Preview only show first 10 pages with watermark. For full document please download

Cdx-s2000/s2000s/sw200

Rating
Date

October 2018
Size

3.5MB
Views

7,180
Categories

Vehicles & accessories Motor vehicle electronics Car audio amplifiers

Transcript

CDX-S2000/S2000S/SW200 SERVICE MANUAL US Model CDX-S2000/SW200 Ver. 1.1 2006. 05 Canadian Model CDX-S2000 E Model CDX-S2000/S2000S • The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism NEW AUDIO POWER SPECIFICATIONS (US Model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 23.2 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 5% total harmonic distortion. CD Drive Mechanism Type MG-611XA-186//K Optical Pick-up Name KSS1000E SPECIFICATIONS CD player section Signal-to-noise ratio Frequency response Wow and flutter 120 dB 10 – 20,000 Hz Below measurable limit Tuner section FM Tuning range US, Canadian Model: 87.5 – 107.9 MHz E model: FM tuning interval: 50 kHz/200 kHz switchable 87.5 – 108 MHz (at 50 kHz step) 87.5 – 107.9 MHz (at 200 kHz step) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Usable sensitivity 9 dBf Selectivity 75 dB at 400 kHz Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz 0.5% (stereo), 0.3% (mono) Separation 35 dB at 1 kHz Frequency response 30 – 15,000 Hz AM Tuning range US, Canadian Model: 530 – 1,710 kHz E Model: AM tuning interval: 9 kHz/10 kHz switchable 531 – 1,602 kHz (at 9 kHz step) 530 – 1,710 kHz (at 10 kHz step) Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV Power amplifier section Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 – 8 ohms Maximum power output 52 W × 4 (at 4 ohms) General Outputs Inputs Tone controls Audio outputs terminal (rear) Power antenna relay control terminal Power amplifier control terminal Antenna input terminal Low: ±10 dB at 60 Hz (XPLOD) Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz (XPLOD) – Continued on next page – FM/AM COMPACT DISC PLAYER 9-961-387-02 Sony Corporation 2006E04-1 © 2006. 05 eVehicle Division Published by Sony Techno Create Corporation 1 CDX-S2000/S2000S/SW200 Power requirements Dimensions Mounting dimensions Mass Supplied accessories 12 V DC car battery (negative ground) Approx. 178 × 50 × 176 mm (7 1/8 × 2 × 7 in.) (w/h/d) Approx. 182 × 53 × 161 mm (7 1/4 × 2 1/8 × 6 3/8 in.) (w/h/d) Approx. 1.2 kg (2 lb. 10 oz.) Parts for installation and connections (1 set) Front panel case (1) Design and specifications are subject to change without notice. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block. optical pick-up SERVICE NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. semi-fixed resistor • E model Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. TEST DISCS This set can playback CD-R and CD-ROM discs. The following test discs should be used to check the capability: This label is located on the bottom of the chassis. CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) CD-RW test disc TCD-W082L (Part No. J-2502-063-2) SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. 2 CDX-S2000/S2000S/SW200 Notes on CD-Rs (recordable CDs)/CD-RWs (rewritable CDs) This unit can play the following discs: Type of discs Label on the disc z UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Audio CD MP3 files • Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. • You cannot play a CD-R/CD-RW that is not finalized∗. • You can play MP3 files recorded on CD-ROMs, CD-Rs, and CD-RWs. • A CD-R/CD-RW to which a session can be added can be played. Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. ∗ A process necessary for a recorded CD-R/CD-RW disc to be played on the audio CD player. EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CN751) and the SERVO board (CN1) with the extension cable (Part No. J-2502-076-1). MAIN BOARD CN751 J-2502-076-1 SERVO BOARD CN1 3 CDX-S2000/S2000S/SW200 TABLE OF CONTENTS 1. GENERAL Location of Controls (US, Canadian Model) .......................... 5 Location of Controls (E Model) .............................................. 5 Connections (US, Canadian Model) ........................................ 6 Connections (E Model) ........................................................... 7 2. DISASSEMBLY 2-1. Sub Panel (1) Assy .............................................................. 9 2-2. CD Mechanism Block ......................................................... 9 2-3. Main Board ....................................................................... 10 2-4. Chassis (T) Sub Assy ........................................................ 10 2-5. Roller Arm Assy ................................................................ 11 2-6. Chassis (OP) Assy ............................................................. 11 2-7. Optical Pick-up ................................................................. 12 2-8. SL Motor Assy (M902) ..................................................... 12 2-9. LE Motor Assy (M903) ..................................................... 13 2-10. Servo Board ....................................................................... 13 3. DIAGRAMS 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. IC Pin Descriptions ........................................................... 14 Block Diagram –CD Section– ........................................... 18 Block Diagram –Main Section– ........................................ 19 Block Diagram –Display Section– .................................... 20 Circuit Boards Location .................................................... 20 Note for Printed Wiring Boards and Schematic Diagrams .......................................................... 21 3-7. Waveforms ......................................................................... 21 3-8. Printed Wiring Boards –CD Mechanism Section– ............ 22 3-9. Schematic Diagram –CD Mechanism Section– ................ 23 3-10. Schematic Diagram –Main Section (1/2)– ........................ 24 3-11. Schematic Diagram –Main Section (2/2)– ........................ 25 3-12. Printed Wiring Boards –Main Section– ............................ 26 3-13. Printed Wiring Board –Display Section– .......................... 27 3-14. Schematic Diagram –Display Section– ............................. 28 3-15. IC Block Diagrams ............................................................ 29 4. EXPLODED VIEWS 4-1. 4-2. 4-3. 4-4. 4-5. 4-6. Main Section ..................................................................... 31 Front Panel Section ........................................................... 32 CD Mechanism Section (1) ............................................... 33 CD Mechanism Section (2) ............................................... 34 CD Mechanism Section (3) ............................................... 35 CD Mechanism Section (4) ............................................... 36 5. ELECTRICAL PARTS LIST ........................................ 37 4 CDX-S2000/S2000S/SW200 SECTION 1 GENERAL (US, Canadian Model) This section is extracted from instruction manual. (E Model) 5 CDX-S2000/S2000S/SW200 Connections (US, Canadian Model) 6 CDX-S2000/S2000S/SW200 Connections (E Model) 7 CDX-S2000/S2000S/SW200 SECTION 2 DISASSEMBLY Note : This set can be disassemble according to the following sequence. SET 2-1. SUB PANEL (1) ASSY (Page 9) 2-2. CD MECHANISM BLOCK (Page 9) 2-3. MAIN BOARD (Page 10) 2-7. 