Transcript
CF9030 ASSEMBLY
CF9030 ASSEMBLY PROCEDURES Step 1: Unpack carton. Tools Required: Knife or scissors; hammer; Philips or Robertson screwdriver
VERM ON CastTing
s
Box
#5
Box
Box
Box
#1
Box
#4
#3
#2
Use the knife or scissors to cut the strapping on the package, then lift off the cardboard cap. Remove the cardboard sleeve by lifting it straight over top of the barbecue. Remove and unpack the enclosed parts boxes. Carefully remove any protective covering from stainless steel parts. CAUTION: Some exposed edges may be sharp. Page 1 50001515 12/02 Rev.0 En
CF9030 ASSEMBLY
Step 2: Position main grill head. Required: Main Grill Unit.
Carefully lay the main grill unit on its back, using the flattened carton cap as a protective surface. This operation is best performed by two (2) people. Use of gloves is recommended. Ensure the front lid does not fall open while moving the unit. Allow the lid to rest partially open once the unit is on its back (Fig. 2).
Fig. 2
Step 3: Assemble legs to bottom panel. Required: (4) legs; the Bottom Panel; (8) 1/4-20 x 1 1/2” bolts
Assemble the four (4) legs to the bottom panel as shown, with two (2) bolts each. Tighten fully (Fig. 3).
Fig. 3
Page 2
CF9030 ASSEMBLY
Step 4: Assemble Legs to Grill Unit. Required: (8) 1/4-20 x 1 1/2” bolts
Position the leg assembly into the base unit until the two round bolt holes align with the thread inserts in the legs, as shown. Ensure the tank hole (on LP models) is at the right hand end of the grill. Assemble with two (2) bolts per leg, leaving the bolts loose by 3 or 4 threads. See Fig. 4.
Fig. 4
Step 5: Assemble casters. Caster
Required: (4) Casters
Push a caster into the bottom of each leg as far as possible. Ensure the casters are locked; i.e., the locking tabs are in the “down” position, as shown. Locking Tab on each caster to be in "down" position.
Carefully stand the grill upright while securing the front lid from falling closed. Again, two people are recommended for performing this.
Fig. 5
Page 3
CF9030 ASSEMBLY
Step 6: Install Front Panel. Required: the Front Panel; (4) Plastic Push-pins
Position the Front Panel between the front grill legs, aligning the two (2) holes in the side flanges of the panel with those in the legs. Push a pin into each hole as far as possible, It may be necessary to lightly tap the pins. See Fig. 6. (Push-pin) Fig. 6. (Back view of grill)
Step 7: Install Grease Cup, Cup Holder and Pan. Required: Grease pan, grease cup and grease cup holder
Fig. 7a
Assemble the cup holder into grease pan opening by squeezing the ends in slightly, then releasing. Place a grease cup into the holder, as shown in Fig. 7a. Position the grease pan into the back side of the grill just below the back panel—with the grease cup at the right end—on the two (2) support rails. Push the pan in squarely until it settles into the recesses of the supports (Fig. 7b).
Fig. 7b
Page 4
CF9030 ASSEMBLY
Step 8: Assemble side shelf brackets. Required: (2) right shelf brackets, (2) left shelf brackets, (4) spring clips Fig. 8a Push a spring clip over the underside end hole in each bracket, as shown (Figs. 8a and 8b). Attach a right and a left bracket over the leg attachment bolts, then push the brackets down fully (Fig. 8c). Tighten the four (4) bolts fully (Fig. 8d).
Fig. 8b
Repeat on the other side.
Fig. 8c
Fig. 8d
Step 9: Assemble side shelves. Required: (2) side shelves, (4) #10-24 x 1/2” bolts
Slot Tab View Rotated 90O
Fig. 9a
Assemble the side shelves to the brackets by positioning them halfway over the brackets, then sliding them towards the grill while pushing down firmly on the front edge. The slots at the front edge of the shelves should align with the tabs at the back of the shelf supports (Fig. 9a). Tap the shelf lightly, if necessary, to fully engage the slot and tab. Once aligned, fasten with a bolt through the spring clips (Fig. 9b).
Fig. 9b Page 5
CF9030 ASSEMBLY
Step 10: Install Internal Components. Sear Plates Cooking Grates
Required: (3) sear plates, (2) cooking grates, warming rack
Warming Rack Finger Hole
Refer to Fig. 10. Place the sear plates into the base unit ensuring that edges with the finger holes face the grill front, and the side edges face down. Position the cooking grates into the base similarly; these may be turned over to provide a flat surface for delicate foods. Set the warming rack into the two supports in the ends of the rear lid.
Fig. 10
Step 11: Install the LP cylinder (LP models only). Required: LP gas cylinder (not supplied) NOTE: Before lighting the grill, refer to the owner’s manual for proper cylinder specifications, filling requirements, regulator attachment and leak testing procedures.
Fig. 11
Page 6
CF9030 ASSEMBLY
21 15
26
20 14
17
27 6 31
28 5 32
22
23
8
7
16
29
25
24
10 9
11a, b
13a 3
12
1 2
4
30
19
18
Vermont Castings, Majestic Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice.
CF9030 Page 7
CF9030 ASSEMBLY
CF9030 (Items marked ‘*’ are not shown in the parts illustration) Ref. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11a. 11b. 12. 13a. 13b. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32.
Description Panel Bottom H3 Assem Leg H3 - Final Assem Front Panel H3-Blue Caster Base Assem H3 Lid Assem - Rear Blk H3 Flash Tube - H3 Support Grease Pan Gasket Burner HBQ Burner Main Assem HBQ Valve Assem - H3 Nat Valve Assem - H3 LP Console Assem H3 - 9030 Regulator H3 12’ Nat Gas Hose Hardware - Lid Set Lid Assem - Front H3 Blue Grease Pan H3 Cook Grates - H3 Enamel Bezel Knob - H3 Plate Heat - Enamel Warming Rack - H3 Enamel Grease Cup Grease Cup Holder - H3 Electrode - Main Short Electrode - Main Long Lid Bumpers Support Shelf L Black - H/VC Support Shelf R Black - H/VC Front Lip - H3 Ignitor - 3 Term & Knob Shelf Side H/VC Hardware Bag - H3
Qty. 1 4 1 4 1 1 1 2 3 3 1 1 1 1 1 1 1 1 2 3 3 3 1 1 1 1 2 4 2 2 1 1 2 1
Page 8
CF9030 50001310 50001317 50001295 50000090 50001462 50001279 50001300 50001302 50000892 50000835 50001439 50001438 50001440 50001308 50000198 50000355 50001430 50001301 50001314 50001327 50001455 50000877 50001311 50000126 50001319 50000071 50000072 50000177 50001418 50001419 50001482 50000358 50001509 50001390
