Transcript
CDX-R3000/R3000T SERVICE MANUAL
AEP Model UK Model
Ver 1.0 2003. 12
CDX-R3000
E Model CDX-R3000T
Photo: CDX-R3000
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
NEW
CD Drive Mechanism Type
MG-611XA-186//Q
Optical Pick-up Name
KSS1000E
SPECIFICATIONS CD player section Signal-to-noise ratio Frequency response Wow and flutter
Power amplifier section 120 dB 10 – 20,000 Hz Below measurable limit
Outputs
Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 50 W × 4 (at 4 ohms) (CDX-R3000) 52 W × 4 (at 4 ohms) (CDX-R3000T)
Tuner section FM Tuning range Aerial terminal Intermediate frequency Usable sensitivity Selectivity Signal-to-noise ratio
General
87.5 – 108.0 MHz External aerial connector 10.7 MHz/450 kHz 9 dBf 75 dB at 400 kHz 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz
Outputs
Inputs
Tone controls
MW/LW (CDX-R3000) Tuning range MW: 531 – 1,602 kHz LW: 153 – 279 kHz Aerial terminal External aerial connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity MW: 30 µV LW: 40 µV AM (CDX-R3000T) Tuning range Aerial terminal Intermediate frequency Sensitivity
531 – 1,602 kHz External aerial connector 10.7 MHz/450 kHz AM: 30 µV
Audio outputs terminal (rear/sub switchable) Power aerial relay control terminal Power amplifier control terminal Telephone ATT control terminal (CDX-R3000) Remote controller input terminal Aerial input terminal Low: ±10 dB at 60 Hz (XPLOD) Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz (XPLOD)
– Continued on next page –
FM/MW/LW COMPACT DISC PLAYER CDX-R3000
FM/AM COMPACT DISC PLAYER CDX-R3000T 9-961-414-01
Sony Corporation
2003L04-1 © 2003. 12
e Vehicle Company Published by Sony Engineering Corporation
1
CDX-R3000/R3000T
Power requirements Dimensions Mounting dimensions Mass Supplied accessories
12 V DC car battery (negative ground) Approx. 178 × 50 × 179 mm (w/h/d) Approx. 182 × 53 × 161 mm (w/h/d) Approx. 1.2 kg Parts for installation and connections (1 set) Front panel case (1)
If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block. optical pick-up
Design and specifications are subject to change without notice.
SERVICE NOTES
This label is located on the bottom of the chassis. NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
semi-fixed resistor
TEST DISCS This set can playback CD-R and CD-ROM discs. The following test discs should be used to check the capability: CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) CD-RW test disc TCD-W082L (Part No. J-2502-063-2) Notes on CD-R/CD-RW discs • You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs) designed for audio use on this unit. Look for these marks to distinguish CD-Rs/CD-RWs for audio use.
Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. These marks denote that a disc is not for audio use.
• Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. • You cannot play a CD-R/a CD-RW that is not finalized*. * A process necessary for a recorded CD-R/CD-RW disc to be played on the audio CD player.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
CDX-R3000/R3000T
z
UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CNP301) and the SERVO board (CN1) with the extension cable (Part No. J-2502-076-1).
MAIN BOARD CNP301
J-2502-076-1
SERVO BOARD CN1
3
CDX-R3000/R3000T
TABLE OF CONTENTS 1. GENERAL Location of controls ................................................................. 5 Connections ............................................................................. 6
2. DISASSEMBLY 2-1. Sub Panel Assy .................................................................... 8 2-2. CD Mechanism Block ......................................................... 9 2-3. Main Board ......................................................................... 9 2-4. Chassis (T) Sub Assy ........................................................ 10 2-5. Roller Arm Assy ................................................................ 10 2-6. Chassis (OP) Assy ............................................................. 11 2-7. Optical Pick-up ................................................................. 11 2-8. SL Motor Assy (M902) ..................................................... 12 2-9. LE Motor Assy (M903) ..................................................... 12 2-10. Servo Board ....................................................................... 13
3. DIAGRAMS 3-1. IC Pin Descriptions ........................................................... 14 3-2. Block Diagram –CD Section– ........................................... 19 3-3. Block Diagram –Tuner Section– ....................................... 20 3-4. Block Diagram –Display Section– .................................... 21 3-5. Printed Wiring Boards –CD Mechanism Section– ............ 22 3-6. Schematic Diagram –CD Mechanism Section– ................ 23 3-7. Printed Wiring Board –Main Section– .............................. 24 3-8. Schematic Diagram –Main Section (1/2)– ........................ 25 3-9. Schematic Diagram –Main Section (2/2)– ........................ 26 3-10. Printed Wiring Board –Key Section– ................................ 27 3-11. Schematic Diagram –Key Section– ................................... 28 3-12. IC Block Diagrams ............................................................ 29
4. EXPLODED VIEWS 4-1. 4-2. 4-3. 4-4. 4-5. 4-6.
Main Section ..................................................................... 32 Front Panel Section ........................................................... 33 CD Mechanism Section (1) ............................................... 34 CD Mechanism Section (2) ............................................... 35 CD Mechanism Section (3) ............................................... 36 CD Mechanism Section (4) ............................................... 37
5. ELECTRICAL PARTS LIST ........................................ 38
4
CDX-R3000/R3000T SECTION 1 GENERAL
(CDX-R3000)
This section is extracted from instruction manual.
(CDX-R3000T)
5
CDX-R3000/R3000T
Connections (CDX-R3000)
6
CDX-R3000/R3000T
Connections (CDX-R3000T)
7
CDX-R3000/R3000T SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence.
SET 2-1.
SUB PANEL ASSY (Page 8)
2-2.
CD MECHANISM BLOCK (Page 9)
2-3.
MAIN BOARD (Page 9)
2-7.
2-4.
CHASSIS (T) SUB ASSY (Page 10)
2-5.
ROLLER ARM ASSY (Page 10)
2-6.
CHASSIS (OP) ASSY (Page 11)
2-8.
SL MOTOR ASSY (M902) (Page 12)
2-10. SERVO BOARD (Page 13)
2-9.
OPTICAL PICK-UP (Page 11)
LE MOTOR ASSY (M903) (Page 12)
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL ASSY
3 two claws
2 two claws
1 two screws (+PTT 2.6 x 6)
4 sub panel assy
8
CDX-R3000/R3000T
2-2. CD MECHANISM BLOCK 7 bracket (CD) 8 shield sheet 6 two screws (+PTT 2.6 x 4)
5 CD mechanism block
2 screw (+PTT 2.6 x 6)
3
1 screw (+PTT 2.6 x 6)
4 CNP301
2-3. MAIN BOARD
1 three ground point screws (+PTT 2.6 x 6)
2 two screws (+PTT 2.6 x 6)
3 MAIN board
9
CDX-R3000/R3000T
2-4. CHASSIS (T) SUB ASSY 4 claw 2 two screws (+P 1.7 x 2.2) 1 two screws (+P 1.7 x 2.2)
6 chassis (T) sub assy
5 SENSOR board
3 claw
2-5. ROLLER ARM ASSY
3 washer
5 roller arm assy
4 worm wheel (RA)
2 spring (RAR)
1 spring (RAL)
10
CDX-R3000/R3000T
2-6. CHASSIS (OP) ASSY 8 qa chassis (OP) assy
0 coil spring (damper)
lever (D) 4 washer 1 CN2 6 9 two coil springs (damper)
5 gear (LE1)
7
slider (R) 3 tension coil spring (KF) 2 Remove the six solderings.
2-7. OPTICAL PICK-UP
2 chucking arm sub assy
5 claw
1 tension coil spring (CHKG)
7 optical pick-up
6 main shaft
4 rack (SL) 3 screw (+B 1.4 x 5)
11
CDX-R3000/R3000T
2-8. SL MOTOR ASSY (M902)
1 screw (+P 1.4 x 1.8)
2 SL motor assy (M902)
2-9. LE MOTOR ASSY (M903)
0 woam (LEB) assy
8 screw (+M 1.7 x 2.5) 9 bearing (LEB)
qf two toothed lock screws (+M 1.4 )
qa screw (+M 1.7 x 2.5)
2 washer 3 gear (LE1)
lever (D)
4
bracket (LEM) qs screw (+M 1.7 x 2.5)
qd
qg LE motor assy (M903)
5
6 screw (+P 1.7 x 2.2)
slider (R) 7 leaf spring (LE) 1 Remove the soldering.
12
CDX-R3000/R3000T
2-10. SERVO BOARD 1 Remove the eight solderings.
6 SERVO board
2 Remove the three solderings. 4 toothed lock screw (M 1.7)
5 claw
3 CN2
13
CDX-R3000/R3000T SECTION 3 DIAGRAMS 3-1. IC PIN DESCRIPTIONS • IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name I/O Pin Description 1 LD O Laser diode ON/OFF control signal output (L: laser OFF, H: laser ON)
14
2 3
PD PN
I I
Dimmer monitor input from optical pick-up laser diode. Not used. (Fixed at L in this set)
4 5
AVDD DGND
— —
Analog power supply pin (+3.3 V) Ground
6 7
RFOK INTQ
O O
RFOK signal output to system control IC. CD text pack synchronization signal output to system control IC.
8
RST
I
9
A0
I
CD reset signal input from system control IC. Command/parameter discrimination signal input from system control IC.
10
STB
I
(L: command transmission, H: parameter transmission) Data strobe signal input from system control IC.
11 12
SCK SO
I O
Serial clock input from system control IC. Serial data output to system control IC.
13 14
SI DVDD
I —
Serial data input from system control IC. Power supply pin (+3.3 V)
15 16
DAVDD ROUT
— O
D/A converter power supply (+) pin (+3.3 V) Analog audio signal output (R-ch)
17 18
DAGND REGC
— —
Ground Capacitor connection pin for SCF regulator.