8 2-4. CHASSIS (T) SUB ASSY (Page 10) 2-5. ROLLER ARM ASSY (Page 11) 2-10. SERVO BOARD (Page 13) 2-6. CHASSIS (OP) ASSY (Page 11) 2-8. SL MOTOR ASSY (M902) (Page 12) OPTICAL PICK-UP (Page 12) 2-9. LE MOTOR ASSY (M903) (Page 13) CDX-S2000/S2000S/SW200 Note : Follow the disassembly procedure in the numerical order given. 2-1. SUB PANEL (1) ASSY 3 two claws 2 two claws 1 two screws (+PTT 2.6 x 6) 4 sub panel (1) assy 2-2. CD MECHANISM BLOCK 7 bracket (CD) 5 CD mechanism block 6 two screws (+PTT 2.6 x 6) 2 screw (+PTT 2.6 x 6) 3 1 screw (+PTT 2.6 x 6) 4 CN751 9 CDX-S2000/S2000S/SW200 2-3. MAIN BOARD 1 three screws (+BTT) 2 two screws (+PTT 2.6 x 8) 3 MAIN board 2-4. CHASSIS (T) SUB ASSY 4 claw 2 two screws (+P 1.7 x 2.2) 1 two screws (+P 1.7 x 2.2) 6 chassis (T) sub assy 5 SENSOR board 3 claw 10 CDX-S2000/S2000S/SW200 2-5. ROLLER ARM ASSY 3 washer (1.0 – 2.5) 5 roller arm assy 4 worm wheel (RA) 2 spring (RAR) 1 spring (RAL) 2-6. CHASSIS (OP) ASSY 8 qa chassis (OP) assy 0 compression spring (damper) lever (D) 4 washer 1 CN2 6 9 two compression springs (damper) 5 gear (LE1) 7 slider (R) 3 tension coil spring (KF) 2 Remove the six solderings. 11 CDX-S2000/S2000S/SW200 2-7. OPTICAL PICK-UP 2 chucking arm sub assy 5 claw 1 tension coil spring (CHKG) 7 optical pick-up 6 main shaft 4 rack (SL) 3 screw (+B 1.4 x 5) 2-8. SL MOTOR ASSY (M902) 1 screw (+P 1.4 x 1.8) 2 SL motor assy (M902) 12 CDX-S2000/S2000S/SW200 2-9. LE MOTOR ASSY (M903) 8 screw (+M 1.7 x 2.5) 0 woam (LEB) assy 9 bearing (LEB) qf two toothed lock screws (+M 1.4 ) 2 washer qa screw (+M 1.7 x 2.5) 3 gear (LE1) lever (D) 4 bracket (LEM) qs screw (+M 1.7 x 2.5) qd qg LE motor assy (M903) 5 6 screw (+P 1.7 x 2.2) slider (R) 7 leaf spring (LE) 1 Remove the soldering. 2-10. SERVO BOARD 1 Remove the eight solderings. 6 SERVO board 2 Remove the three solderings. 4 toothed lock screw (M 1.7) 5 claw 3 CN2 13 CDX-S2000/S2000S/SW200 SECTION 3 DIAGRAMS 3-1. IC PIN DESCRIPTIONS • IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD) Pin No. Pin Name I/O Pin Description 1 LD O Laser diode ON/OFF control signal output (L: laser OFF, H: laser ON) 14 2 3 PD PN I I Dimmer monitor input from optical pick-up laser diode. Not used. (Fixed at L in this set) 4 5 AVDD DGND — — Analog power supply pin (+3.3 V) Ground 6 7 RFOK INTQ O O RFOK signal output to system control IC. CD text pack synchronization signal output to system control IC. 8 RST I 9 A0 I CD reset signal input from system control IC. Command/parameter discrimination signal input from system control IC. 10 STB I (L: command transmission, H: parameter transmission) Data strobe signal input from system control IC. 11 12 SCK SO I O Serial clock input from system control IC. Serial data output to system control IC. 13 14 SI DVDD I — Serial data input from system control IC. Power supply pin (+3.3 V) 15 16 DAVDD ROUT — O D/A converter power supply (+) pin (+3.3 V) Analog audio signal output (R-ch) 17 18 DAGND REGC — — Ground Capacitor connection pin for SCF regulator. 19 20 DAGND LOUT — O Ground Analog audio signal output (L-ch) 21 22 23 DAVDD XVDD XTAL — — O D/A converter power supply (+) pin (+3.3 V) Power supply pin (+3.3 V) Main system clock output (16.9344 MHz) 24 25 XTAL XGND I — Main system clock input (16.9344 MHz) Ground 26 27 DVDD C1D1/FZD — O Power supply pin (+3.3 V) Not used. (Open) 28 29 C1D2/TZD C2D1/RMUTE O O Not used. (Open) CD R-ch data zero detection signal output 30 31 C2D2/LMUTE C2D3/SHOCK/SBSY O O CD L-ch data zero detection signal output Not used. (Open) 32 33 LOCK/FR WFCK/MIRR O O Not used. (Open) Not used. (Open) 34 35 RFCK/HOLD PLCK O O Not used. (Open) Not used. (Open) 36 37 C16M DGND O — Not used. (Open) Ground 38 39 TX EMPH/RAMOVER O O Not used. (Open) Not used. (Open) 40 41 FLAG DVDD O — Not used. (Open) Power supply pin (+3.3 V) 42 LIMIT I 43 XTALEN I 44 DGND — (Fixed at L in this set) Ground 45 46 DIN DOUT I O Not used. (Connect to DOUT in this set) Not used. (Connect to DIN in this set) 47 48 SCKIN SCKO I O Not used. (Connect to SCKO in this set) Not used. (Connect to SCKIN in this set) 49 LRCKIN I Not used. (Connect to LRCK in this set) Not used. (Fixed at L in this set) Oscillation circuit ON/OFF control signal input (L: ON, H: OFF) CDX-S2000/S2000S/SW200 Pin No. 50 Pin Name LRCK I/O O Pin Description Not used. (Connect to LRCKIN in this set) 51 52 DVDD FD+ — O Power supply pin (+3.3 V) Focus servo drive PWM signal output (+) 53 54 FD– TD+ O O Focus servo drive PWM signal output (–) Tracking servo drive PWM signal output (+) 55 56 TD– SD+ O O Tracking servo drive PWM signal output (–) Sled servo drive PWM signal output (+) 57 58 SD– MD+ O O Sled servo drive PWM signal output (–) Spindle servo drive PWM signal output (+) 59 60 MD– DGND O — Spindle servo drive PWM signal output (–) Ground 61 62 to 66 TESTEN TEST4 to TEST0 I I 67 68 ADGND EFM — O A/D converter power supply (–) pin EFM signal output 69 70 ASY ADVDD I — EFM comparator reference voltage input A/D converter power supply pin (+3.3 V) 71 72 RFI EQ2 I — RF signal input for EFM data growing. Not used. (Open) 73 74 EQ1 RF– — I RF amplifier equalizer parts connection pin Not used. (Open) 75 76 RF2– AGCO I O RF amplifier inversion input RF signal output after on AGC. 77 78 79 AGCI RFO ATEST I O I RF AGC signal amplifier input RF signal output before on AGC. Not used. (Open) 80 81 C3T AGND — — Capacitor connection pin for 3T detection. Ground 82 83 A C I I Signal input (A) from optical pick-up detector. Signal input (C) from optical pick-up detector. 84 85 B D I I Signal input (B) from optical pick-up detector. Signal input (D) from optical pick-up detector. 86 87 F E I I Signal input (F) from optical pick-up detector. Signal input (E) from optical pick-up detector. 88 89 VREFIN AVDD I — Reference voltage (+1.65 V) input Analog power supply pin (+3.3 V) 90 91 REFOUT REFC O — Reference voltage (+1.65 V) output Capacitor connection pin for reference voltage output. 92 93 FE– FEO I O Focus error signal amplifier inversion input Focus error signal amplifier output 94 95 ADCIN TE- I I Not used. (Open) Tracking error signal amplifier inversion input 96 97 TEO TE2 O O Tracking error signal amplifier before output Tracking error signal amplifier after output 98 99 TEC AGND I — Tracking error signal comparator input Ground 100 PWMSW I Test setting input (Fixed at L in this set) Test setting input (Fixed at L in this set) Not used. (Fixed at L in this set) 15 CDX-S2000/S2000S/SW200 • IC801 MB90473PF-G166-BNDE1 (SYSTEM CONTROL) (MAIN BOARD (2/2)) Pin No. Pin Name I/O Pin Description 1 ATT O Audio mute control signal output 2 to 4 5 NC BEEP — O Not used in this set. (Open) Beep signal output to power amp IC 6 7 to 10 VOL ATT NC O — Electrical volume ATT control output Not used in this set. (Open) 11 12 to 14 VSS NC — — Ground pin Not used in this set. (Open) 15 16, 17 TU ATT NC O — Tuner mute control output Not used in this set. (Open) 18 19 CD SI CD SO I O CD servo serial data signal input CD servo serial data signal output 20 21 CD SCK RE 0 O O CD servo serial clock signal output Not used in this set. (Open) 22 23 RE 1 VCC+3.3 O — Not used in this set. (Open) Power supply pin (+3.3 V) 24 25 EEP SIO EEP SCK I/O O Serial data signal