Transcript
CFD-V3/V7/V7L SERVICE MANUAL
Canadian Model UK Model Australian Model
Ver 1.5 2003.12 With SUPPLEMENT-1
CFD-V7
AEP Model CFD-V3/V7/V7L
E Model CFD-V3/V7
Photo : CFD–V7
Model Name Using
CD Section
CFD-S36
Similar Mechanism
Tape Section
CFD-S36
CD Mechanism Type
KSM-213CDP
Optical Pick-up Type
KSS-213C
Tape Transport Mechanism Type
MF-V5-117
SPECIFICATIONS CD player section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20 000 Hz +1/–2 dB Wow and flutter Below measurable limit
Radio section Frequency range CFD-V3/V7 FM Italy European countries Other countries AM Italy European countries Other countries CFD-V7L FM LW
87.5 - 108 MHz 87.6 - 107 MHz 87.6 - 108 MHz 526.5 - 1 606.5 kHz 531 - 1 602 kHz 530 - 1 710 kHz 87.6 - 107 MHz 153 - 279 kHz
IF FM: 10.7 MHz AM/LW: 455 kHz Aerials FM: Telescopic aerial AM/LW: Built-in ferrite bar aerial Cassette-corder section Recording system 4-track 2 channel stereo Fast winding time Approx. 120 s (sec.) with Sony cassette C-60 Frequency response TYPE I (normal): 80 - 10 000 Hz – Continued on page 2 –
CD RADIO CASSETTE-CORDER 9-873-079-16
Sony Corporation
2003L02-1 © 2003.12
Personal Audio Company Published by Sony Engineering Corporation
CFD-V3/V7/V7L Ver 1.4 2003.06
General Speaker Full range: 10 cm dia., 3.2 Ω, cone type (2) Outputs Headphones jack (stereo minijack) For 16 - 68 Ω impedance headphones Maximum power output 3.6 W Power requirements For CD radio cassette-corder: 120 V AC, 60 Hz (Canadian, E4 model) 230 V AC, 50 Hz (Except Canadian model) 110-120V AC/220-240V AC 50/60Hz changeable (E4 model) 9 V DC, 6 R20 (size D) batteries Power consumption AC 20 W Battery life For CD radio cassette-corder: FM recording Sony R20P: approx. 13.5 h Sony alkaline LR20: approx. 20 h Tape playback Sony R20P: approx. 7.5 h Sony alkaline LR20: approx. 15 h CD playback Sony R20P: approx. 2.5 h Sony alkaline LR20: approx. 7 h Dimensions Approx. 420 × 165 × 256 mm (w/h/d) (16 5⁄8 × 6 1⁄2 × 10 1⁄8 inches) (incl. projecting parts) Mass Approx. 4.1 kg (9 lb. 1 oz) (incl. batteries) Supplied accessory Mains lead (1) Design and specifications are subject to change without notice.
Information For customers in Europe
This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located at the bottom of the player. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
TABLE OF CONTENTS Specifications ............................................................................... 1
1. SERVICING NOTES ...................................................... 3 2. GENERAL Location and Function of Controls ....................................... 4
3. DISASSEMBLY 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7.
3-8.
Cabinet (Front) Sub ASSY, Cabinet (Rear) ................. 5 Control Board .............................................................. 5 Cabinet (upper) ............................................................ 6 Power Board, Inlet Board, BATT (R) Board, BATT (L) Board ........................................................... 6 Volume Board, FM SW Board, Main Board ............... 7 PRE Board, Mechanism Deck, Optical Pick-up Section, CD Board ............................. 7 Belt, M601 (Capstan / Reel Motor), “HRP901 Head, Magnetic (Record/Playback)”, HE901 Head (Erase) .................................................... 8 Optical Pick-up (KSS-213C) ....................................... 8
4. DIAL POINTER INSTALLATION .............................. 9 5. ADJUSTMENTS 5-1. Mechanical Adjustments ............................................ 10 5-2. Electrical Adjustments ............................................... 10
6. DIAGRAMS 6-1. 6-2. 6-3. 6-4. 6-5.
Explanation of IC Terminals ...................................... 13 Block Diagrams – Tuner/TC Section – ..................... 15 Block Diagrams – Main Section – ............................. 16 Block Diagrams – CD Section – ................................ 17 Printed Wiring Boards – Main Section – (Last digit :-11) ............ 18 6-6. Schematic Diagrams – Main Section (1/3) – (Last digit :-11) ............ 19 6-7. Schematic Diagrams – Main Section (2/3) – (Last digit :-11) ............ 20 6-8. Schematic Diagrams – Main Section (3/3) – (Last digit :-11) ........... 21 6-9. Printed Wiring Boards – Main Section – (Last digit :-12) ............ 22 6-10. Schematic Diagrams – Main Section (1/3) – (Last digit :-12) ............ 23 6-11. Schematic Diagrams – Main Section (2/3) – (Last digit :-12) ............ 24 6-12. Schematic Diagrams – Main Section (3/3) – (Last digit :-12) ........... 25 6-13. Printed Wiring Boards – Control/Power Section – (Except V7 :E4 model) ..... 26 6-13. Printed Wiring Boards – Control/Power Section – (V7 :E4 model) ................. 27 6-15. Schematic Diagrams – Control/Power Section – ...... 28 6-16. Schematic Diagrams – CD Section – ........................ 29 6-17. Printed Wiring Boards – CD Section – ...................... 30
7. EXPLODED VIEWS 7-1. 7-2. 7-3. 7-4. 7-5. 7-6.
Front Cabinet Section ................................................ 34 Rear Cabinet Section ................................................. 35 Upper Cabinet Section ............................................... 36 Mechanism Deck Section (1) .................................... 37 Mechanism Deck Section (2) .................................... 38 CD Block Section ...................................................... 39
8. ELECTRICAL PARTS LIST ...................................... 40
SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe more than 30 cm away from the objective lens.
CFD-V3/V7/V7L
LASER DIODE AND FOCUS SEARCH OPERATION CHECK 1. Press CD open knob. 2. Open the lid for CD. 3. Push on SWITCH (S801) as following figure. 4. Confirm the laser diode emission while observing the objecting lens. When there is no emission, Auto Power Control circuit or Optical Pick-up is broken. Objective lens moves up and down once for the focus search. Insert a precision screw driver and push SWITCH (S801)
CHUCK PLATE JIG ON REPAIRING On repairing CD section, playing a disc without the CD lid, use Chuck Plate Jig. • Code number of Chuck Plate Jig : X-4918-255-1
3
CFD-V3/V7/V7L
SECTION 2 GENERAL
This section is extracted from instruction manual.
LOCATION AND FUNCTION OF CONTROLS
REC PLAY REW
Inserting a cassette
FF STOP/EJECT PAUSE
Loading a CD
With the side you want to play facing upward
FM MODE (rear) PLAY MODE
c
Z PUSH OPEN/CLOSE
ENTER
With the labeled side up
Display
C Total track number VOLUME OPR/BATT
MEGA BASS
* FM MODE•ISS for CFD-V7L
i
u
TUNING
FUNCTION
x
D Track number
.,>
E Programmed track
4
CFD-V3/V7/V7L Ver 1.1 2001.04
SECTION 3 DISASSEMBLY z The
equipment can be removed using the following procedure.
Control board
Cabinet (front) sub ASSY
Power board, Inlet board, BATT (R) board, BATT (L) board
Set Cabinet (rear)
Cabinet (upper)
Volume board, FM SW board, Main board
PRE board, Mechanism deck, Optical pick-up section, CD board
Belt, M601 (capstan/reel motor), HRP901 Head, Magnetic (Record/playback), HE901 Head (Erase)
Note : Follow the disassembly procedure in the numerical order given.
3-1. CABINET (FRONT) SUB ASSY, CABINET (REAR)
8 Knob (vol )
Cabinet (front) sub assy 7 Screw +BVTP 3 × 12
Cabinet (rear)
5 4 Screw +BVTP 3 × 12 9
1 6 Open the Lid (CD)
Lid, battery case
3 Screws +BVTP 3 × 12
2 Screws +BVTP 3 × 12
3-2. CONTROL BOARD
Cabinet (front) sub assy
CONTROL board
3
2 Screws +BVTP 2.6 × 8
1 Screws +BVTP 2.6 × 8
5
CFD-V3/V7/V7L
3-3. CABINET (UPPER) 1 Screws +BVTP 3 × 12
5 Screw +BVTP 3 × 12
6 Screw +BVTP 3 × 10
3 Open the Lid (CD)
2 Open the Holder assy, cassette by pressing STOP/EJECT button.
Cabinet (upper)
STOP/EJECT button
4 Screw +BVTP 3 × 12
Remove the handle in the direction of the arrow.
8
9
7 CNP902 (POWER board)
Cabinet (rear)
3-4. POWER BOARD, INLET BOARD, BATT (R) BOARD, BATT (L) BOARD BATT (R) board
5 Screws +WH 3 × 8 6 CNP908
8 4 CNP907
CNP907
POWER board
3
7
1 Screws +BVTP 3 × 10
BATT (L) board INLET board 2 Screws +BVTP 3 × 10
Cabinet (rear)
6
CFD-V3/V7/V7L Ver 1.1 2001.04
3-5. VOLUME BOARD, FM SW BOARD, MAIN BOARD 4 Remove solder (four places)
5Screw +BVTP 3 × 10
0 Screws +BVTP 3 × 10
FM SW board 2Remove solder (five places)
MAIN board
qa
8CNP304
7 Wire, parallel (CN802) (15 core) 9Wire, parallel (CNP305) (10 core) (V3, V7) (12 core) (V7L)
6 KH801
S801
Cabinet(upper)
3 1 Screws +BVTP 3 × 10
VOLUME board
3-6. PRE BOARD, MECHANISM DECK, OPTICAL PICK-UP SECTION, CD BOARD 8 Screw +BVTT 2 × 6
CD board
0 Wire, parallel (CNP701) (16 core)
7 Remove solder (four places)
5 Screws +PWH 2.6 × 10 1 Screws +BVTP 3 × 10 9
3 Screw +BVTT 2 × 6
5 Screws +PWH 2.6 × 10
PRE board
4
1 Screw +BVTP 3 × 10
Optical pick-up section 6
Mechanism deck
2
Cabinet(upper)
7
CFD-V3/V7/V7L Ver 1.1 2001.04
3-7. BELT, M601 (CAPSTAN / REEL MOTOR), “ HRP901 HEAD, MAGNETIC (RECORD/PLAYBACK) ”, HE901 HEAD (ERASE)
HRP901 Head, Magnetic (Record/ Playback)
HE901 Head (Erase)
1 Screws +B 2.6 × 5
8
Mechanism deck 6
7 Claws
2 5 Claws
4 M601 (Capstan/reel motor)
3 Belt
3-8. OPTICAL PICK-UP (KSS-213C)
Optical pick-up (KSS-213C) Cover, CD Claws Gear
5
1
Claw
Claw 2
Claw
Chassis ASSY, motor (MB) (spindle) Shaft, sled 3 Bend the stopper 4
8
CFD-V3/V7/V7L
SECTION 4 DIAL POINTER INSTALLATION Note : Follow the installation procedure in the numerical order given. 1 Align the pointer with the groove of “cabinet (front) sub ASSY” and insert it as shown in the illustration. 2 Align knob (TU) with “cabinet (front) sub ASSY” and fasten the screw. Cabinet (front) sub ASSY
1 Pointer
knob (Tu)
2 Screw (+BVTP 2.6 × 8)
3 Turn the knob (TU) fully in the direction of the allow as shown in the illustration. 4 Turn the tuning capacitor gear fully in the direction of the allow as shown in the illustration. 5 Fasten the “cabinet (front) sub ASSY” and cabinet (rear) with the screws.
5
4 Tuning capacitor gear
Cabinet (rear)
3 Tuning knob
9
CFD-V3/V7/V7L
SECTION 5 ADJUSTMENTS
5-1. MECHANICAL ADJUSTMENTS
Adjustment Location : Mechanism deck
PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened swab : record/playback head pinch roller erase head rubber belts capstan 2. Demagnetize the record/playback head with a head demagnetizer. (Do not bring the head demagnetizer close to the erase head.) 3. Do not use a magnetized screwdriver for the adjustments. 4. The adjustments should be performed with the rated power supply voltage (9V) unless otherwise noted. Torque Measurement Torque
Torque Meter
Forward
CQ-102C
Forward Back Tension
CQ-102C
Fast Forward
Meter Reading 1.77 – 5.88 mN•m (18 – 60 g•cm) (0.25 – 0.83 oz•inch) 0.1 – 0.49 mN•m (1.0 – 5.0 g•cm) (0.014 – 0.069 oz•inch) 4.42 – 9.31 mN•m (45 – 95 g•cm)
CQ-201B
Rewind
(0.62 – 1.32 oz•inch) 4.42 – 9.31 mN•m (45 – 95 g•cm) (0.62 – 1.32 oz•inch)
CQ-201B
Tape Tension Measurement Torque Meter
Meter Reading more than 60g (more than 2.12 oz)
CQ-403A
Tape speed adjustment control inside motor
TUNER SECTION
0dB = 1 µV
AM Section Function switch : AM or LW Volume : MIN AM RF signal generator
Put the lead-wire antenna close to the set.
5-2. ELECTRICAL ADJUSTMENTS TAPE RECORDER SECTION
0dB = 0.775V
Standard Output Level Output terminal load impedance output signal level
HP OUT 32 Ω 0.25V (–10dB)
Test Tape Type WS-48A
Signal 3kHz, 0dB
Used for Tape Speed Adjustment
Tape Speed Adjustment Procedure : Mode : Playback digital frequency counter
test tape WS-48A (3kHz, 0dB)
FM Section Function switch : FM Volume : MIN FM RF signal generator 0.01µF
22.5kHz frequency deviation by 1kHz signal. Output level : as low as possible
level meter
32Ω
32Ω set
set
J301 (phones)
Adjustment Value : 3,000Hz Standard Value : 2,940 - 3,060Hz Frequency difference between the beginning and the end of the tape should be within 1.5% (45Hz).
10
30% amplitude modulation by 400Hz signal. Output level : as low as possible
J301 (phones)
telescopic antenna terminal
CFD-V3/V7/V7L
R
C8 C8
JC310
) : V3/V7: AEP, UK, CET, SP,KR > : V7:Italian ] : V7L
R816 R815 R814 R813
AM/LW IF ADJUSTMENT Adjust for a maximum reading on level meter. 455kHz
JW316 JW317 JW318
R812 R811
EXCEPT V7L
-1 -2
R810 21
IC801
S351
R809
AM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. L4 520kHz ( 520kHz) < 516kHz>
LW TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. L3 160kHz CT3, CV3 260kHz
• RF Signal Reference Waveform (eye pattern) VOLT/TV : 200mV TIME/DIV : 500 nS
RF level 0.7 – 1.0 Vp-p (LPC ON) 1.0 – 1.4 Vp-p (LPC OFF)
FM IF ADJUSTMENT Adjust for a maximum reading on level meter. 10.7MHz
FM FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. L2 86.5MHz ( 87.0MHz) < 87.35MHz> [ 87.0MHz] CT2 109.5MHz (108.3MHz) <108.25MHz> [108.3MHz]
When observing the eye pattern, set the oscilloscope for AC range and raise certical sensitivity oscilloscope (AC range) TP (RF)
FM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. 86.5MHz ( 87.0MHz) < 87.35MHz> [ 87.0MHz] 109.5MHz (108.3MHz) <108.25MHz> [108.3MHz]
JW710 R709
R710 R711
C705 R704
TP (RF)
C703 C736
9
R706 R701 R705 R703 R702
CD SECTION How to put the set into CD Test Mode 1. Set the function switch to power off. 2. Set the function switch to CD. 3. Set Test mode by momentarily shorting both of the IC801 51pin to GND. (Shorting the terminals momentarily is sufficient). The set is into CD test mode (88 is displayed). 4. Turn the power off to release test mode.