19 20
DAGND LOUT
— O
Ground Analog audio signal output (L-ch)
21 22 23
DAVDD XVDD XTAL
— — O
D/A converter power supply (+) pin (+3.3 V) Power supply pin (+3.3 V) Main system clock output (16.9344 MHz)
24 25
XTAL XGND
I —
Main system clock input (16.9344 MHz) Ground
26 27
DVDD C1D1/FZD
— O
Power supply pin (+3.3 V) Not used. (Open)
28 29
C1D2/TZD C2D1/RMUTE
O O
Not used. (Open) CD R-ch data zero detection signal output
30 31
C2D2/LMUTE C2D3/SHOCK/SBSY
O O
CD L-ch data zero detection signal output Not used. (Open)
32 33
LOCK/FR WFCK/MIRR
O O
Not used. (Open) Not used. (Open)
34 35
RFCK/HOLD PLCK
O O
Not used. (Open) Not used. (Open)
36 37
C16M DGND
O —
Not used. (Open) Ground
38 39
TX EMPH/RAMOVER
O O
Not used. (Open) Not used. (Open)
40 41
FLAG DVDD
O —
Not used. (Open) Power supply pin (+3.3 V)
42
LIMIT
I
43
XTALEN
I
44
DGND
—
(Fixed at L in this set) Ground
45 46
DIN DOUT
I O
Not used. (Connect to DOUT in this set) Not used. (Connect to DIN in this set)
47 48
SCKIN SCKO
I O
Not used. (Connect to SCKO in this set) Not used. (Connect to SCKIN in this set)
49
LRCKIN
I
Not used. (Connect to LRCK in this set)
Not used. (Fixed at L in this set) Oscillation circuit ON/OFF control signal input (L: ON, H: OFF)
CDX-R3000/R3000T
Pin No. 50
Pin Name LRCK
I/O O
Pin Description Not used. (Connect to LRCKIN in this set)
51 52
DVDD FD+
— O
Power supply pin (+3.3 V) Focus servo drive PWM signal output (+)
53 54
FD– TD+
O O
Focus servo drive PWM signal output (–) Tracking servo drive PWM signal output (+)
55 56
TD– SD+
O O
Tracking servo drive PWM signal output (–) Sled servo drive PWM signal output (+)
57 58
SD– MD+
O O
Sled servo drive PWM signal output (–) Spindle servo drive PWM signal output (+)
59 60
MD– DGND
O —
Spindle servo drive PWM signal output (–) Ground
61 62 to 66
TESTEN TEST4 to TEST0
I I
67 68
ADGND EFM
— O
A/D converter power supply (–) pin EFM signal output
69 70
ASY ADVDD
I —
EFM comparator reference voltage input A/D converter power supply pin (+3.3 V)
71 72
RFI EQ2
I —
RF signal input for EFM data growing. Not used. (Open)
73 74
EQ1 RF–
— I
RF amplifier equalizer parts connection pin Not used. (Open)
75 76
RF2– AGCO
I O
RF amplifier inversion input RF signal output after on AGC.
77 78 79
AGCI RFO ATEST
I O I
RF AGC signal amplifier input RF signal output before on AGC. Not used. (Open)
80 81
C3T AGND
— —
Capacitor connection pin for 3T detection. Ground
82 83
A C
I I
Signal input (A) from optical pick-up detector. Signal input (C) from optical pick-up detector.
84 85
B D
I I
Signal input (B) from optical pick-up detector. Signal input (D) from optical pick-up detector.
86 87
F E
I I
Signal input (F) from optical pick-up detector. Signal input (E) from optical pick-up detector.
88 89
VREFIN AVDD
I —
Reference voltage (+1.65 V) input Analog power supply pin (+3.3 V)
90 91
REFOUT REFC
O —
Reference voltage (+1.65 V) output Capacitor connection pin for reference voltage output.
92 93
FE– FEO
I O
Focus error signal amplifier inversion input Focus error signal amplifier output
94 95
ADCIN TE–
I I
Not used. (Open) Tracking error signal amplifier inversion input
96 97
TEO TE2
O O
Tracking error signal amplifier before output Tracking error signal amplifier after output
98 99
TEC AGND
I —
Tracking error signal comparator input Ground
100
PWMSW
I
Test setting input (Fixed at L in this set) Test setting input (Fixed at L in this set)
Not used. (Fixed at L in this set)
15
CDX-R3000/R3000T
• IC501 MN101E01KDD (SYSTEM CONTROL) (MAIN BOARD (2/2)) Pin No. Pin Name I/O Pin Description 1 DAVDD — D/A converter power supply (+) pin (+3.3 V) 2 3
NCO DAVSS
O —
Not used. (Open) D/A converter power supply (–) pin
4 5
UNISO UNISI
O I
Not used. (Open) Not used. (Fixed at L in this set)
6
UNICKO
O
7
RETRA
I
Not used. (Fixed at L in this set) Retractable CD door open/close detection switch input
8, 9
NCO
O
(L: CD door open, H: CD door close) Not used. (Open)
10 11
VDD1 MMOD
— I
Power supply pin (+3.3 V) Not used. (Fixed at L in this set)
12 13
OSCOUT OSCIN
O I
Main clock output (27 MHz) Main clock input (27 MHz)
14 15
VSS1 XIN
— I
Ground Sub clock input (32.768 kHz)
16 17
XOUT VDD2
O —
Sub clock output (32.768 kHz) Power supply pin (+3.3 V)
18 19
MOD1 RESET
— I
Not used. (Fixed at H in this set) Microcomputer reset input
20 21
RCIN1 ACCIN
I I
Rotary commander SHIFT key input Accessory power supply detection input
22 23
TESTIN TELATT
I I
Test mode detection input Telephone attenuator detection input (CDX-R3000)
24 25 26
ATT XKEYON NCO
O O O
Audio mute control output Key power supply control output Not used. (Open)
27 28
KEYACK TU_ATTIN
I I
Key acknowledge detection input Mute zero cross detection input from tuner unit. (CDX-R3000)
29, 30 31
NCO BUIN
O I
Not used. (Open) Backup power supply detection input
32 33
CD_INTQ CD_SO
I O
CD text pack synchronization signal input from CD servo IC. Serial data output to CD servo IC.
34 35
CD_SI CD_SCK
I O
Serial data input from CD servo IC. Serial clock output to CD servo IC.
36 37
BUSON SYSRST
O O
Not used. (Fixed at H in this set) Not used. (Fixed at H in this set)
38 39
CD_RFOK CD_RST
I O
RFOK signal input from CD servo IC. Reset signal output to CD servo IC.
40 41
CD_A0 CD_STB
O O
Command/parameter discrimination signal output to CD servo IC. Data strobe signal output to CD servo IC.
42 43
CD_MUTE-R CD_MUTE-L
I I
Mute zero cross detection input (R-ch) from CD mechanism deck. Mute zero cross detection input (L-ch) from CD mechanism deck.
44 45
CD_INSW CD_SELFSW
I I
Disc in switch detection input from CD mechanism deck. Self switch detection input from CD mechanism deck.
46 47
CD_LM_LO CD_LM_EJ
O O
Loading motor control output to CD mechanism deck. (Loading direction) Loading motor control output to CD mechanism deck. (Eject direction)
48 49
CD_DSW CD_LIMIT
I I
Down switch detection input from CD mechanism deck. Limit switch detection input from CD mechanism deck.
50 51
AMPATT AREASEL2
O O
Not used. (Fixed at L in this set) Not used. (Open)
52 53
AREASEL1 AREASEL0
O I
Not used. (Open) Destination area initial setting input (L: CDX-R3000T, H: CDX-R3000)
16
CDX-R3000/R3000T
Pin No. 54
Pin Name COL_SW
I/O I
Pin Description 1 color/2 color select input (L: 1 color, H: 2 color) (Fixed at L in this set)
55 to 57 58
NCO PANEL_SW
O I
Not used. (Open) Front panel detach detection input (L: with front panel, H: without front panel)
59 60
DIAG VOLATT
I O
Mode input from power amp IC. Attenuator control output to electronic volume IC.
61 62
NOSE-SW NCO
O O
Not used. (Open) Not used. (Open)
63 64
VSS2 TU-ATT
— O
Ground Tuner mute control output
65 66
NCO (TUNON) NS_MASK
O O
Not used. (Open) Noise mask output (CDX-R3000)
67 68
EEP_CKO EEP_SIO
O I/O
69 70
DOOR-IND AMPSTB
O O
Not used. (Open) Standby control output to power amp IC.
71 72
NCO LCDSO/FLS_SO
O O
Not used. (Open) Serial data output to LCD driver IC.
73 74
LCDCE/FLS_SI LCDCKO
O O
Chip enable output to LCD driver IC. Serial clock output to LCD driver IC.
75 to 78 79
NCO I2C_SIO
O I/O
80 81
NCO I2C_CKO
O O
Not used. (Open) I2C bus serial clock output
82 83 84
DAVN SIRCS NCO
I I O
RDS data block synchronization detection input (CDX-R3000) SIRCS signal input Not used. (Open)
85 86 to 88
BEEP NCO
O O
Beep output to power amp IC. Not used. (Open)
89 90
VDD3 NCO
— O
Power supply pin (+3.3 V) Not used. (Open)
91 92
VSS3 QUALITY
— I
Ground Noise detection input (CDX-R3000)
93 94, 95
VSM KEYIN1, 0
I I
S-meter voltage detection input Key input 1, 0
96 97 to 99
RCIN0 NCO
I O
Rotary commander key input Not used. (Open)
100
VREF+
—
A/D converter power supply (+) pin (+3.3 V)
Serial clock output to EEPROM communication. Serial data input/output with EEPROM communication.
Not used. (Open) I2C bus serial data input/output
17
CDX-R3000/R3000T
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • % : indicates tolerance. f • : internal component. • C : panel designation.
• Waveforms — Servo Board — (MODE: CD PLAY)
1 1.2Vp-p 16.9344MHz
(XTAL)
wd
IC1
2 1.6Vp-p
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • A : B+ Line. • Power voltage is dc 14.4V and fed with regulated dc power supply from ACC and BATT cords. • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : FM f : AM (CDX-R3000T) or MW (CDX-R3000) J : CD for printed wiring boards: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. a • : Through hole. • : Pattern from the side which enables seeing. (The other layer’s patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A)
(AGCI)
uj
IC1
3 0V Approx. 620mVp-p
od
IC1
(FEO)
4 0V Approx. 200mVp-p
oh
IC1
(TEO)
— Main Board —
1 Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
2.1Vp-p
8.664MHz
IC51
q;
(XTO)
2 1.6Vp-p
27MHz
IC501
qs
(OSCOUT)
3 2.2Vp-p 32.768kHz
IC501
18
qh
(XOUT)
CDX-R3000/R3000T
3-2. BLOCK DIAGRAM — CD SECTION —
RF AMP,DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR IC1
OPTICAL PICK-UP (KSS1000E)
82
83
A
C RF EQ
B 84
LOUT 20 ROUT 16
D/A CONV
EFM DEMOD
D
I-V CONV.