input/output for EEPROM comunication Serial clock signal output for EEPROM comunication 26 SHUT SW I Shutter switch open/close detect signal input Not used in this set. (Open) “L”: Panel open, “H”: Panel close 27 28 LCD CE LCD SO O O Chip enable signal output to LCD driver IC Serial data signal output to LCD driver IC Flash: UART serial out 29 30 LCD SCK NC O — Serial clock signal output to LCD driver IC Not used in this set. (Open) 31 32 33 STB AUX IIC SCK O — O Standby signal output to power amp IC Not used in this set. (Open) IIC bus serial clock signal output 34 35 IIC SIO VCC+3.3 I/O — IIC bus serial data signal input/output Power supply pin (+3.3 V) (for A/D converter) 36 37 AVRH+3.3 AVSS — — External reference power supply (+3.3 V) (for A/D converter) Ground pin (for A/D converter) 38, 39 40 KEY IN0, 1 NC I — Key signal input Not used in this set. (Open) 41 42 RC IN0 VSS I — Rotary commander key signal input Ground pin 43, 44 45 NC VSM — I Not used in this set. (Fixed at “L”.) S meter voltage detect signal input 46 47 DST SEL KEY ACK I I 48 49, 50 NC MD0, 1 — I Not used in this set. (Open) Input for operation mode designation (Fixed at “H”.) 51 52 MD2 NC I — Input for operation mode designation (Fixed at “L”.) Not used in this set. (Open) 53 54 BU IN OP REQ/INTQ I O Back up power supply detect signal input OP REQ/INTQ select signal output 55 56 CD SELFSW DIAG I I CD mechanism self load position detect switch signal input Condition input from power amp IC 57 58 TU ATT IN UNI SI I I Tuner ATT signal input Not used in this set. (Open) Serial data signal input Not used in this set. (Open) 59 60 UNI SO UNI SCK O O Serial data signal output Not used in this set. (Open) Serial clock signal output Not used in this set. (Open) 61 62 BUS ON SYS RST O O Bus on signal output System reset signal output 16 Destination select pin Key acknowledge detect signal input CDX-S2000/S2000S/SW200 Pin No. 63 Pin Name TEL ATT I/O O Pin Description TEL ATT signal output Not used in this set. (Open) 64 65 ACC IN SIRCS I I Accessory power supply detect signal input Remote control signal (infrared rays) input 66 67 RAM BU TEST IN O I Not used in this set. (Fixed at “L”.) Test mode detect signal input 68 FLASH W I Memory mode changeover signal input Normally “H” input (single chip mode) 69 70, 71 NOSE SW NC O — 72 DOOR SW I Front panel open/close detect signal input “L” input: Panel close, “H” input: Panel open 73 74 DOOR IND RC IN1 O I Not used in this set. (Open) Rotary commander shift key signal input 75 76 XKEY ON NC O — Key power supply control signal output Not used in this set. (Open) 77 78 RESET NC I — Reset signal input Not used in this set. (Open) 79 80 X1A X0A — — Oscillator connect pin (32 kHz) Oscillator connect pin (32 kHz) 81 82 VSS X0 — — Ground pin Oscillator connect pin (3.68 MHz) 83 84 X1 VCC+3.3 — — Oscillator connect pin (3.68 MHz) Power supply pin (+3.3 V) 85 to 88 89 90 NC ZERO DET R ZERO DET L — I I Not used in this set. (Open) Mechanism deck mute zero closs detect signal input R Mechanism deck mute zero closs detect signal input L 91 92 CD STB CD IN SW O I CD servo data strob signal output Timing of data latch: “L” output CD mechanism IN-SW detect signal input 93 94 CD LOAD CD ON/EJECT O O CD mechanism loading motor control signal output CD mechanism eject motor control signal output 95 96 CDM ON/D SW CD LIMIT I I CD mechanism DSW detect signal input CD mechanism IN-LIMIT SW signal input 97 98 RFOK CD XRST I O CD servo RFOK signal input CD servo reset signal output 99 CD A0 O CD servo command/parameter identification signal output Command transmission: “L” output, parameter transmission: “H” output 100 NC — Not used in this set. (Open) “L” after reset: Flash write mode Not used in this set. (Fixed at “H”.) Not used in this set. (Open) Pin rj (KEY ACK) active: “L” output 17 17 CDX-S2000/S2000S/SW200 3-2. BLOCK DIAGRAM — CD SECTION — • R-ch is omitted due to same as L-ch. • Siganal Path : CD PLAY DETECTOR PD1 PD1 PD2 82 A PD2 77 AGCI RFO 78 AGCO 76 71 RFI EFM 68 69 ASY ROUT 16 84 B CD-L LOUT 20 I-V AMP RF AMP,DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR IC1 E E F F 87 E FEO 93 92 FE– 86 F TEO 96 95 TE– TE2 97 LD AUTOMATIC POWER CONTROL Q1 1 LD 89 ZERO DET R 18 CD_SI 19 CD_SO 20 CD_SCK RFOK 6 INTQ 7 STB 10 A0 9 RST 8 PD 2 PD 97 54 91 99 98 RF_OK OP INTQ CD_STB CD_A0 CD XRST SYSTEM CONTROL IC801 (1/3) OPTICAL PICK-UP BLOCK (KSS-1000E) 2-AXIS DEVICE 90 ZERO DET L SO 12 SI 13 SCK 11 LD PD LMUTE 30 RMUTE 29 98 TEC LASER DIODE FOCUS/TRACKING COIL DRIVE, SLED/SPINDLE/LOADING MOTOR DRIVE IC2 XTAL 23 FCS+ FCS– 11 VO2– OPIN2+ 5 52 FD+ 12 VO2+ OPIN2– 6 53 FD– 13 VO1– OPIN1+ 2 54 TD+ 14 VO1+ OPIN1– 3 55 TD– X1 16.934MHz XTAL 24 (FOCUS) (TRACKING) TRK+ TRK– SW1 (DOWN) SW2 (SELF) M902 (SLED) M M901 (SPINDLE) M M903 (LOADING) M 95 CD_DSW 55 CD_SELFSW 15 VO4+ OPIN4+ 27 56 SD+ 16 VO4– OPIN4– 26 57 SD– SW3 (DISC IN) 92 CD_INSW SW4 (LIMIT) 96 CD_LIMIT 17 VO3+ OPIN3+ 24 58 MD+ 18 VO3– OPIN3– 23 59 MD– 10 VOL+ FWD 1 93 CD LOAD 9 VOL– REV 28 94 CD ON/EJECT 18 18 MAIN SECTION (Page 19) R-CH 83 C 85 D A CDX-S2000/S2000S/SW200 3-3. BLOCK DIAGRAM — MAIN SECTION — ELECTRONIC VOLUME IC401 CD SECTION A CD-L R-CH (Page 18) 9 C2 8 C1 PJ401 OUTS1 17 OUTS2 18 L R-CH 1 ANT R L 4 R 3 POWER AMP IC100 7 B2 6 B1 OUTF2 23 12 INRR(FL) OUTR2 22 OUTF1 25 OUTR1 24 VCC 10 TU VDD 11 E2P VDD 15 TU-SCL 13 TU-SDA 14 REAR AUDIO OUT MUTE Q407 TUX601 (TUNER UNIT) PJ601 (ANTENNA) R-CH 11 INRF(RL) R-CH (FRONT) R-CH (REAR) MUTE Q405 CNP901 1 FL+ 9 FL- PR+ 5 PR- 3 2 RF+ 9 RF- 7 MUTE Q404 10 MUTE 29 AU+8V TU+5V U COM+3.3V SCL 30 SDA 31 SCL SDA MUTE CONTROL Q400,401 D400 R-CH IIC SCK 33 IIC SIO 34 45 VSM 15 TU ATT E2P SCL 16 E2P SDA 17 25 EEP SCK 24 EEP SIO 5 SW1 29 SW2 27 SYSTEM CONTROL IC801 (2/3) S-METER 6 TU MUTE 7 4 FR+ 12 FR3 RR+ 11 RR- BATT SCL SDA 6 F901 SDA SCL SCL SDA 2 SDA 4 SCL BATT RL+ RL- AMP-REM ANT-REM 16 VOL ATT 6 ATT BEEP STB DIAG 1 5 31 56 16 ACGND 22 STB 25 DIAG BATT REG1 REG2 REG3 REG4 REG5 30 37 31 33 34 AU+8V U-COM+3.3V SERVO+3.3V MECHA+6V DISP+B 35 VP ACC CHECK Q900 ACC IN 64 15 TEST IN 67 BU IN 53 7 BATTERY CHECK Q902,906,907 D912 BATT TU+5V TU+5V REG Q601 • R-CH is omitted due to same as L-CH. • Signal Path : CD PLAY : FM : AM 19 19 AU+8V ACC TEST CDX-S2000/S2000S/SW200 3-4. BLOCK DIAGRAM — DISPLAY SECTION — SYSTEM CONTROL IC801 (3/3) 3-5. CIRCUIT BOARDS LOCATION LCD DRIVER IC901 SERVO board SENSOR board KEY MATRIX LSW905-911,913, 914,916-920, S901-906 38 KEYIN0 39 KEYIN1 D801 KEY ACKNOWLEDGE SWITCH Q800 SPEAKER board LCD SO 28 LCD SCK 29 LCD CE 27 64 DI CLK 63 CL 62 CE LCD901 SEG4 4 | | SEG49 49 LIQUID CRYSTAL DISPLAY PANEL COM4 51 | | COM1 54 47 KEY ACK DIMMER LED910,911 (BACKLCDLIGHT) 75 XKEY ON tuner unit (TUX601) DISP+B E model ( S800 FREQUENCY SELECT 46 DST SEL 9K ) 10K 2 IN +3.3V REG IC905 REMOTE CONTROL SIGNAL RECEIVER IC951 RESET IC802 U COM+3.3V DISPLAY board LED901,902,904-909, LSW905-911,913,914, 916-920 US,Canadian model OUT 1 77 RESET SIRCS 65 S802 RESET X801 32.768kHz 3 V OUT 1 VCC 79 X1A 80 X0A X0 82 X1 83 2 OUT VDD 2 CE 4 DISP+B IR X800 3.68MHz 20 20 MAIN board CDX-S2000/S2000S/SW200 Ver. 1.1 3-6. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 3-7. WAVEFORMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) — Servo Board — 1 For schematic diagrams. For printed wiring boards. Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. f : internal component. • • C : panel designation. Note: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. a : Through hole. • • : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • • • • • • • • • • • Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. A : B+ Line. B : B– Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. CD mechanism section no mark : CD PLAY Main (1/2), (2/2) and Display sections no mark : FM ( ) : AM < > : CD PLAY ∗ : Impossible to measure Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD PLAY F : FM f : AM Abbreviation CND : Canadian model. — Main Board — (MODE: CD PLAY) Caution: Pattern face side: (Side B) Parts face side: (Side A) 1 1.2Vp-p 16.9344MHz IC1 wd 32.768kHz (XTAL) IC801 2 i; (X0A) 2 0.85V to 1.45Vp-p Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. 2.4Vp-p 3.68MHz IC1 uj IC801 (AGCI) 3 C Q 1.7Vp-p 0V These are omitted Approx. 620mVp-p B E IC1 od (FEO) 4 0V BE C These are omitted Approx. 200mVp-p IC1 ECB These are omitted • Abbreviation CND : Canadian model. 21 21 oh (TEO) is (X0) CDX-S2000/S2000S/SW200 3-8. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 20 for Circuit Boards Location. 2 1 3 4 5 6 7 : Uses unleaded solder. 8 9 10 11 12 13 14 A C11 C1 C32 C2 C29 C31 JR90 R45 C7 C30 X1 JR91 B R44 R42 C5 R41 C8 C3 C6 C28 C13 R11 C38 R13 C36 R1 C27 R14 CN1 (Page 26) 2 C34 C79 R85 R84 C71 C70 C74 C73 IC2 R82 R80 R81 R78 R79 C72 R75 SW3 R83 C76 C77 C78 F C75 R77 R76 R74 R73 R71 E R72 R70 FB1 R9 C19 C18 CN D R12 C35 R15 C39 C37 C25 C23 C17 JR41 R6 R7 C20 C21 Q1 C26 JR40 C IC1 SW2 SW1 1-688-822- G 22 22 CDX-S2000/S2000S/SW200 • Refer to page 21 for Waveforms. 3-9. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 29 for IC Block Diagram. C20 R9 C25 Q1 R13 TP32 C23 R7 C21 C19 TP19 CN2 C18 C17 R6 TP33 R14 R15 C36 TP31 C38 TP20 C37 TP30 TP29 TP14 R12 C26 C39 TP21 C35 C27 TP28 TP27 C34 R1 TP26 TP13 TP12 R11 IC1 C28 TP11 TP22 C29 C13 TP10 TP9 TP23 TP8 TP7 C30 TP24 TP6 TP5 TP4 TP25 C31 TP3 SW4 TP2 TP81 TP80 C32 TP1 CN1 C11 JR90 JR91 TP65 TP64 M901 TP85 TP83 TP84 M902 C1 TP82 C5 C3 R45 R44 X1 C8 C6 TP28 TP88 TP29 TP89 SW3 TP58 TP57 TP54 TP48 C7 TP87 TP61 TP60 TP59 TP56 TP55 FB1 C2 TP27 TP63 TP62 R41 JR41 JR40 TP52 TP51 TP53 R42 TP49 TP50 SW2 TP47 TP46 TP45 TP44 SW1 TP43 TP42 TP41 TP90 TP91 TP40 R70 R71 C70 R72 R73 C71 R74 R75 R76 R77 IC B/D IC2 C79 R85 R84 C78 R83 R82 C72 C77 R81 R80 C73 C76 R79 R78 TP100 C74 TP75 M903 TP92 TP93 TP74 TP71 TP70 TP73 TP72 C75 23 23 (Page 25) CDX-S2000/S2000S/SW200 3-10. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 30 for IC Block Diagram. TUX601 R607 R604 R603 R606 R608 C600 PJ601 PJ401 C435 C436 JR10 C303 C108 IC100 IC B/D C424 R416 C113 C440 R431 R421 IC401 Q405 JR103 R401 C425 R414 R407 R400 D921 C438 R429 R419 R406 R405 C410 D907 D908 R409 C408 C411 C444 R432 D909 D917 D916 C409 C107 R420 R415 D905 D906 C426 D904 R412 R411 C414 D903 D902 C101 Q404 Q403 D922 Q402 R404 C400 R418 C428 R417 JR6 R435 C437 R427 R436 C452 R440 R442 C453 R441 CNP901 L400 R443 C416 Q601 C417 Q406 Q407 C106 L602 R615 C621 C618 Q401 C619 C620 D600 D400 Q400 C111 R931 R424 C109 C430 R932 R913 D914 F901 L900 C922 Q900 R903 R902 (Page 25) 24 24 C908 R904 D919 CDX-S2000/S2000S/SW200 3-11. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 21 for Waveforms. (Page 24) C447 CN751 R841 R828 R823 R822 R830 R821 R839 R840 R447 C802 D702 C446 R837 C809 C801 C441 C810 R448 C709 C707 R834 R832 C823 C824 R708 R709 R819 R805 R818 R838 R806 R707 R703 C813 R705 C821 R846 R801 R804 JR11 C705 R847 R850 IC801 L702 (Page 23) C701 R815 C807 R810 R826 R811 L701 L700 C822 S800 C704 C825 JR5 R800 R936 R722 C820 R853 R808 R809 C818 X800 R843 R802 R851 IC802 R854 X801 C816 C817 R845 R835 C812 R852 CNP800 R860 R873 R848 R849 D801 R844 R925 R833 (Page 28) R901 R814 Q800 R927 D808 R437 C815 D811 D814 D813 D812 D815 D816 D817 R825 S802 R824 R917 R928 D915 Q906 D912 C706 Q907 25 25 C909 R912 Q902 CDX-S2000/S2000S/SW200 3-12. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 20 for Circuit Boards Location. 1 2 3 4 5 6 : Uses unleaded solder. 7 8 9 10 11 12 13 14 15 PJ401 A PJ601 R421 JW111 R418 D902 C113 R443 R427 F901 JW110 R442 C108 JW112 JW113 B D903 CNP901 C435 C436 C303 IC100 C437 JW108 JW109 D917 JW106 JW124 JW97 D908 D906 D904 JW125 D907 C106 Q402 R931 D909 JR6 JW127 JW128 R913 JW107 D905 C444 JW98 D916 Q406 JW5 JW6 R431 R429 JW126 Q405 R420 Q404 C C438 R441 R419 Q407 C440 JW123 JW96 D914 R932 JW100 R432 JW99 JW95 D922 JW121 D D921 C922 Q403 C600 Q401 C101 D400 C430 JW101 R917 R912 Q902 JW86 L701 L702 R810 JW11 X801 R873 R844 JW8 R925 Q900 R848 C908 R902 R903 C825 R822 R824 R825 JW78 R847 R851 JW33 R828 R823 JW9 JW49 R852 JW12 C812 C813 R814 R805 R850 S802 R437 D808 C815 CNP800 (Page 27) 26 26 JW1 JW2 JW13 JW14 JW16 JW17 JW18 JW23 JW24 JW25 Q800 JW19 R849 JW20 R804 JW21 JW22 R826 JW71 JW26 JW29 JW31 JW30 D801 C706 C821 JW27 R809 R806 C823 JW137 JW32 R845 C807 R801 JW28 R860 JW139 R818 R834 IC802 R832 JW15 JW39 R821 JW37 JW36 JW38 JW40 D811 D812 D813 D814 D816 D815 TP001 FMB3 C817 C816 JW41 JW42 R819 C820 JR5 R901 R904 R835 JR11 1 D817 R703 JW7 X800 C818 R854 JW80 R709 80 JW43 JW34 JW35 R815 R830 JW136 JW3 • Semiconductor Location C822 C824 JW4 Q906 C705 JW79 R843 R722 R802 R708 R846 R705 R841 R839 R840 D702 R936 FMB4 (Page 22) D912 JW81 R853 R833 JW200 D915 JW85 R838 R707 IC JW46 JW102 JW103 JW91 C701 C707 JW70 JW69 JW68 JW135 C414 R808 JW45 C704 C802 C801 C410 C411 JR103 JW62 JW44 JW203 JW201 R811 JW10 R800 I JW204 JW202 Q907 C709 IC401 C409 JW56 JW65 S800 JW207 JW205 JW84 JW67 JW57 JW53 JW55 JW52 JW72 JW48 H CN751 JW143 C810 JW64 JW47 JW54 C408 JW50 JR10 JW51 R607 TUX601 JW73 R400 R608 JW88 JW76 JW74 JW63 R412 JW104 JW105 C109 C809 JW140 JW141 JW142 C441 R448 R411 R603 G JW115 C111 C417 R405 JW66 JW58 R409 JW206 JW87 R401 R604 F JW118 C428 C424 R436 JW92 L700 C400 C416 JW59 R407 JW61 JW60 C447 R404 C619 L900 JW93 C909 R837 L400 R406 C452 R606 C453 E R447 R435 Q601 C425 C426 C446 C620 D600 JW114 JW117 JW120 JW116 C618 R615 JW94 R927 R416 R417 Q400 R440 R414 R415 C107 JW122 R928 JW130 L602 J D919 R424 Ref. No. D400 D600 D801 D808 D811 D812 D813 D814 D815 D816 D817 D902 D903 D904 D905 D906 D907 D908 D909 D912 D914 D915 D916 D917 Location D-4 E-2 I-5 J-9 I-3 I-3 I-3 I-3 I-2 I-2 I-2 B-8 B-8 C-6 C-6 C-7 C-7 C-7 C-7 F-11 C-9 E-10 C-8 C-8 Ref. No. D919 D921 D922 Location D-9 D-7 D-7 IC100 IC401 IC801 IC802 B-6 F-4 H-7 H-10 Q400 Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q601 Q800 Q900 Q902 Q906 Q907 D-4 D-4 C-4 D-3 C-3 C-4 C-4 C-3 E-2 I-6 H-10 E-11 F-11 F-11 CDX-S2000/S2000S/SW200 3-13. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 20 for Circuit Boards Location. LED906 S901 B 3 4 5 6 7 8 9 10 11 12 14 LED908 S902 LSW913 LSW905 LED911 LED910 C 13 LED909 A 2 LED907 1 : Uses unleaded solder. LSW906 LED905 LSW914 LED901 LCD901 S903 LED904 LED902 S905 IC951 S904 D S906 LSW907 LSW909 LSW908 LSW911 LSW910 LSW916 LSW917 LSW918 LSW919 LSW920 (Page 26) I R985 R951 R986 • Semiconductor Location Ref. No. D902 D903 D904 D905 D951 Location F-11 F-9 F-9 F-9 F-9 IC901 G-8 Ref. No. IC905 IC951 Location G-10 D-14 LED901 LED902 LED904 LED905 C-13 C-13 C-3 C-3 Ref. No. LED906 LED907 LED908 LED909 LED910 LED911 Location A-2 A-2 A-14 A-13 C-4 C-12 27 27 R912 R913 R914 R977 R981 R968 R969 R980 R976 R916 R915 R974 R952 R901 D904 D951 R917 R966 R967 R902 R904 R903 C956 IC905 C955 FMB4 R979 R905 R906 R907 CN901 C951 R983 R982 R978 H D902 R918 IC901 G D905 R961 R919 R972 R910 R909 R973 R908 FMB3 R957 C953 D903 R958 C950 R960 R959 F C952 R975 R955 R956 R954 R953 E 15 CDX-S2000/S2000S/SW200 3-14. SCHEMATIC DIAGRAM — DISPLAY SECTION — R952 R972 R966 R974 R976 R986 R980 R982 R951 R978 R967 IC905 IC951 LSW914(2/2) LSW917(1/2) LED902 LSW909(1/2) LSW919(1/2) LSW916(1/2) LED901 LSW906(2/2) LED904 D951 LSW918(1/2) LED910 LED905 C951 CN901 C950 LSW910(1/2) C956 LSW905(2/2) C955 LSW913(2/2) LSW908(1/2) LED911 LED908 LSW920(1/2) R958 LED906 R960 R985 R977 C953 R957 R979 LED909 LSW911(1/2) LED907 R953 R954 R955 C952 R956 R961 D904 D903 LSW907(1/2) R969 R973 R975 R981 R983 D905 LSW919(2/2) LSW920(2/2) LSW911(2/2) R901 R902 R903 R904 R905 R906 R907 R908 R909 LSW906(1/2) LSW907(2/2) LSW908(2/2) LSW909(2/2) S906 LSW918(2/2) R919 LSW905(1/2) R918 LSW917(2/2) R917 S901 R916 LSW916(2/2) R915 S905 R914 S904 LSW914(1/2) R913 S903 LSW913(1/2) R912 LCD901 R910 LSW910(2/2) S902 D902 R968 IC901 R959 (Page 25) 28 28 CDX-S2000/S2000S/SW200 3-15. IC BLOCK DIAGRAMS REV OPIN4(+) OPIN4(–) OPOUT4 OPIN3(+) OPIN3(–) OPOUT3 MUTE BIAS GND VO3(–) VO3(+) VO4(–) VO4(+) IC2 BA5966FP-FE2 (SERVO Board) 28 27 26 25 24 23 22 21 20 19 18 17 16 15 MUTE + – + OUT F FWD OUT R – + + – + LEVEL SHIFT – – + – + 1 2 3 4 5 6 7 8 9 10 11 12 13 14 OPIN1(–) OPOUT1 OPIN2(+) OPIN2(–) OPOUT2 VCC VOL(–) VOL(+) VO2(–) VO2(+) VO1(–) VO1(+) VCC OPIN1(+) + – LEVEL SHIFT + FWD – – LEVEL SHIFT – + – + + + + REV – + – + LOADING DRIVER – + – LEVEL SHIFT – – + + + – – – 29 CDX-S2000/S2000S/SW200 DGND SDA SCL MUTE SEL ADJ VCC OUTF1 OUTR1 OUTF2 OUTR2 DS12 DS22 DS32 OUTS1 OUTS2 IC401 BD3808FS (MAIN Board) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 VCC I2C BUS LOGIC FADER (0~-58, -∞dB) VCO FADER (0~-58, -∞dB) FADER (0~-58, -∞dB) EFFECT (0dB~ +20dB,2dB STEP) BASS fo:60,70,80,100,120,140,160,200Hz Q:0.5,0.75,1,1.25 FADER (0~-58, -∞dB) EFFECT (0dB~ +20dB,2dB STEP) GAIN+ATT (+10~-29, -∞dB) 2ND ORDER LPF fc:OFF,80,120,160Hz Q: 0.707 2ND ORDER LPF MIX TONE PASS TONE PASS MIDDLE fo:500Hz,1kHz Q:1 BASS,TREBLE, MIDDLE (-15dB~+15dB,1dB STEP) BASS,TREBLE, MIDDLE (-15dB~+15dB,1dB STEP) TABLE fo:5,7.5,10,12.5kHz VOLUME (+23~-79dB,-∞dB 1dB STEP) VOLUME (+23~-79dB,-∞dB 1dB STEP) fc:40kHz fc:40kHz ANTI-ALIASING FILTER ANTI-ALIASING FILTER INPUT GAIN (0~15dB,1dB STEP) INPUT GAIN (0~15dB,1dB STEP) MUTE MUTE INPUT SELECTOR (4 STEREO INCLUDE 1 ISOLATION INPUT) 30 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 AGND FIL AP1 AN AP2 B1 B2 C1 C2 D1 D2 DS11 DS21 DS31 NC NC VCC/2 CDX-S2000/S2000S/SW200 SECTION 4 EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet’s Color • Accessories are given in the last of this parts list. • Abbreviation CND : Canadian model The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. 4-1. MAIN SECTION A MG-611XA-186//K #1 #1 not supplied 6 B A F901 5 #2 4 TUX601 3 7 #1 not supplied B 2 #1 #1 1 Ref. No. Part No. Description 1 2 3 4 5 X-3384-407-1 3-231-472-01 X-3382-588-1 3-246-006-31 3-922-535-11 PANEL (1) ASSY, SUB SCREW (+B 2X4) LOCK ASSY (S) COVER SCREW (+BTT) 6 1-776-206-21 CORD (WITH CONNECTOR) (POWER) Remark Ref. No. Part No. Description 7 7 F901 TUX601 #1 A-3283-403-A A-3283-423-A 1-532-877-11 A-3220-959-A 7-685-792-09 MAIN BOARD, COMPLETE (US,CND) MAIN BOARD, COMPLETE (E) FUSE (BLADE TYPE) (AUTO FUSE) 10A TUNER UNIT (TUX-032) SCREW +PTT 2.6X6 (S) #2 7-685-793-09 SCREW +PTT 2.6X8 (S) Remark 31 CDX-S2000/S2000S/SW200 4-2. FRONT PANEL SECTION 57 58 LCD901 #3 59 #3 not supplied 56 55 not supplied (DISPLAY board) not supplied 54 52 54 51 Ref. No. 53 Part No. Description 51 51 51 51 52 A-3372-782-A X-3384-427-1 X-3384-459-1 X-3384-460-1 X-3384-456-1 PANEL SUB ASSY, FRONT (S2000S) PANEL SUB ASSY, FRONT (S2000:US,CND) PANEL SUB ASSY, FRONT (SW200) PANEL SUB ASSY, FRONT (S2000:E) BUTTON ASSY (S) (S2000:US,CND/SW200) 52 52 53 54 55 X-3384-461-1 X-3384-739-1 3-245-998-01 3-246-002-01 3-259-794-01 BUTTON ASSY (S) (S2000:E) BUTTON ASSY (S) (S2000S) FILTER (IR) PLATE (CD), LIGHT GUIDE SPRING (RELEASE) 56 3-246-003-01 PANEL (CD), FRONT BACK 32 Remark Ref. No. 57 58 Part No. Description Remark 58 58 58 X-3378-390-3 CASE ASSY (for FRONT PANEL) A-3372-569-A PANEL OVERALL ASSY, FRONT (S2000:US,CND) A-3372-590-A PANEL OVERALL ASSY, FRONT (S2000:E) A-3372-716-A PANEL OVERALL ASSY, FRONT (SW200) A-3372-781-A PANEL OVERALL ASSY, FRONT (S2000S) 59 LCD901 LCD901 #3 1-694-988-11 1-805-079-11 1-805-449-11 7-685-106-19 CONDUCTIVE BOARD, CONNECTION DISPLAY PANEL, LIQUID CRYSTAL (E) DISPLAY PANEL, LIQUID CRYSTAL (US,CND) SCREW +P 2X10 TYPE2 NON-SLIT CDX-S2000/S2000S/SW200 4-3. CD MECHANISM SECTION (1) (MG-611XA-186//K) not supplied 102 not supplied (SENSOR board) 101 #4 not supplied not supplied 103 104 106 105 108 107 Ref. No. 101 102 103 104 105 Part No. Description A-3372-455-A 3-253-729-01 3-253-746-01 3-253-746-11 3-253-695-01 CHASSIS (T) SUB ASSY SPRING (LTR), TENSION COIL SPRING (DAMPER), COMPRESSION SPRING (DAMPER), COMPRESSION SPRING (KF), TENSION COIL Remark Ref. No. 106 107 108 #4 Part No. Description 3-253-748-01 3-352-758-31 A-3283-350-A 7-627-552-87 DAMPER (S) SCREW (M1.7), TOOTHED LOCK SERVO BOARD, COMPLETE SCREW, PRECISION +P 1.7X2.2 Remark 33 CDX-S2000/S2000S/SW200 4-4. CD MECHANISM SECTION (2) (MG-611XA-186//K) 155 156 157 154 (including M901) #5 M902 not supplied SW4 not supplied 158 not supplied 153 not supplied 151 152 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description 151 152 0 153 154 155 A-3337-637-A 4-912-432-01 8-820-207-02 A-3337-640-A A-3337-641-A CHASSIS (OP) COMPLETE ASSY SCREW (B1.4X5), TAPPING OPTICAL PICK-UP (KSS1000E/K1RP) CHASSIS (OP) SUB ASSY (including M901) ARM SUB ASSY, CHUCKING 156 34 A-3337-639-A LEVER (SL) SUB ASSY Remark Ref. No. 157 158 M902 SW4 #5 Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. Part No. Description X-3383-454-2 3-261-959-01 A-3337-638-A 1-571-099-11 7-627-850-77 LEVER (SL) ASSY SPRING (SL), TORSION MOTOR ASSY, SL (SLED) SWITCH (1 KEY) (LIMIT) SCREW, PRECISION +P 1.4X1.8 Remark CDX-S2000/S2000S/SW200 4-5. CD MECHANISM SECTION (3) (MG-611XA-186//K) 203 201 202 207 211 204 209 208 210 205 207 207 M903 #4 206 Ref. No. Part No. Description 201 202 203 204 205 3-338-647-31 3-259-024-01 A-3337-633-A 3-259-455-01 3-253-713-01 WASHER (1.0-2.5) WHEEL (RA), WORM ARM ASSY, ROLLER SPRING (RAL) SPRING (RAR) 206 207 3-259-469-01 SPRING (LE), LEAF 2-134-636-31 SCREW (M1.7X2.5) Remark Ref. No. Part No. Description 208 209 210 211 M903 3-259-467-01 3-345-648-91 A-3372-456-A 3-259-468-01 A-3372-454-A BRACKET (LEM) SCREW (M1.4), TOOTHED LOCK WORM (LEB) ASSY BEARING (LEB) MOTOR ASSY, LE (LOADING) #4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2 Remark 35 CDX-S2000/S2000S/SW200 4-6. CD MECHANISM SECTION (4) (MG-611XA-186//K) 254 252 255 252 256 251 253 257 Ref. No. 251 252 253 254 36 Part No. Description 3-259-429-01 3-344-223-01 3-259-470-01 3-253-755-01 WHEEL (LE), WORM WASHER GEAR (LE1) LEVER (D) Remark Ref. No. 255 256 257 Part No. Description 3-899-829-01 WASHER (SLIT) 3-259-032-01 GEAR (LE2) A-3372-453-A CHASSIS (M) BLOCK ASSY Remark CDX-S2000/S2000S/SW200 SECTION 5 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. • CAPACITORS uF : µF • COILS uH : µH • Abbreviation CND : Canadian model When indicating parts by reference number, please include the board. Ref. No. Part No. Description Remark 1-694-988-11 CONDUCTIVE BOARD, CONNECTION < CAPACITOR > 1-107-826-11 1-164-227-11 1-125-891-11 1-162-927-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP C956 1-125-837-11 CERAMIC CHIP Part No. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. Description Remark LED907 6-500-511-01 LED CL-270PG-C-TS (DISC IND L) (SW200) LED907 8-719-082-38 LED CL-270SR-C-TS (DISC IND L) (S2000/S2000S) LED908 6-500-510-01 LED CL-195PG-CD-T (Z) (SW200) LED908 8-719-053-09 LED SML-310VT-T86 (Z) (S2000/S2000S) LED909 6-500-511-01 LED CL-270PG-C-TS (DISC IND R) (SW200) DISPLAY BOARD ************** C950 C951 C952 C953 C955 Ref. No. DISPLAY 0.1uF 0.022uF 0.47uF 100PF 0.1uF 10% 10% 10% 5% 10% 16V 25V 10V 50V 16V 1uF 10% 6.3V LED909 8-719-082-38 LED CL-270SR-C-TS (DISC IND R) (S2000/S2000S) LED910 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT) LED911 6-500-459-01 LED NSCW505T-ARS (LCD BACK LIGHT) < SWITCH > < CONNECTOR > CN901 1-794-312-21 PIN, CONNECTOR 12P < DIODE > D902 D903 D904 D905 D951 8-719-069-54 8-719-069-54 8-719-069-54 8-719-988-61 8-719-069-54 DIODE DIODE DIODE DIODE DIODE UDZS-TE17-5.1B UDZS-TE17-5.1B UDZS-TE17-5.1B 1SS355TE-17 UDZS-TE17-5.1B < IC > IC901 IC905 IC951 6-705-180-01 IC LC75827W 6-705-374-01 IC MM3033DULE 6-600-321-01 IC KSM-401Y (IR) LSW905 1-762-619-21 SWITCH, KEYBOARD (WITH LED) (VOLUME +) (SW200) LSW905 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (VOLUME +) (S2000/S2000S) LSW906 1-762-619-21 SWITCH, KEYBOARD (WITH LED) (VOLUME –) (SW200) LSW906 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (VOLUME –) (S2000/S2000S) LSW907 1-771-609-31 SWITCH, TACTILE (WITH LED) (ATT) (SW200) LSW907 1-771-883-31 SWITCH, TACTILE (WITH LED) (ATT) (S2000/S2000S) LSW908 1-771-609-31 SWITCH, TACTILE (WITH LED) (SENS) (SW200) LSW908 1-771-883-31 SWITCH, TACTILE (WITH LED) (SENS) (S2000/S2000S) LSW909 1-771-609-31 SWITCH, TACTILE (WITH LED) (1) (SW200) LSW909 1-771-883-31 SWITCH, TACTILE (WITH LED) (1) (S2000/S2000S) < LIQUID CRYSTAL DISPLAY > LCD901 1-805-079-11 DISPLAY PANEL, LIQUID CRYSTAL (E) LCD901 1-805-449-11 DISPLAY PANEL, LIQUID CRYSTAL (US,CND) < DIODE > LED901 LED901 LED902 LED902 LED904 6-500-510-01 8-719-053-09 6-500-510-01 8-719-053-09 6-500-510-01 LED LED LED LED LED CL-195PG-CD-T (OFF) (SW200) SML-310VT-T86 (OFF) (S2000/S2000S) CL-195PG-CD-T (EQ3) (SW200) SML-310VT-T86 (EQ3) (S2000/S2000S) CL-195PG-CD-T (SOURCE) (SW200) LED904 8-719-053-09 LED SML-310VT-T86 (SOURCE) (S2000/S2000S) LED905 6-500-510-01 LED CL-195PG-CD-T (MODE) (SW200) LED905 8-719-053-09 LED SML-310VT-T86 (MODE) (S2000/S2000S) LED906 6-500-510-01 LED CL-195PG-CD-T (SEL) (SW200) LED906 8-719-053-09 LED SML-310VT-T86 (SEL) (S2000/S2000S) LSW910 1-771-609-31 SWITCH, TACTILE (WITH LED) (2) (SW200) LSW910 1-771-883-31 SWITCH, TACTILE (WITH LED) (2) (S2000/S2000S) LSW911 1-771-609-31 SWITCH, TACTILE (WITH LED) (3) (SW200) LSW911 1-771-883-31 SWITCH, TACTILE (WITH LED) (3) (S2000/S2000S) LSW913 1-762-619-21 SWITCH, KEYBOARD (WITH LED) (SEEK + > M) (SW200) LSW913 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (SEEK + > M) (S2000/S2000S) LSW914 1-762-619-21 SWITCH, KEYBOARD (WITH LED) (SEEK m . –) (SW200) LSW914 1-771-476-11 SWITCH, KEYBOARD (WITH LED) (SEEK m . –) (S2000/S2000S) LSW916 1-771-609-31 SWITCH, TACTILE (WITH LED) (DSPL) (SW200) LSW916 1-771-883-31 SWITCH, TACTILE (WITH LED) (DSPL) (S2000/S2000S) 37 CDX-S2000/S2000S/SW200 DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LSW917 1-771-609-31 SWITCH, TACTILE (WITH LED) (BTM) (SW200) LSW917 1-771-883-31 SWITCH, TACTILE (WITH LED) (BTM) (S2000/S2000S) LSW918 1-771-609-31 SWITCH, TACTILE (WITH LED) (6) (SW200) LSW918 1-771-883-31 SWITCH, TACTILE (WITH LED) (6) (S2000/S2000S) LSW919 1-771-609-31 SWITCH, TACTILE (WITH LED) (5) (SW200) R975 1-216-808-11 METAL CHIP 82 R975 1-216-809-11 METAL CHIP 100 R976 1-216-811-11 METAL CHIP 150 R976 1-216-813-11 METAL CHIP 220 LSW919 1-771-883-31 SWITCH, TACTILE (WITH LED) (5) (S2000/S2000S) LSW920 1-771-609-31 SWITCH, TACTILE (WITH LED) (4) (SW200) LSW920 1-771-883-31 SWITCH, TACTILE (WITH LED) (4) (S2000/S2000S) R977 1-216-811-11 METAL CHIP 150 R977 1-216-813-11 METAL CHIP 220 R978 1-216-811-11 METAL CHIP 150 R978 1-216-813-11 METAL CHIP 220 R979 1-216-811-11 METAL CHIP 150 R979 1-216-813-11 METAL CHIP 220 < RESISTOR > R901 R902 R903 R904 R905 1-216-819-11 1-216-819-11 1-216-819-11 1-216-821-11 1-218-851-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP 680 680 680 1K 1.5K 5% 5% 5% 5% 2% 1/10W 1/10W 1/10W 1/10W 1/16W R906 R907 R908 R909 R910 1-218-851-11 1-216-825-11 1-216-827-11 1-216-829-11 1-218-867-11 RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.5K 2.2K 3.3K 4.7K 6.8K 2% 5% 5% 5% 5% 1/16W 1/10W 1/10W 1/10W 1/10W R980 1-216-808-11 METAL CHIP 82 R980 1-216-809-11 METAL CHIP 100 R981 1-216-808-11 METAL CHIP 82 R912 R913 R914 R915 R916 1-216-819-11 1-216-819-11 1-216-819-11 1-216-821-11 1-218-851-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP 680 680 680 1K 1.5K 5% 5% 5% 5% 2% 1/10W 1/10W 1/10W 1/10W 1/16W R981 1-216-809-11 METAL CHIP 100 R982 1-216-808-11 METAL CHIP 82 R982 1-216-809-11 METAL CHIP 100 R917 R918 R919 R951 R952 1-218-851-11 1-216-825-11 1-216-827-11 1-216-815-11 1-216-825-11 RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.5K 2.2K 3.3K 330 2.2K 2% 5% 5% 5% 5% 1/16W 1/10W 1/10W 1/10W 1/10W R983 1-216-808-11 METAL CHIP 82 R983 1-216-809-11 METAL CHIP 100 R985 1-216-811-11 METAL CHIP 150 R953 R954 R955 R956 R957 1-216-821-11 1-216-821-11 1-216-821-11 1-216-821-11 1-216-850-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1K 1K 270K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R985 1-216-813-11 METAL CHIP 220 R986 1-216-811-11 METAL CHIP 150 R958 R959 R960 R961 R966 1-216-821-11 1-216-821-11 1-216-821-11 1-216-857-11 1-216-815-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 1K 1K 1M 330 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R986 1-216-813-11 METAL CHIP 220 R967 R968 R969 R972 1-216-815-11 1-216-815-11 1-216-815-11 1-216-808-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 330 330 330 82 5% 5% 5% 5% R972 1-216-809-11 METAL CHIP 100 R973 1-216-808-11 METAL CHIP 82 R973 1-216-809-11 METAL CHIP 100 R974 1-216-808-11 METAL CHIP 82 R974 1-216-809-11 METAL CHIP 100 38 1/10W 1/10W 1/10W 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) 5% 1/10W (SW200) 5% 1/10W (S2000/S2000S) < SWITCH > S901 S902 S903 S904 S905 1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31 1-771-884-31 SWITCH, TACTILE (SEL) SWITCH, TACTILE (Z) SWITCH, TACTILE (OFF) SWITCH, TACTILE (SOURCE) SWITCH, TACTILE (MODE) S906 1-771-884-31 SWITCH, TACTILE (EQ3) ************************************************************* CDX-S2000/S2000S/SW200 MAIN Ref. No. Part No. Part No. Description A-3283-403-A MAIN BOARD, COMPLETE (including SPEAKER BOARD) (US,CND) A-3283-423-A MAIN BOARD, COMPLETE (including SPEAKER BOARD) (E) ********************* Description Remark C812 C813 C815 C816 C817 1-107-826-11 1-124-584-00 1-162-964-11 1-164-160-11 1-162-918-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 100uF 0.001uF 20PF 