Chilliwack Alliance Church - Renkus

Transcript

Loudspeaker System Recommendation Chilliwack Alliance Church Prepared for: Contact Distribution Application Engineering Renkus-Heinz, Inc. April 24, 2014 Contents Recommendation ---------------------------------------------------------------------------------------------------------- 2-3 Equipment List ---------------------------------------------------------------------------------------------------------------- 4 Array Configuration ----------------------------------------------------------------------------------------------------------- 5 EASE mappings ------------------------------------------------------------------------------------------------------------ 6-7 Product Datasheets ---------------------------------------------------------------------------------------------- Following 8 Design Goals Renkus-Heinz has been asked to recommend a sound reinforcement system for the Chilliwack Alliance Church. Our design goals were to provide a left/right line array solution with front fills for use with contemporary and traditional services.. Of course this performance must be delivered evenly to all seats in the house. Room Details Approximate room dimensions and photographs have been provided to Renkus-Heinz. The room is tapered, approximately 80 feet wide in the front and 150 feet wide in the rear with a sloping ceiling from 43 to 27 feet high in the back. There is also a balcony section which has no under seating. Ceilings appear to be drop-tiles, carpeted floors and padded pews. Recommended Loudspeaker System Renkus-Heinz recommends the CF101LA as an alternative to the VARIA modular array modules. This will be a more economical solution sacrificing only small amounts of coverage variances and sound quality. These can be specified as self-powered with built-in DSP or externally powered. If they are externally powered, we recommend external DSP processing for at least every two cabinets for best performance. Since the CF101LA module is a fixed curve array module, the maximum allowable in this configuration will be 4 cabinets per side. This will reduce max SPL slightly over the previously recommended VARIA system. Front fills across the stage can be CF61R or CFX61, we have modeled four them to be adequate. Loudspeaker mounting location It has been specified that speaker locations must be above the curtain valence which is 24 feet high. This puts the CF101LA arrays at a mounting height of 33 feet AFF. Optional Subwoofers Subwoofers to compliment the above system are recommended to be a minimum of 8x CF15S. These can be placed under or on the stage or even flown. Understanding EASE Mappings in Appendix The system has been designed with the aid of EASE, Enhanced Acoustic Simulator for Engineers, a product of the Ahnert-Feistel Media Group, GmbH, Berlin, Germany. EASE is the international standard for sound-system design and prediction and has been proven accurate in thousands of successful sound system installations world-wide. For more on EASE and sound system prediction, please see AFMG’s website: http://ease.afmg.eu/ “System Coverage” maps show system coverage averaged over two octaves, at the frequency range indicated, of the seating areas at ear height. The mapping is predicted Direct Sound Pressure Level in dB. No room effects are included. These maps do not represent how loud the system will get, but rather consistency of coverage. The “Maximum SPL, A-Weighted” map shows the approximate maximum level the system would reach as shown on an SPL meter set to read broad band, A-weighted, fast. 2 Important Disclaimer: All simulations have been done with industry standard techniques and software using information supplied by others. They are believed to be accurate within normal tolerances for such simulations providing the data supplied was accurate. Renkus-Heinz makes no guarantee that the final system will perform as simulated. Renkus-Heinz guarantees only that any Renkus-Heinz equipment will perform to its published specifications within normal industry tolerances. The above is a recommendation only and is not to be considered or represented as a design by RenkusHeinz. WARNING! Hanging loudspeakers is a serious undertaking that should be done only by qualified and experienced personnel. Check with an Architect or Structural Engineer to verify any building attachment points. Renkus-Heinz is not responsible for any non-Renkus-Heinz products or for any misuse of Renkus-Heinz products. Thank you for the opportunity of making this recommendation. 3 Appendix 1, Equipment List Item RH Part Number Qty. Main L/R Array module CF101LA-52R 8 Flying Hardware for main arrays RHANG-101LA 2 Optional Subwoofers CF15S-5R 8 Optional caster kit for subs CSTRS-15S 8 4 Appendix 2, Array configuration 5 Appendix 3, EASE Mappings System Coverage at low frequencies, 100-400 Hz. Average System Coverage at mid frequencies, 500-2000 Hz. average 6 System Coverage at high frequencies, 2,500-10,000 Hz. average System Coverage, maximum SPL A-weighted 7 End of Recommendation Product datasheets on following pages 8 Modular Point Source Array CF-CFX101LA & CF/CFX15S MODULAR POINT SOURCE ARRAY LOUDSPEAKER SYSTEMS R E N K U S - H E I N Z A U D I O O P E R AT I O N S N E T W O R K CF/CFX Modular Point Source Array CF15S INTRODUCING THE CF/CFX Modular Point Source Array Designed for power, portability and versatility, the CF/CFX101LA from RenkusHeinz is the ideal solution for today’s small and mid-sized venues, including auditoria, night clubs, theaters and houses of worship. With the flexibility to be flown, ground-stacked or pole-mounted, the CF/CFX101LA delivers the performance and pattern control of a line array, with the clarity of a point source system, in a compact, sleek and affordable design that’s equally at home as a portable system or a permanent installation. Alone or combined with the CF/CFX15S subwoofer, the CF/CFX101LA can be flown, ground-stacked, or pole-mounted, or used as a center cluster to complement an existing left-right system, making it the perfect solution for a wide range of installed or portable sound needs. CF101LA HIGHER POWER DENSITY Up to four CF/CFX101LA cabinets can be arrayed to