R708
Adjustment Location : Main board (See page 12)
(GND) [CD BOARD] (Conductor side)
C734
L1 CT1
Focus Bias Check 1. Connect the oscilloscope between TP (RF) and GND on CD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3. Press the 7 button two times (LPC ON). 4. Confirm that the oscilloscope waveform is as shown in the figure below. (eye pattern) A good eye pattern means that the diamond shape (◊) in the center of the waveform can be clearly distinguished.
JW
LW FREQUENCY COVERAGE ADJUSTMENT Adjust for a maximum reading on level meter. L4 145kHz CT4, CV2 300kHz
CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias.
R730
C731
JW726
C743
V7L
T1
TEST mode : momentarily short
C730 J
R729 C747
C703 C744 C
IC701 C
42
L3 CT3
GND
1,780kHz (1,680kHz) <1,630kHz> AM TRACKING ADJUSTMENT Adjust for a maximum reading on level meter. 620kHz 1,400kHz
51pin
C704
CT4
320
C810
T2
( < [
R851 C801
• Abbreviation CET : East European & Russian SP : Singapore
[MAIN BOARD] (Conductor side) C844
• Repeat the procedures in each adjustment several times, and the frequency coverage and tracking adjustments should be finally done by the trimmer capacitors.
11
CFD-V3/V7/V7L
Adjustment Location :
[MAIN BOARD] (Component side)
L3: AM/LW Tracking Adjustment
T1 : FM IF Adjustment
T2 : AM/LW IF Adjustment
CV2 : LW Frequency Coverage Adjustment (V7L) L2 : FM Frequency Coverage Adjustment
L1 : FM Tracking Adjustment L4 : AM/LW Frequency Coverage Adjustment CV3: LW Tracking Adjustment (V7L)
[MAIN BOARD] (Conductor side)
CT2 : FM Frequency Coverage Adjustment CT4: AM/LW Frequency Coverage Adjustment
CT1 : FM Tracking Adjustment
CT3 : AM/LW Tracking Adjustment
12
SECTION 6 DIAGRAMS
CFD-V3/V7/V7L
6-1. EXPLANATION OF IC TERMINALS IC801 µPD789316GK-903 SIGNAL PROCESSOR, D/A CONVERTER, LCD DRIVE, SYSTEM CONTROL Pin No. 1–4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 – 21 22 – 25 26 – 43 44 – 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Pin name NC IC XT1 XT2 VDD VSS CL1 CL2 RESET NC SYNC–R CE C–RST CAPH CAPL VLC0 – 2 COM0 – 3 S0 – 17 S18 – 22 S23 ENTER MODE PLAY FR FF STOP DOOR WRQ TEST MUTE FSEQ DRF DO DIN CLK
I/O — — I — — — I — I — — O O — — — O — O — I I I I I I I I I O I I O I I
Description Not used (open) Connect to ground. Connect to ground. Not used (open) Power supply terminal (B+ 3.3 V) Ground terminal Oscillator terminal (4 MHz) Oscillator terminal (4 MHz) Reset signal input Not used (open) Not used (open) Chip enable signal output Reset signal output to the LC78645E (IC701) Charge pump capacitor terminal Charge pump capacitor terminal Capacitor connect terminal LCD common drive output Not used (open) LCD segment drive output Not used (open) Key (ENTER) input Key (MODE) input Key (H PLAY) input Key (l FR) input Key (L FF) input Key (s STOP) input Door open/close input Command signal input Test mode signal terminal input (TEST: L) Mute signal output Frame SYNC signal input DRF (Defect RF) input Serial data output Serial data input Clock signal input
13
CFD-V3/V7/V7L
• Circuit Boards Location
PRE board INLET board POWER board
BATT (R) board
BATT (L) board
VOLUME board
FM SW board
CONTROL board MAIN board CD board
14
CFD-V3/V7/V7L
Ver 1.5
6-2. BLOCK DIAGRAMS –TUNER/TC SECTION– ANT1 FM TELESCOPIC ANTENNA TU +6V
T1 FM IF
FM/AM FRONT-END IF AMP,DET,FM MPX
IC1 RF IN
D1
D2
CT1,L1 FM TRACKING CT2,L2 FM FREQUENCY COVERAGE
V7L
EXCEPT V7L CT3,L3 AM TRACKING
CV3,CT3,L3 LW TRACKING
L3 AM/LW FERRITE-ROD ANTENNA
CT1
L1 FM RF
FM FRONT-END
QUAD
T2 AM IF
MIX OUT
L OUT
FM IF IN
CF2
FM DET
MPX IN
DET OUT
MPX
R OUT
R-CH
CV1-1 FM RF OUT TU +6V
CT2
L2 FM OSC
FM OSC
CV1-2
AM RF IN V7L CV3
CT3
LPF2
AM IF IN
CF1
LPF1 S1 EXCEPT V7L
AM DET
FM MODE MONO
TU +6V
AM FRONT-END
-11 STEREO
CV1-3 Q2
-12
Q1
TU +6V V7L
FM MODE ISS MONO 1
AM OSC CV2,L4,CT4
L4,CT4
LW FREQUENCY COVERAGE
L4 AM OSC
AM FREQUENCY COVERAGE
CV2
CT4
STEREO 2
CV1-4
V7L
TU +6V
PRE/REC AMP
V7L ISS
IC301 MUTE
CD SECTION
TU IN L CD IN L
CD L-CH CD R-CH
22 24
R-CH
MONITOR AMP L.LO
BUFFER
L.LINE L.RAD
TAPE
L.OUT
MAIN SECTION
(7dB)
MIC AMP 13
L.OUT
20
MIC
MUTE
HRP901 RECORD/ PLAYBACK HEAD
5
PB AMP L.IN
PB AMP
FM
REC AMP(26dB) 4 HE901 ERASE HEAD
L.RO
LINE ALC 1
LOGIC
DET
REG REF 6
TAPE
CD
17
TAPE
15
CD
MAIN SECTION
• R-CH is omitted: same as L-CH
TAPE
• Signal path. F : FM f : AM E : PLAY a : REC J : CD
REC 21 T301
BIAS OSC Q301
• IC link button. V7L
S301 REC
-1
-11 Last digit : -11
-2 ISS1 Q303
TU +6V PB
15
15
-12 Last digit : -12
CFD-V3/V7/V7L Ver 1.5
6-3. BLOCK DIAGRAMS –MAIN SECTION– POWER AMP
IC304 TUNER/TC SECTION
J301
R-CH
L.OUT S355
-11
RV352
MEGA BASS ON
MUTE Q101
VOLUME
STANDBY SWITCH
-12 SP101 SPEAKER (L-CH)
OFF R-CH
SP201 SPEAKER (R-CH)
D302
CD SECTION
CD +3.3V
RESET Q801
RESET
D309
FM TAPE
TUNER/TC SECTION
D314
D303 D304
E4
VOL SEL BOARD
CD TU +6V TAPE +6V
S351-1 FUNCTION EXCEPT V7L AM FM LW
-1 -2
+3.3V REG Q310, D308
CD+ 3.3V
POWER SWITCH Q311,312
+6.9V REG Q309, Q311
S901 VOLTAGE SELECTOR 220-240V AC R 110-120V AC
CD
V7L
CD +6V F901
F901
T901 POWER TRANSFORMER
CNJ901
RESET
(4MHz)
EXCEPT E4
AC IN
CL1 CL2
S801 CD DOOR (OPEN/CLOSE)
D901-904 DOOR
DIGITAL SIGNAL PROCESSOR, LCD DRIVE, SYSTEM CONTROL
POWER AMP B+ (+8.9V)
VOLTAGE DET
POWER SWITCH Q402,Q405
STOP
FF
FR
PLAY
MODE
ENTER
S22
S18
44
D310 OPR/BATT
S0-S4
COM3
COM0
_ _ COM0-3
_
48
_
25
9V AC 4.5V
IC401 -12
IC801(1/2)
22
-11
S601 (MD POWER)
INITIAL SWITCH Q401 LCD401 LIQUID CRYSTAL DISPLAY
M601 CAPSTAN/REEL MOTOR
S404
S406
S405
ENTER
PLAY MODE
S403
S402
Q409 MOTOR SWITCH
S401
DRY BATTERY SIZE "D" (IEC DESIGNATION R20) 6PCS,9V
• R-CH is omitted: same as L-CH • Signal path. F : FM • IC link button
CD CONTROL
-11 Last digit : -11 -12 Last digit : -12
16
16
CFD-V3/V7/V7L
Ver 1.5
6-4. BLOCK DIAGRAMS –CD SECTION– CD RF/ SYSTEM SERVO PROCESSOR
OPTICAL PICK-UP BLOCK (KSS-213C)
IC701 REF
VC
A
FIN1
B
RF
+
FIN2
EFMIN
DIGITAL FILTER/ ERROR CORRECTION
LCHO D/A
CD L-CH
RCHO
CD R-CH
TUNER/TC SECTION
-
C DRF D
E
TIN1
F
TIN2
RES +
TE FE
WRQ
LASER POWER CONTROL Q701
LD LD G
LDD
SERVO CONTROL
APC
PURPOSE PORT
COMMAND INTERFACE
DO DI CL CE
VREF
VC
PD
XOUT
XIN
CONT1 CONT2 CONT3
TDO FDO SPDO SLDO
VR
CONT4 CONT5
FSEQ LDS
PD
SLED/SPINDLE MOTOR DRIVE, TRACKING/FOCUS COIL DRIVE
IC702 RESET
X701 33.86MHz
VREF
MAIN SECTION
LEVEL SHIFT
T-
TIN
LEVEL SHIFT
T+ TRACKING COIL
FIN
F-
FSEQ CE CLK DIN DO WRQ C-RST DRF
F+ FOCUS COIL
MUTE DRIVER
-
+
SL-
SLIN
SPIN
S701 (LIMIT)
-11 -12
IC801(2/2)
SP+ SP-
RST
-
DIGITAL SIGNAL PROCESSOR, LCD DRIVE, SYSTEM CONTROL
SL+
LEVEL SHIFT
M701 SPINDLE MOTOR
+
LEVEL SHIFT
M702 SLED MOTOR
MUTE
• Signal path. J : CD • IC link button
SW
-11 Last digit : -11 -12 Last digit : -12
17
17
CFD-V3/V7/V7L Ver 1.2 2001.08
6-5. PRINTED WIRING BOARDS – MAIN SECTION – (Last digit : -11) 2
4
KH2 JC1 JC2 JC4
C8
R4 Q1
JW334
JW330
L3 AM/LW FERRITE-ROD ANTENNA
FM SW BOARD
R253 C252 C152 C156
C123
11 1-680-679- (11)
V3/V7
RV352 VOLUME
Semiconductor
Q409
D301
JW306
C153
C351
R418
LW
Q101 Q201
R386 R343
JW322
JW323
IC304 R251 R151 C253 KH306
D310 OPR/BATT
A-1 A-1 D-8 E-6 D-4
D304 D306 D308 D309 D310
D-4 D-9 C-5 D-4 E-7
D311 D314
D-7 E-4
IC1 IC304 IC401 IC801
C-3 E-7 D-8 D-5
Q1 Q2 Q101 Q201 Q309
B-3 C-3 E-7 E-7 D-7
Q310 Q311 Q312 Q401 Q402
C-5 C-6 C-6 E-9 E-8
Q405 Q409 Q801
E-8 C-8 D-5
SP101 SPEAKER (L-CH) SP201 SPEAKER (R-CH)
R417 CNP303
R254 C316
D1 D2 D301 D302 D303
Q401
R342
C254
Location
B R413 C E
E C B
R154
C154
JC305
R416
Q405 JC401
JW303
AM
C402
Ref. No.
1-680-676-
11 (11) J301 i
V7L
FM
S355 MEGA BASS
CD
rOFF V7L
IC401
C155
S351 FUNCTION TAPE CD/RADIO OFF V3/V7
R401
R403
JW305
R414 R415
Q402
R344 R340 R341
B CONTROL BOARD CN401
JC303
C255 JW304
-1 -2
R223 C224 R224 R124
RV352
S355
T
FM MODE ISS STEREOt MONO 1 2
R123 C124
1-680-678S1 FM MODE STEREOtMONO
C223
R404
C256
S351
D302
11 (11)
R401 C401 R346 R345
JW318
VOLUME BOARD KH307
KH902 D306
Q309
JW319
S1
F
JW307
4
1
C343 D311
E KH1
JW309
JW308
INLET BOARD CNP902
R402 JC302
R801
R809
CN801
R319
JW313
JW317
R810
C
JW314
JW316
R812 R811
IC801
MOTOR
-
JW301
D314
M601
C341
C347
R816 R815 R814 R813
JW328
D303
ANT1 FM TELESCOPIC ANTENNA
JW312 Q312
JC310
C314 R11
R349
R851
L1
1
JW302
C23
C36
1 CNP304
C851 C802
C810
D
L4
CV1-1 CV1-3
C32 V3/V7:AEP, CET,UK,SP,IT/ V7L R20
CV3
4
+
M CAPSTAN/REEL
C349
JW315
C801
JW332
C12
C320
S601 (MD POWER)
ICP301
C805 C841
IC1
JC5
C1
CT3
CT1
R355 R354 Q311
JW324
C844
24 R3
1
D309
C13
C29
C11
JC306
JW320
V3/V7
C24 R1
CNP305
V7L
11 12
9
R153
C31
2
R360
Q310
5
JW321
CT4
1
R353 R352 R351
C28 CT2
20
5
JW326
CV1-2 CV1-4
L2
C3 C25
C346
JW325
CV-1
JW327
R30
C21
R806
V7L
C14
15
C348
V7L
V3/V7
C843 C842
Q2
10
C22 C26
C4
CV2
Q801
CF2 12
JW311 JW310
C27
R2
C
V7L
4 3 2
D308 C345
V3/V7:AEP, CET,UK,SP,IT/ C20 V7L 13
JW333
D
R819 R818 R805
C10
V3/V7:AEP, CET,UK,SP,IT/ CF1 V7L
TC BOARD CN303
JW329
C7 JC7
C19
C15
C30
T2
JW331
C18
C17
B
JC6
9
C271
CN802
C891
C2
8
C9
C317
R8 JW335
T1
7
CD BOARD CNP702
C6
KH801
6
C171
C5
S801
5
z
A
R9
D1
3
S801 CD DOOR (OPEN/CLOSE)
MAIN BOARD
D2
A
Refer to page 14 for Circuit Boards Location.
