
D102
L101
C104
D120
1 19 D109
JW139
C814
R370
R530
R811
JW153
2
R529
JC603
D604
JW71
R712
Q703
JC512 FMB4
JW134
Q589
CN802
20
www (CHASSIS)
JW152
X500 C515
C512
JW132
C110
R400
C516
R538
JW69
R351
R536
R371
D704
C415
C505
C508
C705
FB404
R512
C509
D119 JW141
C109
JC800
Q590
R558
JC508
JW140
R557
D110
FB406
JC350
X501
R539
R519 R520
D101
JC515
JC514 R514
C523
JW135
JC501
JW143
JW159
JW144
JW145
JW146
JW147
R500
D603
R710
R401
C506
JC523
R517
JW137
GT560:E,MX/GT560S
R509
FB408 JW51
C810 C813 R804
C819 C811 R805
C997
S102
c o
S102 (FRONT PANEL DETECT)
m
1-871-694-
IC300 IC401 IC501 IC502 IC601 IC602 IC801 IC802
B-6 E-4 H-6 E-6 H-10 I-9 I-7 I-11
Q3 Q420 Q430 Q440 Q450 Q460 Q470 Q491 Q492 Q501 Q589 Q590 Q600 Q601 Q605 Q701 Q702 Q703 Q801
G-2 C-4 C-3 C-3 C-4 C-4 D-4 E-5 E-5 I-7 I-2 I-2 G-11 G-11 F-10 D-8 H-10 H-9 I-10
8 9 2 4 9 8 2 9 9 CD MECHANISM UNIT (MG-101FA)
JW50
FB405
FMB3
R513
R518 R548
JW103 R515
10K
JC503
JW148
JW105 JW104
JW108
JW109 R549
JW112 S501
I
R504 R503
C504
R540
JW113
JW111
H
FB403
C418 R505
R508
R611
3 7 6 3 1 5 1 5 0
C412 R402
C410
C419
JW101
JW80
JC522
R521
9K
JW160
JW47
R560
JW102
R455 R484
JW110
JC32
R302
E,MX R510 MODEL R507
FB401 C403
R559 R501 R494
L4
JW114
JW61
FREQUENCY SELECT
JW115
JW154
JW39
JW60
QQ
C503
JW64
R7
JW81
C319
JW59
JW46
C830
C481 R453
R454
R6 R554
R482
C5
Q3
C8
R301
JC504
R433 JW62 JW63
L1
R13
JW68
C363
C483
C364
C482
JW58
C600 CN350
C315
IC502
JW133
D365
R481 R483
R12 JW67
JC400
JW28 TH400
JW32 C316
C325
JW43
R450
JW107
C7
R480
C480
R430
JW30
JW52
D491
C318
C328
R357
D2
R10
C9
JW29
Location F-2 I-2 J-2 J-4 J-3 J-3 J-3 J-3 J-2 J-2 I-2 J-2 J-3 J-4 I-4 J-4 D-8 D-8 D-9 D-9 D-6 D-6 D-6 D-7 D-7 D-7 D-7 D-7 F-3 E-3 E-3 H-8 E-6 F-7 F-7 I-6 I-6 I-8 F-10 F-10 F-11 C-10 C-10 C-10 D-8 G-10 D-9 F-10 G-9 I-10 I-7 C-9
11
(11)
376315150 892498299
376315150 892498299
F
R709
JW31
C501
JC518
D366
JW66
C2
R491
R460
R358
JC3
J
C491 Q491
JW57
R470
Q492
R420
C327
IC401
R5
D307
C306
C331
1 3 9 4 2 2 9 6 5 1 3 JW65
D306
D305
Q470 C451 R440
C317
R4
C485 C484
C330
R361 JC401
C4
C3
G
JW41
C487 D367
L300 C704
Ref. No. D2 D101 D102 D103 D104 D105 D106 D107 D108 D109 D110 D114 D115 D116 D119 D120 D301 D302 D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D365 D366 D367 D400 D491 D493 D494 D501 D502 D511 D602 D603 D604 D605 D606 D607 D701 D702 D703 D704 D705 D801 D802 D803
QQ
QQ
R3
JW40
R451
JW44
C360
C441
C362
R359
JW45
C361
R461
C321
R356
TEL
R471
R704
R703
B14.4V
D304
Q701
C461
R355
E
C471
C431
JC430
C902
D303
JW27
C300
TU1
R2
C308
R431
R472
C901
D701
JW6
• Semiconductor Location
13942296513
13942296513
R441 C421
D903
C310
JW5
D606
JW7
R701
R462
C447
R421
D
JW20
C466
C443
C14
JW18
C303 Q460
JC491
JW26
C312
JW19
C465
(CHASSIS)
C462
C472
C423
JC490
JW16
JW17
JW15
Q420
C320
JW21
C446
Q440
R419
Q450
R418
Q430
JW23
JW24
D605
JC303
Q601
R416
IC300
13
TEL
TEL
C
L302
JC998
R417
12
ORG/WHT
BUS AUDIO IN
J1 (ANTENA)
11
ILL
A
10
R610
3
JW801
2
1
: Uses unleaded solder.
C801
4-3. PRINTED WIRING BOARD — MAIN SECTION —
CDX-GT51W/GT510/GT560/GT560S
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 29 for IC Block Diagram.
C303 JC999 C323 C306 C308
C324 JC504 R302 C319
JC302
C317 JC300 JC301
C304
C301
R301
C305
C307
C309
C318
IC300
TEL
TEL
IC B/D
C462 C472 C465 C466
QQ
1 3 9 4 2 2 9 6 5 1 3 D702
R709
D703
D704
D705
D607
L300
R702
C703
C705
R706
3 7 6 3 1 5 1 5 0 D312
D311
D310
D309
D308
D307
D306
D305
D303
C702
R711 R712
R703 R704
R707 R708
C704 R491
D491 Q491
C701 Q703
Q701
IC502
Q492
Q702
C491 C501
C325 R604
C502
R603
D603 Q600
R608
D602 JW43 Q605
JC602
TH400 C600
Q601
R610
R601 C601
R607 CNJ400 R611
R602
R606
JC603 D604
D605
C602
D606
R605
D511 IC601
IC B/D
www L303
J370
L302
L301
.
x ia o y u 1 6 3 (Page 24)
CDX-GT51W/GT510/GT560/GT560S
22 22 http://www.xiaoyu163.com
.
c o
C310
C320
C312
C314
8 9 2 4 9 8 2 9 9
D304
m
376315150 892498299
376315150 892498299
FU601
D903
C901
R705
QQ
QQ
TEL
R710
C313
C316
C902 D701
C315
R701
D302
D301
(Page 23)
13942296513
13942296513
CN300
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 30 for IC Block Diagram.
J451
J1
TU1
C443 C447
C442
C422
C452
C432
R442
R422
R452
R432
R472
R462
Q470
Q460
C414 JC998
R418
JC303 C423
C413
R416
R419
JW26
C14
R417
R474
C446
Q440
Q420
Q450
R2
R3
Q430
C4 R4
TEL
TEL
R5 JC490
R471
JC491
R461
R441
R421
JC430
C461
C441
C421
R451
R431
C451
C431
C2
Q3
L4
13942296513
13942296513
C471
C3 JC3
R10
C9
C5 D2
C7 JC522
(Page 22)
D366 IC401
D367
R361
JC32
D365 C481
R12 L1
R13
C8
R482 R483
R433
C483
R450
C482
IC B/D
R481
R430
R480
R460
C480
R470
C360
R420
C361
R355
R440
C362
R356
QQ
R6
3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
R7
R357
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
R484
R359 JC401
R358
C364 R455 C485
C484
C363
R454
C328
R453
JC400
C327 C331
C321
C330
C300
C487
CN802
L101
(Page 26)
JW146 JW145
C116
JW144
C117
(Page 24)
CDX-GT51W/GT510/GT560/GT560S
23 23 http://www.xiaoyu163.com
C110
D102
D110
C109
D109
C108
m D108
D114
C114
D115 UDZS-TE-17-6.8B
D107
D106
D105
c o D101
C104
D104 MA8180-M-TX
.
D116
D119 MA8180-M-TX
x ia o y u 1 6 3
C103
.
D120
www
D103 MA8180-M-TX
JC100
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
• Refer to page 20 for Waveforms.
4-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 31 for IC Pin Descriptions.