provide a 90 x 60 degree coverage pattern, delivering from 9 dB to 12 dB more output and tighter vertical pattern control than a conventional single cabinet. Traditional line arrays require two or three times as many cabinets to provide the same range of coverage. MODULAR POINT SOURCE WAVEGUIDE - TUNED CONIC DIVERTER When it comes to innovation, once again Renkus-Heinz leads the way. Our new Tuned Conic Diverter carefully manipulates the curvature of the wavefront within the horn so that it's curvature matches the curvature of the array. As sound leaves the compression driver, it's wavefront expansion is at first spherical matching the shape of the bounding side walls. As sound progresses through the horn, it's wavefront is progressively flatened as it passes through a Tuned Conic Diverter which slows the wavefronts expansion at the center relative to the sides, modifying it's curvature to match the shape of the cabinet. With the introduction of the CF/CFX Modular Point Source Array, we have created a modular point source system, fully conforming to the true array principle that is completely free of audible and measurable comb filtering. What you experience is the clarity of a single cabinet, with the power and coverage to satisfy everyone in the audience. Tuned Conic Diverter Page 2 CF/CFX Modular Point Source Array DESIGNED FOR RUGGED DEPENDABILITY Heavy-duty birch ply cabinets, ultra-durable coatings and tough, reinforced hardware are designed to withstand the rigors of the road. MULTI-ANGLE POLE SOCKET All CF/CFX101LA cabinets come standard with an integral multi-angle pole socket allowing the cabinet to be supported on a standard 35mm loudspeaker stand, or on a sturdy pole attached to the subwoofer. This allows the full-range cabinet to be angled straight ahead, up or down as the situation demands for optimum coverage and performance. SAFE & SIMPLIFIED HARDWARE Simple, rugged, integral hardware allows for maximum versatility, maximum safety, and fast setup and teardown. CF/CFX101LA hardware has been designed to work either way up so left and right systems can be setup symmetrically without the need for mirror image cabinets. CF/CFX15S matched subwoofers employ the same simple yet sturdy hardware enabling the system to be flown beneath the subwoofer. QUALITY COMPONENTS Renkus-Heinz uses only the highest quality, lowest-tolerance components and hardware designed for peak performance. From the precisiontuned crossover network, to rugged dependable hardware, CF/CFX101LA delivers. Page 3 CF/CFX Modular Point Source Array CF/CFX101LA The CF/CFX101LA Point Array Module has been designed with your requirements for flexibility in mind. Each cabinet can be pole mounted, flown from a frame or suspended using M10 eyebolts. Suited equally to fixed installation or portable applications each array module offers a consistent 90 degree horizontal and tight 15 degree vertical coverage. Neodymium magnets on the single 10” Low Frequency woofer and dual 1” High Frequency compression drivers provide the ideal balance of power and portability, while the revolutionary performance of the Tuned Conic Diverter waveguide ensures the smoothest possible transition between cabinets. CF/CFX Point Array is a true point source arrayable system offering the benefits of both line and point source arrays. • Outstanding Performance • Dual 1” HF Drivers and High Power 10” Woofer • Neodymium Magnet Structures • Great Versatility • Exclusive Tuned Conic Diverter • Tight Pattern Control • Reliable, Easy-To-Use Hardware • Flexible Input Configurations CFX101LA-8 Connector Plate • Switchable Biamp / Passive HIGH FREQUENCY ARRAY CONTROL As the CF/CFX101LA can be used in many and varied combinations simple High Frequency level control switches are provided on the back of each cabinet. The user can select between a Flat response for a single cabinet, or boost the HF by +6dB or +9dB depending on how many cabinets are in the array and how much throw is required. Page 4 CF/CFX101LA CF/CFX Modular Point Source Array CF/CFX15S Subwoofer CF15S and CFX15S-8 subwoofers were developed as companion pieces to the CF/CFX series point source array modules. They provide the high impact sub bass energy needed in many venues and also serve as a mounting platform for both stacked and flown arrays. Along with being a dedicated companion subwoofer to the CF/CFX101LA Point Source Array, it can be used to create directional cardiod and steerable arrays as well. Using RHAON, these arrays can then be "steered" to put sub frequencies where they are needed, avoiding floor, ceiling, and rear wall reflections for maximum clarity and impact. CF/CFX15S • Powerful 15” Subwoofers • Neodymium Magnet Structures Neodymium Magnet Structure Woofer • Outstanding Versatility • High Performance, High Power Woofers • Flexible Input Configurations • RHAON Ready Ground Stack with dual array modules & single subwoofer Floor System with single array module & subwoofer Floor System with dual array modules & dual subwoofers Page 5 CF/CFX Modular Point Source Array EASE FOCUS EASE Focus allows users and system designers to quickly and accurately predict the response of the array. Simply define the audience areas and you can easily place the array, add or remove cabinets and adjust its height, location and angle until you get the desired results in the simulation. RENKUS-HEINZ AUDIO OPERATIONS NETWORK Passive, powered or networked, you can choose the system configuration that meets your needs at any time. Whenever you are ready for Ethernet audio networking, your CF loudspeakers are too. At the factory or in the field, the CFX passive connector plate can be easily replaced by one of five PF Series intelligent Class D digital amplifiers. A Windows GUI empowers RHAON users to connect each Renkus-Heinz powered loudspeaker to a CobraNet network, control 8 parametric EQ filters, up to 340 ms of delay and dynamics processing via onboard DSP, and supervise both the amplifier and drivers. Connect Control Beams / Presets Supervise SELF POWERED & EXTERNALLY POWERED The CF/CFX101LA Series is available as a passive loudspeaker for use with external amplification, or with Renkus-Heinz’s highly acclaimed PF Series Intelligent Digital