INTQ
85
SI SO
FORCUS ERROR
SCK
I/F
STB A0
E 87 86 PD
2
F PD
RST
TRACKING ERROR
(Page 20) TUNER SECTION
SERVO CTL
RFOK
LD AMP
CDL CDR
A SYSTEM CONTROL IC501 (1/3)
7
32 CD_INTQ
13
33 CD_SO
12
34 CD_SI
11
35 CD_SCK
10
41 CD_STB
9
40 CD_A0
8
39 CD_RST
6
38 CD_RFOK
OSC
LD
1
LD
52 53 54 55 56 57 58 59 FOCUS/TRACKING COIL DRIVE, SLED/SPINDLE/LOADING MOTOR DRIVE IC2
12
FOCUS COIL
11
13
TRACKING COIL
14
FSC+ FSC-
TRK+ TRK-
LMUTE 30 RMUTE 29
FD+ FDTD+ TDSD+ SDMD+ MD-
LD DRIVE Q1
FOCUS COIL DRIVE
FD+ 5 FD6
TRACKING COIL DRIVE
TD+ 2 TD3
23
43 CD_MUTE-L 42 CD_MUTE-R
24
X1 16.9344MHz SW3 (DISC IN) SW2 (SELF) SW4 (LIMIT)
M902 (SLED)
M901 (SPINDLE)
+
M
-
15 16
+
M
-
17 18
SLSL+
SPSP+
SLED MOTOR DRIVE
SD+ 27 SD26
SPINDLE MOTOR DRIVE
MD+ 24 MD23
SW1 (DOWN)
44 CD_INSW
45 CD_SELFSW
49 CD_LIMIT
48 CD_DSW IC602 RESET 19
1
RESET
S702 (RESET) M903 (LOADING)
+
M
-
9 10
LDLD+
LOADING MOTOR DRIVE
LOAD EJECT
1
46 CD_LM_LO
28
47 CD_LM_EJ A3.3V
SERVO 3.3V
AU3.3V
Signal path
D3.3V DR6V
: CD MECH6V
19
19
3
3.3V
CDX-R3000/R3000T
3-3. BLOCK DIAGRAM — TUNER SECTION —
SOUND CONTROL ELECTRONIC VOLUME IC401
L -1
NC 5
R
R-CH
BUS-LCH
J330 AUDIO OUT REAR
-2 POWER AMP IC750 (1/2)
A CD (Page 19) SECTION
TUNER UNIT TU1 J1 (ANTENNA)
1 ANT
CDR
OUT -RL
TONE 7
22
R-CH
SDA 31 SCL 30 29
R3000
16 MPX
I2C BUS
CONT.
SDA 12 SCL 11
OUTSUB-L
MUTE
60 VOLATT 82 DAVN
INTN 15 1 7
R-CH 3 RR+ 11 RR-
MUTE Q481
CONT. I2C BUS
R3000
TELATT 23
TEL ATT Q651
ACC CHECK Q631
ACCIN 21
93 VSM 79 I2C_SIO 81 I2C_CKO
92 QUALITY
BATT
LINE MUTE CONTROL Q478,479
MULTIPLE VOLTAGE REGULATOR IC750 (2/2)
25 DIAG
DIAG 59
68 EEP_SIO 67 EEP_CKO
R3000
PANEL+B MECH 6V SERVO 3.3V AUDIO 8.3V VP
3.3V SYSRST BUSON UNISI UNICKO UNISO BUIN
37 36 5 6 4 NC 31
+5V REG. Q1
D759
5 ANP-R
D760
6 ANT-R
3.3V
8 GND
PANEL+B MECH 6V SERVO 3.3V AUDIO 8.3V
19 17 F901 10A 18
BATT
16 +B (BATT)
BACK-UP CHECK/ LOW VOLTAGE CHECK Q581,582
28 TU_ATTIN 64 TU_ATT
MUTE-CONDITION 8 TU-MUTE 7
ANT-REM 27 B.UP+B 37 34 33 31 30 35
66 NS-MASK
E2P-SDA 17 E2P-SCL 16
7 ACC 15 TEST
ATT 24
AMP-REM 29 NS MASK SWITCH Q22
13 ATT
TESTIN 22
R3000
TU-VDD (TU5V) 11
VP2 6 VP1 20
AMPSTB 70 BEEP 85
3.3V
S-METER 6 TU-SDA 14 TU-SCL 13
QUALITY 5
2 RL+ 10 RL-
SYSTEM CONTROL IC501 (2/3)
10 XTO
TU 5V REG Q51,52
1 FL+ 9 FL-
4 FR+ 12 FR-
STB 22 BEEP 16
17
SDA 2 SCL 4
9 XTI
X51 8.664MHz
9 7
MUTE Q461
RDS DEMODULATOR IC51 RDS 9
11
TV-LCH EVR
R-CH 3
12 MUTE Q441
R-CH
L-CH 4
23
MUTE
CD-LCH
5 3
MUTE
9
INPUT SELECTOR
CDL
CN601 OUT -FL
EFFECT
OVER VOLTAGE DET. Q580,D580,581
BATT
• Signal path : FM
AUDIO 8.3V
: AM (CDX-R3000T) or MW (CDX-R3000)
VCC (8.3V) 10
: CD • R-ch is omitted due to same as L-ch.
20
20
CDX-R3000/R3000T
3-4. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL IC501 (3/3)
LCD DRIVER IC901
KEY MATRIX 95 KEYIN0
S900-908, 910-922
94 KEYIN1
LCDSO 72 LCDCKO 74 LCDCE 73
DATA 64 DI CLK 63 CL 62 CE
3 | 50
LCD LCD901
COM4 51 | | COM1 54
D502 KEY ACTIVE Q664
SEG3 | SEG50
27 KEYACK 1 ON/OFF 25 XKEYON
D501 PANEL +B
20 RCIN1 96 RCIN0
J561 (REMOTE IN)
IC971 REMOTE 3 RECEIVER
4
)
4
IC981 PANEL +B
(
83 SIRCS
LED902-908, 910-922 KEY ILLUMINATION
PANEL +B
3 VLCD CONTROL
LED931,932 (LCD BACK LIGHT) LED ON/OFF SWITCH Q902
X502 32.768kHz
15 XIN 16 XOUT
OSCOUT 12 OSCIN 13
PANEL +B
LED DRIVER Q901 X501 27MHz
D963
D962
LED961 (DISC IND)
S961 OPEN
RETRA 7
21
21
CDX-R3000/R3000T
3-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 18 for Common Note for Printed Wiring Boards.
2
1
3
4
5
6
7
8
: Uses unleaded solder.
9
10
11
12
13
A C6
C11
C1 C32
C2
C29
C31
C28
R1
R13
C13
R11 IC1
C38
JR90
R12
CN
CN1
(Page 24)
2
R9
C34
M901
C79 R85 R84
E
R72 R77 R76 R70 R75 R73 R71 C73 C72 C71 C70
FB1
C19 C18
R14
C25
R6 R7 C20 C21
R15 C39
C35
JR41
C17
D
C23
Q1
C26
JR40
C27
C37
C
C7
C36
JR91
X1
C30
B
R44
R45
R41
C8
C3
C5 R42
R81
SW3
SW4
R82
R83
R80 M902
R78
R79
C76 C77
IC2
C74
C75
F
C78
R74
SW2 M903
G SW1
H
22
22
14
CDX-R3000/R3000T
3-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 18 for Common Note on Schematic Diagram and Waveforms. • Refer to page 29 for IC Block Diagrams.
C20
R9 C25
Q1
C18
R7
C21
C17
R6
TP33
R14 R15
C36
R13
TP32
C23
C19
TP19 CN2
TP31 C38
C37
TP30
TP20 C39
C26
TP29 TP14 R12
TP21
C35 C27
TP28 TP27 C34
R1
TP26 TP13
R11
C13
TP12 IC1
C28
TP11
TP22
TP10 TP9 C29
TP23
TP8 TP7
C30
TP6 TP5 TP4
TP24 TP25 C31
TP3 SW4 TP2
TP81
C32
TP1
TP80
CN1 C11
JR90 TP85 TP83
M901
TP63 TP62
C1
TP84
R45
TP82
M902
JR91
TP65 TP64
C5 C3
X1
C8
R44
C6
TP61 TP60 TP59 TP58 TP57 TP56 TP55
FB1
C2
TP54 TP48
C7 TP27
TP87
R41 JR40
TP52 TP51 TP53
R42
TP49 TP50
JR41
SW3 TP28
TP88
TP29
TP89
TP47
SW2
TP46 TP45 TP44
SW1
TP43 TP42 TP41
TP90 TP91
TP40
R70
R71
C70
R72
R73
C71
R74
R75
R76
R77
IC2
C79
R85
R84
C78
R83
R82
C72
C77
R81 R80
C73
C76
R79 R78
TP100 C74 TP75 M903
TP92 TP93
TP74 TP71 TP70 TP73 TP72
IC B/D
Note: • Voltage is dc with respect to ground under no-signal conditions. no mark : CD PLAY
23
23
C75
(Page 26)
CDX-R3000/R3000T 3-7. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 18 for Common Note on Printed Wiring Boards.
1
2
3
4
5
6
7
: Uses unleaded solder.