(Page 22)
(Page 23)
Q590
Q589 IC602
D493
C519
R494
R543 S103
TEL
TEL
D494
JC53
13942296513
13942296513
R551
D501
R546
R530
CN350
R532
R400
JW71
R531
R407
JW93
R534
JW91
R533
R535
FB406
C405
R402 FB403
C417
C410
C419
X501
C516
X500
QQ
R528
R526
R527
3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
R541
R547
R370
1 3 9 4 2 2 9 6 5 1 3
FB408 FB407
JC524
R529
R550
JC512
R525
R555
R401 FB405
R351
C415
JC511
R556
C418
R524 R523
R536
C505
R558 R557
C506 L500 R537
FB404
D400
R521
JC600
FB402
R522
C513
C512
C402
R371
JC350
C401
R553
R539
IC501
C510
R540
C511 C508
R520
R519
JC508
C509 JW801 R563
JC501
C507
R562
R513 R548
IC802 IC801
www C802
C810
C801
C809 D801
C997
JC516
R518
R516
JC514
JC515
JC518
R517
C504
R500
C523
JC519
JC523
C503
C805
R802
R803
R559
JC800
R804 R801
R503
L803
C830
R545
R514
R508 C817
R515
C816 R810
R505
L802
C804
FB804
R554
D802
R830
R509
R806 C819 FB801 R808 JC804
C812
R512
R812
R504 R560
R811
R501
C813
R510
FB802
R809
R507
FB803
C821
C811
C998
R805
R549
S501
S102 Q801
C814
.
x ia o y u 1 6 3
CDX-GT51W/GT510/GT560/GT560S
24 24 http://www.xiaoyu163.com
.
c o
m
JC503
376315150 892498299
376315150 892498299
TEL
FB401
Q501
QQ
QQ
C515 C412 C403
R538
D502
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0 4-7. PRINTED WIRING BOARD — SUB SECTION —
1
2
3
CDX-GT51W/GT510/GT560/GT560S
: Uses unleaded solder.
4
5
6
7
8 9 2 4 9 8 2 9 9 8
9
10
(Page 27) KEY BOARD CN901
A
B LED202, S201
FMA4
B LED202 R202
TEL
TEL
CN201 LED201 R201 S201 LED201 (DISC IN)
D FMA3
1 3E 9 4 2 2 9 6 5 1 3
QQ
3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
(Page 21)
MAIN BOARD CN802
A
F
1
20
G CN202
H
1-871-696-
I
www
.
x ia o y u 1 6 3
CDX-GT51W/GT510/GT560/GT560S
25 25 http://www.xiaoyu163.com
.
c o
m
11 (11)
376315150 892498299
376315150 892498299
TEL
11 (11)
QQ
QQ
1-871-696-
13942296513
13942296513
C
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-8. SCHEMATIC DIAGRAM — SUB SECTION —
CN202
CN201
TEL
TEL R202
(Page 28)
R201
S201 LED202
www
.
QQ
3 7 6 3 1 5 1 5 0
x ia o y u 1 6 3
CDX-GT51W/GT510/GT560/GT560S
26 26 http://www.xiaoyu163.com
.
c o
8 9 2 4 9 8 2 9 9
m
376315150 892498299
376315150 892498299
1 3 9 4 2 2 9 6 5 1 3
QQ
QQ
TEL
LED201
13942296513
13942296513
(Page 23)
http://www.xiaoyu163.com
QQ 3 7 6 3 1 5 1 5 0 4
5
6
A
8 9 2 4 9 8 2 9 9
8
9
R939
S913
S912
S911
IC971 LED917,967, S917 BTM/CAT
R952
39
38
R982
D992
C992
FB991
C991
R981
D988
J901 AUX
CN901
FB971
R986 R985
D984
R987 FL901
26
35
D981
R990
R988
R993
D989
C932 Q993
R992 R991
D982
R959 D994
R983
D990
R984
R994
D993
R903
R933
R929
R931
R966
R995
R955
R949
R902 R901
R963
R905 R904
R909
R962
Q991
R947
R910
R930
Q942
Q992
R948
R935
R950
R937
R938
R908
8 9 2 4 9 8 2 9 9
R911
R932
Q941
RE901
LED909,959, S909 SCRL
R925
R954
R951
R936 R934
H
R912
R926
R927
D931
R907
1-871-695-
5
13
2
1
FLUORESENT INDICATOR TUBE
RE901
I
PUSH SELECT (VOLUME)
B SUB BOARD CN201
• Semiconductor Location
J
Ref. No.
Location
D931 D971 D981 D982 D983 D984 D988 D989 D990
G-8 F-4 G-10 H-5 H-11 G-10 H-9 H-9 G-9
www
Ref. No. D992 D993 D994 IC971
.
LED902 LED903 LED904
Location G-10 H-6 G-13 D-3 B-5 C-5 D-5
Ref. No. LED906 LED907 LED908 LED909 LED910 LED911 LED912 LED913 LED914
Location D-2 C-2 B-2 D-12 D-11 D-10 D-9 D-8 D-7
11 (11)
D983
R956
G
R923
R958
R957
R906
LED910,960, S910 6/PAUSE
R928 R921
R989
R945
R971
R953
R943
R913
R924
R996
R946
R914 R922
R973
D971
C971 R944
LED911,961, S911 5
3 7 6 3 1 5 1 5 0
R915
R916 R972
LED912,962, S912 4/SHUF
1-871-695-
Ref. No. LED915 LED916 LED917 LED941 LED942 LED943 LED944 LED952 LED953
Location D-6 D-6 D-4 B-4 C-4 D-3 C-3 B-5 C-5
376315150 892498299
376315150 892498299
QQ
1 3 9 4 2 2 9 6 5 1 3
F
LED913,963, S913 3/REP
S909
GT560/GT560S
BTM
TEL
GT51W/GT510
LED914,964, S914 2/GP/ALBM+
S910
QQ
QQ
E
LED915,965, S915 1/GP/ALBM–
LED916,966, S916 DSPL
LED960
LED909 LED959
S914
LED912
S915
LED913 LED963
LED964
S916
LED914
S917
LED965
LED916 LED966
LED954
LED904 LED917 LED967
D
S904 LED904,954, S904 MODE
13942296513
13942296513
LED906,956, S906 EQ3
S903
LED993
S906
14
M>/ SEEK+
LED915
LED942
LED943
LED956 LED906
S907
13
LED903,953, S903
LED953
LED992
LED994
12
TEL
TEL
LED907,957, S907 .m/ SEEK–
11
R941
LED903
LED944
LED941–944, LED991–994 (VOLUME ILLUMINATE)
10
S902
R942
LED957 LED907
R940
B
LED908,958, S908 DSO
S908
LED902 LED952
LED958 LED908
LSW901
LED991 LED941
LED902,952, S902 SOURCE
LSW901 OFF
C
7
LED910
3
LED911 LED961
2
1
: Uses unleaded solder.
LED962
4-9. PRINTED WIRING BOARD — KEY SECTION —
CDX-GT51W/GT510/GT560/GT560S
Ref. No.
Location
Ref. No.
Location
Ref. No.
Location
LED954 LED956 LED957 LED958 LED959 LED960 LED961 LED962 LED963
D-5 D-2 C-2 B-2 D-12 D-11 D-10 D-9 D-9
LED964 LED965 LED966 LED967 LED991 LED992 LED993 LED994
D-8 D-7 D-6 D-4 B-3 C-4 D-4 C-3
Q941 Q942 Q991 Q992 Q993
G-5 G-9 G-7 H-7 H-8
x ia o y u 1 6 3
CDX-GT51W/GT510/GT560/GT560S
27 27 http://www.xiaoyu163.com
.
c o
m
(Page 25)
11 (11)
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 3 7 6 3 1 5 1 5 0
8 9 2 4 9 8 2 9 9
4-10. SCHEMATIC DIAGRAM — KEY SECTION —
D982
LED967
LED909
LED959
LED943
LED993
LED907
LSW901(2/2)
LED957
R993
FL900
Q993
R973 LED917
R992
Q992
Q991
R991
R972
R971 IC971
LED910
LED991
LED960
LED902
LED944
LED952
LED994
LED908
R933
LED958
C971
D971
LED966
LED941
R934
LED903
13942296513
13942296513
LED916
LED964
TEL
TEL
LED914
R988
LED953 R989
LED913
LED963
LED942
LED992
LED904
LED954
LED906
LED956 D931
LED915
LED911
LED965
R990
R966
LED961 R984 C932
LED912
R985 R986
LED962
R987 FB991 R925
TEL R924
R927
R926
R928
R929
R939
R930
R940
R947
R948
R955
1 3 9 4 2 2 9 6 5 1 3 R931
R932
R941
R942
R949
R950
R957
R956
R935
R936
R943
R944
R951
R952
R958
R937
R938
R945
R946
R953
R954
QQ
Q942
D983
R994
R995
8 9 2 4 9 8 2 9 9 R996
C991
C992
Q941
R963
R962
CN901
3 7 6 3 1 5 1 5 0
D984 UDZW-TE-17-18B
D981 UDZW-TE-17-18B
R981
J901
.