Amplification. The PF Series delivers audiophile-quality performance, ultra-low distortion and unparalleled efficiency in a sleek, lightweight design. Page 6 CF/CFX Modular Point Source Array CF/CFX15S CF/CFX101LA Sensitivity CF101LA-5, -5R & -52R: CFX101LA-8: Max SPL: Dispersion: Freq. Response: HF Drivers: LF Driver: 1.0 V for rated power output 96 dB (1W/1m) 126 dB peak 90O Horizontal, 15O Vertical 60 Hz to 20 kHz Two 1” SSDCDXI-1730-8 HF Neodymium drivers; 75 W RMS @ 8 Ohms, 150 W pgm each CF101LA: 10” Neodymium woofer, model SSL10-8, 250 W RMS @ 8 Ohms, 500 W pgm CFX101LA-8: 10” Neodymium woofer, model SSL10-10, 250 W RMS @ 8 Ohms, 500 W pgm Crossover: 1.0 kHz Enclosure: Multi-ply hardwood, perforated metal grille Power CF101LA-5, -5R & -52R: 115 V AC or 230 V AC, 50/60 Hz CFX101LA-8: 500 W pgm at 8 Ohms Controls: Array Balancing Connectors CFX101LA-8: Neutrik 4-pin Speakon style connectors, screw terminals Finish: Black or white; custom colors available Weather resistant treatment available Hardware: Four Metric M10 attachment points Multi-angle pole socket Associated Hardware: RHANG101LA Flybar POLE-CF101 Mounting Pole Dimensions: 13" H x 23 3/4" W x 15" D (33 cm x 60.3 cm x 38.1cm) Weight CF101LA-5 & -5R: 56 Lbs. (25.4 Kg) net CF101LA-52R: 58 Lbs (26.3 Kg) net CFX101LA-8: 54 Lbs (24.5 Kg) net PF1-500 DIGITAL AMPLIFIER Power: Freq. Resp: THD Distortion: Hum & Noise: Damping: Input: Sensitivity: CMR: Controls: Power Connector: Input: 500 W RMS @ 4 Ohms +0.0, -.5 dB, 20 Hz to 20 kHz < 0.02% typical <100 dB (A weighted) >100 10K Ohm balanced differential 1.0 V for RPO 74 dB Gain (screwdriver adjustable) IEC Power connector Looping XLR; female in, male out (pin 1 chassis, pin 2 +, pin 3 -) Power: Switchable, 115 or 230 V AC, 50/60 Hz 5 A @ 120 V, 2.5 A @ 240 V Idle current: 400 ma @120 V; 200 ma @ 240 V Max inrush current: 1 A Sensitivity CF15S-5 & -5R: CFX15S-8 : Max SPL CF15S-5 & -5R: CFX15S-8: Freq. Resp: LF Driver: 1.0 V for RPO 97 dB (1W/1m) 127 dB peak 129 dB peak 40 Hz to 120 Hz CF15S: 15" woofer with Neodymium magnet, model SSL15-20; 400 W RMS @ 4 Ohms, 800 W pgm CFX15S-8: 15" woofer with Neodymium magnet, model SSL15-17; 400 W RMS @ 8 Ohms, 800 W pgm Enclosure: 13-ply hardwood, perforated metal grille Finish: Black or white; custom colors available Weather resistant treatment available Power CF15S-5 & -5R: 115 V AC or 230V AC CFX15S-8: 800 W pgm at 8 Ohms Connectors CF15S-5 & -5R: See amplifier specifications CFX15S-8: Screw terminals & looping 4-pin Neutrik Speakon style connectors Hardware: 8-point univ. mtg. hdw. (Metric M10 threads) Threaded pole socket, Integral flying hardware Optional - heavy duty wheels Dimensions: 19" H x 23 1/4” W x 22 1/2" D (48.3 cm x 59 cm x 56.5 cm) Weight CF15S-5 & -5R: 117 Lbs (53.4 Kg) net CFX15S-8: 112 Lbs (51 Kg) net PF1-500R RHAON EMPOWERED AMPLIFIERS The PF1-500R is identical to the PF1-500 except for the addition of the RHAON Network Interface; additional capabilities include: Inputs: CobraNet: Dual RJ45 connectors; accept Cat 5 copper cable. AES/EBU: Phoenix connectors; Analog: Phoenix connectors Digital Format: 16, 20 or 24 bit PCM; 48 or 96 kHz sample rate; selectable Network Latency. Protection: Soft & Peak limiting, Excursion Control & Thermal Regulation PF2-500R RHAON EMPOWERED AMPLIFIERS The PF2-500R is a RHAON empowered 500/200 W RMS bi-amplifier. It is identical to the PF1-500R except for also having a 200 Watt HF amplifier and associated electronic crossover. Power: 6 A @ 120 V, 3 A @ 240 V Idle current: 500 ma @ 120 V; 250 ma @ 240 V. Max inrush current: 1 A Note: All analog inputs and outputs comply with AES Standard 48-2005 on interconnecting, grounding and shielding. Page 7 CF/CFX Modular Point Source Array Renkus-Heinz, Inc. Headquarters, Foothill Ranch, California, USA Working together, there’s no problem we can’t solve, no schedule we can’t meet, no project we can’t take to a higher level of excellence, from the White House to the Olympic SuperDome, from corner churches to major metropolitan concert halls. Much as we love technology, our greatest satisfaction comes through helping people communicate through music, dance, theater, or the power of a new idea brilliantly expressed. When we make those kinds of connections, there’s nothing more exciting – or more powerful. Here are some of the unique Renkus-Heinz technologies we use in our loudspeaker systems: Patented CoEntrant Topology integrates midrange and high frequency drivers into wideband point sources. Complex Conic Topology, the first new approach to horn design in decades, has proven its superior performance worldwide. TRAP (TRue Array Principle) design aligns acoustic centers so loudspeaker clusters produce coherent output. Reference Point Array engineering optimizes the entire signal chain from line level to listener for unprecedented performance. Renkus-Heinz, Inc., 19201 Cook Street, Foothill Ranch, CA 92610-3501, USA Tel: 949-588-9997 • Fax: 949-588-9514 • [email protected] www.renkus-heinz.com RH690 November 2011 Sensitivity CF101LA-5, -5R & -52R: 1.0 V for rated power output CFX101LA & LA-8: 96 dB (1W/1m) TECHNICAL INFORMATION Power CF101LA-5, -5R & -52R: CFX101LA: CFX101LA-8 Controls: Max SPL: 126 dB peak Dispersion: 90 Horizontal, 15 Vertical O O Freq. Response: 60 Hz to 20 kHz HF Drivers: Two 1” SSDCDXI-1730-8 HF Neodymium drivers; 75 W RMS @ 8 Ohms, 150 W pgm each Enclosure: Multi-ply hardwood, perforated metal grille Power: Freq. Resp: THD Distortion: Hum & Noise: Damping: Input: Sensitivity: CMR: A New Concept - Point Source Line Arrays Connectors: CFX101LA-8: Neutrik 4-pin Speakon style connectors, Screw terminals Finish: Black or white Hardware: Four Metric M10 attachment points Multi-angle pole socket LF Driver: CF101LA & CFX101LA: 10” Neodymium woofer, model SSL10-10, 250 W RMS @ 4 Ohms, 500 W pgm CFX101LA-8: 10” Neodymium woofer, model SSL10-8, 250 W RMS @ 8 Ohms, 500 W pgm Crossover: 1700 Hz Line Array Systems 115 V AC or 230 V AC, 50/60 Hz 500 W pgm at 4 Ohms 500 W pgm at 8 Ohms Array balancing Associated Hardware: RHANG101LA flybar POLE-CF101 mounting pole In small venues a single cabinet offers 90O horizontal coverage and a narrow 15O vertical pattern, ideal for many small