8
9
10
11
12
13
14
J330 J561
A
R3000T
C333
C764
JW9
IC750
JW134
JW8
JW4
JW5
JW137
JW6 D757
D753
JW31
JW29
JW28
R652
C752
C760
JW32
JW26
JW111
JW27
C622
JW23
D761
D751
D754
D752
D762
D758 C759
JW30
R653
CNP301
L304
JC681
JW116
L302
R479
C406
R504
C512 C514
D712
D715
JW128 D719
R505
R503 D502
C343 C306 C305
R515
JC501 D501
R671 R673
JW51
JW48
JW47
R563
R564
JW65 JW63
X501
JW64
R552
JW82
R536
C631
R535
R541
S702
CN701
J (Page 27)
R540
JW44
R508
R565
JW50
JW56
JW52
JW45
R516
C504 C502 C513
R501
JW60
R674
JW37
R634
JW58
R502
R543
R509
C516
R632
JW41
R514 JW112
JW62
C503
C501
R633 Q631
JW36
R584
R547
C510
Q581
Q664 X502
JW66
C511
Q580
R631
R524
C508 C507
R567
R513
D716
JW141
JW99
JW98
JW55
JW119
C515
R569
JW133
JW74
JW70
JW75
JW127
JW76
JW126
R558
JW57
JW117
R539
R672 C621 JC503 IC602
R566
R518
JW140
D720
R512
JW71
D710
D717
R706
D718
R556
IC501
JW125
JW138
JW105
I
JW104
R704
JW139
R705
C10
JW77
D711
R517
(Page 22)
R583
JW109
C517
X51
D580 JW107
D581
R506
R510 R511
R582
L301
Q582 R523
R636
R756
JW78
H
R568 C509
C59
C58
R54
R572
JW49
R55
IC51
R559
R525
R570
R53
C756
R560
JW115
L306 C307
JW106 L303
R526
R530
R557 R544
JW120
R52
C60
R549
R532
JW68
C57
JW80
R51
R571
R534
R56
C53
R9
JW88
JW122
C56
R521
JW83
JW124
R8
R57
R527 R507
JW73
G
C51
R5
JW89
JW85
R58
C518
JW121
Q51 C54
C55
R4
R59
R528
R550
JW123
R61
JW81 JW84
Q52
R60
C62
JW100
R551
R522
JW118
JW72
R7
JW86
JW54
JW79
Q1
R6
C407
R531
JW90
L305
R301
JW97
JW61
JW94 C5
R3
JW101
C412
JW43
L307
JW96
JW130 L1
C7
F
JW95
R752
JW129
D1
C754
R410 R411
JW92
C4 C13 R2
JW91
C6
C301
C302 C308 R302
C12 R1
JW33
JW113
C755
C303
D479
D601
JW39
R409 Q479 JW93
R3000
D609
JW46
C2
C479
R407
R609
JW53
R408
Q478
R406
JW131
C404
JW132
C3
IC401
C413
R654 Q651
C770
JW25
JW20
C761
C623
R405
C405
JW10
JW13 C462 D756
C758
C750
L601 C602
D760
JW24
R11
E
JW22
JW59
R29 C1
D755
C461 C451
C471
R10
C601
R651 D759
C769
Q451
JC401
C401
Q22
R452
C431
C617 C618 D651
Q461
C441 R451
C11
JW102
D
R462
R461 R441
JW110
JW17
R453
C481
TU1
JW2
JW42
R481
JW1
JW3
JW15 JW16
C442 R463
R431
C452
JW14
C753
R471
JC1
C
R433 R443
JC445
JW142
JW143
Q481
C763
C432
R442 R432
JW11
Q431
Q441
Q471
JW12
JC331
B J1
F901
JW7
C332
L563 L561
JW144 C765
L562
C771
C751
JW145
R472
JW146
R482
JC753
CN601
R585
JW136
• Semiconductor Location Ref. No. Location Ref. No. D761 D1 F-3 D762 D479 E-5 D501 I-6 (IC51) D502 I-5 IC401 D580 F-10 IC501 D581 F-10 IC602 D601 D-9 IC750 D609 D-9 (D651) C-8 Q1 D710 H-3 (Q22) D711 H-3 (Q51) D712 I-2 (Q52) D715 I-4 Q431 D716 H-3 Q441 D717 H-3 Q451 D718 H-3 Q461 D719 I-4 Q471 D720 H-3 Q478 D751 D-6 Q479 D752 D-6 Q481 D753 D-7 Q580 D754 D-6 Q581 D755 C-5 Q582 D756 C-5 Q631 D757 C-6 (Q651) D758 C-6 Q664 D759 C-7 D760 D-7 (
24
24
): CDX-R3000 only
Location D-8 D-8 G-2 E-3 H-6 H-8 B-6 F-3 D-2 G-3 G-3 B-4 B-4 D-4 C-4 B-3 E-5 E-5 C-3 F-10 G-10 G-10 G-9 D-8 H-9
CDX-R3000/R3000T
3-8. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 18 for Common Note on Schematic Diagram and Waveforms. • Refer to page 29 for IC Block Diagrams.
Q51
Q1
R51
C4 R61
IC B/D
J1 D1
C57
C58 C765
C56
C12
C55
C6
JC1
C54
C13
C53
C5
C51
R52
R60
R1
R54
TU1
C764
R53
Q52 C751
D751
IC51 C3
R5
R4
C7
R8
R29
Q22
C750
C10
R56
D753
R11 C62
D754 R55
R6
D752 R9
R57
R7
C1
R3
C2
R2
C752
R58 R10
IC B/D
X51 C59
C60
L1
D755 D756
R59 IC750 R433
IC B/D
CN601 D758
Q431
C431 R431 R432
JC401 C11
D757
C432
IC401
D759
D761
D760
D762
R442 C441 C401
Q441
R441
R443
C442
R453
C452
C412
R405 C404
C413
Q451
C451 R451
C405 C406
R406
C407
R407
R452
JC753 C753
R408 R409
C617
F901
C618
C754 JC331
Q461
R461
R609
C763
R462 C461
R463 C462
D609 R752
C755
R411
C756
C758 C602
R756
C601
L601
R410 D601 Q471
C471 R471
Q479
R472
D479
R479
JC445 C769 R482 C481
R481
C759 Q481
C770
Q478
C760 C479 C771 C761
R651 R652
C332 C333
(Page 26) Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ( ) : AM or MW < > : CD PLAY
25
25
J330
CDX-R3000/R3000T
3-9. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 18 for Common Note on Schematic Diagram and Waveforms.
(Page 25)
(Page 23)
CNP301
L303
C343
C301 L304
C302
C308
L302 R302
L305
L307
JC681
L306 R301 L301
C303 C307 IC602 C305 C306 C623 S702 C621
C622
JC503
R653 Q651 C518
R636
D651
R654
R531
R539 R559 R568
R530
R631
R633 Q631
R517
R515
R541
R516
R524
R540
R523
R525
R527
R572 R560
R526
R528 C509
R634
C631
R632
R571
R507
R563
R564
R532
R585 R556
Q581
R549 R584
Q664
D580
R582
D581
R583
Q580 R534 Q582
R506 R566
C515 C508
R557
X501
C507 R550
R551
X502 R547
IC501
R508
R509
R544
R543 C504
C517
R565
CN701
R570 C503 R704
R536 R535
R569 R552
C516
R514 R521
R504
C516 C511
C512 C513
D712
D711
D720
D710
D718
D717
D716
D501 R672
C514 R505
R522 R513
C502
R501
R567
R503
R502
C510
D719
D502
C501 R518
R558
(Page 28)
D715
R511
R512
R510
R705 R706
L563
JC501
J561 R671 R673
L562 R674 L561
26
26
Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ( ) : AM or MW < > : CD PLAY
CDX-R3000/R3000T 3-10. PRINTED WIRING BOARD — KEY SECTION — • Refer to page 18 for Common Note on Printed Wiring Boards.
2
1
4
5
6
7
8
9
10
11
12
13
LED902
S905
S906
S902
S911
LED906
LED911
R951
R933
B
14
LED905
A
3
: Uses unleaded solder.
LED961
R932
R950 R949 S922
S910 LCD901 LED931
LED932 LED922
S961
LED910 R931
C LED912 R913
IC971
LED904 S901
S907 LED907
S908 LED908
LED921
S921
S920 LED920
S919
LED918
S917 LED917
S916
S914
S915 LED916
LED919
LED903
S904
S918
LED914
LED915
LED913
CN901
I
R991
• Semiconductor Location Ref. No. Location Ref. No. IC971 D901 G-11 IC981 D902 G-10 D903 G-13 LED902 D962 G-5 LED903 D963 G-4 LED904 D964 G-5 LED905 D991 H-5 LED906 D992 H-9 LED907 LED908 IC901 G-8
Location D-14 H-6 A-13 D-3 D-2 A-1 B-2 D-7 D-5
R996 R995 R994
R997
Ref. No. LED910 LED911 LED912 LED913 LED914 LED915 LED916 LED917 LED918 LED919
Location C-12 B-13 C-13 D-12 D-11 D-15 D-9 D-9 D-8 D-7
27
Ref. No. LED920 LED921 LED922 LED931 LED932 LED961
Location D-6 D-5 C-3 C-11 C-4 B-7
Q901 Q902
G-4 G-4
27
C993 R993 C992
C994
D992 C995
R924
R971
R998 R925
R926
R961 R963
R962
R992 R985
C996
C982 C991
D991
C981
IC981
R988
R989
R987
IC901
R984
R986
R977
D902
D962
R975
Q902
R905
D963
R904
D964
Q901 R974
R981
R906
R982
R938 R937
R946
R983
R955 R957
D901
R978
R911
R912
D903
R901
C971
R918
R972
R941
R942
R903
R945
R919
R920
R917
R921 R922
R907
R915
R902
R916
(Page 24)
F
H
S912
R914
E
G
S900
S913
R956
D
S903
CDX-R3000/R3000T
3-11. SCHEMATIC DIAGRAM — KEY SECTION — • Refer to page 18 for Common Note on Schematic Diagram.