D304 R314 R315
1
z
RON
18
18
Note: • X : parts extracted from the component side. • : Pattern from the side which enables seeing. • Abbreviation CND : Canadian IT : Italian CET : East European & Russian SP : Singapore AR : Argentina AUS : Australian TW : Taiwan KR : Korean
CFD-V3/V7/V7L 6-6. SCHEMATIC DIAGRAMS – MAIN SECTION (1/3) – ( Last digit : -11)
z
Refer to page 30 for Notes.
z
Refer to page 31 for IC Block
V3/ V7:AEP,CET, UK,IT/ V7L L3 AM/LW FERRITE-ROD ANTENNA C5 10p
C6 5p
R3 3.3k C11 10p
V7L
C12 10p
C29 100p C31 470p C28 470p
CV1-4 CT4
C7 *
CV1-2 CT2
CV3 50p
L1
C36 10p
C32 4.7p CV1-1 CT1
CV1-3 CT3
V7L
V7L
V3/V7
V7L
CV2 30p
L2
L4
JC7
C21 4.7p
V3/V7
R20 *
V3/V7
V7L
V7L
C25 100p
V3/V7
C15 0.1
C22 1
C17 0.1
R4 3.3k
C26 4700p
Q1 KRA302-RTK SWITCH
C18 1
JC5 0
JC4 100
*
FM/AM/LW FRONT-END,IF AMP, DET,FM MPX
QUAD
GND
TUN LED ST LED
C30 2p
C2 10p
R1 220
C8 4.7 50V
STEREO FM MODE ISS
C10 4700p
R2 330
C13 0.47
C14 4.7
ISS1 TU.L TU.R
C9 4.7 50V
C27 4700p
CF2
R9 22k
CF1
T1
R8 22k
C19 *
FM R11 10k
C20 *
TU.GND R30 220
C23 10 50V
1
FM MODE MONO
STEREO 2
V3:AEP,CET,SP/ V7:AEP,CET, UK,SP,IT/ V7L
JC6 0
1
S1
IC1 TA2111N
T2 D2 1SS355T-77
KH1 4
MONO 1
C1 1000p
D1 1SS133T-77
KH2 4
JC1 0
R-OUT
L-OUT
LPF1
LPF2
DET OUT MPX IN
AFC
0.01uF 0.01uF 100
VCC AM IF IN FM IF IN
4.7PF 0.01uF 0.01uF 1k
AM OSC
4.7PF 0.01uF 0.01uF 1k
V7L FM OSC
2.2PF 0.022uF 0.022uF 1k
V7:IT
FM-RF IN RF GND AM LOW CUT MIX OUT AGC
C7 C19 C20 R20
JC2 0
V3:AEP,CET,SP/ V7:AEP, CET,UK,SP
AM RF IN FM RF OUT RF VCC
V3:AR/ V7:CND,AR AUS,TW
ANT1 FM TELESCOPIC ANTENNA
Q2 KRA302-RTK SWITCH
C3 0.01
C24 0.01
TU +B
C4 22 S-GND
19
19
CFD-V3/V7/V7L Ver 1.1 2001.04 6-7. SCHEMATIC DIAGRAMS – MAIN SECTION (2/3) – ( Last digit : -11)
S355 MEGA BASS ON
C124 4700p
R124 6.8k
z
Refer to page 30 for Notes.
C224 4700p
OFF
R224 6.8k C223 0.47 50V R223 1k
C123 0.47 50V R123 1k
CNP305 12P
Refer to page 33 for IC Block Diagram.
RV352 VOLUME RV352(2/2) 20kB
5
1
5
1
IC304 BA5417
KH307 5P POWER AMP KH306 5P
R251 4.7k
CD
JC310 0
Q101 KRC410-RTK
Q201 KRC410-RTK
4
R253 470
C351 47 10V
CNP303 4P
+ -
C153 47 10V
R153 470
TAPE CD RADIO OFF
V7L
V3/V7 AM FM LW V7L
C152 1000p
S351-1 FUNCTION
JC306 0
C253 47 10V
R151 4.7k
C252 1000p
TU_IN_L TU_IN_R CD_IN_L CD_IN_R L_OUT R_OUT CD TAPE 6V GND SYNC-R ISS1
RV352(1/2) 20kB
z
+ 1
C254 470 10V
C154 470 10V
R254 100 J301
C317 22 25V
R315 1k
R319 4.7k
TAPE CD RADIO OFF Q309 2SD2396K +6.9V REG
JC401 0
ICP301
D308 KTZ 3.9-RTK
C347 220 10V
1k
1k 1k 1k 1k Q312 KRC405 RTK
R346
1k C345 0.01
R352 R353 R354 R355
C348 100 10V
R351
C346 0.01
R345 1k
R360 100k
D311 KDZ 7.5-RTK
C271 10 50V
R349 330
CD KH902 4P 1
C349 10000p
4
Q405 KTA1266-GR-AT Q311 KTB1241Y-AT
C171 10 50V
S351-2 FUNCTION AM V3/V7 FM LW V7L
R154 100
C255 0.1
C320 0.022
R314 4.7k
Q310 KTC3203Y-AT +3.3V REG
C155 0.1
Q401 KTA1266-GR INITIAL SWITCH R418 10k
R413 4.7k R416 4.7k
Q311,312 +B SWITCH
R414 6.8k R415 6.8k
OPR/BATT
P.GND R-OUT L-OUT UCOM-GND TU-GND TU +B D.GND CD 6V CD 3.3V AU MUTE
C341 3300 16V
JC303 0
VCC CONT N.C. TC N.C. VM VOUT GND
R402 10k
R404 1k
R401 100k
D306 1SS355TE-17
JC302 0 R403 22k
Q409 KTC3203Y-AT MOTOR SWITCH
S601 (MD POWER)
20
R344 220
VOLTAGE DETECT
Q402,405 POWER SWITCH
4
20
R343 3.3k
D310 L-34HD
Q402 KRC402
C402 10 50V C343 0.01
R386 3.3k
R417 10k
IC401 MM1468XD
R342 3.3k R341 3.3k R340 3.3k
C314 47 10V
C156 47 10V
D301 1SS355TE-17
JC305 0
D302 1SS355TE-17
D314 1SS355TE-17
D304 1SS355TE-17
D303 1SS355TE-17
D309 1SS355TE-17
ISS1 TU.L TU.GND TU.R FM TU +B S-GND
C256 47 10V
Q101,201 MUTE
C316 1 50V
1 CNP304 4P
M601 CAPSTAN/REEL MOTOR
C401 100 10V
GND 9V AC 4.5V
SP201 SPEAKER (R-CH) SP101 SPEAKER (L-CH)
CFD-V3/V7/V7L 6-8. SCHEMATIC DIAGRAMS – MAIN SECTION (3/3) – ( Last digit : -11)
z
Refer to page 30 for Notes.
z
Refer to page 13 for Explanation of IC Terminals.
R811 10k CN802 15P
P.GND
R809 1k
C810 100p
1
R810
100
R812
1k
STOP
R813
1k
FF
R814
1k
FR
R815
100
PLAY/PAUSE
R816
100
PLAY MODE
16
CD6V FSEQ DRF DO
5
*WRQ CL
10
CE DI *RES
10
COM0 COM1
CD3.3V U-RESET 15
C801 0.1
D.GND
S17
XT2
S16
VDD
S15 S14
DIGITAL SIGNAL PROCESSOR LCD DRIVER SYSTEM CONTROL
RESET
S13 S12 S11 S10
R806 220
C844 0.1
CD 6V AU MUTE
1
C891 1000p
KH801 2P
21
21
S6
S5
S4
S3
S2
S1
S0
COM3
COM2
COM1
VLC2
VLC1
S7
VLC0
S8
C-RST
CAPL
S9
CE
CAPH
SYNC-R
P.GND
2
S23
IC801
C843 0.1
CD 3.3V
ENTER
S18
C842 0.1
L-OUT
PLAY
S3
IC
Q801 KRC404-RTK RESET
TU +B
MODE
S19
C841 0.1
R-OUT
FF
S2
NC
R819 100
TU-GND
FR
S20
CL2
R818 100
UCOM-GND
STOP
S1
NC
NC
C805 0.1
WRQ
S0
S21
VSS
R851 4.7k
COM3
NC
CL1
C851 22p
5 S22
COM0
C802 47 10V
R801 22
COM2
NC
XT1
R805 220k
DOOR
TEST
FSEQ
DO
MUTE
D.GND
DRF
L-CH
DIN
CLK
R-CH
S801 CD DOOR (OPEN/CLOSE)
ENTER GND
1 CN801 16P
S4
CFD-V3/V7/V7L Ver 1.4 2003.06
6-9. PRINTED WIRING BOARDS – MAIN SECTION – (Last digit : -12) (Added V7: E4, KR model) z Refer to page 14 for Circuit Boards Location. 2
1
A
3
4
S801 CD DOOR (OPEN/CLOSE)
MAIN BOARD
5
6
7
8
9
z
A
CD BOARD CNP702
Semiconductor Ref. No.
C171 C8
C9
R11
JW328
D303
ANT1 FM TELESCOPIC ANTENNA
D314
FM SW BOARD
IC801 CN801
R319
R809
C256
JW316 JW318
-1 -2
C123
12 1-680-679- (12)
RV352 VOLUME V7L
R124
RV352
S355
CONTROL BOARD CN401 (EXCEPT V7:E4) CONTROL BOARD CN401 (V7:E4)
Q409
D301
C153
B
EXCEPT V7L
AM
LW
Q101 Q201
R386 R343
JW322
B
S351 FUNCTION TAPE•CD/RADIO OFF
R418
R416 R413
B C E
E C B Q405 JC401
IC304 R251 R151 C253 KH306
C254
D310 OPR/BATT
V7L
D304 D305 D306 D308 D309
D-4 C-5 D-9 C-5 D-4
D310 D311 D314
E-7 D-7 E-4
IC1 IC304 IC401 IC801
C-3 E-7 D-8 D-5
Q1 Q2 Q101 Q201 Q309
B-3 C-3 E-7 E-7 D-7
Q310 Q311 Q312 Q401 Q402
C-5 C-6 C-6 E-9 E-8
Q405 Q409 Q801
E-8 C-8 D-5
SP101 SPEAKER (L-CH) SP201 SPEAKER (R-CH)
CNP303
R254 C316
A-1 A-1 D-8 E-6 D-4
Q401
R417
R154
C154
D1 D2 D301 D302 D303
1-680-676-
12 (12) J301 i
FM
S355 MEGA BASS
CD
rOFF
Note: • X : parts extracted from the component side. • : Pattern from the side which enables seeing. • Abbreviation CND : Canadian IT : Italian CET : East European & Russian SP : Singapore AR : Argentina AUS : Australian TW : Taiwan KR : Korean
T
FM MODE ISS STEREOt MONO 1 2
EXCEPT V7L
C223
R123 C124
1-680-678S1 FM MODE STEREOtMONO
12 (12)
C402
R342
S1
IC401
C155
R344 R340 R341
JW323 R223 C224 R224
KH307
R403
JW303
D302
R415
R401
JW305
C351
IT KH1
R404 JC303
Q402
JW319
VOLUME BOARD
R401 C401
C255 JW304
C156
S351
E
F
R253 C252 C152
JW317
R810
KH902 C343 D311 EXCEPT IT R346 R345
R402 JC302
R801
JC310
R812 R811
C 4
1
INLET BOARD CNP902 (EXCEPT V7:E4) INLET BOARD CNP902 (V7:E4) JC305
C347
Q309
R816 R815 R814 R813
MOTOR
-
D306
R350
JW308
RON
22
22
Location
M601
C JW306
R349
R353 R352 R351
JW325
C314
1
JW314 JW313
JW307
L1
+
M CAPSTAN/REEL
C341
C851 C802
R851
1
S601 (MD POWER)
JW302
C36
4
CNP304
JW312
JW315
C805
C320
R153
V3:AEP,CET,SP/ V7:AEP,CET,UK, R20 C23 SP,IT,KR/V7L
D
CV3
L4
CV1-1 CV1-3
C32
4 3 2
C349
JW320
C12
JW324
CT3
CT1
11 12
9
CNP305 JC306 Q312 EXCEPT IT R348 R354
JW321
JW332
24 R3
2
C810
IC1
C29
C11
5
Q311
C801
C1
C31
R819 R818 R805
1
CT4
Q310
C841
C13
C28
R806
R1
CV1-2 CV1-4 CT2
20
1
R360
JW326
C3 C25 5 C24
CV-1
L2
JC5
R30
C21
V7L
C348
D305
C843 C842
C26
V7L
C14
15
C346
EXCEPT V7L V7L
CV2
Q801
Q2
10
C22
C4
C
CF2 12
EXCEPT V7L
CF1
C844
R2
V7L
D309
T2
C27 V3:AEP,CET,SP/V7:AEP, C20CET,UK,SP,IT,KR/V7L 13
JW327
JW333
TC BOARD CN303 (V7:E4)
D
C7 JC7
C19 C10
V3:AEP,CET,SP/V7:AEP, JC6 CET,UK,SP,IT,KR/V7L
JW329
D308 C345
L3 AM/LW FERRITE-ROD ANTENNA
TC BOARD CN303 (EXCEPT V7:E4)
JW301
JW330
C15
C30 C2
D
C18
C17
T1
JW331
JW309
Q1
JW334
D304 R314 R315
C891
JW311 JW310
R4
B
C271
CN802
JW335
C317
R8
C6
KH801
C5
JC2 R5
S801
R9
D1
D2
KH2
CFD-V3/V7/V7L
Ver 1.4 2003.06
6-10. SCHEMATIC DIAGRAMS – MAIN SECTION (1/3) – ( Last digit : -12)
z
Refer to page 30 for Notes.
z
Refer to page 31 for IC Block
V3: AEP,CET,SP/ V7:AEP,CET, UK,IT,SP,KR/ V7L L3 AM/LW FERRITE-ROD ANTENNA C5 10p
C6 5p
V7L
C12 10p
C31 470p C28 470p
CV1-4 CT4
R3 3.3k C11 10p
V7L
C29 100p
C7 *
CV1-2 CT2
CV3 50p
L1
C36 10p
CV1-1 CT1
CV1-3 CT3
V7L
EXCEPT V7L V7L
C32 4.7p
CV2 30p
L2
L4
JC7
C21 4.7p
EXCEPT V7L
R20
EXCEPT V7L
1k EXCEPT V7L 100 V7L
V7L
V7L
C25 100p
EXCEPT V7L
C15 0.1
C22 1
C17 0.1
R4 3.3k
C26 4700p
Q1 KRA302-RTK SWITCH
C18 1
JC5 0
R5 100
* R-OUT
L-OUT
LPF1
LPF2
DET OUT MPX IN
QUAD
GND
C30 2p
C2 10p
R1 220
C8 4.7 50V
JC6 0
R2 330
C10 4700p
ISS1
C9 4.7 50V
C27 4700p
R9 22k
CF1
T1
R8 22k
C19 *
FM R11 10k
C20 *
TU.GND R30 220
C23 10 50V
STEREO FM MODE ISS
TU.L TU.R
CF2 C14 4.7
1
C3 0.01
C24 0.01
TU +B
C4 22 S-GND
23
23
EXCEPT V7L
FM MODE MONO
MONO 1
V3:AEP,CET,SP/ V7:AEP,CET, UK,SP,IT,KR/ V7L
C13 0.47
1
S1
STEREO 2
T2 D2 1SS355T-77
KH1 4
JC1 0
C1 1000p
D1 1SS133T-77
KH2 4
IC1 TA2111N
TUN LED ST LED
FM/AM/LW FRONT-END,IF AMP, DET,FM MPX
AFC
0.01uF 0.01uF
VCC AM IF IN FM IF IN
4.7PF 0.01uF 0.01uF
AM OSC
4.7PF 0.01uF 0.01uF
V7L FM OSC
2.2PF 0.022uF 0.022uF
V7:IT
FM-RF IN RF GND AM LOW CUT MIX OUT AGC
C7 C19 C20
JC2 0
V3:AEP,CET,SP/ V7:AEP, CET,UK,SP,KR
AM RF IN FM RF OUT RF VCC
V3:AR/ V7:CND,AR AUS,TW,E4
ANT1 FM TELESCOPIC ANTENNA
Q2 KRA302-RTK SWITCH
V7L
CFD-V3/V7/V7L Ver 1.4 2003.06 6-11. SCHEMATIC DIAGRAMS – MAIN SECTION (2/3) – ( Last digit : -12)
S355 MEGA BASS ON
C124 4700p
R124 6.8k
z
Refer to page 30 for Notes.