venues. Additional cabinets add vertical coverage in 15O increments.multiple cabinets can be ground stacked, pole mounted or flown, either with or without matching subwoofers. Dimensions: 13" H x 23 3/4" W x 15" D (33 cm x 60.3 cm x 38.1cm) Weight CF101LA-5 & -5R: 47 1/2 Lbs. (20.7 Kg) net CF101LA-52R: 48 1/2 Lbs (22 Kg) net CFX101LA & LA-8: 42 1/2 Lbs (19.3 Kg) net Controls: Power Connector: Input: Power Gain (screwdriver adjustable) IEC Power connector Looping XLR; female in, male out (pin 1 chassis, pin 2 +, pin 3 -) Switchable, 115 or 230 V AC, 50/60 Hz 5 A @ 120 V, 2.5 A @ 240 V Idle current: 400 ma @120 V; 200 ma @ 240 V Max inrush current: 1 A The PF1-500R is identical to the PF1-500 except for the addition of the RHAON Network Interface; additional capabilities include: The PF2-500R is a RHAON empowered 500/200 W RMS bi-amplifier. It is identical to the PF1-500R except for also having a 200 Watt HF amplifier and associated electronic crossover. For additional details on the RHAON Audio Operations Network, refer to www.renkus-heinz.com/Rhaon/Index.html. • Outdoor events; corporate picnics, political rallies, etc. The self-powered CF101LA and the non-powered CFX101LA are the basic building blocks in the Renkus-Heinz CF/CFX family of point source line array systems. Their unique design allows arrays of all sizes to be quickly and easily assembled and safely and securely installed. HF Balance Control 15” An adjustable HF balance control allows adjustment of the HF output of individual modules in multi-module arrays to maintain the natural balance between high and low frequencies and make sure every member of the audience receives the same well balanced sound. Note: The cabinet is shown without its protective metal grille. Multi-angle Pole Socket, Bottom Mounted For more detailed dimensional information, please refer to the 2D and 3D drawing files on our website, www.renkus-heinz.com. 2 1/2” Intelligent Amplifiers 23 3/4” The intelligent amplifiers integral to the CF101LA are a new kind of electronics system. They combine Class D digital amplification with comprehensive signal processing into a single lightweight unit. Protection, crossovers and parametric EQ are integrated into the signal path. 7 1/2º 13” Renkus-Heinz, Inc., 19201 Cook Street, Foothill Ranch, CA 92610-3501, USA Tel: +1 949-588-9997 • Fax: +1 949-588-9514 • [email protected] • www.renkus-heinz.com RH 696 Rev B Modular Point Source Line Arrays • Live sound reinforcement in small and medium size venues; auditoriums, night clubs, houses of worship, etc. CF/CFX101LA Point Source Line Array Modules DIMENSIONAL INFORMATION 7” Non-Powered Typical CF101LA/CFX101LA Point Source Line Array 6 A @ 120 V, 3 A @ 240 V Idle current: 500 ma @ 120 V; 250 ma @ 240 V. Max inrush current: 1 A Note: All analog inputs and outputs comply with AES Standard 48-2005 on interconnecting, grounding and shielding. Metric M10 Attachment Point (Typical for 4) CFX101LA • Virtually any application where outstanding sonic performance is required and sound level and coverage needs cannot be satisfied with conventional loudspeaker systems. PF2-500R RHAON EMPOWERED AMPLIFIERS Power: Self-Powered Applications PF1-500R RHAON EMPOWERED AMPLIFIERS Inputs: CobraNet: Dual RJ45 connectors; accept Cat 5 copper cable. AES/EBU: Phoenix connectors; Analog: Phoenix connectors Digital Format: 16, 20 or 24 bit PCM; 48 or 96 kHz sample rate; selectable Network Latency. Protection: Soft & Peak limiting, Excursion Control & Thermal Regulation CF101LA Both self-powered and non-powered models are available; RHAON, the Renkus-Heinz Audio Operations Network, is an option. It places total control and supervision of the loudspeaker system on your computer at your fingertips, no matter how far away you are. PF1-500 DIGITAL AMPLIFIER 500 W RMS @ 4 Ohms +0.0, -.5 dB, 20 Hz to 20 kHz < 0.02% typical <100 dB (A weighted) >100 10K Ohm balanced differential 1.0 V for RPO 74 dB CF/CFX101LA point source line arrays deliver the performance and pattern control of line arrays with the clarity of point source systems. Designed with portability and versatility in mind, they are equally at home in portable applications and permanent installations. They represent the ideal solution to the sound problems of many small and medium size venues. May 2011 RHAON empowers you with a new level of control over your loudspeaker system. It adds on-board DSP control of each loudspeakers EQ and level, on-going supervision of critical operating parameters and digital audio distribution - all over a standard Ethernet network. • Outstanding Performance Provide point source clarity with the pattern control and high level performance of line arrays. • Dual 1” HF Drivers and High Power 10” Woofer With Neodymium magnets deliver smooth, low distortion 126 dB peak SPL performance from 60 Hz to 20 kHz. • Great Versatility Can be used as a stand-alone loudspeaker or as an array module in a ground stacked, pole mounted or flown point source line array. • Exclusive Tuned Conic Diverter Provides constant beamwidth / directivity down to 300 Hz. • Tight Pattern Control Single cabinets provide 90O horizontal and 15O vertical coverage; additional cabinets increase vertical coverage in 15O increments. • Reliable, Easy-To-Use Hardware Assemble easily, safely stack or fly multi-cabinet arrays and subwoofers. • Flexible Input Configurations Choose passive inputs, or go self-powered with either the PF1-500 amplifier or the RHAON empowered PF1-500R or PF2-500R bi-amplifier. © 2011 Renkus-Heinz Inc. reserves the right to change any product specification without prior notification. ADVANCED AUDIO TECHNOLOGY VERSATILE Advanced Audio Technology INNOVATIVE DESIGN Safe & Simplified Hardware The Tuned Conic Converter Designed for power, portability and versatility, CF/CFX101LA modular point source line array systems from Renkus-Heinz are the ideal solution for today's small and mid-sized venues, including auditoriums, night clubs, theaters and houses of worship. Line arrays rely upon their ability to convert the spherical wavefront of a typical loudspeaker into a planar (flat) wavefront that couples coherently with the output of adjacent modules to create a plane wave. Plane waves diminish