R972 R961 LED912
LED913
LED917
LED921
LED904
LED931
LED910
R962
CN901
R987 R998
R988
IC971 R989
C971
R963
R978
R931
LED914
LED918
LED908
R949
R955
R924
R950
R956
R925
R951
R957
R926
LED961
R932
R983
LED919
LED932
LED907 LED906
IC981 R997 R991 C981
LED922
LED911
D963 LED920
LED903
LED902
Q901
LED905
R937
R941
R945
R942
R946
D992
LED916
D962
D902
D901
(Page 26)
LED915
C982
R975
R933
R982
S961
R974
D903 R938
Q902
D964
R981
D991
R971
R993
C991
C992
R994
C993
R995
IC901
R996
C996 C995
R984 C994
R992
R986 R985
R977
S900
S910
R911
S901
S902
S903
S904
S905
S906
R901
R912
R902
R913
R903
R914
R904
R915
R905
R916
R906
R917
R907
R918
S911
S912
S913
S914
S915
S916 LCD901
S907
S908
R919
R920
R921
R922
S917
S918
S919
S920
S921
S922
Note: • Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM
28
28
CDX-R3000/R3000T
3-12. IC BLOCK DIAGRAMS
REV
OPIN4(+)
OPIN4(–)
OPOUT4
OPIN3(+)
OPIN3(–)
OPOUT3
MUTE
BIAS
GND
VO3(–)
VO3(+)
VO4(–)
VO4(+)
IC2 BA5966FP-FE2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
MUTE +
+
–
FWD
OUT R
–
+
–
+ LEVEL SHIFT
–
LEVEL SHIFT +
+
–
+
OPIN1(–)
OPOUT1
OPIN2(+)
OPIN2(–)
OPOUT2
8
9
10
11
12
13
14
VO1(+)
7
VO1(–)
6
VO2(+)
5
VO2(–)
4
VOL(+)
3
VOL(–)
2
VCC
1
OPIN1(+)
VCC
FWD
+
–
–
– –
–
LEVEL SHIFT +
–
+
+
+
+
OUT F
+
+
–
+ REV
–
+
+ –
–
+ – LEVEL SHIFT
– LOADING DRIVER
+
–
–
–
IC51 TDA7333-013TR (CDX-R3000)
3 INTERPOLATOR
BAND PASS FILTER
REF2 3 REF1 4
VSS 5
TM 6 VDDD 7
MPX
REF3 2
SINC4 FILTER
SIGMA DELTA CONVERTER
SINC4REG
VDDA 1
RAM RDS RDSREG BUFFER INTN DEMODULATOR & & SYNCHRONIZATION CONTROL LOGIC
16 MPX 15 INTN
SDAOUT SDAIN TEST LOGIC SCK I C/SPI & INTERFACE SPI PIN MUX'S TESTREG 2
14 13 12 11
CSN SA_DATAOUT SDA_DATAIN SCL_CLK
2 10 XTO OSCILLATOR 9 XTI
RESETN 8
29
CDX-R3000/R3000T
DGND
SDA
SCL
MUTE
SEL
ADJ
VCC
OUTF1
OUTR1
OUTF2
OUTR2
DS12
DS22
DS32
OUTS1
OUTS2
IC401 BD3808FS-FE2
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
I2C BUS LOGIC
FADER (0~-58, -∞dB)
VCO
FADER (0~-58, -∞dB)
FADER (0~-58, -∞dB)
EFFECT (0dB~ +20dB,2dB STEP)
BASS fo:60,70,80,100,120,140,160,200Hz Q:0.5,0.75,1,1.25
FADER (0~-58, -∞dB)
EFFECT (0dB~ +20dB,2dB STEP)
GAIN+ATT (+10~-29, -∞dB)
2ND ORDER LPF fc:OFF,80,120,160Hz Q: 0.707
2ND ORDER LPF
MIX TONE PASS
TONE PASS
MIDDLE fo:500Hz,1kHz Q:1
BASS,TREBLE, MIDDLE (-15dB~+15dB,1dB STEP)
BASS,TREBLE, MIDDLE (-15dB~+15dB,1dB STEP)
TABLE fo:5,7.5,10,12.5kHz
VOLUME (+23~-79dB,-∞dB 1dB STEP)
VOLUME (+23~-79dB,-∞dB 1dB STEP)
fc:40kHz
fc:40kHz
ANTI-ALIASING FILTER
ANTI-ALIASING FILTER
INPUT GAIN (0~15dB,1dB STEP)
INPUT GAIN (0~15dB,1dB STEP)
MUTE
MUTE
INPUT SELECTOR (4 STEREO INCLUDE 1 ISOLATION INPUT)
30
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
AGND
FIL
AP1
AN
AP2
B1
B2
C1
C2
D1
D2
DS11
DS21
DS31
NC
NC
VCC/2
CDX-R3000/R3000T
IC750 TDA8588BJ/N2
TAB 1 2 SDA OUT-FL- 3
I2C BUS 4 SCL
FL OUT-FL+ 5
6 VP2 OUT-RL- 7 RL
8 PGND3
OUT-RL+ 9
PROTECTION/ DIAGNOSTIC
IN-RR 15
12 IN-FL 14 IN-FR
MUTE
S-GND 13
10 SVR
MUTE
IN-RL 11
16 BEEP
VP
OUT-RR+ 17 RR
18 PGND2
OUT-RR- 19
20 VP1
OUT-FR+ 21 FR OUT-FR- 23
STANDBY/ MUTE
22 STB
CHIP DETECT/ DIAGNOSTIC
24 PGND1 BATTERY DETECTION
DIAG 25
TEMPERATURE PROTECTION
ENABLE LOGIC 26 RST
ANT-REM 27
SWITCH
AMP-REM 29
SWITCH
28 CRES
REGULATOR
30 AUDIO8.3V SERVO5V 31 MECH6V 33
32 GND 34 PANEL+B
VP 35
REFERENCE VOLTAGE B.UP+B 37
REGULATOR
36 CBU LOADDUMP PROTECTION
BACK-UP SWITCH
31
CDX-R3000/R3000T SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • -XX and -X mean standardized parts, so they may have some difference from the original one.
• Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color • Accessories are given in the last of this parts list.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
4-1. MAIN SECTION
A
not supplied #2
#1
7 A
not supplied
B
F901
MG-611XA-186//Q
4
#1
not supplied
6
3
5
#1 TU1
not supplied
B
2 #1
#1
1
Ref. No.
Part No.
Description
1 2 3 4 5
X-3384-176-1 3-042-244-11 X-3383-739-1 3-376-464-11 A-3283-384-A
PANEL ASSY, SUB SCREW (T) LOCK ASSY (S) SCREW (+PTT 2.6X6), GROUND POINT MAIN BOARD, COMPLETE (R3000)
5 6
A-3283-388-A MAIN BOARD, COMPLETE (R3000T) 3-246-481-01 PLATE (TU), GROUND
32
Remark
Ref. No. 7 7
Part No.
Description
Remark
F901 TU1 #1
1-776-206-21 CORD (WITH CONNECTOR) (POWER) (R3000T) 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER) (R3000) 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A A-3220-959-A TUNER UNIT (TUX-032//Q) 7-685-792-09 SCREW +PTT 2.6X6 (S)
#2
7-685-790-01 SCREW +PTT 2.6X4 (S)
CDX-R3000/R3000T
4-2. FRONT PANEL SECTION
61
60 59
58
#3
not supplied (KEY board)
not supplied #3
57 LCD901 not supplied
55
53 56
not supplied
51 not supplied not supplied
not supplied not supplied
54 52
not supplied
Ref. No.
Part No.
Description
51 51 52 53 54
X-3384-305-1 X-3384-308-1 3-258-947-01 1-780-096-11 A-3372-522-A
PANEL SUB ASSY, FRONT (R3000) PANEL SUB ASSY, FRONT (R3000T) FILTER (IR) CONDUCTIVE BOARD, CONNECTION RETRACTABLE ASSY
55 55 56
X-3384-304-1 BUTTON ASSY (R3000) X-3384-309-1 BUTTON ASSY (R3000T) 3-246-479-01 SPRING (RELEASE)
Remark
Ref. No. 57 58 59 60 61
Part No.
Description
3-258-952-01 3-258-948-01 3-258-937-01 X-3383-264-2 A-3372-517-A
SHEET (ILLUMINATOR) PLATE (CD), LIGHT GUIDE PANEL, FRONT BACK CASE ASSY (for FRONT PANEL) PANEL COMPLETE ASSY, FRONT (R3000)
Remark
61 A-3372-526-A PANEL COMPLETE ASSY, FRONT (R3000T) LCD901 1-805-451-11 DISPLAY PANEL, LIQUID CRYSTAL #3 7-685-106-19 SCREW +P 2X10 TYPE2 NON-SLIT
33
CDX-R3000/R3000T
4-3. CD MECHANISM SECTION (1) (MG-611XA-186//Q)
not supplied (SENSOR board)
102
101
109 #4
110 not supplied
not supplied
103
104 106
105 108 107
Ref. No.
Part No.
Description
101 102 103 104 105
A-3372-444-A 3-253-729-11 3-257-892-11 3-257-892-01 3-253-695-11
CHASSIS (T) SUB ASSY SPRING (LTR), TENSION COIL SPRING (DAMPER), COIL SPRING (DAMPER), COIL SPRING (KF), TENSION COIL
106
3-259-033-01 DAMPER (S)
34
Remark
Ref. No. 107 108 109 110 #4
Part No.
Description
3-352-758-31 A-3283-339-A X-3384-088-1 X-3384-089-1 7-627-552-87
SCREW (M1.7), TOOTHED LOCK SERVO BOARD, COMPLETE LEVER (L) ASSY LEVER (R) ASSY SCREW, PRECISION +P 1.7X2.2
Remark
CDX-R3000/R3000T
4-4. CD MECHANISM SECTION (2) (MG-611XA-186//Q)
155 156
157 154 (including M901)
#5
M902 not supplied
SW4
not supplied not supplied
not supplied
153
not supplied
151
152
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Ref. No.
Part No.
Description
151 152 0 153 154 155
A-3372-445-A 4-912-432-01 8-820-207-02 A-3372-448-A A-3372-449-A
CHASSIS (OP) COMPLETE ASSY SCREW (B1.4X5), TAPPING OPTICAL PICK-UP KSS1000E/K1RP CHASSIS (OP) SUB ASSY (including M901) ARM SUB ASSY, CHUCKING
Remark
Ref. No. 156 157 M902 SW4 #5
Part No.
Description
A-3372-446-A X-3384-090-1 A-3372-447-A 1-571-099-11 7-627-850-77
LEVER (SL) SUB ASSY LEVER (SL) ASSY MOTOR ASSY, SL (SLED) SWITCH (1 KEY) (LIMIT) SCREW, PRECISION +P 1.4X1.8
Remark
35
CDX-R3000/R3000T
4-5. CD MECHANISM SECTION (3) (MG-611XA-186//Q)
203
201 202
207 211
204
209 208
210
205
207 207 M903
#4
206
Ref. No.
Part No.
Description
201 202 203 204 205
3-348-993-01 3-259-024-01 A-3372-441-A 3-259-455-11 3-253-713-11
WASHER WHEEL (RA), WORM ARM ASSY, ROLLER SPRING (RAL) SPRING (RAR)
206 207
3-259-469-11 SPRING (LE), LEAF 2-134-636-21 SCREW (M1.7X2.5)
36
Remark
Ref. No.
Part No.
Description
208 209 210 211 M903
3-259-467-11 3-345-648-91 A-3372-450-A 3-259-468-11 A-3372-443-A
BRACKET (LEM) SCREW (M1.4), TOOTHED LOCK WORM (LEB) ASSY BEARING (LEB) MOTOR ASSY, LE (LOADING)
#4
7-627-552-87 SCREW, PRECISION +P 1.7X2.2
Remark
CDX-R3000/R3000T
4-6. CD MECHANISM SECTION (4) (MG-611XA-186//Q)
254 252
255 252 256 251
253
257
Ref. No. 251 252 253 254
Part No.
Description
3-259-429-11 3-344-223-01 3-259-470-11 3-253-755-11
WHEEL (LE), WORM WASHER GEAR (LE1) LEVER (D)
Remark
Ref. No. 255 256 257
Part No.