C224 4700p
OFF
R224 6.8k C223 0.47 50V R223 1k
C123 0.47 50V R123 1k
CNP305 12P
Refer to page 33 for IC Block Diagram.
RV352 VOLUME RV352(2/2) 20kB
5
1
5
1
IC304 BA5417
KH307 5P POWER AMP KH306 5P
AM LW
V3/V7 FM V7L
R251 4.7k
CD
JC310 0
Q101 KRC410-RTK
Q201 KRC410-RTK
R253 470
R153 470
TAPE CD RADIO OFF
V7L
4
C351 47 10V
CNP303 4P
+ -
C153 47 10V
C152 1000p
S351-1 FUNCTION
JC306 0
C253 47 10V
R151 4.7k
C252 1000p
TU_IN_L TU_IN_R CD_IN_L CD_IN_R L_OUT R_OUT CD TAPE 6V GND SYNC-R ISS1
RV352(1/2) 20kB
z
+ 1
C254 470 10V
C154 470 10V
R254 100 J301
C317 22 25V
C314 47 10V
D305 KDS120-RTK
Q312 KRC405 RTK
D308 KTZ 3.9-RTK R350 2.2k
C347 220 10V
KH902 4P 1
C349 10000p
4
Q401 KTA1266-GR INITIAL SWITCH
R386 3.3k
R417 10k R418 10k
R416 4.7k C402 10 50V
C343 0.01
IT R343 1k
D310 L-34HD
Q402 KRC402
OPR/BATT
R344 220 C341 3300 16V
VOLTAGE DETECT VCC CONT N.C. TC N.C. VM GND VOUT
R402 10k
JC302 0 R403 22k
Q409 KTC3203Y-AT MOTOR SWITCH
P.GND R-OUT L-OUT UCOM-GND TU-GND TU +B D.GND CD 6V CD 3.3V AU MUTE
4
S601 (MD POWER)
24
R404 1k
R401 100k
D306 1SS355TE-17
R415 3.3k
JC303 0
Q402,405 POWER SWITCH
Q311,312 +B SWITCH
24
IC401 MM1468XD
R341 3.3k R340 3.3k
EXCEPT IT
R352 680 R353 680 R354 680
R351 680
C345 0.01
R345 1k
R360 100k
C346 0.01
C348 100 10V
JC401 0
D311 KDZ 7.5-RTK
EXCEPT IT
R348 1k
C271 10 50V
CD
Q405 KTA1266-GR-AT
Q310 KTC3203Y-AT +3.3V REG
R349 330
S351-2 FUNCTION AM V3/V7 FM LW V7L
R154 100
C255 0.1
C320 0.022
R314 4.7k Q311 KTB1241Y-AT
C171 10 50V
C155 0.1
R342 3.3k
R319 4.7k
TAPE CD RADIO OFF Q309 2SD2396K +6.9V REG
R346 1k
R315 1k
C156 47 10V
D301 1SS355TE-17
JC305 0
D302 1SS355TE-17
D314 1SS355TE-17
D304 1SS355TE-17
D303 1SS355TE-17
D309 1SS355TE-17
ISS1 TU.L TU.GND TU.R FM TU +B S-GND
C256 47 10V
Q101,201 MUTE
C316 1 50V
1 CNP304 4P
M601 CAPSTAN/REEL MOTOR
C401 100 10V
GND 9V AC 4.5V
SP201 SPEAKER (R-CH) SP101 SPEAKER (L-CH)
CFD-V3/V7/V7L
Ver 1.4 2003.06
6-12. SCHEMATIC DIAGRAMS – MAIN SECTION (3/3) – ( Last digit : -12)
z
Refer to page 30 for Notes.
z
Refer to page 13 for Explanation of IC Terminals.
R811 10k CN802 15P
P.GND
R809 1k
C810 100p
1
R810
100
R812
1k
R813
1k
FF
R814
1k
FR
R815
100
PLAY/PAUSE
R816
100
PLAY MODE
16
CD6V FSEQ DRF DO
5
*WRQ CL
10
CE DI *RES
10
ENTER GND COM0 COM1
U-RESET
V3: AR/V7:CND,AR,AUS,E4,IT,TW/V7L V3: AEP,CET,SP/V7:AEP,CET,KR,SP,UK
15
R805 220k
C802 47 10V
C801 *
S23
ENTER
PLAY
MODE
FF
FR
STOP
WRQ
S0
NC
S21
S1
NC
S20
S2
NC
S19
S3
IC801
S18
XT1
S17
XT2
S16
VDD
S15
VSS
R851 4.7k
5 S22
S14
DIGITAL SIGNAL PROCESSOR LCD DRIVER SYSTEM CONTROL
CL1
C851 22p
CL2 RESET
S13 S12 S11
NC
R806 220 C841 0.1
UCOM-GND
Q801 KRC404-RTK RESET
TU-GND TU +B R-OUT
C842 0.1
L-OUT D.GND
C843 0.1
CD 3.3V P.GND
C844 0.1
CD 6V AU MUTE
1
2
C891 1000p
KH801 2P
25
25
S6
S5
S4
S3
S2
S1
S0
COM3
COM2
COM1
COM0
VLC2
S7
VLC1
S8
C-RST
VLC0
S9
CE
CAPL
SYNC-R
R819 100
C805 0.1
S10
CAPH
R818 100
COM2 COM3
NC
IC
R801 22
DOOR
DO
TEST
0.1 0.01
FSEQ
* C801
MUTE
D.GND CD3.3V
DRF
L-CH
DIN
CLK
R-CH
S801 CD DOOR (OPEN/CLOSE)
STOP
1 CN801 16P
S4
CFD-V3/V7/V7L Ver 1.4 2003.06
6-13. PRINTED WIRING BOARDS – CONTROL/POWER SECTION – (Exsept V7: E4 model) 2
1
JC309
6
7
8
9
IC301
C304 R307 C310 C307 V7L
S301 R305
C202
R315 R314
C205
R206
C102
CONTROL BOARD
-1-2
R306
S301 PB r REC
S402 L
CN401
R424 R423 R422 R421
S401 s
BATT(R) BOARD
IC301
B-3
Q301 Q303
C-3 C-2
NEW TYPE 11 12 (11) (12)
1-680-677-
BATT(L) BOARD
F-7 E-7 F-6 E-6
S406 ENTER
12 (12)
FORMER TYPE
MAIN BOARD CN801 (Last digit :-11)
INLET BOARD
B
CNJ901 -AC IN
MAIN BOARD CN801 (Last digit :-12)
C902
T901 POWER TRANSFORMER
POWER BOARD
1-680-681-
11 12 NEW (11) (12) TYPE
1-680-680-
NEW 11 12 TYPE (12) (11)
C905
V3/V7
D901
KH901
C901
CNP908
FORMER TYPE
C903
F
D903
F901
D902
D904
DRY BATTERY SIZE "D" (IEC DESIGNATION R20) 6PCS, 9V
C904
D
KH904
CNP907 FORMER TYPE
R901
FORMER TYPE
CNP902
C
1-680-682-
NEW 11 12 TYPE (11) (12)
1-680-683-
NEW TYPE 11 12 (11) (12) FORMER TYPE
C
MAIN BOARD MAIN BOARD KH902 KH902 (Last digit :-11) (Last digit :-12) Note: • X : parts extracted from the component side. • : Pattern from the side which enables seeing.
26
26
Location
D901 D902 D903 D904
S403 l
S404 7
C306 R308 C305
Q301 T301 1-681-594-
S405 PLAY MODE
B
E
Semiconductor Location
LCD401 LIQUID CRYSTAL DISPLAY
R104 C103 R103 R102 R110 C101 C104 C107 R101 R210
C302
C201 R204 C203 R203 R202 C204 C207
D
R310 JC304 JC303
R302
JC301 R205 R211
R303
V7L
R301
R106 R201
CN303
HP901 ERASE HEAD
D
R111
C106 C206
Q302
C
C301
C105
R309 R304
MAIN BOARD CNP305 (Last digit :-12)
5
Ref. No.
C303
R-CH
MAIN BOARD CNP305 (Last digit :-11)
4
PRE BOARD
L-CH
B
Refer to page 14 for Circuit Boards Location.
z
R105 JC302
A
HRP901 RECORD/PLAY BACK HEAD
3
z
CFD-V3/V7/V7L
Ver 1.4 2003.06
6-14. PRINTED WIRING BOARDS – CONTROL/POWER SECTION – (V7: E4 model) 1
IC301
C304 R307
7
CONTROL BOARD
-1-2
S301
R305
C202
C201 R204 C203 R203 R202 C204 C207
JC301 R205 R211
JC304
R206
C205
CN303
R302
C302
C102
R315 R314
R301
C105
R111
C106 C206 R303
MAIN BOARD CNP305
6
8
9
LCD401 LIQUID CRYSTAL DISPLAY
R104 C103 R103 R102 R110 C101 C104 C107 R101 R210
C301
R105 JC302
R309 R304
D
5
Semiconductor Location Ref. No.
C303
R-CH
B
4
PRE BOARD
L-CH
HP901 ERASE HEAD
Refer to page 14 for Circuit Boards Location.
z
R106 R201
HRP901 RECORD/PLAY BACK HEAD
3
JC303
A
2
z
R306
S402 L
S404 7
S405 PLAY MODE
F-7 E-7 F-6 E-6
IC301
B-3
Q301 Q303
C-3 C-2
S403 l CN401
R424 R423 R422 R421
S401 s
C306 R308 C305
C307 Q301 T301 1-681-594C
S301 PB r REC
S406 ENTER
12 (12)
12 (12)
1-680-677-
B BATT(R) BOARD
BATT(L) BOARD
MAIN BOARD CN801
INLET BOARD CNJ901 -AC IN
VOL SEL BOARD S901 VOLTAGE SELECTOR 220-240V AC R 110-120V AC
RED BRN
D
WHT
11 (11)
C902
CNP908 1-680-681-
12 (12)
1-680-680-
12 (12)
C905
D901
KH901
WHT
C901
C903
D903 F
POWER BOARD
D902
T901 POWER TRANSFORMER
F901
E
D904
DRY BATTERY SIZE "D" (IEC DESIGNATION R20) 6PCS, 9V
C904
F902
1-682-707-
BRN
KH904
RED
CNP907
1-682-705-
11 (11)
R901 CNP902
1-682-706-
11 (11)
C MAIN BOARD KH902 Note: • X : parts extracted from the component side. • : Pattern from the side which enables seeing.
27
27
Location
D901 D902 D903 D904
CFD-V3/V7/V7L Ver 1.4 2003.06 6-15. SCHEMATIC DIAGRAMS – CONTROL/POWER SECTION –
z
Refer to page 30 for Notes.
z
Refer to page 30 for Waveforms.
z
Refer to page 31 for IC Block Diagram.
C301 100 10V CD CONTROL S401 C102 47 10V
R301 R103 1M 68k
R102 68
S402 IC301 TA2068N
REC/PB PRE AMP
C104 0.0022 C101 1000p
C103 0.047
R104 2.2k
C107 470p
HRP901 RECORD/PLAYBACK HEAD
R110 100
C105 47p
R101 15k
R210 100
L.LIN
L.PO
MIC I/EX
L.NF
L.RAD
C205 47p C203 0.047
R204 2.2k
C201 1000p
VCC
GND
R.LO
JC303 0
(-12)
R303 4.7k
C206 1 50V
LINE
R.RO
R.RAD
R.NF
TAPE
R.PO
R.LIN
R302 4.7k
C106 1 50V
R421 R422 R423 R424
4.7k 4.7k 4.7k 4.7k
S403 S404 S405 PLAY MODE
10
5
1
CN401 16P
LCD401 LIQUID CRYSTAL DISPLAY
R211 4.7k
CNP301
C204 0.0022
MIC
R206 2.2k
R203 68k
TU_IN_L TU_IN_R CD_IN_L CD_IN_R L_OUT R_OUT CD TAPE 6V GND SYNC-R ISS1
R105 15k
R106 2.2k
C202 R202 68 47 10V
R309 47
-2 JC304 0 R305 470
T301 BIAS COIL C305 470 R308 22k
16
R205 JC301 15k 0
REC
-1
R304 1k
JC302 0
V7:E4
MIC.NF
S301 PB
R111 4.7k
REC
REF
R.IN
R201 15k C207 470p
(-11)
EXCEPT L.IN V7:E4 L.LO
C302 100 10V
HE901 ERASE HEAD
AGC
L.RO
L R
STOP FF FR PLAY/PAUSE PLAY MODE ENTER GND COM0 COM1 COM2 COM3 S0 S1 S2 S3 S4
R314 470
R306 6.8k
C303 100 10V
R315 470 C310 220p
Q301 2SC2412-T-146 BIAS OSC
C306 0.01 C307 0.0022
C304 47 10V
(-12)
V7L
Q302 KRC402-RTK ISS1
R310 1M
R307 10
(-11)
JC309 0 V7L
E4
T901 POWER TRANSFORMER
VOL SEL BOARD
F902 T315mA/250V
S901 VOLTAGE SELECTOR 220-240V AC R 110-120V AC
EXCEPT E4
D902 1N4002B KH904 2P
V7L
KH901 2P
C902 0.022
F901 * *F901 3.15A/250V T2.5AL/250V T2.0AL/250V
CND,TW EXCEPT CND,TW,E4 E4
V7L C904 0.022
D901 1N4002B
C901 0.022 CNJ901
V3/V7
AC IN
C905 0.022 D904 1N4002B D903 1N4002B
C903 0.022 DRY BATTERY SIZE "D" (IEC DESIGNATION R20) 6PCS,9V
CNP902 4P (-11)
GND 9V AC 4.5V
1 1
CNP907 3P
1
R901 2.2k 3
4
4 (-12)
28
28
CNP908
S406 ENTER
CFD-V3/V7/V7L
Ver 1.4 2003.06
6-16. SCHEMATIC DIAGRAMS – CD SECTION –
z
Refer to page 30 for Notes.
Refer to page 30 for Waveforms.
z
z
Refer to page 32, 33 for IC Block Diagram.