less rapidly over distance (3 dB loss for every doubling of distance) than spherical waves that decay 6 dB every time the distance doubles. CF101LA / CFX101LA Point Source Line Array Module Our new Tuned Conic Diverter carefully shapes the curvature of the wavefront within the horn so that it's curvature matches the curvature of the array and couples seamlessly with adjacent modules. Suited equally to fixed installation or portable applications the full range cabinets offer consistent 90o horizontal and tight 15o vertical coverage. Their controlled coverage pattern allows them to outperform larger 12” and 15” loudspeakers in many applications as their output can be directed onto the audience instead of into the walls and ceiling. Individual full range cabinets can be stacked or arrayed with each cabinet increasing the vertical coverage by 15o degrees. Up to four full-range modules can be ground stacked to provide a 90o by 60o coverage pattern with up to 9 dB more output and tighter vertical pattern control than a conventional single cabinet. Traditional line arrays require two or three times as many cabinets to provide the same range of coverage and control. The CF/CFX101LA point source line array modules and matching subwoofers have been designed with portability and flexibility in mind. Alone or combined with the matching CF/CFX15S 15” subwoofer,up to 6 full-range CF/CFX101LA modules can be flown, making them the perfect solution for a wide range of installed systems or portable sound needs. The possible combinations and applications are almost endless. Neodymium magnets on the single 10" low frequency woofer and dual 1" High Frequency compression drivers provide the ideal balance of power and portability, while the revolutionary performance of the Tuned Conic Diverter waveguide ensures the smoothest possible transition between cabinets. Simple, rugged, integral hardware allows for maximum versatility, maximum safety, and fast setup and teardown. When it comes to innovation, once again Renkus-Heinz leads the way. With the flexibility to be flown, ground-stacked or pole-mounted, the modular CF/CFX101LA point source line array systems deliver the high level performance and pattern control of a line array, with the clarity of a point source system, in a compact, sleek and affordable design that's equally at home as a portable system or in a permanent installation. Individual full range cabinets can be used as a stand-alone system, either with or without an associated subwoofer. They can be flown using Metric M10 eye-bolts or pole mounted on a matching subwoofer or standard loudspeaker tripod stand. A multi-angled pole socket allows them to be aimed stright ahead or angled up or down. FLEXIBLE HARDWARE CF101LA/CFX101LA Point Source line Array with matching subwoofer CF101LA and CFX101LA point source line arrays are true point source line array systems offering the benefits of both point source loudspeakers and line arrays. Metric M10 attachment points allow individual modules to be easily flown with eye bolts. Multiple full range modules can be ground stacked or pole mounted using the matching subwoofer as a base Up to 6 modules and two subwoofers can be flown. The array modules and subwoofers are joined together with heavy-duty tie bars and quick-disconnect pins that provide easy assembly along with metal-to-metal reliability. The matching subwoofers employ the same simple yet sturdy hardware enabling full range array modules to be flown beneath the subwoofer. An associated flybar that attaches easily to the subwoofer completes the package. As sound progresses through the horn, it's wavefront is progressively manipulated, passing through a tuned conic diverter, slowing the wavefront's expansion in the center and modifying its curvature to match the shape of the cabinet. CF/CFX101LA hardware has been designed to work either way so left and right systems can be setup symmetrically without the need for mirror image cabinets. HF Balance Control Multi-Angle Pole Sockets An adjustable HF balance control panel on each full range module allows you to adjust the high frequency output of each module to compensate for the changes in high frequency coupling that occurs between adjacent modules in multi-module line arrays. Multi-angle 35 mm pole sockets allow CF101LA and CFX101LA array modules to be mounted on standard loudspeaker stands or on heavy duty pole mounts attached to an associated CF15S or CFX15S subwoofer. The multi-angle socket allows the cabinet to be aimed straight ahead or angled up or down depending on the needs of the venue. It is invaluable in helping you assure that every member of the audience receives the same well balanced sound, even those seated in the rear of the audience area. Renkus-Heinz Audio Operations Network RHAON is the first practical system to combine individual loudspeaker control and supervision of self-powered loudspeaker systems with digital audio distribution. RHAON puts you in total control of: – A powerful DSP inside each loudspeaker on the Ethernet network that includes eight bands of parametric EQ, high and low frequency shelving filters, input level control, muting and up to 340 ms of delay. – Monitoring of each loudspeakers critical operating parameters such as signal clipping, amplifier output voltage and current and temperature with automatic alert functions. – Real time digital audio distribution over standard Ethernet networks using proven CobraNet technology to deliver multiple channels of high quality digital audio over a CAT 5 cable. Ground Stack with dual array modules & single subwoofer CF101LA/CFX101LA Point Source Line Arrays Floor System with single array module & subwoofer Floor System with dual array modules & dual subwoofers CF101LA/CFX101LA Point Source Line Arrays ADVANCED AUDIO TECHNOLOGY VERSATILE Advanced Audio Technology INNOVATIVE DESIGN Safe & Simplified Hardware The Tuned Conic Converter Designed for power, portability and versatility, CF/CFX101LA modular point source line array systems from Renkus-Heinz are the ideal solution for today's small and mid-sized venues, including auditoriums, night clubs, theaters and houses of worship. Line arrays rely upon their ability to