S904
RE901
FB971
x ia o y u 1 6 3
CDX-GT51W/GT510/GT560/GT560S
28 28 http://www.xiaoyu163.com
.
c o
R915
m
R916
S917
R914
S916
R913
S915
R912
S914
R911
S913
R910
S912
R909
S911
R959
R906
R907
R908
S908
S903
R905
S907
R904
S906
R903
S902
D988
UDZS-TE-17-6.8B
D992
UDZS-TE-17-6.8B
D990
UDZS-TE-17-6.8B
R902
S910
www
R901
S909
D993
D994
(Page 26)
UDZS-TE-17-6.8B
D989
UDZS-TE-17-6.8B
R983
LSW901(1/2)
R982
376315150 892498299
376315150 892498299
R923
R922
QQ
QQ
R921
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 • IC BLOCK DIAGRAMS
IC300 TDA8588AJ/N2/R1 (MAIN Board (1/3))
TAB 1 2 SDA LF– 3
I2C BUS 4 SCL
FL LF+ 5
6 VP2
RL
TEL
TEL
LR– 7 8 PGND3
LR+ 9 MUTE PROTECTION/ DIAGNOSTIC
IN_LF 15
12 IN_RR 14 IN_LR
MUTE
S-GND 13
10 SVR
13942296513
13942296513
IN-RL 11
16 ACGND
VP
RR+ 17
18 PGND2
RR RR– 19
20 VP1
CHIP DETECT/ DIAGNOSTIC
22 STB
QQ 376315150 892498299 24 PGND1
BATTERY DETECTION
DIAG 25
STANDBY/ MUTE
376315150 892498299
TEMPERATURE PROTECTION
ENABLE LOGIC
26 RST SW2 27
SWITCH
SW1 29
SWITCH
28 CRES 30 REG1 REGULATOR
376315150 892498299
TEL 13942296513
FR
RF– 23
QQ
QQ
RF+ 21
REG3 31 REG4 33
32 GND 34 REG5
VP 35
REFERENCE VOLTAGE REG2 37
www
.
REGULATOR
36 CBU LOADDUMP PROTECTION
BACK-UP SWITCH
xiaoy u163. com 29 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 IC401 BD3442FS-E2 (MAIN Board (2/3))
A1 1
VCC2
32 FIL
100k 31 GND A2 2 INPUT SELECTOR
100k B1 3
INPUT GAIN
VOLUME1 /MUTE
TREBLE /BASS /MIDDLE
VOLUME2 I2C BUS LOGIC
100k B2 4
30 SDA 29 SCL 28 MUTE
100k C1 5
VCC
27 VCC
100k C2 6
250k
FADER
25 OUTF2
250k
FADER
24 OUTR1
FADER
23 OUTR2
13942296513
DN 8
DP2 9 250k DS32 10 22 OUTS1
DS12 11 FADER DS22 12
LPF 21 OUTS2
EBIAS 13
FADER
13942296513
26 OUTF1
EFFECT
TEL
TEL
FADER
100k DP1 7
20 ADJ SPECTRUM ANALYZER
376315150 892498299
DS31 16
QQ
19 SOUT
376315150 892498299
IC601 BA8271F-E2 (MAIN Board (1/3))
BUS.ON 1
BUS ON SWITCH
RST 2
RESET SWITCH
BATT 3
BATTERY SWITCH
CLK 4 VREF 5 DATA I/O 6
www
14 VCC
13 12 11 10
RST BUS.IN CLK-IN B/U-C
9 DATA IN
GND 7
xiaoy u163. com 8 DATA OUT
.
30 http://www.xiaoyu163.com
18 DATA 17 CLK
376315150 892498299
TEL 13942296513 DS11 15
QQ
QQ
DS21 14
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 • IC PIN DESCRIPTIONS
• IC501 MB90F045PF-G-9016-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) Pin No.
Pin Name
I/O
Pin Description
1
AREASEL0
I
Destination setting pin
2
AREASEL1
I
Destination setting pin
3
AREASEL2
I
Frequency select signal input
4
B-OUTSEL
I
Blackout existence distinction signal input (L: blackout none, H: blackout)
5
NOSE_SW
I
Front panel detaching detection signal input (L: Panel on, H: Panel off)
6
ACC_SEL
I
ACC distinction signal input (Pull up)
7
BEEP
O
BEEP signal output
8
DIAG
I
Status signal input from power amplifier.
VOLATT
O
Electronic volume attenuate control signal output.
FSW_IN
O
DC/DC converter frequency signal input
TEL
11
VSS
—
Ground
12
TUATT
O
Tuner mute control signal output
13942296513
13
NSMASK
O
Noise mask signal output
14
NCO
I
Not used. (Open)
15
ILLUMI_SEL
I
Illumination voltage setting pin (L: 9V, H: 10.4V)
16
NCO
O
Not used. (Open)
17
AUX_SW
O
Not used. (Open) FL driver chip select signal output
O
FL driver serial data signal output
20
FL_SCK
O
FL driver serial clock signal output
21
USB_OVL
O
Not used. (Open)
22
USB_ON
O
Not used. (Open)
23
VCC5
—
Power supply (+3.3V)
24
EEP_SIO
I/O
EEPROM bus serial data input/output
25
EEP_CKO
O
EEPROM bus serial clock output
26
AMPSTB
O
Power AMP standby signal output
27
MC-RX
O
Not used. (Open)
28
MC-TX
O
Not used. (Open)
29
NCO
O
Not used. (Open)
30
RDS ON
O
RDS ON signal output
31
NCO
O
Not used. (Open)
32
SA_DATA
O
Spectrum analyzer data signal output
33
I2C_CKO
O
I2C bus serial clock signal output
34
I2C_SIO
I/O
I2C bus serial data signal input/output
35
DAVDD
—
A/D converter power supply (+3.3V)
36
AVRH
—
A/D converter external reference power supply (+3.3V)
37
DAVSS
—
A/D converter Ground
38
QUALITY
I
Noise detect signal input
39
VSM
I
S-meter voltage detect signal input
40
KEYIN1
I
Key signal input 1
41
KEYIN0
I
Key signal input 0
42
VSS
—
www
RC_IN0
43
QQ 376315150 892498299
Not used in this set. (Open)
Ground
xiaoy u163. com I
Rotary commander key signal input
44
SA_IN
I
Spectrum analyzer signal input
45
SA_CKO
O
Spectrum analyzer clock signal output
DOOR_IND
O
DISC IN/EJECT indicator LED control signal output
RE-IN0
I
Rotary encoder signal input 0
RE-IN1
I
Rotary encoder signal input 1
46 47 48
.
376315150 892498299
376315150 892498299
O
FL_SO
QQ
QQ
FL_CS
19
13942296513
Not used in this set. (Open)
18
TEL 13942296513
TEL
9 10
31 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 Pin Name
I/O
49
MD0
I
Operation mode setting pin (Pull up)
Pin Description
50
MD1
I
Operation mode setting pin (Pull up)
51
MD2
I
Operation mode setting pin (Pull down)
52
KEYACK
I
Key acknowledgment detect signal input
53
TU_ATTIN
I
Tuner mute zero cross detect signal input
54
BUIN
I
Back-up power supply detect signal input
55
NCO
O
Not used. (Open)
56
DAVN
I
RDS data block synchronized detect signal input
57
NCO
O
Not used. (Open)
58
UNISI
I
S-BUS data signal input
59
UNISO
O
S-BUS data signal output
60
UNISCK
O
S-BUS clock signal output
61 to 63
NCO
O
Not used. (Open)
Not used in this set. (Pull down) Not used in this set. (Pull down)
Not used in this set. (Pull down)
TEL
TEL
Pin No.
Remote control signal input FL12V Regulator ON/OFF control signal output
66
FSW_OUT
O
DC/DC converter frequency shift control signal output
67
DD_ON
O
FL3.3V Regulator control signal output
68
FLASH_W
I
Memory mode select signal input
69
NCO
O
Not used. (Open)
70
DOOR_SW
I
Panel open/close detect signal input
RC_IN1
I
Rotary commander key signal input
72
ACC_IN
I
Accessory power supply detect signal input
376315150 892498299
TESTIN
I
Test mode detect signal input
74
TELATT
I
Telephone attenuate detect signal input
75
ILLUIN
I
Illumination detect signal input
76
AD_ON
O
A/D converter power supply control signal output
77
RESET
I
System reset signal input
78
NCO
O
Not used. (Open)
79
XOUT
O
Sub clock signal output (32.768kHz)
80
XIN
I
81
VSS1
—
Sub clock signal input (32.768kHz)
82
OSCIN
I
83
OSCOUT
O
Main clock signal output (18.432kHz)
84
VCC3
—
Power supply (+3.3 V)
85
NCO
O
Not used. (Open)
86
ATT
O
Audio mute control signal output
Ground Main clock signal input (18.432kHz)
87
BUSON
O
BUS ON signal output
88
SYSRST
O
System reset signal output
89
EJECT_OK_SW
O
EJECT OK signal output
90
NCO
O
Not used. (Open)
91
WAKEUP
O
Not used. (Open)
92
NCO
O
Not used. (Open)
93
Z-MUTE
I
CD zero cross mute detect signal input
NCO
O
Not used. (Open)
I
DEMO mode setting input (H: DEMO ON, L: DEMO OFF)
I
Cyril select signal input (H: CYRIL, L: Non-CYRIL)
O
Not used. (Open)
I
CD mechanism servo power control request signal input
I
CD mechanism deck power control request signal input
O
Mute signal output at during the AUX source mode (H: Keep, L: Other)
94
www
95
DEMO_SEL
96
CYRIL_SEL
97
NCO
98
CD_ON
.