R724 47k R728 10k R727 2.2k
R730 1k C746 100
C747 100 10V
C744 0.1
C745 0.1
R729 220
R707 10
Q701 KTN2907AS-RTK LASER POWER CONTROL
R712 100 5
C734 4700p
FE
C736 4700p
TE
JC703
0
C733 100 10V
C706 1 50V
TRACKING COIL
LRSY ASDFIN ASDACK ASLRCK 16MOUT EFLG C2F XVSS FSX/16MIN XIN XOUT XVDD RVDD RCHO RVSS LVSS LCHO LVDD
IC701 LC78645NE
CD RF/ SYSTEM SERVO PROCESSOR
C751 0.1
C750 100 10V
C707 1
C722 22p
C727 1000p
C723 0.01
FY
SLX
FX SPY SPX NC GND
OPOUT OPIN
F-
F+ T+
FIN (TIN)
T-
VCC
(FIN) TIN
VCC MUTE
GND
VREF REGO
SLIN RST
REG-B (SLIN)
SL-
SL+ SPIN
GND
IC702 BA6998FP-E2
SP+
R723 100
X701 33.86MHz C717 0.01
JC704 220 FB701 O
R715 150
C716 0.01
R714 150
C711 0.01
FB702
C735 1000 6.3V
C709 0.1
TX TY
C742 0.1
M702 SLED MOTOR
R741 6.8k M701 SPINDLE MOTOR
C720 22p
L706 0 C708 100p
SLY
FOCUS COIL
SPINDLE/SLED MOTOR DRIVE, TRACKING/FOCUS COIL DRIVE
C721 22p
LDD LDS FR VVDD PCKIST VVSS PDO2 PDO1 CONT1 CONT2 CONT3 VSS VDD5 DRF *RES *WRQ DO DI CL CE
C705 4700p C743 0.1
VC C732 100 10V
1
C725 1000p
DATA DATACK
SLCO SLCIST EFMIN RF RFVDD RFVSS FIN1 FIN2 TIN1 TIN2 VREF REFI FE TEC TE RFMON JITTC ADAVDD ADAVSS TDO
FDO SPDO SLDO GPDAC CONT4 CONT5 SBCK/CONT6 SBCK/FG DEFECT V/*P FSEQ MONI1 MINI2 MONI3 MONI4 MONI5 (3.3V)VSS VDD DOUT TEST
LD
RF R711 330
C704 22p
47k 15k 15k 15k 15k 47k
SP-
PD
R708 10k
16
10
C724 22p
R710 4.7k
R709 22k C703 0.1
R701 R702 R703 R704 R705 R706
C726 1000p
1k 1k 1k 1k
C731 0.047
CNP701 16P VREF VCC E D A B C F GND LD VR PD F+ T+ TF-
R717 R716 R718 R721
R726 680 R725 680
C702 47 10V
C701 1000p
VREF VCC E D A B C F
R722 100 R719 100 R720 100
C729 1 C728 0.047
S701 (LIMIT)
CNP702 15P P.GND CD6V FSEQ DRF DO *WRQ CL CE DI *RES R-OUT L-OUT D.GND CD3.3V(D) RESET
R731 2.2k
C730 0.1
JC702 0 R743 6.8k JC701 0
R744 100k
C741 0.1
C740 470 10V
29
29
C754 0.01
C755 0.01
(-11)
(-12)
CFD-V3/V7/V7L Ver 1.4 2003.06 6-17. PRINTED WIRING BOARD – CD SECTION –
z
Refer to page 14 for Circuit Boards Location.
2
1
3
• Waveforms
4
OPTICAL PICK-UP BLOCK KSS-213C
CD BOARD A
Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. f • : internal component.
JC702 JC701
R744 JW718 JW721
JW715 15
5
16 Q701
R726 R724 C730 JW724 C726 R731
C744 C746
IC701 C745
C742
C723
C724 C725
C703
R719 R717 R718
R723
C716 C709 C711
C722
L706
JW707
R716 X701
JW730 FB701 JC704
A
MAIN BOARD CN802 (Last digit:-11)
A
MAIN BOARD CN802 (Last digit:-12)
C755
C754
C735
JW705
JW701
JW702
JW703 C727
CNP702
JW728
JW729
R729 C747
JW727
R725
C729
JW725
JW726
M702 SLED MOTOR
C728
C721
C734
R704 JC703 C736 C708
JW708 JW706
C707
JW709
TP (RF)
R730
C731
C743
C705
R708
R710 R711
R706 R701 R705 R703 R702
D
C704
JW711
C
C732
C702
R721 C720 R720
C751
JW713
JW710 R709
M
C701 JW712
C706
R707
R743
10 R712 JW714
C750
C740
JW722
2
C717
CNP701
JW720
R722
1 C733
JW719
C741
S701 (LIMIT)
R727 R728 JW723
B
Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
IC702
JW716
M
JW717
R741
M701 SPINDLE MOTOR
NEW TYPE
R714 R715
1-680-943-
E
• A : B+ Line. • H : adjustment for repair. • Power voltage is dc 9 V and fed with regulated dc power supply from battery terminal. • Voltage and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM (RADIO SECTION), TAPE PLAY (TAPE SECTION) ( ) : AM (RADIO SECTION), REC (TAPE SECTION) • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. • Circled numbers refer to waveforms. • Signal path. F : FM f : AM E : PB a : REC J : CD • Abbreviation CND : Canadian IT : Italian CET : East European & Russian SP : Singapore AR : Argentina AUS : Australian TW : Taiwan KR : Korean E4 : 110-120V AC/220-240V AC Changeable
Location
IC701 IC702
D-2 A-3
Q701
B-2
3.1Vp-p
17.95 µsec
VOLT/DIV : 1 V AC TIME/DIV : 5 µsec
Q301 C
2 30Vp-p
17.95 µsec
VOLT/DIV : 1 V AC (ATT : 1/10) TIME/DIV : 5 µsec
T301
– CD SECTION –
3
1
(PLAY MODE)
0.7–1.0Vp-p (LPC ON)
IC701 4 RF
VOLT/DIV : 0.5 V AC TIME/DIV : 0.5 µsec
0.6Vp-p
IC701 qd (FE)
4
2
VOLT/DIV : 1 V AC TIME/DIV : 1 msec
(PLAY MODE)
1.1Vp-p
0.6Vp-p
IC701 rk XOUT
Semiconductor Location Ref. No.
1
29.53nsec
12 13 (12) (13) FORMER TYPE
z
Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
– CONTROL/POWER SECTION –
Note: • X : parts extracted from the component side. • : Pattern from the side which enables seeing. f • : internal component.
30
30
VOLT/DIV : 0.5 V AC TIME/DIV : 0.2 µsec
IC701 qg (TE)
VOLT/DIV : 20 V AC TIME/DIV :1 msec
CFD-V3/V7/V7L • IC BLOCK DIAGRAMS –MAIN SECTION–
AM RF IN
FM RF OUT
RF VCC
FM OSC
AM OSC
AFC
DET OUT
MPX IN
LPF2
LPF1
L-OUT
R-OUT
IC1 TA2111N
24
23
22
21
20
19
18
17
16
15
14
13
AM RF AMP
FM OSC
AM OSC
AF AMP
DECODER VCO DIVIDER
AF BUFFER
FM MUTE
8
9
TUN LED
ST LED
10
11
12 QUAD
7 AM IF IN
FM IF AMP
ST LED
6
AM IF AMP
TUN LED
5
VCC
RF GND
4
AGC
FM RF IN
3
FM/AM MIX OUT
2
AM LOW-CUT
1
AGC
FM DET
GND
FM MIX
FM RF AMP
LEVEL DET
AM DET
FM IF IN
AM MIX
ST/MONO FM/AM
• IC BLOCK DIAGRAMS –CONTROL/POWER SECTION–
17
16
15
14
13
1k
1k
10k
MIC IN
18
R. LIN
19
TAPE
20
R. RAD
21
LINE
REC
22
R. LO
L. RAD
23
VCC
MIC I/EX
24
L. LO
L. LIN
IC301 TA2068N
10k LOGIC 1k
10k
10k
MONITOR AMP
ON
ON
MUTE
––––– TAPE
MUTE
LINE
10k
10k BUF AMP B2
BUF AMP B1 TAPE
10k
7dB
MONITOR AMP
LINE
6k
RADIO
RADOI
7dB
––––– TAPE
6k
15k
10k
TAPE
10k
BUF AMP
BUF AMP
A2
A1 10k
10k
10k
NAB AMP1
ON
ALC2
ALC1 26dB
NAB AMP2
26dB REC AMP1
MIC AMP1
MUTE
10k
REC AMP2
DET
1k 10k
2.1
2
3
4
5
6
7
8
9
10
11
L. NF
L. RO
L. IN
REF
GND
R. IN
R. RO
R. NF
R. PO
12 MIC NF
1
L. PO
AMP
AGC
REF
31
CFD-V3/V7/V7L
• IC BLOCK DIAGRAMS –CD SECTION–
CONT2 CONT3
VSS VDD5V
DRF
*RES
*WRQ DO DI CL CE
78 77 76 75 74 73
72 71 70
69 68
67
66
65 64 63 62 61
APC
PLL VCEC
GATE
SERIAL OUT
60 DATA 59 DATACK 58 LRSY
EXTERNAL AUDIO IN
57 ASDFIN 56 ASDACK 55 ASLRCK
SLICE LEVEL CONTROL
54 16MOUT RAM
RF RFVDD RFVSS
4 5 6
–
FIN1
7
+
FIN2
8
MIX
EQ
ERROR CORRECTION AUDIO CD C1-1, C2-2
AGC
+
–
–
+
+
AUTO ADJUST PH
LPF
LEVEL SET
TIN1
DRF
COMMAND INTERFACE
ATTENUATION DEEMPHASIS
GENERALPURPOSE PORTS
PCK
SLCO 1 SLCIST 2 EFMIN 3
GATE INTERPOLATION MUTE
CONT1
FR
80 79
PD02 PD01
LDD LDS
VVDD PCKIST VVSS
IC701 LC78645E
+
+
TBAL
–
46 RVSS 45 RCHO 44 RVSS
+ +
TBAL LPF
+
LPF
43 LVSS 42 LCHO 41 LVSS
–
VREF 11
– +
REFI 12
FRAME SYNC DETECT, PROTECT INSERT, EFM DECODE
+
LPF
– +
FE 13 TEC 14 TE 15 RFMON 16
JITTC 17
RUPTURE DEFECT
–
SW
TRACK JUMP
JITTER DETECT
A/D
AUDIO OUT
SERVO PROCESSOR RAM
S/H
TEST
FSEQ
DOUT
32 33 34 35 36 37 38 39 40 MONI2 MONI3 MONI4 MONI5 (3.3V)VSS VDD
31
V/*P
SBCK/CONT6
CONT5
CONT4
SPDO SLDO GPDAC
FDO
28 29 30
MONI1
20 21 22 23 24 25 26 27
32
MONITOR SIGNAL SELECTOR
CLV, CAV CONTROL
D/A
SBCK/FG DEFECT
TDO
SUBCODE DECODE CRC
MONI CONT
SW
ADAVDD 18 ADAVSS 19
49 XIN 48 XOUT 47 XVDD
CLOCK GENERATOR
1BIT DAC
–
TIN2 10
51 XVSS 50 FSX/16MIN
BH
–
9
8FS DIGITAL FILTER
53 EFLG 52 C2F
CFD-V3/V7/V7L
VCC
NC
SLIN
SL +
24
23
22
21
20
19
18
VCC
VCC
16
15
LEVEL SHIFT – +
– + + –
REGULATOR VOLTAGE DETECT, BIAS VOLTAGE DETECT, THERMAL SHUT DOWN
LEVEL SHIFT
DRIVER MUTING
+ –
+ –
LEVEL SHIFT
– +
DRIVE BUFFER 9 10
11
12
13 14
SP +
GND SPOUT
REGOUT
8
SP –
F+
7
SPIN NC
6
GND
3 4 5
MUTE
2
FIN RESET REG-B
DRIVE BUFFER F–
17 DRIVE BUFFER
LEVEL SHIFT
1
SPI
VCC
25
VREF
VREFI
26 DRIVE BUFFER
SL –
NC
27
TIN
T+
28
T–
GND
IC702 BA6998FP
• IC BLOCK DIAGRAMS –MAIN SECTION–
IC401 MM1468XD
CONT
1
NC
2
VM
3
GND
4
8 VCC
VCC
VH DET
LATCH
7 TC
6 NC VL DET
5 VOUT
33
CFD-V3/V7/V7L Ver 1.5
SECTION 7 EXPLODED VIEWS
NOTE : • -XX, -X mean standardized parts, so they may have some difference from the original one. • Color indication of Appearance Parts Example : KNOB, BALANCE (WHITE)• • • (RED) ↑ ↑ Parts color Cabinet's color
• Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. • Abbreviation CND : Canadian IT : Italian CET : East European & Russian SP : Singapore AR : Argentina AUS : Australian TW : Taiwan KR : Korea E4 : AC 110-120V AC/ 220-240V AC Changeable
• Items marked “ * ”are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
#2 #2
7-1. FRONT CABINET SECTION #1
#2
SP101
#1
9
#2
9 #2
8 10
6 9
11 9 #1
4 9 2
7
SP201
9
1
#1
5
3 Ref. No. 1 1 1 1 1 1 1 2 2
2
Part No. 3-226-979-01 3-226-979-11 3-226-979-21 3-229-933-01 3-229-933-11
Description Remark WINDOW (TU) (V7:CND,AUS,TW(SILVER)) WINDOW (TU) (V7:AUS,AR,E4,TW(BLUE)) WINDOW (TU) (V3:AR) WINDOW (TU) (V7:AEP,CET,UK,SP,KR) WINDOW (TU) (V7:IT)
3-229-949-01 3-231-903-01 3-031-549-21 3-031-549-31
WINDOW (TU) (V3:AEP,CET,SP) WINDOW (TU LW) (V7L) KNOB (VOL) (V7:CND,AUS,TW(SILVER)) KNOB (VOL) (V7:AEP,IT,CET,UK,AUS,AR,SP,E4,KR, TW(BLUE)/V7L) 3-229-950-01 KNOB (VOLUME) (V3)
Ref. No. 5
5 6
6 6 6 7
* 8 3
3 4 4
3-033-527-01 BUTTON CD (PLAY/STOP)...(SILVER) (V7:CND,AUS,TW) 3-226-986-01 BUTTON CD (PLAY/STOP)...(BLUE) (V7:AEP,IT,CET,UK,AUS,AR,SP,E4,KR,TW/V7L) 3-229-951-01 BUTTON CD (PLAY/STOP) (V3) X-3380-207-1 PANEL SUB ASSY (V7) X-3380-519-1 PANEL SUB ASSY (V3)
4 5
X-3380-521-1 PANEL SUB ASSY (V7L) 3-033-528-01 BUTTON CD (AMS) (V7:CND,AUS,TW(SILVER))
3
34
Part No. Description Remark 3-226-987-01 BUTTON CD (AMS) (V7:AEP,IT,CET,UK,AUS,AR,SP,E4,KR, TW(BLUE)/V7L) 3-229-952-01 BUTTON CD (AMS) (V3) X-3380-206-1 CABINET (FRONT) SUB ASSY...(SILVER) (V7:CND,AUS,TW) X-3380-518-1 CABINET (FRONT) SUB ASSY...(SILVER) (V7:AEP,IT,CET,UK,AR,SP,E4,KR/V7L) X-3380-520-1 CABINET (FRONT) SUB ASSY (V3) X-3380-796-1 CABINET (FRONT) SUB ASSY...(BLUE) (V7:AEP,IT,CET,UK,AUS,TW/V7L) 3-031-558-01 SHAFT (TU) 1-681-677-12 CONTROL BOARD
9 10 11 11 SP101
4-951-620-01 3-031-551-01 3-031-552-41 3-229-954-01 1-529-723-11
SCREW (2.6X8), +BVTP POINTER KNOB (TU) (V7/V7L) KNOB (TUNE) (V3) SPEAKER (10cm) (L-CH) (V3)
SP101 SP201 SP201
1-529-723-21 SPEAKER (10cm) (L-CH) (V7/V7L) 1-529-723-11 SPEAKER (10cm) (R-CH) (V3) 1-529-723-21 SPEAKER (10cm) (R-CH) (V7/V7L)
CFD-V3/V7/V7L Ver 1.5 7-2. REAR CABINET SECTION
57
58
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
#2 #2 #1
59 70
60
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
70
56
61 62 55 63 54
67 66 65
65 64
T901
66 68
#1 #1
53
#1
52
#1
Ref. No. 51 51 51 51 51
Part No. 3-226-989-01 3-226-989-11 3-229-939-11 3-229-939-21 3-229-939-31
51 51 51 51
3-229-939-41 3-229-940-11 3-229-940-21 3-229-940-31
51 51 51 * 52 * 52 * 53
51 69
Description Remark CABINET (REAR)...(SILVER) (V7:CND,TW) CABINET (REAR)...(SILVER) (V7:AUS) CABINET (REAR)...(SILVER) (V7L) CABINET (REAR)...(SILVER) (V7:IT) CABINET (REAR)...(SILVER) (V7:AEP,UK,CET,AR,SP,KR)
CABINET (REAR)...(SILVER)(V7:E4) CABINET (REAR)...(BLUE) (V7L) CABINET (REAR)...(BLUE) (V7:IT) CABINET (REAR)...(BLUE) (V7:AEP,UK,CET,AR,SP) 3-229-940-41 CABINET (REAR)...(BLUE) (V7:AUS) 3-229-958-01 3-229-958-11 1-680-682-12 1-682-706-11 1-680-683-12
CABINET (REAR) (V3:AEP,CET) CABINET (REAR) (V3:SP,AR) INLET BOARD (EXCEPT E4) INLET BOARD (E4) POWER BOARD
Ref. No. 58 58 58
59
Description Remark LID (CD) (V3) LID CD...(SILVER) (V7:CND,AUS,TW) LID CD...(SILVER) (V7:AEP,IT,CET,UK,AR,SP,E4,KR/V7L) 3-229-946-01 LID CD ... (BLUE) (V7:AEP,IT,CET,UK,AUS,TW/V7L) 1-452-899-11 MAGNET
60 61 62 63 63
3-019-395-01 3-031-562-01 4-951-620-11 3-031-540-11 3-031-540-81
63 63
3-226-976-01 HANDLE...(SILVER) (V7:TW) 3-229-931-01 HANDLE...(SILVER) (V7:AEP,IT,CET,UK,AR,SP,E4,KR/V7L) 3-229-935-01 HANDLE...(BLUE)(V7:AEP,IT,CET,UK,AUS, TW/V7L) 1-680-680-12 BATT (L) BOARD 3-028-154-01 TERMINAL (–), BATT
58
63
* 64 54 54 55 55
55 56 57 57 57 57
3-031-570-41 KNOB (FUNCTION) (V7/V7L) 3-229-947-01 KNOB (FUNCTION) (V3) 3-226-978-01 BUTTON (MEGA BASS) (V7:CND,AUS,TW(SILVER)) 3-229-932-01 BUTTON (MEGA BASS) (V7:AEP,IT,CET,UK,AUS,AR,SP,E4,KR, TW(BLUE) /V7L) 3-229-948-01 BUTTON (MEGA BASS) (V3) 3-031-561-01 SPRING (CASSETTE) 3-043-830-01 HOLDER, CASSETE (V3) 3-226-991-01 HOLDER, CASSETE...(SILVER) (V7:CND,AUS,TW) 3-229-943-01 HOLDER, CASSETTE...(SILVER) (V7:AEP,IT,CET,UK,AR,SP,E4,KR/V7L) 3-229-944-01 HOLDER, CASSETTE...(BLUE) (V7:AEP,IT,CET,UK,AUS,TW/V7L)
65 66
* 67 68 68 68
68
Part No. 3-031-538-91 3-226-993-01 3-229-945-01
4-960-167-01 1-680-681-12 3-036-134-81 3-226-980-01 3-229-934-01
PLATE, CHUCKING SPRING (CD) SCREW (2.6X10), +BVTP HANDLE (V7:CND,AUS) HANDLE (V3)
SCREW (3X8) (DIA. 10), +WH BATT (R) BOARD LID, BATTERY CASE (V3) LID BATTERY...(SILVER) (V7:TW) LID BATTERY...(SILVER) (V7:AEP,IT,CET,UK,AR,SP,E4,KR/V7L)
68 69 70 0 T901
3-229-936-01 LID BATTERY...(BLUE) (V7:AEP,IT,CET,UK,AUS,TW/V7L) 3-926-244-71 LID BATTERY...(SILVER) (V7:CND,AUS) 3-034-633-01 COVER (VOL SEL) 3-015-345-21 CUSHION 1-433-576-11 TRANSFORMER, POWER (CND,TW)
0 T901 0 T901
1-435-921-11 TRANSFORMER, POWER (EXCEPT CND,TW,E4) 1-435-922-11 TRANSFORMER, POWER (E4)