convert the spherical wavefront of a typical loudspeaker into a planar (flat) wavefront that couples coherently with the output of adjacent modules to create a plane wave. Plane waves diminish less rapidly over distance (3 dB loss for every doubling of distance) than spherical waves that decay 6 dB every time the distance doubles. CF101LA / CFX101LA Point Source Line Array Module Our new Tuned Conic Diverter carefully shapes the curvature of the wavefront within the horn so that it's curvature matches the curvature of the array and couples seamlessly with adjacent modules. Suited equally to fixed installation or portable applications the full range cabinets offer consistent 90o horizontal and tight 15o vertical coverage. Their controlled coverage pattern allows them to outperform larger 12” and 15” loudspeakers in many applications as their output can be directed onto the audience instead of into the walls and ceiling. Individual full range cabinets can be stacked or arrayed with each cabinet increasing the vertical coverage by 15o degrees. Up to four full-range modules can be ground stacked to provide a 90o by 60o coverage pattern with up to 9 dB more output and tighter vertical pattern control than a conventional single cabinet. Traditional line arrays require two or three times as many cabinets to provide the same range of coverage and control. The CF/CFX101LA point source line array modules and matching subwoofers have been designed with portability and flexibility in mind. Alone or combined with the matching CF/CFX15S 15” subwoofer,up to 6 full-range CF/CFX101LA modules can be flown, making them the perfect solution for a wide range of installed systems or portable sound needs. The possible combinations and applications are almost endless. Neodymium magnets on the single 10" low frequency woofer and dual 1" High Frequency compression drivers provide the ideal balance of power and portability, while the revolutionary performance of the Tuned Conic Diverter waveguide ensures the smoothest possible transition between cabinets. Simple, rugged, integral hardware allows for maximum versatility, maximum safety, and fast setup and teardown. When it comes to innovation, once again Renkus-Heinz leads the way. With the flexibility to be flown, ground-stacked or pole-mounted, the modular CF/CFX101LA point source line array systems deliver the high level performance and pattern control of a line array, with the clarity of a point source system, in a compact, sleek and affordable design that's equally at home as a portable system or in a permanent installation. Individual full range cabinets can be used as a stand-alone system, either with or without an associated subwoofer. They can be flown using Metric M10 eye-bolts or pole mounted on a matching subwoofer or standard loudspeaker tripod stand. A multi-angled pole socket allows them to be aimed stright ahead or angled up or down. FLEXIBLE HARDWARE CF101LA/CFX101LA Point Source line Array with matching subwoofer CF101LA and CFX101LA point source line arrays are true point source line array systems offering the benefits of both point source loudspeakers and line arrays. Metric M10 attachment points allow individual modules to be easily flown with eye bolts. Multiple full range modules can be ground stacked or pole mounted using the matching subwoofer as a base Up to 6 modules and two subwoofers can be flown. The array modules and subwoofers are joined together with heavy-duty tie bars and quick-disconnect pins that provide easy assembly along with metal-to-metal reliability. The matching subwoofers employ the same simple yet sturdy hardware enabling full range array modules to be flown beneath the subwoofer. An associated flybar that attaches easily to the subwoofer completes the package. As sound progresses through the horn, it's wavefront is progressively manipulated, passing through a tuned conic diverter, slowing the wavefront's expansion in the center and modifying its curvature to match the shape of the cabinet. CF/CFX101LA hardware has been designed to work either way so left and right systems can be setup symmetrically without the need for mirror image cabinets. HF Balance Control Multi-Angle Pole Sockets An adjustable HF balance control panel on each full range module allows you to adjust the high frequency output of each module to compensate for the changes in high frequency coupling that occurs between adjacent modules in multi-module line arrays. Multi-angle 35 mm pole sockets allow CF101LA and CFX101LA array modules to be mounted on standard loudspeaker stands or on heavy duty pole mounts attached to an associated CF15S or CFX15S subwoofer. The multi-angle socket allows the cabinet to be aimed straight ahead or angled up or down depending on the needs of the venue. It is invaluable in helping you assure that every member of the audience receives the same well balanced sound, even those seated in the rear of the audience area. Renkus-Heinz Audio Operations Network RHAON is the first practical system to combine individual loudspeaker control and supervision of self-powered loudspeaker systems with digital audio distribution. RHAON puts you in total control of: – A powerful DSP inside each loudspeaker on the Ethernet network that includes eight bands of parametric EQ, high and low frequency shelving filters, input level control, muting and up to 340 ms of delay. – Monitoring of each loudspeakers critical operating parameters such as signal clipping, amplifier output voltage and current and temperature with automatic alert functions. – Real time digital audio distribution over standard Ethernet networks using proven CobraNet technology to deliver multiple channels of high quality digital audio over a CAT 5 cable. Ground Stack with dual array modules & single subwoofer CF101LA/CFX101LA Point Source Line Arrays Floor System with single array module & subwoofer Floor System with dual array modules & dual subwoofers CF101LA/CFX101LA Point Source Line Arrays Sensitivity CF101LA-5, -5R & -52R: 1.0 V for rated power output CFX101LA & LA-8: 96 dB (1W/1m) TECHNICAL INFORMATION Power CF101LA-5, -5R & -52R: CFX101LA: CFX101LA-8 Controls: Max SPL: 126 dB peak Dispersion: 90 Horizontal, 15 