Transcript
Installation
32" Flat Panel Display Package
Unpacking the flat panel screen
Power Cord
MUTE
TV
Audio Cable
DVI-D to HDMI cable
POWER
INPUT
I/II
LIST Q.VIEW MENU
PR
OK VOL
VOL PR
1
2
4
5
7
8
9
SSM
0
PSM
SLEEP
ARC
UPDATE
3 6
TEXT TIME
SIZE
MIX
HOLD
REVEAL ?
INDEX i
MODE M
Remote Control/ Batteries (AAA x 2)
Monitor
Speaker Set
User Guide CD
Set top bracket* With velcro for monitor fixation, and cable strap. *If this Flat Panel Display Package has been purchased together with a TANDBERG Edge MXP system, there is no need for this set top bracket. The TANDBERG Edge MXP package will include a separate bracket for the PrecisionHD camera.
Table stand kit
Tool needed for the installation: - Screwdriver PH 2
Screw kit for table stand and different types of walls; gypsum/wood, concrete, brick
Wall mount kit With cable strap
Wall mount rail
Wall brackets
D13803.06 Page 1
Installation
32" Flat Panel Display Package
Connecting Cables
DVI-D to HDMI Cable
Audio Cable PC Stereo IN
Bilde nr 6
AC in HDMI
Audio (RGB/DVI)
Monitor Configuration Recommended maximum volume on the monitor is 65 out of 100. Source input: HDMI/DVI
D13803.06 Page 2
Wall mount
32" Flat Panel Display Package 2. Use the inlay from the monitor packaging as temporary stand. Mount the wall brackets, using four screws.
1. Lay the monitor on a clean surface, mount the speakers.
3. Bend the bracket into correct shape and fix onto the monitor.
4. Place Set Top onto bracket.
Make sure the velcro strips are matched properly!
Overhang of Set Top and bracket is needed for cable space towards wall. Maximum 7 cm.
5. Connect cables (see page 2) and fixate in cable strap.
6. Wall mounting: Make sure to follow instructions on next page according to wall type: A - Wooden pillars (gypsum wall) 60 cm center - center B - Wooden pillars (gypsum wall) 16 in (41 cm center - center) C - Brick/concrete wall Warning! Due to the size and mass of this equipment, it is very important that the wall mount unit is safely installed according to the installation instructions. It is highly recommended that the installation is provided by persons with appropriate technical training.
D13803.06 Page 3
Wall mount 6 A) Wooden pillars (w/gypsum) 60 cm center-center.
32" Flat Panel Display Package 6 B) Wooden pillars (w/gypsum) 16 inch center-center.
Mount into specified holes with screws only
Mount into specified holes with screws only
7 Hook the system onto the wall mount rail.
6 C) Brick/Concrete wall.
1
2
Ø 3,0 mm (0,1”)
Ø 8,0 mm (0,31”)
1.
Drill a small initial hole
2.
Drill a larger hole for plugs
3.
Mount into specified holes with plugs and screws
8 Fixate cables along the wall.
> 1,5 m > 1,5 m =
60 mm
D13803.06 Page 4
Recommended safety height to keep Set Top and other falling parts out of reach for children.
Table stand 1. Place monitor onto table stand.
3. Mount the speakers with the four screws attached.
32" Flat Panel Display Package 2. Secure the table stand with the six M4x10 screws into assigned holes. Make sure to screw all the way until tight!
4. Bend the bracket into correct shape and fix onto the monitor.
Make sure the velcro strips are matched properly!
D13803.06 Page 5
Table stand
32" Flat Panel Display Package
5. Place Set Top onto bracket.
Place bracket and Set Top along edge of monitor
6. Connect cables (see page 2) and fixate in cable straps.
7. This is NOT a floor-standing system. Place the system on a flat and rigid surface or table.
D13803.06 Page 6