99
CDM_ON
100
OPEN_MUTE
xiaoy u163. com
32 http://www.xiaoyu163.com
376315150 892498299
QQ 376315150 892498299
TEL 13942296513
73
QQ
71
Not used in this set. (Pull up)
13942296513
I O
65
QQ
SIRCS FL12V_ON
13942296513
64
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S SECTION 5 EXPLODED VIEWS
QQ 376315150 892498299 NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Abbreviation CND : Canadian model EA : Saudi Arabia model MX : Mexican model
5-1.
•
•
•
The components identified by mark 0 or dotted line with mark. 0 are critical for safety. Replace only with part number specified.
-XX and -X mean standardized parts, so they may have some difference from the original one. Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color Accessories are given in the last of this parts list.
MAIN SECTION
not supplied
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
A
#2
MG-101FA-188//Q
TEL
TEL
12 #3
#1
#4
13942296513
13942296513
#5
B
FU601
A
#4 #5
9
not supplied
#3
#5
10
QQ
QQ
not supplied
8
7
QQ 376315150 892498299 #1
TU1
376315150 892498299
376315150 892498299
TEL 13942296513
11
not supplied
not supplied
not supplied
B
6
#1
2
5
1 #1
not supplied (SUB board)
5
Ref. No. 1 2 3 4 5
Part No.
Description
X-3384-259-1 3-246-441-01 1-833-591-11 3-260-247-01 3-042-244-01
LOCK ASSY BUTTON (EJECT) CABLE, FLEXIBLE FLAT (20 CORE) CUSHION (SUB PANEL) SCREW (T)
www
Remark
Ref. No. 10 11 12 FU601 TU1
Part No.
Description
A-1206-183-A 2-021-848-01 1-833-102-11 1-532-877-11 A-3220-961-B
MAIN BOARD, COMPLETE (GT560:EA) SHEET (TU), GROUND CORD (WITH CONNECTOR) (POWER) FUSE (BLADE TYPE) (AUTO FUSE) 10A TUNER UNIT (TUX-032)
Remark
xiaoy u163. com
6 7 8 9 10
X-2149-195-1 X-3384-203-1 3-713-786-51 3-376-464-11 A-1204-625-A
10
A-1206-171-A MAIN BOARD, COMPLETE (GT560:E,MX/GT560S)
.
3
4
PANEL ASSY, SUB GEAR ASSY SCREW +P 2X3 SCREW (+PTT 2.6X6), GROUND POINT MAIN BOARD, COMPLETE (GT51W/GT510)
#1 #2 #3 #4 #5
7-685-792-09 7-685-790-01 7-685-793-09 7-685-134-19 7-685-794-09
SCREW +PTT 2.6X6 (S) SCREW +PTT 2.6X4 (S) SCREW +PTT 2.6X8 (S) SCREW +P 2.6X8 TYPE2 NON-SLIT SCREW +PTT 2.6X10 (S)
33 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299
5-2.
FRONT PANEL SECTION
57 56 RE901
TEL
TEL
57 58
13942296513
13942296513
not supplied (KEY board) J901 FL901
not supplied
not supplied
not supplied
not supplied
52
not supplied
53
55
Ref. No. 51 51 51 51 51 51 52 53 53 54
54
51
Part No.
Description
A-1204-628-A A-1206-157-A A-1206-173-A A-1206-177-A A-1206-527-A
PANEL OVERALL ASSY, FRONT (GT510:US) PANEL OVERALL ASSY, FRONT (GT51W:US) PANEL OVERALL ASSY, FRONT (GT560S) PANEL OVERALL ASSY, FRONT (GT560) PANEL OVERALL ASSY, FRONT (GT51W:CND)
www A-1206-528-A 3-264-712-01 X-2149-200-1 X-2149-332-1 X-2149-199-1
Remark
Part No.
Description
54 54 54 55 56
X-2149-328-1 X-2149-331-1 X-2149-333-1 X-2149-198-1 X-2149-196-1
PANEL (SV) ASSY, FRONT (GT51W) PANEL (SV) ASSY, FRONT (GT560S) PANEL (SV) ASSY, FRONT (GT560) KNOB ASSY (S) PANEL ASSY, BACK
57 58 FL900 J901 RE901
3-250-543-21 X-2149-228-1 1-519-916-11 1-820-833-11 1-479-902-11
SCREW (+B P-TITE M2) CASE ASSY (for FRONT PANEL) (EXCEPT US) INDICATOR TUBE, FLUORESCENT JACK (SMALL TYPE) (VERTICAL) (AUX) ENCODER, ROTARY (PUSH SELECT (VOLUME))
xiaoy u163. com
PANEL OVERALL ASSY, FRONT (GT510:CND) SPRING (OPEN) BUTTON ASSY (S) (GT51W/GT510/GT560) BUTTON ASSY (S) (GT560S) PANEL (SV) ASSY, FRONT (GT510)
.
Ref. No.
34 http://www.xiaoyu163.com
Remark
376315150 892498299
376315150 892498299
QQ 376315150 892498299
not supplied
QQ
QQ
TEL 13942296513
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S Ver. 1.2
QQ 376315150 892498299 5-3.
CD MECHANISM SECTION (MG-101FA-188//Q)
NOTE: Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.
101 102 not supplied
TEL
TEL
not supplied
103
#6
#6
13942296513
13942296513
105
not supplied not supplied
not supplied
not supplied not supplied
QQ
QQ
376315150 892498299 not supplied
376315150 892498299
376315150 892498299
QQ
TEL 13942296513
104
not supplied
not supplied not supplied
107
106 106
www Ref. No.
Part No.
101 102 0 103 104
A-1177-168-A A-1177-169-A X-2149-672-1 2-626-869-01
.
xiaoy u163. com Description
Remark
MECHANICAL BLOCK ASSY DAXEV//Q SERVICE ASSY, OP (DAX-25A) SCREW (M2X3), SERRATION
Ref. No. 105 106 107 #6
Part No.
Description
3-348-998-31 3-352-758-31 A-1177-362-A 7-627-000-08
SCREW (M1.4X2.5), TAPPING, PAN SCREW (M1.7X2.5), TOOTHED LOCK SERVO BOARD, COMPLETE SCREW, PRECISION +P 1.7X2.2 TYPE3
Remark
35 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S SECTION 6 KEY ELECTRICAL PARTS LIST
QQ 376315150 892498299
NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • Abbreviation CND : Canadian model EA : Saudi Arabia model MX : Mexican model Ref. No.
Part No.
•
•
• •
Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. CAPACITORS uF : µF COILS uH : µH
Description
Remark
1uF 0.1uF 0.1uF 0.1uF
10% 10% 10% 10%
6.3V 16V 16V 16V
< CONNECTOR > CN901
1-818-141-11 PLUG, CONNECTOR 20P
D984 D988 D989 D990 D992
6-501-180-01 8-719-978-33 8-719-978-33 8-719-978-33 8-719-978-33
DIODE DIODE DIODE DIODE DIODE
UDZW-TE-17-18B DTZS-TT11-6.8B DTZS-TT11-6.8B DTZS-TT11-6.8B DTZS-TT11-6.8B
D993 D994
8-719-420-90 DIODE MA8051-M 8-719-978-33 DIODE DTZS-TT11-6.8B
1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP
0 0
1-519-916-11 INDICATOR TUBE, FLUORESCENT
8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09
LED LED LED LED LED
SML-310VTT86 (5) SML-310VTT86 (4/SHUF) SML-310VTT86 (3/REP) SML-310VTT86 (2/GP/ALBM +) SML-310VTT86 (1/GP/ALBM –)
8-719-053-09 8-719-053-09 8-719-078-21 6-501-642-01
LED LED LED LED
LED958 6-501-642-01 LED SML-512PWT86A (DSO) (GT51W/GT510/GT560) LED958 8-719-078-21 LED SML-310PTT86 (DSO) (GT560S) LED959 8-719-078-21 LED SML-310PTT86 (SCRL) LED960 8-719-078-21 LED SML-310PTT86 (6/PAUSE) LED961 8-719-078-21 LED SML-310PTT86 (5)
6-600-163-01 IC RS-770 (IR) < JACK >
www
J901
LED911 LED912 LED913 LED914 LED915
LED954 8-719-078-21 LED SML-310PTT86 (MODE) LED956 6-501-642-01 LED SML-512PWT86A (EQ3) (GT51W/GT510/GT560) LED956 8-719-078-21 LED SML-310PTT86 (EQ3) (GT560S) LED957 6-501-642-01 LED SML-512PWT86A (. m/SEEK–) (GT51W/GT510/GT560) LED957 8-719-078-21 LED SML-310PTT86 (. m/SEEK–) (GT560S)
< IC > IC971
SML-310VTT86 (EQ3) SML-310VTT86 (. m/SEEK–) SML-310VTT86 (DSO) SML-310VTT86 (SCRL) SML-310VTT86 (6/PAUSE)
SML-310VTT86 (VOLUME ILLUMINATE) SML-310VTT86 (VOLUME ILLUMINATE) SML-310PTT86 (SOURCE) SML-512PWT86A (M >/SEEK+) (GT51W/GT510/GT560) LED953 8-719-078-21 LED SML-310PTT86 (M >/SEEK+) (GT560S)
< FLUORESCENT INDICATOR TUBE > FL900
LED LED LED LED LED
LED943 LED944 LED952 LED953
< JUMPER RESISTOR > FB971 FB991
8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09 8-719-053-09
.