18PF 10% 20% 10% 5% 5% 16V 10V 50V 50V 50V 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-793-09 SCREW +PTT 2.6X8 (S) 7-685-795-09 SCREW +PTT 2.6X12 (S) C818 C820 C821 C822 C823 1-164-160-11 1-162-920-11 1-107-826-11 1-107-826-11 1-162-927-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 20PF 27PF 0.1uF 0.1uF 100PF 5% 5% 10% 10% 5% 50V 50V 16V 16V 50V C824 C825 C908 C909 C922 1-162-927-11 1-124-584-00 1-126-160-11 1-162-970-11 1-131-868-81 CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT 100PF 100uF 1uF 0.01uF 3300uF 5% 20% 20% 10% 20% 50V 10V 50V 25V 16V < CAPACITOR > C101 C106 C107 C108 C109 1-124-233-11 1-124-234-00 1-124-233-11 1-216-864-11 1-124-233-11 ELECT ELECT ELECT METAL CHIP ELECT 10uF 22uF 10uF 0 10uF 20% 20% 20% 5% 20% 16V 16V 16V 1/10W 16V C111 C113 C303 C400 C408 1-124-233-11 1-107-823-11 1-216-864-11 1-162-970-11 1-115-467-11 ELECT CERAMIC CHIP METAL CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.47uF 0 0.01uF 0.22uF 20% 10% 5% 10% 10% 16V 16V 1/10W 25V 10V C409 C410 C411 C414 C416 1-115-467-11 1-104-942-11 1-104-942-11 1-128-428-11 1-162-970-11 CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP 0.22uF 1uF 1uF 10uF 0.01uF 10% 20% 20% 20% 10% 10V 50V 50V 35V 25V C417 C424 C425 C426 C428 1-124-589-11 1-128-428-11 1-128-428-11 1-128-428-11 1-128-428-11 ELECT ELECT ELECT ELECT ELECT 47uF 10uF 10uF 10uF 10uF 20% 20% 20% 20% 20% 16V 35V 35V 35V 35V C430 C435 C436 C437 C438 1-126-947-11 1-162-927-11 1-162-927-11 1-125-891-11 1-125-891-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 100PF 100PF 0.47uF 0.47uF 20% 5% 5% 10% 10% 16V 50V 50V 10V 10V C440 C441 C444 C446 C447 1-125-891-11 1-115-467-11 1-125-891-11 1-162-923-11 1-124-257-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT 0.47uF 0.22uF 0.47uF 47PF 2.2uF 10% 10% 10% 5% 20% 10V 10V 10V 50V 50V C452 C453 C600 C618 C619 1-128-428-11 1-128-428-11 1-216-864-11 1-126-786-11 1-124-247-61 ELECT ELECT METAL CHIP ELECT ELECT 10uF 10uF 0 47uF 10uF 20% 20% 5% 20% 20% 35V 35V 1/10W 16V 35V C620 C621 C701 C704 C705 1-107-826-11 1-115-156-11 1-124-584-00 1-124-584-00 1-124-584-00 CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT 0.1uF 1uF 100uF 100uF 100uF 10% 20% 20% 20% 16V 10V 10V 10V 10V C706 C707 C709 C801 C802 1-162-964-11 1-124-584-00 1-162-964-11 1-107-826-11 1-124-589-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT 0.001uF 100uF 0.001uF 0.1uF 47uF 10% 20% 10% 10% 20% 50V 10V 50V 16V 16V C807 C809 C810 1-162-970-11 CERAMIC CHIP 0.01uF 1-124-584-00 ELECT 100uF 1-125-701-11 DOUBLE LAYERS 0.047F 10% 20% 25V 10V 5.5V Ref. No. Remark < CONNECTOR > CN751 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P CNP800 1-794-311-21 PLUG, CONNECTOR 12P CNP901 1-774-701-21 PIN, CONNECTOR 16P < DIODE > D400 D600 D702 D801 D808 8-719-988-61 8-719-069-55 1-216-864-11 8-719-988-61 8-719-978-33 DIODE 1SS355TE-17 DIODE UDZS-TE17-5.6B METAL CHIP 0 DIODE 1SS355TE-17 DIODE DTZ-TT11-6.8B D811 D812 D813 D814 D815 8-719-109-97 8-719-109-97 8-719-109-97 8-719-109-97 8-719-109-97 DIODE DIODE DIODE DIODE DIODE RD6.8ES-B2 RD6.8ES-B2 RD6.8ES-B2 RD6.8ES-B2 RD6.8ES-B2 D816 D817 D902 D903 D904 8-719-109-97 8-719-109-97 8-719-053-18 8-719-053-18 8-719-970-02 DIODE DIODE DIODE DIODE DIODE RD6.8ES-B2 RD6.8ES-B2 1SR154-400TE-25 1SR154-400TE-25 1SR139-400 D905 D906 D907 D908 D909 8-719-970-02 8-719-970-02 8-719-970-02 8-719-970-02 8-719-970-02 DIODE DIODE DIODE DIODE DIODE 1SR139-400 1SR139-400 1SR139-400 1SR139-400 1SR139-400 D912 D914 D915 D916 D917 8-719-083-66 8-719-978-33 8-719-056-84 8-719-970-02 8-719-970-02 DIODE DIODE DIODE DIODE DIODE UDZS-TE17-18B DTZ-TT11-6.8B UDZ-TE-17-7.5B 1SR139-400 1SR139-400 D919 D921 D922 8-719-049-38 DIODE 1N5404TU 8-719-970-02 DIODE 1SR139-400 8-719-970-02 DIODE 1SR139-400 5% 1/10W < IC > IC100 IC401 IC801 IC802 6-705-360-01 6-705-372-01 6-803-819-01 8-759-659-13 IC IC IC IC TDA8588BJ/N2 BD3808FS-FE2 MB90473PF-G165-BNDE1 PST3428UL 39 CDX-S2000/S2000S/SW200 MAIN Ref. No. Part No. Description Remark < JUMPER RESISTOR > JR5 JR6 JR10 JR11 JR103 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 0 0 0 0 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W < COIL > L400 L602 L700 L701 L702 1-414-398-11 1-414-394-41 1-410-501-11 1-410-501-11 1-410-509-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR L900 1-456-617-11 COIL, CHOKE 10uH 2.2uH 2.2uH 2.2uH 10uH 250uH < JACK > PJ401 PJ601 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR) 1-793-598-11 JACK (ANTENNA) Ref. No. Part No. Description R436 R437 R440 R441 R442 1-216-809-11 1-216-821-11 1-216-809-11 1-216-809-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 1K 100 100 47K 5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W R443 R447 R448 R603 R604 1-216-841-11 1-216-809-11 1-216-841-11 1-247-807-31 1-247-807-31 METAL CHIP METAL CHIP METAL CHIP CARBON CARBON 47K 100 47K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/4W 1/4W R606 R607 R608 R615 R703 1-216-809-11 1-216-809-11 1-216-809-11 1-216-821-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 1K 0 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R705 R707 R709 R722 R800 1-216-809-11 1-216-809-11 1-216-864-11 1-216-809-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 0 100 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W (E) METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 0 100 10K 10K 5% 5% 5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W < TRANSISTOR > Q400 Q401 Q402 Q403 Q404 8-729-027-46 8-729-027-31 6-550-752-01 6-550-752-01 6-550-752-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114YKA-T146 DTA124EKA-T146 DTC614TKT146 DTC614TKT146 DTC614TKT146 R801 R802 R804 R805 R806 1-216-809-11 1-216-864-11 1-216-809-11 1-218-871-11 1-218-871-11 Q405 Q406 Q407 Q601 Q800 6-550-752-01 6-550-752-01 6-550-752-01 8-729-106-68 8-729-027-31 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC614TKT146 DTC614TKT146 DTC614TKT146 2SD1615A-GP DTA124EKA-T146 R808 1-216-845-11 METAL CHIP 100K 5% R808 1-216-864-11 METAL CHIP 0 5% R809 1-216-845-11 METAL CHIP 100K 5% Q900 Q902 Q906 Q907 8-729-901-81 8-729-900-53 8-729-901-81 8-729-900-53 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC2412K-T-146-R DTC114EK 2SC2412K-T-146-R DTC114EK R810 R811 1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP 100K 100K 5% 5% 1/10W (E) 1/10W (US,CND) 1/10W (E) 1/10W 1/10W R814 R815 R818 R819 R821 1-216-845-11 1-249-435-11 1-216-809-11 1-216-809-11 1-216-817-11 METAL CHIP CARBON METAL CHIP METAL CHIP METAL CHIP 100K 33K 100 100 470 5% 5% 5% 5% 5% 1/10W 1/4W 1/10W 1/10W 1/10W R822 R823 R824 R825 R826 1-216-817-11 1-216-817-11 1-216-849-11 1-216-849-11 1-216-843-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470 220K 220K 68K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R828 R830 R832 R833 R834 1-216-809-11 1-216-809-11 1-218-867-11 1-249-417-11 1-218-867-11 METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP 100 100 6.8K 1K 6.8K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/4W 1/10W R835 R837 R838 R839 R840 1-216-845-11 1-216-864-11 1-216-845-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 0 100K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R841 R843 R844 R846 R847 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W < RESISTOR > R404 R405 R406 R407 R409 