Description
Remark
3-899-829-01 WASHER (SLIT) 3-259-032-01 GEAR (LE2) A-3337-998-A CHASSIS (M) BLOCK ASSY
37
CDX-R3000/R3000T SECTION 5 ELECTRICAL PARTS LIST
KEY NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable
Ref. No.
Part No.
• Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. • CAPACITORS uF : µF • COILS uH : µH
Description
Remark
KEY BOARD ********** 1-780-096-11 CONDUCTIVE BOARD, CONNECTION 3-258-952-01 SHEET (ILLUMINATOR) < CAPACITOR > C971 C981 C982 C991 C992
1-135-834-11 1-165-908-11 1-135-834-11 1-164-227-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
2.2uF 1uF 2.2uF 0.022uF 0.1uF
C993 C994 C995 C996
1-107-826-11 1-162-964-11 1-127-715-11 1-165-908-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.001uF 0.22uF 1uF
10% 10%
6.3V 10V 6.3V 25V 16V
10% 10% 10% 10%
16V 50V 16V 10V
10%
< CONNECTOR > CN901
1-794-312-11 PIN, CONNECTOR 12P
Ref. No.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board.
Part No.
Description
LED907 LED908 LED910 LED911 LED912
6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01
LED LED LED LED LED
CL-195SR-CD-T (MODE) CL-195SR-CD-T (SEL) CL-195SR-CD-T (EQ3) CL-195SR-CD-T (SEEK +/>/M) CL-195SR-CD-T (SEEK –/./m)
Remark
LED913 LED913 LED914 LED914 LED915
6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01
LED LED LED LED LED
CL-195SR-CD-T (AF/TA) (R3000) CL-195SR-CD-T (SHUF) (R3000T) CL-195SR-CD-T (PTY) (R3000) CL-195SR-CD-T (REP) (R3000T) CL-195SR-CD-T (SENS/BTM)
LED916 LED917 LED918 LED918 LED919
6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01
LED LED LED LED LED
CL-195SR-CD-T (6) CL-195SR-CD-T (5) CL-195SR-CD-T (4/SHUF) (R3000) CL-195SR-CD-T (4) (R3000T) CL-195SR-CD-T (3/REP) (R3000)
LED919 LED920 LED921 LED922 LED931
6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01 6-500-459-01
LED LED LED LED LED
CL-195SR-CD-T (3) (R3000T) CL-195SR-CD-T (2) CL-195SR-CD-T (1) CL-195SR-CD-T (DSPL) NSCW505T-ARS (LCD BACK LIGHT R)
< DIODE > D901 D902 D903 D962 D963
8-719-085-72 8-719-083-66 8-719-978-33 8-719-072-70 8-719-404-50
DIODE DIODE DIODE DIODE DIODE
UMZ6.8ENTR UDZS-TE17-18B DTZ-TT11-6.8B MA2ZD14001S0 MA111-TX
D964 D991 D992
8-719-083-66 DIODE UDZS-TE17-18B 8-719-069-54 DIODE UDZS-TE17-5.1B 8-719-404-50 DIODE MA111-TX < IC >
IC901 IC971 IC981
6-705-180-01 IC LC75827W 6-600-163-01 IC RS-770 (IR) 6-705-374-01 IC MM3033DULE < LIQUID CRYSTAL DISPLAY >
LCD901 1-805-451-11 DISPLAY PANEL, LIQUID CRYSTAL
LED932 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT L) LED961 8-719-082-38 LED CL-270SR-C-TS (DISC IND) < TRANSISTOR > Q901 Q902
8-729-027-58 TRANSISTOR DTC143ZKA-T146 8-729-027-58 TRANSISTOR DTC143ZKA-T146 < RESISTOR >
R901 R902 R903 R904 R905
1-216-819-11 1-216-819-11 1-216-819-11 1-216-821-11 1-216-823-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
680 680 680 1K 1.5K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R906 R907 R911 R912 R913
1-216-823-11 1-216-825-11 1-216-819-11 1-216-819-11 1-216-819-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1.5K 2.2K 680 680 680
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R914 R915 R916 R917 R918
1-216-821-11 1-216-823-11 1-216-823-11 1-216-825-11 1-216-827-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1.5K 1.5K 2.2K 3.3K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R919
1-216-829-11 METAL CHIP
4.7K
5%
1/10W
< DIODE > LED902 LED903 LED904 LED905 LED906
38
6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01 6-500-450-01
LED LED LED LED LED
CL-195SR-CD-T (OFF) CL-195SR-CD-T (SOURCE) CL-195SR-CD-T (– (VOLUME)) CL-195SR-CD-T (ATT) CL-195SR-CD-T (+ (VOLUME))
CDX-R3000/R3000T MAIN
KEY Ref. No.
Part No.
Description
Part No.
Description
R920 R921 R922 R924 R925
1-218-867-11 1-216-833-11 1-216-835-11 1-216-805-11 1-216-807-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
6.8K 10K 15K 47 68
5% 5% 5% 5% 5%
Remark 1/10W 1/10W 1/10W 1/10W 1/10W
Ref. No. S906 S907 S908 S910 S911
1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31
SWITCH, TACTILE (+ (VOLUME)) SWITCH, TACTILE (MODE) SWITCH, TACTILE (SEL) SWITCH, TACTILE (EQ3) SWITCH, TACTILE (SEEK +/>/M)
Remark
R926 R931 R932 R933 R937
1-216-805-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-811-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47 100 100 100 150
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
S912 S913 S913 S914 S914
1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31
SWITCH, TACTILE (SEEK –/./m) SWITCH, TACTILE (AF/TA) (R3000) SWITCH, TACTILE (SHUF) (R3000T) SWITCH, TACTILE (PTY) (R3000) SWITCH, TACTILE (REP) (R3000T)
R938 R941 R942 R945 R946
1-216-803-11 1-216-811-11 1-216-803-11 1-216-811-11 1-216-803-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
33 150 33 150 33
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
S915 S916 S917 S918 S918
1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31
SWITCH, TACTILE (SENS/BTM) SWITCH, TACTILE (6) SWITCH, TACTILE (5) SWITCH, TACTILE (4/SHUF) (R3000) SWITCH, TACTILE (4) (R3000T)
R949 R950 R951 R955 R956
1-216-809-11 1-216-809-11 1-216-809-11 1-216-813-11 1-216-811-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 220 150
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
S919 S919 S920 S921 S922
1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31
SWITCH, TACTILE (3/REP) (R3000) SWITCH, TACTILE (3) (R3000T) SWITCH, TACTILE (2) SWITCH, TACTILE (1) SWITCH, TACTILE (DSPL)
R957
1-216-805-11 METAL CHIP
47
5%
R957
1-216-817-11 METAL CHIP
470
5%
R961 R962 R963
1-216-815-11 METAL CHIP 1-216-809-11 METAL CHIP 1-216-809-11 METAL CHIP
330 100 100
5% 5% 5%
1/10W (R3000T) 1/10W (R3000) 1/10W 1/10W 1/10W
R971 R972 R974 R975 R977
1-216-817-11 1-216-817-11 1-216-817-11 1-216-845-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 470 470 100K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R978 R981 R982 R983 R984
1-216-817-11 1-216-817-11 1-216-817-11 1-216-817-11 1-216-817-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 470 470 470 470
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R985 R986 R987 R988 R989
1-216-817-11 1-216-817-11 1-216-811-11 1-216-811-11 1-216-811-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 470 150 150 150
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R991 R992 R993 R994 R995
1-216-864-11 1-216-840-11 1-216-857-11 1-216-821-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 39K 1M 1K 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R996 R997 R998
1-216-821-11 METAL CHIP 1-216-803-11 METAL CHIP 1-216-864-11 METAL CHIP
1K 33 0
5% 5% 5%
1/10W 1/10W 1/10W
S961 1-529-566-61 SWITCH, PUSH (1 KEY) (OPEN) ************************************************************* A-3283-384-A MAIN BOARD, COMPLETE (R3000) A-3283-388-A MAIN BOARD, COMPLETE (R3000T) ********************* 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-793-09 SCREW +PTT 2.6X8 (S) 7-685-795-09 SCREW +PTT 2.6X12 (S) < CAPACITOR > C1
1-162-964-11 CERAMIC CHIP
0.001uF
10%
C2
1-162-964-11 CERAMIC CHIP
0.001uF
10%
C3
1-126-963-11 ELECT
4.7uF
20%
C4 C5
1-126-947-11 ELECT 1-126-947-11 ELECT
47uF 47uF
20% 20%
50V (R3000) 50V (R3000) 50V (R3000) 16V 16V
C6 C7 C10 C11 C12
1-162-970-11 1-162-970-11 1-162-970-11 1-164-816-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.01uF 0.01uF 220PF 0.01uF
10% 10% 10% 2% 10%
25V 25V 25V 50V 25V
C13 C51
1-162-970-11 CERAMIC CHIP 1-126-947-11 ELECT
0.01uF 47uF
10% 20%
C53
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C54
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C55
1-107-826-11 CERAMIC CHIP
0.1uF
10%
25V 16V (R3000) 16V (R3000) 16V (R3000) 16V (R3000)
C56
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C57
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C58
1-107-826-11 CERAMIC CHIP
0.1uF
10%
< SWITCH > S900 S901 S902 S903 S904
1-786-653-11 1-786-653-11 1-771-884-31 1-771-884-31 1-771-884-31
SWITCH, TACTILE (EJECT (R)) SWITCH, TACTILE (EJECT (L)) SWITCH, TACTILE (OFF) SWITCH, TACTILE (SOURCE) SWITCH, TACTILE (– (VOLUME))
S905
1-771-884-31 SWITCH, TACTILE (ATT)
16V (R3000) 16V (R3000) 16V (R3000)
39
CDX-R3000/R3000T MAIN Ref. No.
Part No.