Vertical O O Freq. Response: 60 Hz to 20 kHz HF Drivers: Two 1” SSDCDXI-1730-8 HF Neodymium drivers; 75 W RMS @ 8 Ohms, 150 W pgm each Enclosure: Multi-ply hardwood, perforated metal grille Power: Freq. Resp: THD Distortion: Hum & Noise: Damping: Input: Sensitivity: CMR: A New Concept - Point Source Line Arrays Connectors: CFX101LA-8: Neutrik 4-pin Speakon style connectors, Screw terminals Finish: Black or white Hardware: Four Metric M10 attachment points Multi-angle pole socket LF Driver: CF101LA & CFX101LA: 10” Neodymium woofer, model SSL10-10, 250 W RMS @ 4 Ohms, 500 W pgm CFX101LA-8: 10” Neodymium woofer, model SSL10-8, 250 W RMS @ 8 Ohms, 500 W pgm Crossover: 1700 Hz Line Array Systems 115 V AC or 230 V AC, 50/60 Hz 500 W pgm at 4 Ohms 500 W pgm at 8 Ohms Array balancing Associated Hardware: RHANG101LA flybar POLE-CF101 mounting pole In small venues a single cabinet offers 90O horizontal coverage and a narrow 15O vertical pattern, ideal for many small venues. Additional cabinets add vertical coverage in 15O increments.multiple cabinets can be ground stacked, pole mounted or flown, either with or without matching subwoofers. Dimensions: 13" H x 23 3/4" W x 15" D (33 cm x 60.3 cm x 38.1cm) Weight CF101LA-5 & -5R: 47 1/2 Lbs. (20.7 Kg) net CF101LA-52R: 48 1/2 Lbs (22 Kg) net CFX101LA & LA-8: 42 1/2 Lbs (19.3 Kg) net Controls: Power Connector: Input: Power Gain (screwdriver adjustable) IEC Power connector Looping XLR; female in, male out (pin 1 chassis, pin 2 +, pin 3 -) Switchable, 115 or 230 V AC, 50/60 Hz 5 A @ 120 V, 2.5 A @ 240 V Idle current: 400 ma @120 V; 200 ma @ 240 V Max inrush current: 1 A The PF1-500R is identical to the PF1-500 except for the addition of the RHAON Network Interface; additional capabilities include: The PF2-500R is a RHAON empowered 500/200 W RMS bi-amplifier. It is identical to the PF1-500R except for also having a 200 Watt HF amplifier and associated electronic crossover. For additional details on the RHAON Audio Operations Network, refer to www.renkus-heinz.com/Rhaon/Index.html. • Outdoor events; corporate picnics, political rallies, etc. The self-powered CF101LA and the non-powered CFX101LA are the basic building blocks in the Renkus-Heinz CF/CFX family of point source line array systems. Their unique design allows arrays of all sizes to be quickly and easily assembled and safely and securely installed. HF Balance Control 15” An adjustable HF balance control allows adjustment of the HF output of individual modules in multi-module arrays to maintain the natural balance between high and low frequencies and make sure every member of the audience receives the same well balanced sound. Note: The cabinet is shown without its protective metal grille. Multi-angle Pole Socket, Bottom Mounted For more detailed dimensional information, please refer to the 2D and 3D drawing files on our website, www.renkus-heinz.com. 2 1/2” Intelligent Amplifiers 23 3/4” The intelligent amplifiers integral to the CF101LA are a new kind of electronics system. They combine Class D digital amplification with comprehensive signal processing into a single lightweight unit. Protection, crossovers and parametric EQ are integrated into the signal path. 7 1/2º 13” Renkus-Heinz, Inc., 19201 Cook Street, Foothill Ranch, CA 92610-3501, USA Tel: +1 949-588-9997 • Fax: +1 949-588-9514 • [email protected] • www.renkus-heinz.com RH 696 Rev B Modular Point Source Line Arrays • Live sound reinforcement in small and medium size venues; auditoriums, night clubs, houses of worship, etc. CF/CFX101LA Point Source Line Array Modules DIMENSIONAL INFORMATION 7” Non-Powered Typical CF101LA/CFX101LA Point Source Line Array 6 A @ 120 V, 3 A @ 240 V Idle current: 500 ma @ 120 V; 250 ma @ 240 V. Max inrush current: 1 A Note: All analog inputs and outputs comply with AES Standard 48-2005 on interconnecting, grounding and shielding. Metric M10 Attachment Point (Typical for 4) CFX101LA • Virtually any application where outstanding sonic performance is required and sound level and coverage needs cannot be satisfied with conventional loudspeaker systems. PF2-500R RHAON EMPOWERED AMPLIFIERS Power: Self-Powered Applications PF1-500R RHAON EMPOWERED AMPLIFIERS Inputs: CobraNet: Dual RJ45 connectors; accept Cat 5 copper cable. AES/EBU: Phoenix connectors; Analog: Phoenix connectors Digital Format: 16, 20 or 24 bit PCM; 48 or 96 kHz sample rate; selectable Network Latency. Protection: Soft & Peak limiting, Excursion Control & Thermal Regulation CF101LA Both self-powered and non-powered models are available; RHAON, the Renkus-Heinz Audio Operations Network, is an option. It places total control and supervision of the loudspeaker system on your computer at your fingertips, no matter how far away you are. PF1-500 DIGITAL AMPLIFIER 500 W RMS @ 4 Ohms +0.0, -.5 dB, 20 Hz to 20 kHz < 0.02% typical <100 dB (A weighted) >100 10K Ohm balanced differential 1.0 V for RPO 74 dB CF/CFX101LA point source line arrays deliver the performance and pattern control of line arrays with the clarity of point source systems. Designed with portability and versatility in mind, they are equally at home in portable applications and permanent installations. They represent the ideal solution to the sound problems of many small and medium size venues. May 2011 RHAON empowers you with a new level of control over your loudspeaker system. It adds on-board DSP control of each loudspeakers EQ and level, on-going supervision of critical operating parameters and digital audio distribution - all over a standard Ethernet network. • Outstanding Performance Provide point source clarity with the pattern control and high level performance of line arrays. • Dual 1” HF Drivers and High Power 10” Woofer With Neodymium magnets deliver smooth, low distortion 126 dB peak SPL performance from 60 Hz to 20 kHz. • Great Versatility Can be used as a stand-alone loudspeaker or as an array module in a ground stacked, pole mounted or flown point source line array. • Exclusive Tuned Conic Diverter Provides constant beamwidth / directivity down to 300 Hz. • Tight Pattern Control Single cabinets provide 90O horizontal and 15O vertical coverage; additional cabinets increase vertical coverage in 15O increments. • Reliable, Easy-To-Use