35
CFD-V3/V7/V7L Ver 1.5
ANT1
7-3. UPPER CABINET SECTION 115
117
#1
#5
#1
118
113 S801
120
116
105 107 109
122
104 106
#1
#1
126
#1
103 108
119
not supplied
#4
127 121
110 102
123
114 112
KSM-213CDP
127 111
121 121
101
123 121
124
#1
125 Ref. No.
Part No.
* 101 * 101 * 101
102
A-3062-295-A MAIN BOARD, COMPLETE (V7L) A-3062-411-A MAIN BOARD, COMPLETE (V7:IT) A-3062-472-A MAIN BOARD, COMPLETE (V3:AEP,CET,SP/V7:AEP,CET,UK,SP,KR) A-3347-106-A MAIN BOARD, COMPLETE (V3:AR/V7:CND,AR,AUS,TW,E4) 4-960-167-01 SCREW (3X8) (DIA. 10), +WH
103 104 104 105 105
3-031-560-01 3-031-541-51 3-031-541-61 3-031-542-51 3-031-542-61
SHAFT (MD) BUTTON (REC) (V7/V7L) BUTTON (REC) (V3) BUTTON (PLAY) (V7/V7L) BUTTON (PLAY) (V3)
106 106 107 107 108
3-031-543-51 3-031-543-61 3-031-544-51 3-031-544-61 3-031-545-51
BUTTON (REW) (V7/V7L) BUTTON (REW) (V3) BUTTON (FF) (V7/V7L) BUTTON (FF) (V3) BUTTON (STOP) (V7/V7L)
108 109 109 110 * 111
3-031-545-61 3-031-546-51 3-031-546-61 3-031-559-01 1-757-584-11
BUTTON (STOP) (V3) BUTTON (PAUSE) (V7/V7L) BUTTON (PAUSE) (V3) GEAR (PVC 2 BAND) CABLE FLEXIBLE FLAT 15P
* 112 * 112
1-757-688-11 CABLE FLEXIBLE FLAT 10P (V3/V7) 1-757-845-11 FFC 12P (V7L)
* 101
Description
Remark
Ref. No.
Part No.
* 113 * 114
1-680-679-12 VOLUME BOARD 1-757-583-11 CABLE FLEXIBLE FLAT 16P 3-922-112-41 DAMPER
115 116 117 117
36
#4
117 117
Description
3-922-112-21 DAMPER 3-226-990-01 CABINET (UPPER)...(SILVER) (V7:CND,AUS,TW) 3-229-941-01 CABINET (UPPER)...(SILVER) (V7:AEP,IT,CET,UK,AR,SP,E4,KR/V7L) 3-229-942-01 CABINET (UPPER)...(BLUE) (V7:AEP,IT,CET,UK,AUS,TW/V7L) 3-229-959-01 CABINET (UPPER) (V3)
118 119 * 120 121 122
3-225-866-01 4-951-620-01 1-680-678-12 3-921-725-11 3-226-992-01
CUSHION (MD BUTTON) SCREW (2.6X8), +BVTP FM SW BOARD SCREW (2.6X10), +PWH TERMINAL (ANTENNA)
123 124 * 125 126 127
3-038-948-01 1-757-689-11 A-3347-105-A 3-923-736-01 3-038-948-11
RUBBER, VIBRATION PROOF (PINK) CABLE FLEXIBLE FLAT 16P CD BOARD, COMPLETE COVER, CD RUBBER, VIBRATION PROOF (BLUE)
ANT1 S801
Remark
1-501-883-21 ANTENNA, TELESCOPIC 1-692-960-11 SWITCH, PUSH (1 KEY) (CD DOOR OPEN/CLOSE)
CFD-V3/V7/V7L Ver 1.2 2001.08
7-4. MECHANISM DECK SECTION (1) (MF-V5-117)
HRP901
159 170
HE901
158
160
161 162
169
168
163
157
164
171 156
165 167
172
155
174 154 #3
166
151 153 152 173
#3
Ref. No.
Part No.
Description
151 152 153 154 155
3-933-010-01 3-933-025-01 3-040-857-01 3-933-024-01 3-933-019-01
SPRING (S/P), TORSION SPRING (P), TORSION LEVER (P) ROLLER, PINCH SPRING (F/R), TORSION
156 157 158 159 * 160
3-933-028-01 3-933-016-01 3-008-590-01 3-008-592-01 3-008-588-01
SPRING (FWD), TORSION GEAR (S REEL) SLIDER (REC) BASE (H), HEAD SLIDER (REW)
* 161 * 162 * 163 164
3-008-589-13 3-008-587-01 3-008-591-01 3-933-004-01
SLIDER (FF) SLIDER (STOP) SLIDER (PAUSE) CLAW, REEL
Remark
Ref. No.
Part No.
* 165
3-933-021-01 SLIDER (FRP)
Description
Remark
* 166 167 168 169 * 170
3-933-006-01 3-934-833-01 3-022-794-02 3-933-007-01 3-012-114-01
SLIDER (EJECT) SPRING (FRP) SPRING (BT) PLATE, LOCK LEVER (FR)
171 172 * 173 * 173 174
3-222-727-01 4-951-620-01 A-3062-296-A A-3347-104-A 3-222-726-01
LEVER (REC) SCREW (2.6X8), +BVTP PRE BOARD, COMPLETE (V7L) PRE BOARD, COMPLETE (EXCEPT V7L) CHASSIS (TC)
HE901 1-543-876-11 HEAD (ERASE) HRP901 1-500-668-11 HEAD,MAGNETIC (RECORD/PLAYBACK)
37
CFD-V3/V7/V7L
7-5. MECHANISM DECK SECTION (2) (MF-V5-117)
207 206
219 209
208 205
204
210
216 203 211
S601
218
212
M601
213 217
214 215 202
Ref. No.
201
Part No.
Description
201 202 203 204 205
3-933-029-01 3-933-182-01 3-932-995-01 X-3371-667-1 3-932-997-01
LEVER, ERASING PREVENTION SPRING, CASSETTE GEAR (MID) CLUTCH ASSY GEAR (CAM)
* 206 207 208 209 210
3-932-999-01 3-932-998-01 3-009-648-01 3-936-438-01 X-3373-572-1
SLIDER (SW) SPRING (GROUND), TORSION LEVER (S.OFF) LEVER (K) REEL ASSY (N), T
211
38
3-933-020-01 BELT
#4
Remark
Ref. No.
Part No.
Description
Remark
212 213 214 215
X-3377-877-2 3-932-993-01 3-343-358-01 3-223-156-01
FLYWHEEL ASSY CHASSIS, OUTSERT RING, RETAINING SPRING (CAM), COMPRESSION
216 217 218 219 M601
3-939-383-02 3-937-760-01 3-934-336-01 3-009-650-02 A-3320-446-A
SPRING, COMPRESSION SPRING (GROUND), COMPRESSION BEARING SPRING (K), COMPRESSION MOTOR ASSY (CAPSTAN/REEL) (INCLUDING PULLEY)
S601
1-762-679-11 SWITCH, LEAF (MD POWER)
CFD-V3/V7/V7L
Ver 1.3 2002.06
7-6. CD BLOCK SECTION (KSM–213CDP)
253
254
256 not supplied
M701
251 255
252 (including M701) M702
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Ref. No. 251 252 0 253 254
Part No.
Description
Remark
2-626-908-01 SHAFT, SLED X-2162-709-1 CHASSIS ASSY (CDP), MOTOR (SPINDLE) (INCLUDING M701) 8-848-483-05 OPTICAL PICK-UP KSS-213C 2-624-188-02 GEAR (A)
Ref. No.
Part No.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Description
Remark
255
2-627-003-01 GEAR B (BP)
256 M702
3-713-786-51 SCREW +P 2X3 X-2625-769-1 GEAR ASSY (MB), MOTOR (SLED) (INCLUDING GEAR)
39
CFD-V3/V7/V7L Ver 1.5
BATT (L)
SECTION 8 ELECTRICAL PARTS LIST
BATT (R)
CD NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
Ref. No.
*
• SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . The components identified by mark 0 or dotted line with mark 0 • CAPACITORS are critical for safety. uF: µF Replace only with part number • COILS specified. uH: µH Les composants identifiés par une • Abbreviation marque 0 sont critiquens pour la CND : Canadian sécurité. IT : Italian Ne les remplacer que par une pièce CET : East European & Russian portant le numéro spécifié. SP : Singapore AR : Argentina When indicating parts by reference number, please include the board. AUS : Australian TW : Taiwan E4 : 110-120V AC/220-240V AC changeable KR : Korean • (-11) (-12) : Last digit
Part No. Description 1-680-680-12 BATT (L) BOARD
Remark
Ref. No. C732
Part No. Description 1-104-658-11 ELECT
100uF
20%
Remark 10V
C733 C734 C735 C736 C740
1-104-658-11 1-162-968-11 1-126-916-11 1-162-968-11 1-126-725-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT
100uF 0.0047uF 1000uF 0.0047uF 470uF
20% 10% 20% 10% 20%
10V 50V 6.3V 50V 10V
C741 C742 C743 C744 C745
1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
C746 C747 C750 C751 C754
1-126-925-11 1-126-925-11 1-126-925-11 1-164-156-11 1-162-970-11
ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP
100uF 100uF 100uF 0.1uF 0.01uF
20% 20% 20% 10%
10V 10V 10V 25V 25V
C755
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
5%
1/16W
************ 3-028-154-01 TERMINAL (–), BATT
* CNP908 1-815-550-11 PIN, CONNECTOR (PC BOARD) 2P ***************************************************** *
1-680-681-12 BATT (R) BOARD
************
25V 25V 25V 25V 25V
3-028-154-01 TERMINAL (–), BATT
***************************************************** *
A-3347-105-A CD BOARD, COMPLETE
***************** C701 C702 C703 C704 C705
1-162-964-11 1-104-657-11 1-107-826-11 1-162-919-11 1-162-968-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 47uF 0.1uF 22PF 0.0047uF
10% 20% 10% 5% 10%
50V 10V 16V 50V 50V
C706 C707 C708 C709 C711
1-126-960-11 1-115-156-11 1-162-927-11 1-164-156-11 1-162-974-11
ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
1uF 1uF 100PF 0.1uF 0.01uF
20%
50V 10V 50V 25V 50V
C716 C717 C720 C721 C722
1-162-974-11 1-163-021-11 1-162-919-11 1-162-919-11 1-162-919-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.01uF 0.01uF 22PF 22PF 22PF
C723 C724 C725 C726 C727
1-162-974-11 1-162-919-11 1-162-964-11 1-162-964-11 1-162-964-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
C728 C729 C730 C731
1-165-176-11 1-125-837-11 1-107-826-11 1-165-176-11
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
5%
10% 5% 5% 5%
50V 50V 50V 50V 50V
0.01uF 22PF 0.001uF 0.001uF 0.001uF
5% 10% 10% 10%
50V 50V 50V 50V 50V
0.047uF 1uF 0.1uF 0.047uF
10% 10% 10% 10%
16V 6.3V 16V 16V
* CNP701 1-779-553-21 CONNECTOR, FFC/FPC 16P CNP702 1-784-737-11 CONNECTOR, FFC 15P FB701
0uH
IC701 IC702
6-700-455-01 IC 8-759-591-62 IC
LC78645NE BA6998FP
JC701 JC702 JC703 JC704
1-216-864-11 1-216-864-11 1-216-864-11 1-216-813-11
SHORT SHORT SHORT METAL CHIP
0 0 0 220
L706
1-414-445-11 FERRITE BEAD
Q701
40
1-469-701-11 FERRITE BEAD
8-729-054-57 TRANSISTOR
KTN2907AS-RTK
CFD-V3/V7/V7L Ver 1.5
CD Ref. No.