Description
Remark
C59
1-164-237-11 CERAMIC CHIP
16PF
5%
C60
1-164-237-11 CERAMIC CHIP
16PF
5%
C62
1-162-959-11 CERAMIC CHIP
330PF
5%
C301 C302
1-128-551-11 ELECT 1-128-551-11 ELECT
22uF 22uF
20% 20%
50V (R3000) 50V (R3000) 50V (R3000) 25V 25V
C303 C305 C306 C307 C308
1-128-551-11 1-104-665-11 1-164-816-11 1-164-816-11 1-164-816-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
22uF 100uF 220PF 220PF 220PF
20% 20% 2% 2% 2%
25V 10V 50V 50V 50V
C332 C333 C343 C401 C404
1-163-251-11 1-163-251-11 1-164-816-11 1-126-964-11 1-127-715-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
100PF 100PF 220PF 10uF 0.22uF
5% 5% 2% 20% 10%
50V 50V 50V 50V 16V
C405 C406 C407 C412 C413
1-127-715-11 1-126-960-11 1-126-960-11 1-126-947-11 1-162-970-11
CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP
0.22uF 1uF 1uF 47uF 0.01uF
10% 20% 20% 20% 10%
16V 50V 50V 16V 25V
C431 C432 C441 C442 C451
1-126-964-11 1-125-891-11 1-126-964-11 1-125-891-11 1-126-964-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT
10uF 0.47uF 10uF 0.47uF 10uF
20% 10% 20% 10% 20%
50V 10V 50V 10V 50V
C452 C461 C462 C471 C479
1-125-891-11 1-126-964-11 1-125-891-11 1-126-964-11 1-126-947-11
CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT
0.47uF 10uF 0.47uF 10uF 47uF
10% 20% 10% 20% 20%
10V 50V 10V 50V 16V
C481 C501 C502 C503 C504
1-126-964-11 1-162-970-11 1-162-964-11 1-104-665-11 1-162-970-11
ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
10uF 0.01uF 0.001uF 100uF 0.01uF
20% 10% 10% 20% 10%
50V 25V 50V 10V 25V
C507 C508 C509 C510 C511
1-162-917-11 1-162-917-11 1-162-966-11 1-162-970-11 1-126-964-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT
15PF 15PF 0.0022uF 0.01uF 10uF
5% 5% 10% 10% 20%
50V 50V 50V 25V 50V
C512 C513 C514 C515 C516
1-162-964-11 1-162-964-11 1-162-964-11 1-164-315-11 1-162-964-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 0.001uF 0.001uF 470PF 0.001uF
10% 10% 10% 5% 10%
50V 50V 50V 50V 50V (R3000)
C516
1-216-864-11 METAL CHIP
0
5%
C517 C518 C601 C602
1-107-826-11 1-125-891-11 1-131-868-81 1-165-319-11
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
0.1uF 0.47uF 3300uF 0.1uF
10% 10% 20%
1/10W (R3000T) 16V 10V 16V 50V
C617 C618 C621 C622
1-163-009-11 1-163-009-11 1-107-826-11 1-125-710-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP DOUBLE LAYERS
0.001uF 0.001uF 0.1uF 0.1F
10% 10% 10%
40
50V 50V 16V 5.5V
Ref. No.
Part No.
Description
C623 C631 C750 C751 C752
1-104-665-11 1-126-961-11 1-115-340-11 1-164-489-11 1-126-947-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT
100uF 2.2uF 0.22uF 0.22uF 47uF
20% 20% 10% 10% 20%
10V 50V 25V 16V 16V
Remark
C753 C754 C755 C756 C758
1-128-551-11 1-126-961-11 1-162-923-11 1-127-715-11 1-126-964-11
ELECT ELECT CERAMIC CHIP CERAMIC CHIP ELECT
22uF 2.2uF 47PF 0.22uF 10uF
20% 20% 5% 10% 20%
25V 50V 50V 16V 50V
C759 C760 C761 C763 C764
1-126-964-11 1-104-665-11 1-126-964-11 1-125-891-11 1-115-340-11
ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP
10uF 100uF 10uF 0.47uF 0.22uF
20% 20% 20% 10% 10%
50V 10V 50V 10V 25V
C765 C769 C770 C771
1-115-340-11 1-125-891-11 1-125-891-11 1-125-891-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.22uF 0.47uF 0.47uF 0.47uF
10% 10% 10% 10%
25V 10V 10V 10V
< CONNECTOR > CN601 1-774-701-21 PIN, CONNECTOR 16P CN701 1-794-311-21 PLUG, CONNECTOR 12P CNP301 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P < DIODE > D1 D479 D501 D502 D580
8-719-069-55 8-719-404-50 8-719-404-50 8-719-404-50 8-719-056-84
DIODE DIODE DIODE DIODE DIODE
UDZS-TE17-5.6B MA111-TX MA111-TX MA111-TX UDZ-TE-17-7.5B
D581 D601 D609 D651 D710
8-719-083-66 8-719-049-38 8-719-420-90 8-719-083-66 8-719-977-12
DIODE DIODE DIODE DIODE DIODE
UDZS-TE17-18B 1N5404TU MA8051-M UDZS-TE17-18B (R3000) DTZ6.8B
D711 D712 D715 D716 D717
8-719-977-12 8-719-977-12 8-719-422-76 8-719-977-12 8-719-977-12
DIODE DIODE DIODE DIODE DIODE
DTZ6.8B DTZ6.8B MA8075-M DTZ6.8B DTZ6.8B
D718 D719 D720 D751 D752
8-719-977-12 8-719-083-66 8-719-977-12 8-719-200-82 8-719-200-82
DIODE DIODE DIODE DIODE DIODE
DTZ6.8B UDZS-TE17-18B DTZ6.8B 11ES2 11ES2
D753 D754 D755 D756 D757
8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82
DIODE DIODE DIODE DIODE DIODE
11ES2 11ES2 11ES2 11ES2 11ES2
D758 D759 D760 D761 D762
8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82
DIODE DIODE DIODE DIODE DIODE
11ES2 11ES2 11ES2 11ES2 11ES2
CDX-R3000/R3000T MAIN Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
< IC > IC51 IC401 IC501 IC602 IC750
6-803-747-01 6-705-372-01 6-803-737-01 8-759-659-13 6-705-360-01
IC IC IC IC IC
Remark
< RESISTOR >
TDA7333-013TR (R3000) BD3808FS-FE2 MN101E01KDD PST3428UL TDA8588BJ/N2
< JACK > J1 J330 J561
Description
1-815-185-13 JACK (ANTENNA) 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR) 1-566-822-41 JACK (REMOTE IN) < JUMPER RESISTOR >
R1 R2 R3 R4 R5
1-216-821-11 1-216-809-11 1-216-809-11 1-216-839-11 1-216-843-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 100 100 33K 68K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R6
1-216-839-11 METAL CHIP
33K
5%
R7
1-216-843-11 METAL CHIP
68K
5%
R8
1-216-839-11 METAL CHIP
33K
5%
R9
1-216-843-11 METAL CHIP
68K
5%
1/10W (R3000) 1/10W (R3000) 1/10W (R3000) 1/10W (R3000) 1/10W
JC1 JC331 JC401 JC445 JC501
1-216-864-11 1-216-296-11 1-216-864-11 1-216-864-11 1-216-864-11
METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 0 0 0
5%
1/10W
R10
1-216-864-11 METAL CHIP
0
5%
5% 5% 5%
1/10W 1/10W 1/10W
R11 R29
1-216-864-11 METAL CHIP 1-216-809-11 METAL CHIP
0 100
5% 5%
JC503 JC681 JC753
1-216-864-11 METAL CHIP 1-216-864-11 METAL CHIP 1-216-296-11 SHORT CHIP
0 0 0
5% 5%
1/10W 1/10W
R51 R52 R53
1-414-595-11 INDUCTOR, FERRITE BEAD (R3000) 1-414-595-11 INDUCTOR, FERRITE BEAD (R3000) 1-216-801-11 METAL CHIP 22 5%
< COIL >
R54
1-216-833-11 METAL CHIP
10K
5%
R55
1-216-864-11 METAL CHIP
0
5%
R56 R57 R58
1-414-595-11 INDUCTOR, FERRITE BEAD (R3000) 1-414-595-11 INDUCTOR, FERRITE BEAD (R3000) 1-216-864-11 METAL CHIP 0 5%
R59
1-216-833-11 METAL CHIP
10K
5%
R60
1-216-833-11 METAL CHIP
10K
5%
R61
1-216-821-11 METAL CHIP
1K
5%
R301 R302
1-216-864-11 METAL CHIP 1-216-864-11 METAL CHIP
0 0
5% 5%
1/10W (R3000) 1/10W (R3000) 1/10W (R3000) 1/10W 1/10W
R405 R406 R407 R408 R409
1-218-881-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
27K 100 100 100 100
0.5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R410 R411 R431 R432 R433
1-216-809-11 1-216-809-11 1-216-809-11 1-216-841-11 1-216-864-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 47K 0
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R441 R442 R443 R451 R452
1-216-809-11 1-216-841-11 1-216-864-11 1-216-809-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 47K 0 100 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R453 R461 R462 R463 R471
1-216-864-11 1-216-809-11 1-216-841-11 1-216-864-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 100 47K 0 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R472
1-216-841-11 METAL CHIP
47K
5%
1/10W
L1 L301 L302 L303 L304
1-469-844-11 1-469-876-11 1-469-876-11 1-469-876-11 1-500-245-11
INDUCTOR 2.2uH INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD
L305 L306 L307 L561 L562
1-500-245-11 1-500-245-11 1-469-876-11 1-414-595-11 1-414-595-11
INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD
L563 L601
1-414-595-11 INDUCTOR, FERRITE BEAD 1-456-617-11 COIL, CHOKE 250uH
1/10W 1/10W (R3000)
1/10W (R3000) 1/10W (R3000) 1/10W (R3000)
1/10W (R3000)
< TRANSISTOR > Q1 Q22 Q51 Q52 Q431
8-729-106-68 1-801-806-11 8-729-026-49 8-729-027-43 6-550-752-01
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
2SD1615A-GP DTC144EKA (R3000) 2SA1037AK-T146-R (R3000) DTC114EKA-T146 (R3000) DTC614TKT146
Q441 Q451 Q461 Q471 Q478
6-550-752-01 6-550-752-01 6-550-752-01 6-550-752-01 8-729-027-43
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
DTC614TKT146 DTC614TKT146 DTC614TKT146 DTC614TKT146 DTC114EKA-T146
Q479 Q481 Q580 Q581 Q582
8-729-027-23 6-550-752-01 8-729-027-43 1-801-806-11 8-729-120-28
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
DTA114EKA-T146 DTC614TKT146 DTC114EKA-T146 DTC144EKA 2SC1623-L5L6
Q631 Q651 Q664
8-729-120-28 TRANSISTOR 2SC1623-L5L6 8-729-120-28 TRANSISTOR 2SC1623-L5L6 (R3000) 8-729-027-23 TRANSISTOR DTA114EKA-T146
41
CDX-R3000/R3000T MAIN Ref. No.
SENSOR Part No.