8-719-078-21 8-719-078-21 8-719-078-21 8-719-078-21 8-719-078-21
LED LED LED LED LED
SML-310PTT86 (4/SHUF) SML-310PTT86 (3/REP) SML-310PTT86 (2/GP/ALBM +) SML-310PTT86 (1/GP/ALBM –) SML-310PTT86 (DSPL)
xiaoy u163. com
1-820-833-11 JACK (SMALL TYPE) (VERTICAL) (AUX) < DIODE >
LED962 LED963 LED964 LED965 LED966
LED902 8-719-053-09 LED SML-310VTT86 (SOURCE) LED903 8-719-053-09 LED SML-310VTT86 (M >/SEEK+) LED904 8-719-053-09 LED SML-310VTT86 (MODE)
LED967 8-719-078-21 LED SML-310PTT86 (BTM/CAT) (GT51W/GT510) LED967 8-719-078-21 LED SML-310PTT86 (BTM) (GT560/GT560S) LED991 8-719-078-21 LED SML-310PTT86 (VOLUME ILLUMINATE)
36 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1SS355TE-17 MA8051-M UDZW-TE-17-18B RF101L2STE25 MA8051-M
LED906 LED907 LED908 LED909 LED910
QQ
QQ
DIODE DIODE DIODE DIODE DIODE
Remark
QQ 376315150 892498299
TEL 13942296513 8-719-988-61 8-719-420-90 6-501-180-01 6-501-089-01 8-719-420-90
Description
LED916 8-719-053-09 LED SML-310VTT86 (DSPL) LED917 8-719-053-09 LED SML-310VTT86 (BTM/CAT) (GT51W/GT510) LED917 8-719-053-09 LED SML-310VTT86 (BTM) (GT560/GT560S) LED941 8-719-053-09 LED SML-310VTT86 (VOLUME ILLUMINATE) LED942 8-719-053-09 LED SML-310VTT86 (VOLUME ILLUMINATE)
< DIODE >
D931 D971 D981 D982 D983
Part No.
13942296513
13942296513
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
Ref. No.
TEL
TEL
< CAPACITOR > 1-125-837-11 1-107-826-11 1-107-826-11 1-107-826-11
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. When indicating parts by reference number, please include the board.
KEY BOARD **********
C932 C971 C991 C992
The components identified by mark 0 or dotted line with mark. 0 are critical for safety. Replace only with part number specified.
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 KEY
Ref. No.
Part No.
Description
Part No.
Description
R948 R949 R950 R951 R952
1-216-030-00 1-216-031-00 1-216-027-00 1-216-029-00 1-216-030-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
160 180 120 150 160
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R953 R954 R955 R956 R957
1-216-031-00 1-216-027-00 1-216-029-00 1-216-030-00 1-216-031-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
180 120 150 160 180
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R958 R959 R962 R963 R966
1-216-027-00 1-216-047-11 1-216-864-11 1-216-864-11 1-216-833-11
RES-CHIP RES-CHIP SHORT CHIP SHORT CHIP METAL CHIP
120 820 0 0 10K
5% 5%
1/10W 1/10W
5%
1/10W
5% 5% 5%
1/10W 1/10W 1/10W
< SWITCH > LSW901 1-798-017-11 SWITCH, TACTILE (WITH LED) (OFF) < TRANSISTOR > Q941 Q942 Q991 Q992 Q993
6-550-752-01 6-550-752-01 8-729-026-49 8-729-026-49 8-729-026-49
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
DTC614TKT146 DTC614TKT146 2SA1037AK-T146-R 2SA1037AK-T146-R 2SA1037AK-T146-R
TEL
< RESISTOR >
Remark
13942296513
RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
820 1K 1K 1.2K 1.5K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R971 R972 R973 R981 R982
1-216-811-11 1-216-809-11 1-216-811-11 1-216-864-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP SHORT CHIP SHORT CHIP
150 100 150 0 0
R906 R907 R908 R909 R910
1-216-824-11 1-216-825-11 1-216-827-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1.8K 2.2K 3.3K 1K 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R983 R984 R985 R986 R987
1-216-864-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-845-11
SHORT CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 100 100 100 100K
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
R911 R912 R913 R914 R915
1-216-822-11 1-216-823-11 1-216-824-11 1-216-825-11 1-216-827-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1.2K 1.5K 1.8K 2.2K 3.3K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R988 R989 R990 R991 R992
1-216-821-11 1-216-821-11 1-216-821-11 1-216-833-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 1K 10K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R916 R921 R922 R923 R924
1-216-828-11 1-216-027-00 1-216-023-00 1-216-025-11 1-216-021-00
METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
3.9K 120 82 100 68
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R993 R994 R995 R996
1-216-833-11 1-216-845-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 100K 100K 100K
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
R925 R926 R927 R928 R929
1-216-027-00 1-216-023-00 1-216-025-11 1-216-021-00 1-216-027-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
120 82 100 68 120
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R930 R931 R932 R933 R934
1-216-023-00 1-216-025-11 1-216-021-00 1-216-033-00 1-216-029-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
82 100 68 220 150
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R935 R936 R937 R938 R939
1-216-027-00 1-216-027-00 1-216-025-11 1-216-027-00 1-216-029-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
120 120 100 120 150
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R940 R941 R942 R943 R944
1-216-030-00 1-216-031-00 1-216-027-00 1-216-029-00 1-216-030-00
RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP
160 180 120 150 160
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R945 R946 R947
1-216-031-00 RES-CHIP 1-216-027-00 RES-CHIP 1-216-029-00 RES-CHIP
180 120 150
5% 5% 5%
1/10W 1/10W 1/10W
TEL 13942296513
QQ 376315150 892498299 < ROTARY ENCODER >
www
.
RE901
1-479-902-11 ENCODER, ROTARY (PUSH SELECT (VOLUME)) < SWITCH >
S902 S903 S904 S906 S907
1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21
SWITCH, TACTILE (SOURCE) SWITCH, TACTILE (M >/SEEK+) SWITCH, TACTILE (MODE) SWITCH, TACTILE (EQ3) SWITCH, TACTILE (. m/SEEK–)
S908 S909 S910 S911 S912
1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21
SWITCH, TACTILE (DSO) SWITCH, TACTILE (SCRL) SWITCH, TACTILE (6/PAUSE) SWITCH, TACTILE (5) SWITCH, TACTILE (4/SHUF)
S913 S914 S915 S916 S917
1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21 1-786-653-21
SWITCH, TACTILE (3/REP) SWITCH, TACTILE (2/GP/ALBM +) SWITCH, TACTILE (1/GP/ALBM –) SWITCH, TACTILE (DSPL) SWITCH, TACTILE (BTM/CAT) (GT51W/GT510)
xiaoy u163. com
S917 1-786-653-21 SWITCH, TACTILE (BTM) (GT560/GT560S) *************************************************************
37 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
1-216-047-11 1-216-821-11 1-216-821-11 1-216-822-11 1-216-823-11
QQ
QQ
R901 R902 R903 R904 R905
13942296513
Ref. No.
TEL
Remark
LED992 8-719-078-21 LED SML-310PTT86 (VOLUME ILLUMINATE) LED993 8-719-078-21 LED SML-310PTT86 (VOLUME ILLUMINATE) LED994 8-719-078-21 LED SML-310PTT86 (VOLUME ILLUMINATE)
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 MAIN
Ref. No.
Part No.