Hardware Assemble easily, safely stack or fly multi-cabinet arrays and subwoofers. • Flexible Input Configurations Choose passive inputs, or go self-powered with either the PF1-500 amplifier or the RHAON empowered PF1-500R or PF2-500R bi-amplifier. © 2011 Renkus-Heinz Inc. reserves the right to change any product specification without prior notification. CF/CFX Series Commanding Performance, Compelling Value Sound that makes performances and audiences truly come alive doesn’t come easy. But CF/CFX series loudspeakers put the power of unique Renkus-Heinz developments like Complex Conic horns to work for you. Versatile enclosure designs, go-anywhere hardware and rugged construction help solve your sound reinforcement challenges easily and quickly. Advanced options like intelligent onboard amplification and RHAON — the Renkus-Heinz Audio Operations Network — help you build sophisticated sound systems that are easy to use. CF15S CFX15S-8 Self-Powered Non-Powered Modular Point Source Line Array 15” Subwoofers CF15S and CFX15S-8 subwoofers were developed as companion pieces to the CF/CFX series point source line array modules. They provide the high impact sub bass energy needed in many venues and also serve as a mounting platform for both stacked and flown arrays. Applications • Virtually any application where high-output, low frequency content is required CF15S/CFX15S-8 Subwoofer Permanent Installations • High quality music/speech systems and surround systems for houses of worship, schools, performing art centers, night clubs, etc. Portable Applications • Live music reinforcement, DJ systems, houses of worship, schools, etc. PF Series Intelligent Amplifiers Passive, powered or networked, you can choose the system configuration that meets your needs at any time. At the factory or in the field, the CFX passive connector plate can be easily replaced by a PF1 series intelligent Class D digital amplifier. The lightweight switching power supply used in the PF1 series is over 70% efficient at full output. Their high efficiency reduces AC power requirements and eliminates the need for a cooling fan. Whenever you are ready for Ethernet audio networking, your CF/CFX loudspeakers are too; just replace the connector plate with a RHAON empowered PF1-500R amplifier equipped for connection to the Renkus-Heinz Audio Operations Network. RHAON empowers you with full control over digital audio distribution, loudspeaker-specific DSP and control/monitoring – all using standard Ethernet hardware and cabling. If you need an outstanding high-power 15-inch subwoofer, order the CFX15S-8 or CF15S-5. If you need Ethernet-based audio operations networking, order the CF15S-5R. CF15S/CFX15S-8 Subwoofer used as an array base CF15S/CFX15S-8 Subwoofer used in a flown array • Powerful 15” Subwoofers High impact 40 Hz to 120 Hz, 129 dB peak SPL sub-bass performance. • Outstanding Versatility Pole socket and flying hardware allow use as a mounting platform for both stacked and flown CF/CFX101LA-8 arrays. • Flexible Input Configurations Choose passive inputs, or go self-powered with the PF1 series intelligent amplifiers, with or without RHAON networking. • RHAON Renkus-Heinz Audio Operations Network All self-powered CF15S series subwoofers are available with RHAON for flexible digital signal distribution, loudspeaker management and control. • High Performance, High Power Woofers With long-throw Neodymium magnetic structures easily handle 800 Watts of program power. © 2011 Renkus-Heinz Inc. reserves the right to change any product specification without prior notification. TECHNICAL INFORMATION Sensitivity CF15S-5 & -5R: 1.0 V for RPO CFX15S-8 : 97 dB (1W/1m) Power CF15S-5 & -5R: CFX15S-8: Connectors CF15S-5 & -5R: CFX15S-8: Max SPL CF15S-5 & -5R: 127 dB peak CFX15S-8: 129 dB peak Freq. Resp: 40 Hz to 120 Hz 115 V AC or 230V AC 800 W pgm at 8 Ohms See amplifier specifications Screw terminals & looping 4-pin Neutrik Speakon style connectors Hardware: 8-point univ. mtg. hdw. (Metric M10 threads) Threaded pole socket, Integral flying hardware Optional - heavy duty wheels Dimensions: 19" H x 23 3/4” W x 22 1/2" D (48.3 cm x 60.3 cm x 56.5 cm) Weight CF15S-5 & -5R: 117 Lbs (53.4 Kg) net CFX15S-8: 112 Lbs (51 Kg) net LF Driver: CF15S: 15" woofer with Neodymium magnet, model SSL15-20; 400 W RMS @ 4 Ohms, 800 W pgm CFX15S-8: 15" woofer with Neodymium magnet, model SSL15-17; 400 W RMS @ 8 Ohms, 800 W pgm Enclosure: 13-ply hardwood, perforated metal grille Finish: Black or white PF1-500 DIGITAL AMPLIFIER Power: Freq. Resp: THD Distortion: Hum & Noise: Damping: Input: Sensitivity: CMR: Controls: Gain (screwdriver adjustable) Power Connector: IEC Power connector Input: Looping XLR; female in, male out (pin 1 chassis, pin 2 +, pin 3 -) Power Switchable, 115 or 230 V AC, 50/60 Hz 5 A @ 120 V, 2.5 A @ 240 V Idle current: 400 ma @120 V; 200 ma @ 240 V Max inrush current: 1 A PF1-500R RHAON EMPOWERED AMPLIFIER 500 W RMS @ 4 Ohms +0.0, -.5 dB, 20 Hz to 20 kHz < 0.02% typical <100 dB (A weighted) >100 10K Ohm balanced differential 1.0 V for RPO 74 dB The PF1-500R is identical to the PF1-500 except for the addition of the RHAON Network Interface; additional capabilities include: Protection: Soft & Peak limiting, Excursion Control & Inputs: CobraNet: Dual RJ45 connectors; accept Thermal Regulation Cat 5 copper cable. AES/EBU: Phoenix connectors; For additional details on the RHAON Audio Operations Network, refer to Analog: Phoenix connectors www.renkus-heinz.com/Rhaon/Index.html. Digital Format: 16, 20 or 24 bit PCM; 48 or 96 kHz sample rate; selectable Network Latency. Note: All analog inputs and outputs comply with AES Standard 48-2005 on interconnecting, grounding and shielding. Metric M10 Attachment Poiint (Typical for 8) 6 1/8” 11 1/4” DIMENSIONAL INFORMATION Note: The enclosure is shown without its metal grille. Threaded Pole Socket 22 1/2” 6 1/8” For more detailed dimensional information, please refer to the 2D and 3D drawing files on our website, www.renkus-heinz.com 2 1/2” 11 7/8” 23 3/4” 19” Renkus-Heinz, Inc., 19201 Cook Street, Foothill Ranch, CA 92610-3501, USA Tel: +1 949-588-9997 • Fax: +1 949-588-9514 • [email protected] • www.renkus-heinz.com RH 697 Rev A February 2011