Part No.
Description
Remark
Ref. No.
CONTROL
Part No.
FM SW
INLET
Description
Remark
R701 R702 R703 R704 R705
1-216-841-11 1-216-835-11 1-216-835-11 1-216-835-11 1-216-835-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 15K 15K 15K 15K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R706 R707 R708 R709 R710
1-216-841-11 1-216-797-11 1-216-833-11 1-216-837-11 1-216-829-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 10 10K 22K 4.7K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R711 R712 R714 R715 R716
1-216-815-11 1-216-809-11 1-216-811-11 1-216-811-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
330 100 150 150 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R717 R718 R719 R720 R721
1-216-821-11 1-216-821-11 1-216-809-11 1-216-809-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 1K 100 100 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R722 R723 R724 R725 R726
1-216-809-11 1-216-809-11 1-216-841-11 1-216-819-11 1-216-819-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100 100 47K 680 680
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R727 R728 R729 R730 R731
1-216-825-11 1-216-833-11 1-216-813-11 1-216-821-11 1-216-825-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
2.2K 10K 220 1K 2.2K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R741 R743 R744
1-216-831-11 METAL CHIP 1-216-831-11 METAL CHIP 1-216-845-11 METAL CHIP
6.8K 6.8K 100K
5% 5% 5%
1/16W 1/16W 1/16W
S401 S402 S403 S404 S405
1-771-550-31 1-762-875-21 1-762-875-21 1-771-550-31 1-762-875-21
SWITCH, KEYBOARD (s) SWITCH, KEYBOARD (L) SWITCH, KEYBOARD (l) SWITCH, KEYBOARD (7) SWITCH, KEYBOARD (PLAY MODE)
S406
1-762-875-21 SWITCH, KEYBOARD (ENTER)
************************************************************* *
1-680-678-12 FM SW BOARD
***********
* KH1
1-565-385-11 HOLDER, CABLE 4P
S1
1-786-114-11 FM (ST/MO) SW (V3/V7:FM MODE, MONO/STEREO, V7L:FM MODE/ISS, MONO, 1/STEREO 2)
****************************************************** * *
1-680-682-12 INLET BOARD (EXCEPT E4) 1-682-706-11 INLET BOARD (E4)
******************** 1-533-233-31 HOLDER, FUSE 1-162-995-11 1-162-995-11 1-162-995-11 1-162-995-11 1-162-995-11
1-762-812-11 SWITCH, LEAF (LIMIT)
50V 50(V7L) 50V 50(V7L) 50V (V3/V7)
1-795-173-11 VIBRATOR, CERAMIC (33.86MHz)
****************************************************** *
0.022uF 0.022uF 0.022uF 0.022uF 0.022uF
X701
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0 CNJ901 1-526-838-11 INLET, AC 2P (-AC IN) (V3/V7:AEP,IT,CET,UK,AR,AUS,SP,E4,KR/V7L) 0 CNJ901 1-540-009-11 INLET, AC (-AC IN)(CND)
S701
C901 C902 C903 C904 C905
* CNP902 1-815-552-11 PIN, CONNECTOR (PC BOARD) 4P * CNP907 1-815-444-11 PIN, CONNECTOR 3P
1-680-677-12 CONTROL BOARD
************* D901 D902 D903 D904
* CN401
1-784-738-11 CONNECTOR, FFC 16P
0 F901 0 F901
1-216-829-11 1-216-829-11 1-216-829-11 1-216-829-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
4.7K 4.7K 4.7K 4.7K
DIODE DIODE DIODE DIODE
1N4002B 1N4002B 1N4002B 1N4002B
LCD401 1-804-219-11 DISPLAY PANEL, LIQUID CRYSTAL
R421 R422 R423 R424
8-719-063-79 8-719-063-79 8-719-063-79 8-719-063-79
5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W
0 F901 0 F902
1-533-468-11 FUSE, GLASS TUBE (DIA. 5) (TIME LAG 2.0AL/250V) (E4) 1-533-469-11 FUSE, GLASS TUBE (DIA. 5) (TIME LAG 2.5AL/250V) (V3/V7:AEP,IT,CET,UK,AR,AUS,SP,KR/V7L) 1-533-470-11 FUSE, GLASS TUBE (DIA. 5)(3.15A/250V) (V7:CND,TW) 1-533-460-11 FUSE, GLASS TUBE (DIA. 5)(315mA/250V)(E4)
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
41
CFD-V3/V7/V7L Ver 1.5
INLET Ref. No.
MAIN
Part No.
Description
Remark
* KH901 R901
1-573-287-11 HOLDER, CABLE 2P 1-216-825-11 METAL CHIP
2.2K
5%
1/16W
************************************************************* A-3062-295-A MAIN BOARD, COMPLETE (V7L) * * A-3062-411-A MAIN BOARD, COMPLETE (V7:IT) * A-3062-472-A MAIN BOARD, COMPLETE (V3:AEP,CET,SP/V7:AEP,CET,UK,SP,KR) A-3347-106-A MAIN BOARD, COMPLETE (V3:AR/V7:CND,AR,AUS,TW,E4)
*
********************* 3-031-559-01 7-621-775-20 7-685-675-19 7-685-645-79
GEAR (PVC 2 BAND) SCREW +B 2.6X5 SCREW +BVTP 5X20 TYPE2 N-S (V3/V7) SCREW +BVTP 3X6 TYPE2 N-S (V7L)
C1 C2 C3 C4 C5
1-162-964-11 1-162-915-11 1-162-974-11 1-104-662-11 1-162-915-11
C6 C7
1-162-910-11 CERAMIC CHIP 1-162-191-31 CERAMIC
C7 C8 C9 C10
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
0.001uF 10PF 0.01uF 22uF 10PF
10% 0.5PF 20% 0.5PF
50V 50V 50V 25V 50V
5PF 0.25PF 50V 2.2PF 10% 50V (V3:AR/V7:CND,AR,AUS,TW,E4) 1-162-195-31 CERAMIC 4.7PF 10% 50V (V3:AEP,CET,SP/V7:AEP,CET,UK,SP,IT,KR) 1-126-963-11 ELECT 4.7uF 20% 50V 1-126-963-11 ELECT 4.7uF 20% 50V
C11 C12 C13 C14
1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V (V3:AEP,CET,SP/V7:AEP,CET,UK,SP,IT,KR/V7L) 1-162-199-31 CERAMIC 10PF 5% 50V 1-162-199-31 CERAMIC 10PF 5% 50V 1-126-959-11 ELECT 0.47uF 20% 50V 1-126-963-11 ELECT 4.7uF 20% 50V
C15 C17 C18 C19
1-164-156-11 1-164-156-11 1-126-960-11 1-162-995-11
C19
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
0.1uF 25V 0.1uF 25V 1uF 20% 50V 0.022uF 50V (V3:AR/V7:CND,AR,AUS,TW,E4) 1-162-974-11 CERAMIC CHIP 0.01uF 50V (V3:AEP,CET,SP/V7:AEP,CET,UK,SP,IT,KR/V7L)
C20
1-162-995-11 CERAMIC CHIP
C20
1-162-974-11
C21 C22 C23
1-162-228-31 1-115-156-11 1-126-964-11
C24 C25
1-162-974-11 CERAMIC CHIP 1-162-964-11 CERAMIC CHIP
C26 C27 C28
42
0.022uF 50V (V3:AR/V7:CND,AR,AUS,TW,E4) CERAMIC CHIP 0.01uF 50V (V3:AEP,CET,SP/V7:AEP,CET,UK,SP,IT,KR/V7L) CERAMIC 4.7PF 10% 50V CERAMIC CHIP 1uF 10V ELECT 10uF 20% 50V 0.01uF 0.001uF
50V 10% 50V (EXCEPT V7L) 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V (V7L) 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V (V3:AEP,CET,SP/V7:AEP,CET,UK,SP,IT,KR/V7L) 1-130-014-00 FILM 470PF 5.00% 50V (V7L)
Ref. No.
Part No.
Description
Remark
C29
1-130-044-00 FILM
C30 C31
1-162-907-11 1-130-014-00
C32
1-162-195-31
C36
1-162-915-11
C152 C153 C154 C155 C156
1-162-964-11 1-104-657-11 1-126-925-11 1-107-826-11 1-104-657-11
CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT
0.001uF 47uF 470uF 0.1uF 47uF
10% 20% 20% 10% 20%
50V 10V 10V 16V 10V
C171 C252 C253 C254 C255
1-126-964-11 1-162-964-11 1-104-664-11 1-126-935-11 1-107-826-11
ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP
10uF 0.001uF 47uF 470uF 0.1uF
20% 10% 20% 20% 10%
50V 50V 10V 10V 16V
C256 C271 C314 C316 C317
1-104-657-11 1-126-964-11 1-104-657-11 1-126-960-11 1-104-662-11
ELECT ELECT ELECT ELECT ELECT
47uF 10uF 47uF 1uF 22uF
20% 20% 20% 20% 20%
10V 50V 10V 50V 25V
C320 C341 C343 C345 C346
1-162-995-11 1-126-936-11 1-162-974-11 1-162-974-11 1-162-974-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.022uF 3300uF 0.01uF 0.01uF 0.01uF
C347 C348 C349 C351 C401
1-126-923-11 1-104-658-11 1-162-974-11 1-104-657-11 1-104-658-11
ELECT ELECT CERAMIC CHIP ELECT ELECT
220uF 100uF 0.01uF 47uF 100uF
C402 C801
C802 C805
1-126-964-11 ELECT 10uF 20% 50V 1-162-974-11 CERAMIC CHIP 0.01uF 50V (-12)(V3:AEP,CET,SP/V7:AEP,CET,KR,SP,UK) 1-164-156-11 CERAMIC CHIP 0.1uF 25V(-11) (-12:V3:AR/V7:CND,AR,AUS,IT,TW/V7L) 1-104-657-11 ELECT 47uF 20% 10V 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C810 C841 C842 C843 C844
1-162-927-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11
C851 C891
1-162-919-11 CERAMIC CHIP 1-162-964-11 CERAMIC CHIP
C801
5.00% 50V (V7L) CERAMIC CHIP 2PF 0.25PF 50V FILM 470PF 5.00% 50V (V7L) CERAMIC 4.7PF 10% 50V (V3:AEP,CET,SP/V7:AEP,CET,UK,SP,IT,KR/V7L) CERAMIC CHIP 10PF 0.5PF 50V (V7L)
CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
100PF
1-781-962-11 1-577-072-11 1-795-277-11 1-760-738-61
20% 20%
10V 10V 50V 10V 10V
5%
50V 25V 25V 25V 25V
22PF 0.001uF
5% 10%
50V 50V
FILTER, CERAMIC (V3/V7) FILTER, CERAMIC (V7L) CERAMIC FILTER (V7L) FILTER, CERAMIC (V3/V7)
CN801 CN802
20% 20%
50V 16V 50V 50V 50V
100PF 0.1uF 0.1uF 0.1uF 0.1uF
CF1 CF1 CF2 CF2
20%
1-784-777-11 CONNECTOR, FFC 16P 1-784-737-11 CONNECTOR, FFC 15P
CFD-V3/V7/V7L Ver 1.5
MAIN Ref. No.
Part No.
Description
Remark
Ref. No.
JC401
* CNP303 1-815-445-11 PIN, CONNECTOR 4P * CNP304 1-815-552-11 PIN, CONNECTOR (PC BOARD) 4P * CNP305 1-784-732-11 CONNECTOR, FFC 10P (V3/V7)
* * * *
CT1 CT2 CT3 CT4
1-141-637-11 CAP, VAR (TUNING) 1-141-604-11 CAP, ADJ (LW FREQUENCY COVERAGE)(V7L) 1-141-622-21 CAP, ADJ 50PF (LW TRACKING) (V7L)
1-141-637-11 1-141-637-11 1-141-637-11 1-141-637-11
1-565-385-11 1-565-386-11 1-573-287-11 1-565-385-11
L1 L2
1-406-998-11 COIL, AIR-CORE (FM TRACKING) 1-411-949-11 COIL, AIR-CORE (FM FREQUENCY COVERAGE) (V3/V7:CND,AR,AUS,TW,E4,AEP,CET,UK,SP/V7L) 1-406-957-21 COIL (WITH CORE) (FM FREQUENCY COVERAGE) (V7:IT) 1-754-175-11 ANTENNA, FERR ROD (AM TRACKING) (EXCEPT V7L) 1-754-189-11 ANTENNA, FERR ROD (LW TRACKING) (V7L)
L2
CAP, VAR (FM TRACKING) CAP, VAR (FM FREQUENCY COVERAGE) CAP, VAR (AM/LW TRACKING) CAP, VAR (AM/LW FREQUENCY COVERAGE)
L3 L3 L4
L4 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61
DIODE DIODE DIODE DIODE DIODE
1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17
D304 D305 D306 D308 D309
8-719-988-61 8-719-083-93 8-719-988-61 8-719-082-09 8-719-988-61
DIODE DIODE DIODE DIODE DIODE
1SS355TE-17 KDS120-RTK 1SS355TE-17 KDZ3.9V-RTK 1SS355TE-17
D310 D311 D314
8-719-059-97 LED 8-719-084-00 DIODE 8-719-988-61 DIODE
8-759-829-93 8-759-426-51 8-759-646-86 8-759-696-92
IC IC IC IC
HOLDER, CABLE 4P HOLDER, CABLE 5P HOLDER, CABLE 2P HOLDER, CABLE 4P
1-406-040-00 COIL (OSC) (AM FREQUENCY COVERAGE) (EXCEPT V7L) 1-424-771-11 COIL (OSC) (LW FREQUENCY COVERAGE) (V7L)
L-34HD (OPR/BATT) KDZ7.5V-RTK 1SS355TE-17
IC1 IC304 IC401 IC801
Remark 0
KH2 KH306 KH801 KH902
D1 D2 D301 D302 D303
Description
1-216-864-11 SHORT
CNP305 1-784-734-11 CONNECTOR, FFC 12P (V7L)
CV1 CV2 CV3
Part No.
TA2111N BA5417 MM1468XD uPD789316GK-903
Q1 Q2 Q101 Q201 Q309
8-729-054-02 8-729-054-02 8-729-054-24 8-729-054-24 8-729-021-82
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
KRA302-RTK KRA302-RTK (V7L) KRC410-RTK KRC410-RTK 2SD2396K
Q310 Q311 Q312 Q401 Q402
8-729-036-86 8-729-055-41 8-729-054-19 8-729-037-03 8-729-054-16
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
KTC3203Y-AT KTB1241Y-AT KRC405-RTK KTA1266GR-AT KRC402-RTK
Q405 Q409 Q801
8-729-037-03 TRANSISTOR 8-729-212-02 TRANSISTOR 8-729-054-18 TRANSISTOR
KTA1266GR-AT 2SC2120-Y KRC404-RTK
ICP301 1-533-674-21 IC LINK(-11)
R1 R2 R3 R4 R5
1-216-813-11 1-216-815-11 1-216-827-11 1-216-827-11 1-216-809-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
220 330 3.3K 3.3K 100
5% 5% 5% 5% 5%
R8 R9 R11 R20
1-216-837-11 1-216-837-11 1-216-833-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
22K 22K 10K 1K
R20
1-216-809-11 METAL CHIP
100
5% 1/16W 5% 1/16W 5% 1/16W 5% 1/16W (EXCEPT V7L) 5% 1/16W (V7L)
R30 R151 R153 R154 R251
1-216-813-11 1-216-829-11 1-216-817-11 1-216-025-11 1-216-829-11
METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP
220 4.7K 470 100 4.7K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/10W 1/16W
R253 R254 R314
1-216-817-11 METAL CHIP 1-216-025-11 RES-CHIP 1-216-829-11 METAL CHIP
470 100 4.7K
5% 5% 5%
1/16W 1/10W 1/16W
J301
1-815-325-11 JACK (i)
JC1 JC2 JC4
1-216-864-11 SHORT 1-216-864-11 SHORT 1-216-809-11 METAL CHIP
0 0 100
JC5 JC6
1-216-864-11 SHORT 1-216-864-11 SHORT
0 0
JC7 JC302 JC303 JC305 JC306
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
0 (EXCEPT E4/V7L) 0 0 0 0
JC310
1-216-864-11 SHORT
SHORT SHORT SHORT SHORT SHORT
5%
1/16W (-11)
1/16W 1/16W 1/16W 1/16W 1/16W (-12)
0
43
CFD-V3/V7/V7L Ver 1.5
MAIN Ref. No.