Description
Remark
A-1204-625-A MAIN BOARD, COMPLETE (GT51W/GT510) A-1206-171-A MAIN BOARD, COMPLETE (GT560:E,MX/GT560S) A-1206-183-A MAIN BOARD, COMPLETE (GT560:EA) ********************* 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-794-09 SCREW +PTT 2.6X10 (S) < CAPACITOR > 20% 10% 10% 20% 10%
35V 25V 16V 35V 25V
C8 C9 C14 C103 C104
1-162-967-11 1-162-970-11 1-162-964-11 1-165-319-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0033uF 0.01uF 0.001uF 0.1uF 0.1uF
10% 10% 10% 10%
50V 25V 50V 50V 16V
C108 C109 C110 C114 C116
1-162-970-11 1-162-970-11 1-162-970-11 1-162-970-11 1-162-968-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.01uF 0.01uF 0.01uF 0.0047uF
10% 10% 10% 10% 10%
25V 25V 25V 25V 50V
C117 C300 C301 C303 C304
1-162-968-11 1-126-960-11 1-115-340-11 1-128-551-11 1-115-340-11
CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP
0.0047uF 1uF 0.22uF 22uF 0.22uF
10% 20% 10% 20% 10%
50V 50V 25V 63V 25V
C305 C306 C307 C308 C309
1-107-826-11 1-126-964-11 1-107-826-11 1-126-964-11 1-115-340-11
CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP
0.1uF 10uF 0.1uF 10uF 0.22uF
10% 20% 10% 20% 10%
16V 50V 16V 50V 25V
C310 C312 C313 C314 C315
1-126-916-11 1-115-340-11 1-107-826-11 1-124-261-00 1-107-826-11
ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
1000uF 0.22uF 0.1uF 10uF 0.1uF
20% 10% 10% 20% 10%
6.3V 25V 16V 50V 16V
C316 C317 C318 C319 C320
1-124-261-00 1-124-257-00 1-162-923-11 1-127-715-11 1-125-891-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
10uF 2.2uF 47PF 0.22uF 0.47uF
20% 20% 5% 10% 10%
50V 50V 50V 16V 10V
C321 C323 C324 C325 C327
1-126-960-11 1-115-340-11 1-115-340-11 1-107-826-11 1-127-715-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
1uF 0.22uF 0.22uF 0.1uF 0.22uF
20% 10% 10% 10% 10%
50V 25V 25V 16V 16V
C328 C330 C331 C360 C361
1-127-715-11 1-216-864-11 1-216-864-11 1-165-908-11 1-165-908-11
CERAMIC CHIP SHORT CHIP SHORT CHIP CERAMIC CHIP CERAMIC CHIP
0.22uF 0 0 1uF 1uF
10%
16V
10% 10%
10V 10V
C362 C363 C364 C401 C402
1-165-908-11 1-115-871-11 1-115-871-11 1-124-584-00 1-162-970-11
CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP
1uF 1uF 1uF 100uF 0.01uF
10% 20% 20% 20% 10%
10V 50V 50V 10V 25V
TEL 13942296513
www
.
220uF 22uF 100PF 0.01uF 100PF
20% 20% 5% 10% 5%
10V 25V 50V 25V 50V
Remark
C414 C415 C417 C418 C419
1-163-251-11 1-162-970-11 1-162-970-11 1-162-966-11 1-162-966-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF 0.01uF 0.01uF 0.0022uF 0.0022uF
5% 10% 10% 10% 10%
50V 25V 25V 50V 50V
C421 C422 C423 C431 C432
1-126-791-11 1-163-251-11 1-165-908-11 1-126-791-11 1-163-251-11
ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
10uF 100PF 1uF 10uF 100PF
20% 5% 10% 20% 5%
35V 50V 10V 35V 50V
C441 C442 C443 C446 C447
1-126-791-11 1-163-251-11 1-165-908-11 1-165-908-11 1-165-908-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
10uF 100PF 1uF 1uF 1uF
20% 5% 10% 10% 10%
35V 50V 10V 10V 10V
C451 C452 C461 C462 C465
1-126-791-11 1-163-251-11 1-126-791-11 1-165-908-11 1-165-908-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP
10uF 100PF 10uF 1uF 1uF
20% 5% 20% 10% 10%
35V 50V 35V 10V 10V
C466 C471 C472 C480 C481
1-165-908-11 1-126-791-11 1-165-908-11 1-136-159-00 1-136-159-00
CERAMIC CHIP ELECT CERAMIC CHIP FILM FILM
1uF 10uF 1uF 0.033uF 0.033uF
10% 20% 10% 5% 5%
10V 35V 10V 50V 50V
C482 C483 C484 C485 C487
1-162-968-11 1-162-968-11 1-107-826-11 1-104-665-11 1-126-791-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT
0.0047uF 0.0047uF 0.1uF 100uF 10uF
10% 10% 10% 20% 20%
50V 50V 16V 25V 35V
C491 C501 C502 C503 C504
1-124-589-11 1-128-057-11 1-162-970-11 1-124-584-00 1-162-970-11
ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP
47uF 330uF 0.01uF 100uF 0.01uF
20% 20% 10% 20% 10%
16V 6.3V 25V 10V 25V
C505 C506 C507 C508 C509
1-124-584-00 1-162-970-11 1-162-970-11 1-162-964-11 1-162-970-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100uF 0.01uF 0.01uF 0.001uF 0.01uF
20% 10% 10% 10% 10%
10V 25V 25V 50V 25V
C510 C511 C512 C513 C515
1-162-964-11 1-162-964-11 1-162-964-11 1-162-964-11 1-162-917-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 0.001uF 0.001uF 0.001uF 15PF
10% 10% 10% 10% 5%
50V 50V 50V 50V 50V
C516 C519 C523 C600 C601
1-162-918-11 1-107-826-11 1-162-927-11 1-126-935-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
18PF 0.1uF 100PF 470uF 0.01uF
5% 10% 5% 20% 10%
50V 16V 50V 16V 25V
C602 C701 C702
1-165-319-11 CERAMIC CHIP 1-131-868-81 ELECT 1-126-160-11 ELECT
0.1uF 3300uF 1uF
20% 20%
50V 16V 50V
QQ 376315150 892498299
xiaoy u163. com
38 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
47uF 0.01uF 0.1uF 47uF 0.01uF
ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
QQ
QQ
ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
Description
1-126-176-11 1-124-248-00 1-162-927-11 1-162-970-11 1-163-251-11
13942296513
13942296513
1-126-947-11 1-162-970-11 1-107-826-11 1-126-947-11 1-162-970-11
Part No.
C403 C405 C410 C412 C413
TEL
TEL
C2 C3 C4 C5 C7
Ref. No.
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 MAIN
Ref. No.
Part No.
Description
ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT
4.7uF 0.22uF 0.01uF 100uF 220uF
20% 10% 10% 20% 20%
50V 25V 25V 25V 16V
Remark
D365 D366 D367 D400 D491
8-719-977-12 8-719-977-12 8-719-977-12 6-501-013-01 8-719-404-50
DIODE DIODE DIODE DIODE DIODE
DTZ6.8B DTZ6.8B DTZ6.8B BAT54ALT1G MA111-TX
C804 C805 C809 C810 C811
1-126-963-11 1-126-933-11 1-107-826-11 1-107-826-11 1-107-826-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
4.7uF 100uF 0.1uF 0.1uF 0.1uF
20% 20% 10% 10% 10%
50V 16V 16V 16V 16V
D493 D494 D501 D502 D511
6-501-051-01 6-501-013-01 8-719-050-37 8-719-060-48 6-501-051-01
DIODE DIODE DIODE DIODE DIODE
BAT54CLT1G BAT54ALT1G M1MA152WA-T1 RB751V-40TE-17 BAT54CLT1G
C812 C813 C814 C816 C817
1-107-826-11 1-162-927-11 1-107-826-11 1-162-970-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 100PF 0.1uF 0.01uF 0.01uF
10% 5% 10% 10% 10%
16V 50V 16V 25V 25V
D602 D603 D604 D605 D606
8-719-057-80 8-719-422-67 8-719-057-80 8-719-057-80 8-719-072-70
DIODE DIODE DIODE DIODE DIODE
MA8180-M-TX MA8062-H MA8180-M-TX MA8180-M-TX MA2ZD14001S0
C819 C821 C830 C901 C902
1-107-826-11 1-107-826-11 1-162-964-11 1-163-009-11 1-163-009-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.001uF 0.001uF 0.001uF
10% 10% 10% 10% 10%
16V 16V 50V 50V 50V
D607 D701 D702 D703 D704
6-501-571-01 8-719-057-80 8-719-057-80 8-719-420-90 8-719-057-80
DIODE DIODE DIODE DIODE DIODE
1N5404-C311-3 MA8180-M-TX MA8180-M-TX MA8051-M MA8180-M-TX
C997 C998
1-162-964-11 CERAMIC CHIP 1-216-864-11 SHORT CHIP
0.001uF 0
10%
50V
D705 D801 D802 D903
8-719-404-50 6-501-124-01 8-719-420-90 8-719-057-80
DIODE DIODE DIODE DIODE
MA111-TX RSX101VA-30TR MA8051-M MA8180-M-TX
< CONNECTOR > 1-774-701-21 1-820-611-11 1-569-913-11 1-580-907-41
PIN, CONNECTOR 16P CONNECTOR, BOARD TO BOARD 28P SOCKET, CONNECTOR 20P PLUG, CONNECTOR 8P (BUS CONTROL IN)
Remark
< JUMPER RESISTOR > 1-216-295-11 1-216-864-11 1-216-864-11 1-216-295-11 1-216-864-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
FB406 FB407 FB408 FB801 FB802
1-216-864-11 1-216-295-11 1-216-864-11 1-216-864-11 1-216-864-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
FB803 FB804
1-216-864-11 SHORT CHIP 1-216-821-11 METAL CHIP
QQ 376315150 892498299
TEL 13942296513 < DIODE >
D2 D101 D102 D103 D104
8-719-977-03 8-719-977-12 8-719-420-90 8-719-057-80 8-719-057-80
DIODE DIODE DIODE DIODE DIODE
DTZ5.6B DTZ6.8B MA8051-M MA8180-M-TX MA8180-M-TX
D105 D106 D107 D108 D109
8-719-420-90 8-719-420-90 8-719-420-90 8-719-420-90 8-719-420-90
DIODE DIODE DIODE DIODE DIODE
MA8051-M MA8051-M MA8051-M MA8051-M MA8051-M
D110 D114 D115 D116 D119
8-719-420-90 8-719-420-90 8-719-978-33 8-719-977-12 8-719-057-80
DIODE DIODE DIODE DIODE DIODE
MA8051-M MA8051-M DTZS-TT11-6.8B DTZ6.8B MA8180-M-TX
IC300 IC401 IC501 IC502 IC601
6-705-359-02 6-710-065-01 6-806-959-01 6-704-529-01 6-703-884-01
D120 D301 D302 D303 D304
8-719-420-90 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01
DIODE DIODE DIODE DIODE DIODE
MA8051-M 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2
IC602 IC801 IC802
6-703-224-01 IC S-80828CNNB-B8NT2G 6-710-493-01 IC NJM2370U1-12-TE2 6-707-911-01 IC BD9778HFP
D305 D306 D307 D308 D309
6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01 6-500-522-01
DIODE DIODE DIODE DIODE DIODE
10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2 10EDB40-TA1B2
J1 J370 J451
D310 D311 D312
6-500-522-01 DIODE 10EDB40-TA1B2 6-500-522-01 DIODE 10EDB40-TA1B2 6-500-522-01 DIODE 10EDB40-TA1B2
www
0 1K
5%
1/10W
< IC > IC IC IC IC IC
TDA8588AJ/N2/R1 BD3442FS-E2 MB90F045PF-G-9016-SPE1 XC6206P332PR BA8271F-E2
< JACK > 1-815-185-13 JACK (ANTENNA) 1-566-822-41 JACK (REMOTE IN) 1-774-700-41 JACK, PIN 6P (BUS AUDIO IN, AUDIO OUT REAR/FRONT)
xiaoy u163. com
< JUMPER RESISTOR >
.
