Transcript
Central Door Locking p/n 900.705 Fitting Instructions Actuators and Linkages •Select a mounting location inside the door that will allow the window to roll up and down without interruption and a position that will not interfere with any other moving parts inside the door. •The actuator should be mounted on a flat surface, or the included bracket may be used. •Once a stable location is selected, mount the actuator using the two possible methods, as shown in the diagrams. (Direct to door frame mounting method as Fig.2 or mounting bracket method, Fig 3). •Place a connecting rod through the hole in the top of actuator, as Fig 4. •Connect the actuator connecting rod to the vehicle’s door lock linkage rod using the rod clamp and screws provided. In some cases, it will be necessary to bend the actuator rod •If bending the actuator connecting rod, to reach the vehicle’s door lock linkage rod, refer to Fig 5 - 6. •Make sure the actuator pushes and pulls the vehicle door lock rod as straight as possible and without limiting the actuator full travel to prevent damage to the actuator and to assure smooth operation.
Important: The actuator rod must run parallel to the vehicle’s lock rod as much as possible. •Secure by inserting the 4x7mm cross head screws into the threaded holes of the clamp and tighten firmly. •The clamps to the vehicle’s door lock linkage rod must be fasten as tight as possible to prevent slipping when the actuators are activated. •Manually move the existing door lock button from the locked to the unlocked position and check the entire door lock mechanism must be free from any kinks or bends which would prevent free movement. • Tighten any loose screws, nuts and bolts. •Repeat procedures for the remaining door. •It’s recommended to thoroughly clean the entire locking mechanism (not including the actuators) and spray it with silicon to ensure free movement. Flavio Alessio 15 November 2005
Central Door Locking p/n 900.705 Fitting Instructions ELECTRICAL INSTALLATION •Plug the five wires Blue, Green, White, Brown, Black from loom, into the matching colour wires on the 5-wires, front door, actuators. •Connect the wires Blue, Green from loom to the back door actuators. •Secure the Black wire to chassis ground. •Splice the Red fused wire to a constant 12V positive source at the fuse box that is rated at least 20 Amps. •Connect Grey wire to brake switch, negative side (stop light side). •The central locking unit will lock the doors when switching ignition “On”. Note: To eliminate this function disconnect the Grey wire to the brake pedal. Connect Yellow wire to Accessories power + 12V
FUNCTION TEST •Open drivers side window. •Close all doors, except the driver side door and check all doors are in the unlocked position. •Close driver side door and lock it using the key. All doors must lock automatically at the same time. •Now, unlock the driver side door, using the key and check that all doors unlock at the same time. •Push the driver side door button, down and check that all the other door buttons go down. •Switch Accessories power “On”, with the Grey wire connected to the brakes, the doors will lock. •Switch Accessories power “Off” and all doors will unlock. Flavio Alessio 15 November 2005
Central Door Locking p/n 900.705 Fitting Instructions Please note remove remotes from antenna before use
•Actuator wire colours •Blue •Green •White •Brown •Black
•Actuator wire colours •Blue •Green
5 wires Front Actuators
2 wires Rear Doors Actuators
For Vacuum Locking Cut this link to change locking pulse. Eg: Merc-Benz Do not cut when using electric actuators
Aux. output: Black/Red Current limited to 80 mA, negative switching.
Important! Use relay when connecting Boot or rear Hatch/Slide Door Actuator.
Yellow: to Accessories Red: 12V +
Fuse 15A
Grey to Foot Brake Switch (Negative Side)
Black: Negative
Pink:
Immobiliser function (10A) (If connected)
Orange: Indicator Lights Flavio Alessio 15 November 2005
For technical support call Siemens VDO 1800 335 282
Central Door Locking p/n 900.705 Fitting Instructions How to connect the immobiliser function
5 wires Front Actuators
2 wires Rear Doors Actuators
Black
Yellow: to Accessories + 12V Grey to Foot Brake Switch (Negative Side) Fuse 15A
Red:
Pink:
Immobiliser function
Orange: Indicator Lights
85
87a Starter Solenoid 87
30 Ignition + Flavio Alessio 15 November 2005
86 Cut starter motor solenoid wire from ignition barrel (+12V)
Central Door Locking p/n 900.705 Fitting Instructions Fig 1
Door Wiring
Bill Of Materials (Inside Kit Box) 1x Control Unit (ECU) 2+2x Actuators 2x Remote Control 1x Loom 1x Hardware Kit (4 self-tapers, 2 screws 1x metal block) 4x Bracket 4x Rods 1x Fitting Instructions Manual
Fig. 6
Central Door Locking p/n 900.705 Fitting Instructions FEATURES
•Programmable remote controls. •Indicator relay built in. •Starter immobilisation output available. ( Requires extra cut out relay) •Auxiliary output for boot release. •Extra lock/unlock outputs for Commercial vehicles already equipped with key operated central locking. •Two button remote control.
OPERATING INSTRUCTIONS BUTTON A
To lock doors When pressing button A once, the door will lock and the indicator lights will flash once.
BUTTON B
To Unlock doors Press button B once, the indicator lights will flash once and the doors will unlock.
BUTTON B
Auxiliary output channel ( Eg. Boot release ) Hold button B for two seconds and the boot release will unlock.
PROGRAMMING REMOTE CONTROLS There are two remote control, supplied in the kit, pre-programmed. Any additional remote control must be programmed separately, as follows:
A
•Power Off (by disconnecting the 15A fuse on the Red wire. •Switch On the accessory power and reconnect the 15A fuse (Red wire). •Switch, Off & On - Off & On - Off & On, the ignition key (3 times). •The indicator lights will flash once (it has entered the code learning mode). •Press the original remote control button A, once and the indicator lights will flash twice. •Press the new remote control button A, once and the indicator lights will flash three times. •Same procedures apply to a maximum of four remote controls. •After six seconds, from setting the last remote, the system will reset it self to normal function.
B
Flavio Alessio 15 November 2005