PRE Part No.
Description
Remark
R315 R319
1-216-821-11 METAL CHIP 1-216-829-11 METAL CHIP
1K 4.7K
5% 5%
1/16W 1/16W
R340 R341 R342 R343
1-216-827-11 1-216-827-11 1-216-827-11 1-216-827-11
3.3K 3.3K 3.3K 3.3K
5% 5% 5% 5%
R343
1-216-821-11 METAL CHIP
1K
5%
1/16W 1/16W 1/16W 1/16W (-11) 1/16W (V7:IT)
R344 R345 R346
1-216-813-11 METAL CHIP 1-216-821-11 METAL CHIP 1-216-821-11 METAL CHIP
220 1K 1K
R348
1-216-821-11 METAL CHIP
1K
R349
1-216-815-11 METAL CHIP
330
5% 1/16W 5% 1/16W 5% 1/16W (EXCEPT IT)(-12) 5% 1/16W (EXCEPT IT)(-12) 5% 1/16W
R350 R351
1-216-825-11 METAL CHIP 1-216-821-11 METAL CHIP
2.2K 1K
5% 5%
R351
1-216-819-11 METAL CHIP
680
5%
R352
1-216-821-11 METAL CHIP
1K
5%
R352
1-216-819-11 METAL CHIP
680
5%
R353
1-216-821-11 METAL CHIP
1K
5%
R353
1-216-819-11 METAL CHIP
680
5%
R354
1-216-819-11 METAL CHIP
1K
5%
R354
1-216-819-11 METAL CHIP
680
5%
R355
1-216-821-11 METAL CHIP
1K
5%
R360 R386 R401 R402 R403
1-216-845-11 1-216-827-11 1-216-845-11 1-216-833-11 1-216-837-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
100K 3.3K 100K 10K 22K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R404 R413
1-216-821-11 METAL CHIP 1-216-829-11 METAL CHIP
1K 4.7K
5% 5%
R414
1-216-831-11 METAL CHIP
6.8K
5%
R415
1-216-831-11 METAL CHIP
6.8K
5%
R415
1-216-827-11 METAL CHIP
3.3K
5%
1/16W 1/16W (-11) 1/16W (-11) 1/16W (-11) 1/16W (-12)
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
Ref. No.
1/16W (-11) 1/16W (-12) 1/16W (-11) 1/16W (-12) 1/16W (-11)
R416 R417 R418 R801 R805
1-216-829-11 1-216-833-11 1-216-833-11 1-216-801-11 1-216-849-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
4.7K 10K 10K 22 220K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R806 R809 R810 R811 R812
1-216-813-11 1-216-821-11 1-216-809-11 1-216-833-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
220 1K 100 10K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R813
1-216-821-11 METAL CHIP
1K
5%
1/16W
Description
Remark
1-216-821-11 METAL CHIP
1K
5%
1/16W
R815 R816 R818 R819 R851
1-216-809-11 1-216-809-11 1-216-809-11 1-216-809-11 1-216-829-11
100 100 100 100 4.7K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
S351
1/16W 1/16W (-11) 1/16W (-12) 1/16W (-11) 1/16W (-12)
Part No.
R814
1-572-300-11 SWITCH, LEVER SLIDE (FUNCTION)
T1 T2
1-424-702-11 COIL, FM DET (FM IF) 1-424-703-11 COIL, AM IFT (AM/LW IF)
***************************************************** * *
A-3062-296-A PRE BOARD, COMPLETE (V7L) A-3347-104-A PRE BOARD, COMPLETE (V3/V7)
************************ C101 C102 C103 C104 C105
1-162-964-11 1-104-664-11 1-165-176-11 1-162-966-11 1-162-923-11
CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP
0.001uF 47uF 0.047uF 0.0022uF 47PF
10% 20% 10% 10% 5%
50V 10V 16V 50V 50V
C106 C107 C201 C202 C203
1-126-960-11 1-162-962-11 1-162-964-11 1-104-664-11 1-165-176-11
ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP
1uF 470PF 0.001uF 47uF 0.047uF
20% 10% 10% 20% 10%
50V 50V 50V 10V 16V
C204 C205 C206 C207 C301
1-162-966-11 1-162-923-11 1-126-960-11 1-162-962-11 1-104-665-11
CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT
0.0022uF 47PF 1uF 470PF 100uF
10% 5% 20% 10% 20%
50V 50V 50V 50V 10V
C302 C303 C304 C305 C306
1-104-665-11 1-104-665-11 1-104-664-11 1-162-962-11 1-162-970-11
ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP
100uF 100uF 47uF 470PF 0.01uF
20% 20% 20% 10% 10%
10V 10V 10V 50V 25V
C307 C310
1-162-966-11 CERAMIC CHIP 1-164-230-11 CERAMIC CHIP
0.0022uF 10% 220PF 5%
CN303 CN302
1-695-371-31 CONNECTOR, FFC 10P (V3/V7) 1-784-773-11 CONNECTOR, FFC 12P (V7L)
IC301
8-759-264-71 IC
TA2068N
44
JC301 JC302 JC303 JC304 JC309
1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11
SHORT SHORT SHORT SHORT SHORT
0 0 0 0 0 (V7L)
50V 50V (V7L)
CFD-V3/V7/V7L Ver 1.5
PRE Ref. No.
Part No.
Description
Remark
POWER
VOL SEL
Ref. No.
Part No.
*
1-680-679-12 VOLUME BOARD
VOLUME
Description
Remark
************* Q301 Q302
8-729-920-75 TRANSISTOR 8-729-054-16 TRANSISTOR
2SC2412-T146 KRC402-RTK (V7L)
R101 R102 R103 R104 R105
1-216-835-11 1-216-807-11 1-216-843-11 1-216-825-11 1-216-835-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
15K 68 68K 2.2K 15K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R106 R110 R111 R201 R202
1-216-825-11 1-216-809-11 1-216-829-11 1-216-835-11 1-216-807-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
2.2K 100 4.7K 15K 68
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R203 R204 R205 R206 R210
1-216-843-11 1-216-825-11 1-216-835-11 1-216-825-11 1-216-025-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP
68K 2.2K 15K 2.2K 100
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/10W
R211 R301 R302 R303 R304
1-216-829-11 1-216-857-11 1-216-829-11 1-216-829-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
4.7K 1M 4.7K 4.7K 1K
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R305 R306 R307 R308 R309
1-216-817-11 1-216-831-11 1-216-797-11 1-216-837-11 1-216-805-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
470 6.8K 10 22K 47
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
R310
1-216-857-11 METAL CHIP
1M
5%
R314 R315
1-216-817-11 METAL CHIP 1-216-817-11 METAL CHIP
470 470
5% 5%
1/16W (V7L) 1/16W 1/16W
C123 C124 C223 C224
1-115-870-11 1-162-968-11 1-115-870-11 1-162-968-11
ELECT CERAMIC CHIP ELECT CERAMIC CHIP
0.47uF 0.0047uF 0.47uF 0.0047uF
20% 10% 20% 10%
50V 50V 50V 50V
5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W
* KH307
1-565-386-11 HOLDER, CABLE 5P
R123 R124 R223 R224
1-216-821-11 1-216-831-11 1-216-821-11 1-216-831-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP
1K 6.8K 1K 6.8K
RV352
1-227-188-11 RES, VAR, CARBON 20K/20K (VOLUME)
S355
1-786-141-11 SWITCH PUSH (MEGA BASS)
***************************************************** MISCELLANEOUS
*************
S301
T301
1-786-126-11 SWITCH, SLIDE (REC/PB) 1-416-041-11 TRANSFORMER, BIAS OSCILLATION
****************************************************** *
1-680-683-12 POWER BOARD
***********
* * * *
59 111 112 112 114
1-452-899-11 1-757-584-11 1-757-688-11 1-757-845-11 1-757-583-11
124 252
1-757-689-11 CABLE FLEXIBLE FLAT 16P X-2162-709-1 CHASSIS ASSY (CDP), MOTOR (SPINDLE) (INCLUDING M701) 8-848-483-05 OPTICAL PICK-UP KSS-213C 1-501-883-21 ANTENNA, TELESCOPIC 1-543-876-11 HEAD (ERASE)
0 253 ANT1 HE901
MAGNET CABLE FLEXIBLE FLAT 15P CABLE FLEXIBLE FLAT 10P (V3/V7) FFC 12P (V7L) CABLE FLEXIBLE FLAT 16P
HRP901 1-500-668-11 HEAD,MAGNETIC(RECORD/PLAYBACK) M601 A-3320-446-A MOTOR ASSY (CAPSTAN/REEL) (INCLUDING PULLEY) M702 X-2625-769-1 GEAR ASSY (MB), MOTOR (SLED) (INCLUDING GEAR) S601 1-762-679-11 SWITCH, LEAF (MD POWER) S801 1-692-960-11 SWITCH, PUSH (1 KEY) (CD DOOR OPEN/CLOSE)
* KH904 1-573-287-11 HOLDER, CABLE 2P ****************************************************** *
1-682-707-11 VOL SEL BOARD(E4)
SP101 SP101 SP201 SP201 0 T901
1-529-723-11 1-529-723-21 1-529-723-11 1-529-723-21 1-433-576-11
SPEAKER (10cm) (L-CH) (V3) SPEAKER (10cm) (L-CH) (V7/V7L) SPEAKER (10cm) (R-CH) (V3) SPEAKER (10cm) (R-CH) (V7/V7L) TRANSFORMER, POWER (CND,TW)
0 T901 0 T901
1-435-921-11 TRANSFORMER, POWER (EXCEPT CND,TW,E4) 1-435-922-11 TRANSFORMER, POWER (E4)
***************
***************************************************** 0 S901
1-552-921-00 SWITCH,POWER(VOLTAGE SELECTOR)
******************************************************
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
45
CFD-V3/V7/V7L Ver 1.2 2001.08
Ref. No.
Part No.
Description
Remark
ACCESSORIES & PACKING MATERIALS
**************************** 0 0 0 0 0
1-577-287-11 1-569-008-21 1-690-952-12 1-696-819-11 1-769-412-13
0 0 0
1-770-019-12 1-776-985-11 1-783-952-11 3-227-154-11
CORD, POWER (V7:TW) ADAPTOR,CONVERSION (V7:E4) CORD, POWER (V7:CND) CORD, POWER (V7:AUS) CORD, POWER (V3:AEP,CET,SP/V7:AEP,IT,CET,UK,SP,E4/V7L)
ADAPTOR, CONVERSION PLUG 3P (V7:UK) CORD, POWER (V7:KR) CORD, POWER (V3:AR/V7:AR) MANUAL, INSTRUCTION (ENGLISH,FRENCH) (V7:CND) 3-227-154-21 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (V3:AEP,AR,SP/V7:AEP,AR,AUS,SPE4,KR/V7L) 3-227-154-31 MANUAL, INSTRUCTION (FRENCH,GERMAN) (V3:AEP,SP/V7:AEP,SP/V7L:AEP) 3-227-154-41 MANUAL, INSTRUCTION (DUTCH,PORTUGUESE) (V3:AEP/V7:AEP,E4/V7L:AEP) 3-227-154-51 MANUAL, INSTRUCTION (ITALIAN)(V7:AEP,IT) 3-227-154-61 MANUAL, INSTRUCTION (SWEDISH,FINNISH) (CET) 3-227-154-71 MANUAL, INSTRUCTION (POLISH)(CET) 3-227-154-81 MANUAL, INSTRUCTION (CZECK,HUNGARIAN) (CET) 3-227-154-91 MANUAL, INSTRUCTION (RISSIAN,SLOVAK) (CET) 3-230-889-11 MANUAL, INSTRUCTION (ENGLISH,TRADITIONAL CHINESE) (V7:TW) 3-230-889-21 MANUAL, INSTRUCTION (KOREAN) (V7:KR) 3-703-044-26 LABEL, CAUTION (V7:CND)
* ************************************************************** ************** HARDWARELIST
************** #1 #2 #3 #4 #5
7-685-647-79 7-685-648-79 7-685-853-04 7-621-775-20 7-682-548-04
SCREW +BVTP 3X10 TYPE2 N-S SCREW +BVTP 3X12 TYPE2 N-S SCREW +BVTT 2X6 (S) SCREW +B 2.6X5 SCREW +B 3X8
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
46
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
CFD-V3/V7/V7L SERVICE MANUAL
Canadian Model UK Model Australian Model CFD-V7
AEP Model
2002.06
CFD-V3/V7/V7L
E Model CFD-V3/V7
SUPPLEMENT - 1 File this Supplement with the Service Manual.
Subject : CHANGE OF CD MECHANISM (SPM-02027)
CD mechanism changed to KSM-213RDP from KSM-213CDP. Please check serial No. when you exchange the parts of CD mechanism. • Serial No. of changed model CFD-V3 : No. 1,076,878 and later CFD-V7 : No. 1,387,153 and later CFD-V7L : (not changed)
CFD-V3/V7/V7L
OPTICAL PICK-UP SECTION (KSM–213RDP)
254
257 256
258 259 256
251
M701
252 255 M702
253 (including M701)
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Ref. No. 251 252 253 0 254 * 255
2
Part No.
Description
Remark
3-713-786-51 SCREW (M2X3) 2-626-908-01 SHAFT, SLED X-2162-707-1 CHASSIS ASSY (RDP) (RP), MOTOR (SPINDLE) (INCLUDING M701) 8-820-161-02 OPTICAL PICK-UP KSS-213R 2-647-408-02 GEAR (B)
Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Ref. No.
Part No.
Description
256 * 257 * 258 * 259 M702
2-169-388-01 2-169-065-01 2-169-385-01 2-169-384-01 X-2162-712-1
TAPPING (M2), +PWB GEAR (A) SPRING, SLED SHAFT (S), GEAR GEAR ASSY (R) (RP), MOTOR (MB) (SLED) (INCLUDING GEAR)
Remark
CFD-V3/V7/V7L
MEMO
3
CFD-V3/V7/V7L
REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 1.1
Date 2001.02 2001.04
1.2
2001.08
1.3
2002.06
1.4 1.5
2003.06 2003.12
Description of Revision New Model addition CFD-V3: Singapore, Argentina model CFD-V7: Singapore, Argentina, Australian, Taiwan model Change of Schematic Diagram. Cahnge of Printed Wiring Boards. Change of Exploded views. Change of Electrical Parts List Model addition CFD-V7: E4, Korean model Boards change (Last digit:-13). ( ENG-01016) SUPPLEMENT-1 ( SPM-02027) Correction of exploded views (7-6. CD BLOCK SECTION). Correction of boards last digit. (SPM-03014) Blue model addition for CFD-V7 Ausiralian model. Writing-together abolition of a former type and new type board of parts list. (SPM-03063)
