Transcript
Outdoor Camera Housing CE-H13 Installation Guide
CLINTON Electronics 6701 Clinton Road Loves Park, IL 61111
1.800.447.3306 Sales 1.800.549.6393 Support 1.800.633.8712 Fax
www.clintonelectronics.com
Included Items:
3. Attach Camera to Adjustable Plate
Housing Case (qty. 1) Mounting Arm (qty. 1) 5mm Allen Wrench (qty. 1) Mounting Screws (1/4”-20 x 1.25”) (qty. 4) Wall Anchors (qty. 4) Camera Mounting Screw (1/4”-20 x 6mm) (qty. 1) Camera Mounting Screw (1/4”-20 x 12mm) (qty. 1) Washers (qty. 6) Adaptor Plate (qty. 1)
With a #2 Phillips screwdriver, remove the mounting plate that is attached to the housing by loosening the 4 screws and sliding the plate out.
Required Tools: #2 Phillips Screwdriver Drill with 10mm bit, or #2 Phillips bit 7mm drill bit
Assembly Instructions 1. Attach Mount Arm
OSD IRIS
EXTR
A
VIDEO
OUT
JACK
Feed the 24V/1A AC power, and a/v cables through the mounting arm using one of the cord routing options shown below. Then use the supplied screws, washers, and anchors as needed to secure the arm to the building structure. (Use 7mm drill bitJumper for anchors, 24V AC to Camera #2 Phillips bit or 10mm bit for screws) R
POWE
SET
DC
VIDEO
If needed, use the plastic adaptor plate to raise the camera up from the bottom plate. Using this plate will also allow for smoother adjustBNC Input ment of the camera later. If using the plate, mount camera using a 24V AC Input to washer andBoard the 1/4”-20 x 12mm screw. If not using the plastic adaptor Fan/Heater plate, mount camera using a washer and the 1/4”-20 x 6mm24V screw. AC Jumper
OSD IRIS
EXTR
A
VIDEO
OUT
JACK R
POWE
SET
DC VIDEO
to Camera
Cord route option 1: back of arm
Cord route option 2: bottom of arm
Plastic Adaptor Plate Optional
Cord route option 1: back of arm Cord route option 1: back of arm Cord route option 2: bottom of arm Cord route option 2: bottom of arm
2. Open Housing
Secure housing lid & internal Replace the mounting plate with attached camera camera into when theadjusting housing by sliding it onto the screws. You may wish to leave it loose for later Gently pull upward from base of housing & rotate adjustment of focus depth. If no adjustment is necessary, tighten the screws to secure it in place. Loosen screw ju
Using the supplied allen wrench, loosen the two screws on the side of the housing to open the case. Secure housing lid & internal camera when adjusting
enough to adjus
Gently pull upward from base of housing & rotate
Loosen screw just enough to adjust
OSD IRIS
EXTR
A
VIDEO
OUT
BNC Input
JACK R
CLINTON Electronics 6701 Clinton Road Loves Park, IL 61111 24V AC Jumper to Camera
POWE
24V AC Input to 1.800.447.3306 Sales Fan/Heater Board 1.800.549.6393 Support 1.800.633.8712 Fax SET
DC
VIDEO
www.clintonelectronics.com
S c Sec cam
7. Adjust Angle
Assembly Instructions
Plastic Adapto Plate Optional
You can adjust the angle of the arm by loosening the single allen screw located on the underside of the mount’s arm. Gently pull upward on the base of the housing, and rotate. *NOTE: Loosen screw just enough to move the housing into position. Loosening all the way will separate the arm from the housing. Adjust the arm slowly to protect the housing lid from opening, or the internal camera from harsh movements.
4. Prepare to route wires Unscrew the cable nut to reveal a plastic nipple inserted in the nut. Remove this piece and lightly screw on the cable nut to prepare to feed the cables through the hole.
OSD IRIS
EXTR
A
BNC Input
T
O OU
VIDE
K JAC ER
POW
Secure housing lid & internal camera when adjusting
OSD IRIS
5. Feed wires through hole
EXTR
A
24V AC Input to Fan/Heater Board
O VIDE
Gently pull upward from base of housing & rotate
BNC Input
T
O OU
VIDE
SET
DC
JACK ER
POW
SET
24V AC Input to Fan/Heater Board
DC DEO
VI
Feed the wires through the cable nuts on the bottom of the camera, and pull as much slack as needed into the interior of the camera housing. Tighten the cable nuts, then place the housing 24V AC Jumper to Camera on the arm to prepare for the next step.
OSD IRIS
EXTR
A
VIDEO
OUT
K
JAC
R
POWE
SET
DC
24V AC Jumper to Camera
Loosen screw just enough to adjust
8. Complete setup BNC Input
24V AC Input to Fan/Heater Board
Make any final electrical connections to the heater/fan board and camera. Typical 24V/1A AC connection will run to the heater board first, then a jumper from the board to the camera.
VIDEO
24V AC Jumper to Camera
Cord route option 1: back of arm
Cord route option 2: bottom of arm OSD
Plastic Adaptor Plate Optional
Plastic Adaptor Plate Optional
IRIS
EX
TRA
T EO OU
VID
Plastic Ad Plate Opti
BNC Input
JACK R
POWE
SET
DC VIDEO
24V AC Input to Fan/Heater Board
24V AC Jumper to Camera
6. Attach Housing to Arm Attach the housing to the arm of the mount by tightening the four allen screws located on the underside of the arm. Secure housing lid & internal camera when adjusting Gently pull upward from base of housing & rotate
Test and verify focus, zoom, and other parameters before closing the case. Once complete, close the housing by tightening the two allen screws that were loosened in Step 2.
Loosen screw just enough to adjust
Plastic Adaptor Plate Optional
Secure housing lid & internal camera when adjusting
Secure housing lid & internal camera when adjusting
Gently pull upward from base of housing & rotate
Gently pull upward from base of housing & rotate
Loosen screw just enough to adjust
CLINTON Electronics 6701 Clinton Road Loves Park, IL 61111
Loosen screw just enough to adjust
1.800.447.3306 Sales 1.800.549.6393 Support 1.800.633.8712 Fax
www.clintonelectronics.com
Secure h camera w
v.02.09.12