Description
R479 R481 R482 R501 R502
1-216-805-11 1-216-809-11 1-216-841-11 1-216-864-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47 100 47K 0 100
5% 5% 5% 5% 5%
Remark 1/10W 1/10W 1/10W 1/10W 1/10W
R503 R504 R505 R506 R507
1-216-809-11 1-218-871-11 1-218-871-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 10K 10K 100K 100K
5% 0.5% 0.5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R508 R509 R510 R511 R512
1-216-864-11 1-216-813-11 1-216-809-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 220 100 100 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R513 R514 R515 R516 R517
1-216-845-11 1-216-845-11 1-247-807-31 1-247-807-31 1-216-841-11
METAL CHIP METAL CHIP CARBON CARBON METAL CHIP
100K 100K 100 100 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/4W 1/4W 1/10W
R518 R521 R522 R523 R524
1-216-821-11 1-216-825-11 1-216-825-11 1-216-809-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 2.2K 2.2K 100 100
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R525 R526 R527 R528 R530
1-216-809-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 100 100K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R531 R532 R534 R535 R536
1-216-845-11 1-216-845-11 1-216-833-11 1-216-845-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 10K 100K 100K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R539
1-216-864-11 METAL CHIP
0
5%
R540 R541 R543 R544
1-216-845-11 1-216-845-11 1-216-845-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100K 100K 1K
5% 5% 5% 5%
1/10W (R3000) 1/10W 1/10W 1/10W 1/10W
R547 R549
1-216-864-11 METAL CHIP 1-216-845-11 METAL CHIP
0 100K
5% 5%
R550 R551
1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP
100K 100K
5% 5%
R552
1-216-845-11 METAL CHIP
100K
5%
R556
1-216-864-11 METAL CHIP
0
5%
R557 R558
1-216-809-11 METAL CHIP 1-216-864-11 METAL CHIP
100 0
5% 5%
R559 R560
1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP
100K 100K
5% 5%
R563 R564
1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP
100K 100K
5% 5%
R565
1-216-864-11 METAL CHIP
0
5%
Ref. No.
Part No.
Description
Remark
R566 R567 R568
1-216-864-11 METAL CHIP 1-216-864-11 METAL CHIP 1-216-864-11 METAL CHIP
0 0 0
5% 5% 5%
R569 R570
1-247-807-31 CARBON 1-249-413-11 CARBON
100 470
5% 5%
1/10W 1/10W 1/10W (R3000T) 1/4W 1/4W
R571 R572 R582 R583 R584
1-216-845-11 1-216-809-11 1-216-821-11 1-216-821-11 1-216-849-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 100 1K 1K 220K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R585 R609 R631 R632 R633
1-216-849-11 1-216-821-11 1-249-425-11 1-216-841-11 1-216-841-11
METAL CHIP METAL CHIP CARBON METAL CHIP METAL CHIP
220K 1K 4.7K 47K 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/4W 1/10W 1/10W
R634 R636 R651
1-216-829-11 METAL CHIP 1-216-845-11 METAL CHIP 1-216-821-11 METAL CHIP
4.7K 100K 1K
5% 5% 5%
R652
1-249-437-11 CARBON
47K
5%
R653
1-216-833-11 METAL CHIP
10K
5%
1/10W 1/10W 1/10W (R3000) 1/4W (R3000) 1/10W (R3000)
R654
1-216-833-11 METAL CHIP
10K
5%
R671 R672 R673 R674
1-216-809-11 1-216-809-11 1-218-871-11 1-216-845-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 10K 100K
5% 5% 0.5% 5%
1/10W (R3000) 1/10W 1/10W 1/10W 1/10W
R704 R705 R706 R752 R756
1-216-864-11 1-216-864-11 1-216-864-11 1-216-809-11 1-216-841-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
0 0 0 100 47K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
< SWITCH >
42
1/10W 1/10W (R3000) 1/10W 1/10W (R3000T) 1/10W 1/10W (R3000T) 1/10W 1/10W (R3000T) 1/10W 1/10W 1/10W 1/10W (R3000) 1/10W
S702
1-692-431-21 SWITCH, TACTILE (RESET) < TUNER >
TU1
A-3220-959-A TUNER UNIT (TUX-032//Q) < VIBRATOR >
X51 1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz) (R3000) X501 1-813-160-11 VIBRATOR, CERAMIC (27MHz) X502 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz) ************************************************************* SENSOR BOARD ************** < SWITCH > SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF) SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN) *************************************************************
CDX-R3000/R3000T SERVO Ref. No.
Part No.
Description
Remark
Ref. No. JR41 JR90 JR91
A-3283-339-A SERVO BOARD, COMPLETE **********************
Part No.
Description
Remark
1-414-760-21 FERRITE, EMI (SMD) 1-414-760-21 FERRITE, EMI (SMD) 1-414-760-21 FERRITE, EMI (SMD)
< CAPACITOR > < TRANSISTOR > C1 C2 C3 C5 C6
1-107-826-11 1-162-970-11 1-107-826-11 1-107-826-11 1-100-381-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP
0.1uF 0.01uF 0.1uF 0.1uF 10uF
10% 10% 10% 10% 20%
16V 25V 16V 16V 16V
C7 C8 C11 C13 C17
1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
10% 10% 10% 10% 10%
16V 16V 16V 16V 16V
C18 C19 C20 C21 C23
1-162-970-11 1-107-826-11 1-107-826-11 1-162-970-11 1-162-923-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.1uF 0.1uF 0.01uF 47PF
10% 10% 10% 10% 5%
25V 16V 16V 25V 50V
C25 C26 C27 C28 C29
1-162-908-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
3PF 0.1uF 0.1uF 0.1uF 0.1uF
0.25PF 10% 10% 10% 10%
50V 16V 16V 16V 16V
C30 C31 C32 C34 C35
1-162-921-11 1-162-925-11 1-107-826-11 1-107-826-11 1-162-970-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
33PF 68PF 0.1uF 0.1uF 0.01uF
5% 5% 10% 10% 10%
50V 50V 16V 16V 25V
C36 C37 C38 C39 C70
1-162-967-11 1-162-970-11 1-104-609-11 1-107-826-11 1-162-965-11
CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP
0.0033uF 0.01uF 100uF 0.1uF 0.0015uF
10% 10% 20% 10% 10%
50V 25V 4V 16V 50V
C71 C72 C73 C74 C75
1-162-965-11 1-162-962-11 1-162-962-11 1-107-826-11 1-107-826-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.0015uF 470PF 470PF 0.1uF 0.1uF
10% 10% 10% 10% 10%
50V 50V 50V 16V 16V
C76 C77 C78 C79
1-162-970-11 1-162-970-11 1-164-227-11 1-164-227-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.01uF 0.022uF 0.022uF
10% 10% 10% 10%
25V 25V 25V 25V
< CONNECTOR > CN1 CN2
IC1 IC2
6-703-699-01 IC uPD63712GC-8EU-A 6-705-002-01 IC BA5966FP-FE2 < FERRITE BEAD >
JR40
R1 R6 R7 R9 R11
1-216-841-11 1-216-833-11 1-216-840-11 1-216-822-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 10K 39K 1.2K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R12 R13 R14 R15 R41
1-216-809-11 1-216-833-11 1-216-797-11 1-216-797-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 10K 10 10 1K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R42 R44 R45 R70 R71
1-216-821-11 1-414-760-21 1-414-760-21 1-216-842-11 1-216-833-11
METAL CHIP 1K FERRITE, EMI (SMD) FERRITE, EMI (SMD) METAL CHIP 56K METAL CHIP 10K
5%
1/10W
5% 5%
1/10W 1/10W
R72 R73 R74 R75 R76
1-216-842-11 1-216-833-11 1-216-837-11 1-216-833-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
56K 10K 22K 10K 22K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R77 R78 R79 R80 R81
1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
10K 10K 10K 10K 10K
5% 5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W 1/10W
R82 R83 R84 R85
1-216-837-11 1-216-833-11 1-216-837-11 1-216-833-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 10K 22K 10K
5% 5% 5% 5%
1/10W 1/10W 1/10W 1/10W
< SWITCH > SW1
1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN) < VIBRATOR >
X1 1-795-562-21 VIBRATOR, CERAMIC (16.9344MHz) ************************************************************* MISCELLANEOUS *************** 7 7
1-414-760-21 FERRITE, EMI (SMD) < IC >
8-729-904-87 TRANSISTOR 2SB1197K-R < RESISTOR >
1-817-275-21 CONNECTOR, BOARD TO BOARD 28P 1-794-153-21 CONNECTOR, FPC (ZIF) 16P < FERRITE BEAD >
FB1
Q1
0 153 154 F901
1-776-206-21 CORD (WITH CONNECTOR) (POWER) (R3000T) 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER) (R3000) 8-820-207-02 OPTICAL PICK-UP KSS1000E/K1RP A-3372-448-A CHASSIS (OP) SUB ASSY (including M901) 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
M902 A-3372-447-A MOTOR ASSY, SL (SLED) M903 A-3372-443-A MOTOR ASSY, LE (LOADING) SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT) *************************************************************
1-414-760-21 FERRITE, EMI (SMD) The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
43
CDX-R3000/R3000T
Ref. No.
Part No.
Description
Remark
ACCESSORIES ************ 3-260-829-11 MANUAL, INSTRUCTION (ENGLISH,GERMAN, FRENCH,ITALIAN,DUTCH) (R3000) 3-260-838-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, GERMAN,FRENCH,ITALIAN,DUTCH) (R3000) 3-261-414-11 MANUAL, INSTRUCTION (ENGLISH, TRADITIONAL CHINESE) (R3000T) 3-261-419-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, TRADITIONAL CHINESE) (R3000T) 7-685-135-19 SCREW +P 2.6X10 TYPE2 NON-SLIT X-3383-264-2 CASE ASSY (for FRONT PANEL) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 301 302 303 304 305
X-3382-647-1 X-3382-926-1 3-349-410-11 X-3381-154-1 3-261-542-01
306 307 308
1-465-459-21 ADAPTOR, ANTENNA (R3000) 3-246-471-01 KEY (FRAME) 1-776-527-61 CORD (WITH CONNECTOR) (ISO) (POWER) (R3000) 1-776-206-21 CORD (WITH CONNECTOR) (POWER) (R3000T)
309
FRAME ASSY, FITTING SCREW ASSY (BS), FITTING (R3000) BUSHING SCREW ASSY (BS4), FITTING (R3000T) COLLAR
301
302 303
304 303
44
305
306
308
309
307
CDX-R3000/R3000T
MEMO
45
CDX-R3000/R3000T
REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. 1.0
46
Date 2003. 12
Description of Revision New