JC3 JC32
1-216-864-11 SHORT CHIP 1-216-864-11 SHORT CHIP
0 0
39 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
FB401 FB402 FB403 FB404 FB405
QQ
QQ
CN300 CN350 CN802 CNJ400
Ref. No.
13942296513
13942296513
Description
1-126-163-11 1-115-340-11 1-162-970-11 1-104-665-11 1-126-934-11
TEL
TEL
Part No.
C703 C704 C705 C801 C802
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 MAIN
Ref. No.
Remark
Q590 Q600 Q601 Q605 Q701
8-729-027-23 8-729-047-76 8-729-027-23 8-729-027-43 8-729-120-28
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
JC303 JC350 JC400 JC401 JC430
1-216-864-11 1-216-296-11 1-216-295-11 1-216-864-11 1-216-296-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
Q702 Q703 Q801
8-729-120-28 TRANSISTOR 2SC1623-L5L6 8-729-120-28 TRANSISTOR 2SC1623-L5L6 1-801-806-11 TRANSISTOR DTC144EKA
JC490 JC491 JC501 JC503 JC504
1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
R2 R3 R4 R5 R6
1-216-839-11 1-216-843-11 1-216-839-11 1-216-843-11 1-414-595-11
METAL CHIP 33K METAL CHIP 68K METAL CHIP 33K METAL CHIP 68K INDUCTOR, FERRITE BEAD
JC508 JC511 JC512 JC514 JC515
1-216-296-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
R7 R10 R12 R13 R301
1-414-595-11 1-216-821-11 1-414-595-11 1-414-595-11 1-216-811-11
INDUCTOR, FERRITE BEAD METAL CHIP 1K INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD METAL CHIP 150
JC516 JC518 JC519 JC522 JC523
1-216-864-11 1-216-296-11 1-216-296-11 1-216-295-11 1-216-295-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
R302 R351 R355 R356 R357
1-216-841-11 1-216-845-11 1-216-834-11 1-216-834-11 1-216-817-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
JC524 JC600 JC602 JC603 JC800
1-216-296-11 1-216-864-11 1-216-296-11 1-216-296-11 1-216-296-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0
R358 R359 R361 R370 R371
1-216-817-11 1-216-864-11 1-216-821-11 1-216-809-11 1-216-809-11
Remark
JC804 JC998 JC999
1-216-295-11 SHORT CHIP 1-162-964-11 CERAMIC CHIP 1-216-864-11 SHORT CHIP < COIL >
R400 R401 R402 R407 R416
DTA114EKA-T146 FMC2A-T148 DTA114EKA-T146 DTC114EKA-T146 2SC1623-L5L6
< RESISTOR > 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
5%
1/10W
5%
1/10W
47K 100K 12K 12K 470
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP
470 0 1K 100 100
5%
1/10W
1-216-296-11 1-216-821-11 1-216-821-11 1-216-864-11 1-216-821-11
SHORT CHIP METAL CHIP METAL CHIP SHORT CHIP METAL CHIP
0 1K 1K 0 1K
QQ 376315150 892498299
TEL 13942296513 0 0.001uF 0
Ref. No.
10%
50V
5% 5% 5%
1/10W 1/10W 1/10W
5% 5%
1/10W 1/10W
5%
1/10W
L1 L4 L101 L300 L301
1-500-245-11 1-469-844-11 1-410-509-11 1-456-617-11 1-216-864-11
INDUCTOR, FERRITE BEAD INDUCTOR 2.2uH INDUCTOR 10uH COIL, CHOKE SHORT CHIP 0
R417 R418 R419 R420 R421
1-216-833-11 1-216-821-11 1-216-833-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 1K 10K 100 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
L302 L303 L500 L802 L803
1-216-864-11 1-216-864-11 1-469-844-11 1-457-376-11 1-457-376-11
SHORT CHIP SHORT CHIP INDUCTOR COIL, CHOKE COIL, CHOKE
R422 R430 R431 R432 R433
1-216-833-11 1-216-809-11 1-216-809-11 1-216-833-11 1-218-883-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 100 100 10K 33K
5% 5% 5% 5% 0.5%
1/10W 1/10W 1/10W 1/10W 1/10W
R440 R441 R442 R450 R451
1-216-809-11 1-216-809-11 1-216-833-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 10K 100 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R452 R453 R454 R455 R460
1-216-833-11 1-216-864-11 1-216-864-11 1-216-825-11 1-216-809-11
METAL CHIP SHORT CHIP SHORT CHIP METAL CHIP METAL CHIP
10K 0 0 2.2K 100
5%
1/10W
5% 5%
1/10W 1/10W
R461 R462 R470
1-216-809-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-809-11 METAL CHIP
100 10K 100
5% 5% 5%
1/10W 1/10W 1/10W
0 0 2.2uH
< TRANSISTOR > Q3 Q420 Q430 Q440 Q450
8-729-106-68 6-550-752-01 6-550-752-01 6-550-752-01 6-550-752-01
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SD1615A-GP DTC614TKT146 DTC614TKT146 DTC614TKT146 DTC614TKT146
Q460 Q470 Q491 Q492 Q501
6-550-752-01 6-550-752-01 8-729-027-23 8-729-027-43 8-729-027-23
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
DTC614TKT146 DTC614TKT146 DTA114EKA-T146 DTC114EKA-T146 DTA114EKA-T146
Q589
8-729-027-43 TRANSISTOR DTC114EKA-T146
www
.
xiaoy u163. com
40 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
Description
0 0 0 0 0
QQ
QQ
Part No.
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
13942296513
13942296513
Description
1-216-864-11 1-216-864-11 1-216-296-11 1-216-296-11 1-216-296-11
TEL
TEL
Part No.
JC53 JC100 JC300 JC301 JC302
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 MAIN
Ref. No.
5% 5%
1/10W 1/10W
Remark
5% 5%
R482 R483 R484 R491 R494
1-216-827-11 1-216-827-11 1-216-821-11 1-216-805-11 1-216-825-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
3.3K 3.3K 1K 47 2.2K
5% 5% 5% 5% 5%
R500 R501 R503
1-216-817-11 METAL CHIP 1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP
470 100K 100K
R504
1-216-845-11 METAL CHIP
R505
1-216-845-11 METAL CHIP
R507
1-216-845-11 METAL CHIP
R508
1-216-845-11 METAL CHIP
R509 R510 R512
1-216-845-11 METAL CHIP 1-216-833-11 METAL CHIP 1-216-845-11 METAL CHIP
5% 1/10W (GT560:E,MX/GT560S) 100K 5% 1/10W (GT560:E,MX/GT560S) 100K 5% 1/10W 10K 5% 1/10W 100K 5% 1/10W
R513 R514 R515 R516 R517
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100 100K
5% 5% 5% 5% 5%
R518 R519 R520 R521 R522
1-216-845-11 1-218-871-11 1-218-871-11 1-216-821-11 1-218-871-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 10K 10K 1K 10K
5% 0.5% 0.5% 5% 0.5%
R523 R524 R525 R526 R527
1-216-845-11 1-216-845-11 1-216-845-11 1-216-841-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 100K 47K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R528 R529 R530 R531 R532
1-216-833-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 100K 100K 100K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R533 R534 R535 R536 R537
1-216-845-11 1-216-845-11 1-216-809-11 1-216-811-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 100 150 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R538 R539 R540 R541 R543
1-216-845-11 1-216-809-11 1-216-809-11 1-216-849-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100 100 220K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R545 R546 R547 R548
1-216-845-11 1-216-845-11 1-216-827-11 1-216-825-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 3.3K 2.2K
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
.