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-839-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R411 R412 R414 R415 R416 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R417 R418 R419 R420 R421 1-216-809-11 1-216-841-11 1-216-841-11 1-216-841-11 1-216-841-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 47K 47K 47K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R424 R427 R429 R431 R432 1-216-805-11 1-216-809-11 1-247-807-31 1-247-807-31 1-216-809-11 METAL CHIP METAL CHIP CARBON CARBON METAL CHIP 47 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/4W 1/4W 1/10W R435 1-216-809-11 METAL CHIP 100 5% 1/10W 40 CDX-S2000/S2000S/SW200 MAIN Ref. No. SENSOR SERVO Part No. Description Remark Ref. No. Part No. Description R848 R849 R850 R851 R852 1-216-845-11 1-216-841-11 1-218-871-11 1-216-809-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 47K 10K 100 0 5% 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C19 C20 C21 C23 C25 1-107-826-11 1-107-826-11 1-162-970-11 1-162-923-11 1-162-908-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.01uF 47PF 3PF 10% 10% 10% 5% 0.25PF 16V 16V 25V 50V 50V R853 R854 R860 R873 R901 1-216-864-11 1-216-864-11 1-216-845-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 0 0 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C26 C27 C28 C29 C30 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-162-921-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 33PF 10% 10% 10% 10% 5% 16V 16V 16V 16V 50V R902 R903 R904 R912 R913 1-216-829-11 1-216-841-11 1-216-841-11 1-249-417-11 1-216-821-11 METAL CHIP METAL CHIP METAL CHIP CARBON METAL CHIP 4.7K 47K 47K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/4W 1/10W C31 C32 C34 C35 C36 1-162-925-11 1-107-826-11 1-107-826-11 1-162-970-11 1-162-967-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 68PF 0.1uF 0.1uF 0.01uF 0.0033uF 5% 10% 10% 10% 10% 50V 16V 16V 25V 50V R917 R925 R927 R928 R931 1-249-421-11 1-216-845-11 1-216-833-11 1-249-421-11 1-216-073-00 CARBON METAL CHIP METAL CHIP CARBON RES-CHIP 2.2K 100K 10K 2.2K 10K 5% 5% 5% 5% 5% 1/4W 1/10W 1/10W 1/4W 1/10W C37 C38 C39 C70 C71 1-162-970-11 1-104-609-11 1-107-826-11 1-162-965-11 1-162-965-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 100uF 0.1uF 0.0015uF 0.0015uF 10% 20% 10% 10% 10% 25V 4V 16V 50V 50V R932 R936 1-216-073-00 RES-CHIP 1-216-864-11 METAL CHIP 10K 0 5% 5% 1/10W 1/10W C72 C73 C74 C75 C76 1-162-962-11 1-162-962-11 1-107-826-11 1-107-826-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 470PF 470PF 0.1uF 0.1uF 0.01uF 10% 10% 10% 10% 10% 50V 50V 16V 16V 25V C77 C78 C79 1-162-970-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP 0.01uF 0.022uF 0.022uF 10% 10% 10% 25V 25V 25V < SWITCH > S800 S802 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) (E) 1-692-431-21 SWITCH, TACTILE (RESET) < TUNER > TUX601 A-3220-959-A TUNER UNIT (TUX-032) Remark < CONNECTOR > < VIBRATOR > CN1 CN2 1-817-275-21 CONNECTOR, BOARD TO BOARD 28P 1-794-153-21 CONNECTOR, FPC (ZIF) 16P X800 1-767-993-21 VIBRATOR, CRYSTAL (3.68MHz) X801 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz) ************************************************************* < FERRITE BEAD > FB1 1-414-760-21 FERRITE, EMI (SMD) SENSOR BOARD ************** < IC > < SWITCH > IC1 IC2 6-703-699-01 IC uPD63712GC-8EU-A 6-705-002-01 IC BA5966FP-FE2 SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF) SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN) ************************************************************* < FERRITE BEAD > JR40 JR41 JR90 JR91 A-3283-350-A SERVO BOARD, COMPLETE ********************** 1-414-760-21 1-414-760-21 1-414-760-21 1-414-760-21 FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) FERRITE, EMI (SMD) < CAPACITOR > < TRANSISTOR > C1 C2 C3 C5 C6 1-107-826-11 1-162-970-11 1-107-826-11 1-107-826-11 1-100-381-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.1uF 0.01uF 0.1uF 0.1uF 10uF 10% 10% 10% 10% 20% 16V 25V 16V 16V 16V C7 C8 C11 C13 C17 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C18 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V Q1 8-729-904-87 TRANSISTOR 2SB1197K-R < RESISTOR > R1 R6 R7 R9 R11 1-216-841-11 1-216-833-11 1-216-840-11 1-216-822-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 10K 39K 1.2K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R12 R13 1-216-809-11 METAL CHIP 1-216-833-11 METAL CHIP 100 10K 5% 5% 1/10W 1/10W 41 CDX-S2000/S2000S/SW200 SERVO Ref. No. Part No. Description R14 R15 R41 R42 R44 1-216-797-11 1-216-797-11 1-216-821-11 1-216-821-11 1-414-760-21 METAL CHIP 10 METAL CHIP 10 METAL CHIP 1K METAL CHIP 1K FERRITE, EMI (SMD) Remark R45 R70 R71 R72 R73 1-414-760-21 1-216-842-11 1-216-833-11 1-216-842-11 1-216-833-11 R74 R75 R76 R77 R78 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W FERRITE, EMI (SMD) METAL CHIP 56K METAL CHIP 10K METAL CHIP 56K METAL CHIP 10K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1-216-837-11 1-216-833-11 1-216-837-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 22K 10K 22K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R79 R80 R81 R82 R83 1-216-833-11 1-216-833-11 1-216-833-11 1-216-837-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 22K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R84 R85 1-216-837-11 METAL CHIP 1-216-833-11 METAL CHIP 22K 10K 5% 5% 1/10W 1/10W Ref. No. Part No. Description Remark PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 301 302 303 304 305 X-3382-647-1 X-3366-972-2 3-246-471-01 3-246-009-01 3-246-011-01 306 1-776-206-21 CORD (WITH CONNECTOR) (POWER) 301 303 FRAME ASSY, FITTING SCREW ASSY (EXP), FITTING (E) SCREW (+K 5X8 TP) COLLAR KEY (FRAME) 302 304 305 306 < SWITCH > SW1 1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN) < VIBRATOR > X1 1-795-562-21 VIBRATOR, CERAMIC (16.9344MHz) ************************************************************* MISCELLANEOUS *************** 6 0 153 154 F901 M902 1-776-206-21 8-820-207-02 A-3337-640-A 1-532-877-11 A-3337-638-A CORD (WITH CONNECTOR) (POWER) OPTICAL PICK-UP (KSS1000E/K1RP) CHASSIS (OP) SUB ASSY (including M901) FUSE (BLADE TYPE) (AUTO FUSE) 10A MOTOR ASSY, SL (SLED) M903 A-3372-454-A MOTOR ASSY, LE (LOADING) SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT) ************************************************************* ACCESSORIES ************ 3-261-840-31 MANUAL, INSTRUCTION (ENGLISH,FRENCH) (S2000:US,CND) 3-261-840-41 MANUAL, INSTRUCTION (ENGLISH,SPANISH, TRADITIONAL CHINESE) (E) 3-261-840-61 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (SW200) 3-261-841-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH, FRENCH) (S2000:US,CND) 3-261-841-41 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH,TRADITIONAL CHINESE) (E) 3-261-841-61 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH) (SW200) X-3378-390-3 CASE ASSY (for FRONT PANEL) ************************************************************* 42 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. CDX-S2000/S2000S/SW200 MEMO 43 CDX-S2000/S2000S/SW200 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. 1.0 1.1 44 Date 2003. 11 2006. 05 Description of Revision New Correction of RF level. (SPM-06010)

Cdx-s2000/s2000s/sw200

Rating

Date

Size

Views

Categories

Share

Transcript

Forgot your password?.