Description
1/10W 1/10W
1-216-825-11 1-216-845-11 1-216-864-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP
2.2K 100K 0 1K 1K
1/10W 1/10W 1/10W 1/10W 1/10W
R555 R556 R557 R558 R559
1-216-833-11 1-216-833-11 1-216-809-11 1-216-809-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 10K 100 100 100K
5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W (GT51W/GT510)
R560
1-216-845-11 METAL CHIP
100K
R562 R563 R601 R602
1-216-845-11 1-216-845-11 1-216-851-11 1-216-851-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 330K 330K
5% 1/10W (GT560/GT560S) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W
R603 R604 R605 R606 R607
1-216-821-11 1-216-835-11 1-216-809-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 15K 100 1K 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R608 R610 R611 R701 R702
1-216-829-11 1-216-809-11 1-216-809-11 1-216-821-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
4.7K 100 100 1K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
100K
TEL 13942296513
www
Part No.
R549 R550 R551 R553 R554
5% 1/10W 5% 1/10W 5% 1/10W (GT560/GT560S) 100K 5% 1/10W (GT51W/GT510) 100K 5% 1/10W (GT51W/GT510/GT560:EA)
1/10W 1/10W 1/10W 1/10W 1/10W
Ref. No.
Remark
5% 5%
1/10W 1/10W
5% 5%
1/10W 1/10W
QQ 376315150 892498299 1/10W 1/10W 1/10W 1/10W 1/10W
R703 R704 R705 R706 R707
1-216-833-11 1-216-833-11 1-249-425-11 1-216-841-11 1-216-841-11
METAL CHIP METAL CHIP CARBON METAL CHIP METAL CHIP
10K 10K 4.7K 47K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/4W 1/10W 1/10W
R708 R709 R710 R711 R712
1-216-829-11 1-216-049-11 1-249-425-11 1-216-845-11 1-216-837-11
METAL CHIP RES-CHIP CARBON METAL CHIP METAL CHIP
4.7K 1K 4.7K 100K 22K
5% 5% 5% 5% 5%
1/10W 1/10W 1/4W 1/10W 1/10W
R801 R802 R803 R804 R805
1-218-859-11 1-218-883-11 1-218-875-11 1-216-851-11 1-216-844-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
3.3K 33K 15K 330K 82K
0.5% 0.5% 0.5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R806 R808 R809 R810 R811
1-216-847-11 1-216-821-11 1-216-821-11 1-216-823-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
150K 1K 1K 1.5K 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R812 R830
1-216-833-11 METAL CHIP 1-216-797-11 METAL CHIP
10K 10
5% 5%
1/10W 1/10W
< SWITCH > S102
1-786-458-11 SWITCH, PUSH (1 KEY) (FRONT PANEL DETECT) 1-692-431-21 SWITCH, TACTILE (RESET) 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) (GT560:E,MX/GT560S)
xiaoy u163. com S103 S501
41 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
100 10K 0 3.3K 3.3K
QQ
QQ
METAL CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP
13942296513
13942296513
Description
1-216-809-11 1-216-833-11 1-216-864-11 1-216-827-11 1-216-827-11
TEL
TEL
Part No.
R471 R472 R474 R480 R481
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 MAIN
Ref. No.
SERVO
Part No.
SUB
Description
Remark
Ref. No.
Part No.
TH400
Remark
1-803-350-21 THERMISTOR, POSITIVE
1-479-077-13 REMOTE COMMANDER (RM-X151) 2-548-729-01 LID, BATTERY CASE (for RM-X151) 2-698-276-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (GT51W:US) 2-698-276-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH) (GT51W:CND/GT510) 2-698-276-41 MANUAL, INSTRUCTION (ENGLISH,SPANISH, SIMPLIFIED CHINESE) (GT560:E,MX/GT560S)
< TUNER UNIT > TU1
Description
ACCESSORIES ************
< THERMISTOR (POSITIVE) >
A-3220-961-B TUNER UNIT (TUX-032) < VIBRATOR >
X500 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz) X501 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz) *************************************************************
2-698-276-51 MANUAL, INSTRUCTION (ENGLISH)
SUB BOARD ********** 1-833-591-11 CABLE, FLEXIBLE FLAT (20 CORE) < CONNECTOR > CN201
1-818-142-11 SOCKET, CONNECTOR 20P
X-2149-228-1 CASE ASSY (for FRONT PANEL) (EXCEPT US) *************************************************************
< DIODE > PARTS FOR INSTALLATION AND CONNECTIONS ***************************************
R201 R202
1-216-812-11 METAL CHIP 1-216-815-11 METAL CHIP
180 330
5% 5%
1/10W 1/10W
< SWITCH > S201 1-786-653-21 SWITCH, TACTILE (Z) *************************************************************
151 152 153 154 155
X-3382-647-1 1-833-102-11 3-246-471-01 2-638-099-01 X-3381-154-1
FRAME ASSY, FITTING CORD (WITH CONNECTOR) (POWER) KEY (FRAME) COLLAR SCREW ASSY (BS4), FITTING (GT560/GT560S)
156 157
3-349-410-11 BUSHING (GT560/GT560S) 3-934-325-01 SCREW, +K (5X8) TAPPING
QQ 376315150 892498299 151
152
153
MISCELLANEOUS *************** 12 1-833-102-11 CORD (WITH CONNECTOR) (POWER) 0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A) FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A *************************************************************
×2
154
155 156
157 ×4
www
.
xiaoy u163. com
42 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
TEL 13942296513 < RESISTOR >
QQ
QQ
LED201 8-719-053-09 LED SML-310VTT86 (DISC IN) LED202 8-719-053-09 LED SML-310VTT86 (Z)
13942296513
13942296513
(GT560:EA) 2-698-277-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH) (GT51W:US) 2-698-277-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH, FRENCH) (GT51W:CND/GT510) 2-698-277-41 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH,SIMPLIFIED CHINESE) (GT560:E,MX/GT560S) 2-698-277-51 MANUAL, INSTRUCTION, INSTALL (ENGLISH) (GT560:EA)
TEL
TEL
A-1177-362-A SERVO BOARD, COMPLETE ********************** *************************************************************
http://www.xiaoyu163.com
CDX-GT51W/GT510/ GT560/GT560S
QQ 376315150 892498299
US Model Canadian Model CDX-GT51W/GT510
SERVICE MANUAL
E Model CDX-GT560/GT560S
Ver. 1.2 2007.04
Subject: Notes for removal of the OPTICAL PICK-UP added.
1. CHUCKING ARM SUB ASSY
3 chucking arm sub assy
1 spring
2
Note: Have this portion receive the chassis.
Note: Have this portion receive the chassis.
Note: Be careful not to touch the turn table.
www 9-887-402-81
.
xiaoy u163. com http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
QQ 376315150 892498299
TEL 13942296513
QQ
QQ
DISASSEMBLY
13942296513
13942296513
File this supplement with the service manual.
TEL
TEL
SUPPLEMENT-1
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299
2. SLED MOTOR ASSY
2 three serration screws (M 2 × 3)
3 sled mtor assy 1 spring
turn table
spring stand
TEL
TEL stand Note: Place the stand with care not to touch the turn table.
QQ 376315150 892498299 three serration screws (M 2 × 3)
sled mtor assy
Note: Take care to prevent the chassis from being bent when tightening the three machine screws.
www
.
xiaoy u163. com
2 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
Note for Assembly
QQ
QQ
TEL 13942296513
13942296513
13942296513
Note: Never remove these parts since they were adjusted.
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299 3. OPTICAL PICK-UP SECTION
2 optical pick-up section
1
TEL
TEL
13942296513
13942296513
Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section.
QQ
QQ
4. OPTICAL PICK-UP
376315150 892498299
376315150 892498299
QQ 376315150 892498299
TEL 13942296513
1 pan tapping screw (M 1.4 × 2.5) 2 leaf spring (sub guide) 3 leaf spring (OP)
5 optical pick-up 4 lead screw assy
Notes for Assembly
www
xiaoy u163. com
Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base.
.
Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base.
There is space at the end of the leaf spring (sub guide) to avoid contact with the slide.
3 http://www.xiaoyu163.com
http://www.xiaoyu163.com
CDX-GT51W/GT510/GT560/GT560S
QQ 376315150 892498299
REVISION HISTORY
Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver.
Date
Description of Revision
1.0
2006.09
New
1.1
2006.12
Correction of disassembly of OPTICAL PICK-UP.
1.2
2007.04
Notes for removal of the OPTICAL PICK-UP added. (SUPPLEMENT-1)
(ENG-07003)
TEL
TEL
13942296513
13942296513
.
xiaoy u163. com
4 http://www.xiaoyu163.com
376315150 892498299
376315150 892498299
www
QQ 376315150 892498299
QQ
QQ
TEL 13942296513
