Transcript
PRODUCT SPECIFICATIONS
2462 Extra Large Convection Wood Stove (717 mm)
(840 mm)
ACTUAL DIMENSIONS
Unit Depth: 18 1/4” (467 mm) Unit Height: 33” (840 mm) Unit Width: 28 1/4” (717 mm)
(690 mm) (467 mm)
TECHNICAL INFORMATION
Log Length: up to 25” (640 mm) Burn Time: up to 12 hours Heating Capacity: up to 2,400 sq. ft. (224 m2) Maximum Heat Output: 55,000 BTUs/hr. Efficiency Rating: 74% EPA Emissions Rating: 1.3 grams/hr. Weight: 634 lbs. (288 kg) Flue Collar: 8” (203.2 mm) round, reversible Firebox Volume: 3.3 cubic feet (.09 m3) Clearances (with optional shields) Back: 18” (457.2 mm) measured to back of stove top Corner: 17” (430 mm) Side: 20” (510 mm)
(840 mm) (763 mm)
FIELD INSTALLED ACCESSORIES • • • • • • •
Dual speed convection fan Rear heat shield Fan thermostat Fan rheostat Short legs - 2” (50.8 mm) height Stove surface thermometer Warming shelf
(430 mm) A Brand of Monessen Hearth Systems Co. 149 Cleveland Drive, Paris, Kentucky 40361
www.monessenhearth.com
PRODUCT SPECIFICATIONS
2462 Extra Large Convection Wood Stove (CONTINUED)
STOVE CLEARANCES UNPROTECTED SURFACE3 PROTECTED SURFACE3 Corner Corner Parallel Installation Installation Parallel Installation Installation Side (A) Rear (B) Corner (C) Side (D) Rear (E) Corner (F)
No heat shields 20” 23” 18” 18” 18” 17” (510 mm) (580 mm) (460 mm) (460 mm) (460 mm) (430 mm) Rear exit, rear heat shield only
20” (510 mm)
18” (460 mm)
N/A
18” (460 mm)
12” (300 mm)
N/A
Top exit, rear heat shield only1
20” (510 mm)
23” (580 mm)
18” (460 mm)
18” (460 mm)
18” (460 mm)
17” (430 mm)
Top exit, rear heat 20” 18” 17” 18” 12” 15” shield, single wall, (510 mm) (460 mm) (430 mm) (460 mm) (300 mm) (380 mm) connector shields1,2 Top exit, rear heat 20” 14” 16” 18” 12” 15” shield, double wall1 (510 mm) (360 mm) (410 mm) (460 mm) (300 mm) (380 mm)
Stove installed parallel to wall
Stove installed in corner
Stove installed parallel
Stove installed in corner
Shielding for a top exit stove must include a shield insert to protect the area behind the flue collar.
1
Chimney connector heat shields must extend exacty 24” (610 mm) above the clue collar of the stove.
2
All installations venting straight up to a factory built chimney require a 24” (610 mm) diameter or square ceiling heat shield. The ceiling heat shield should be 24 gauge sheet metal or equivalent mounted on 1” (25 mm) non-combustible spacers 1” (25 mm) below the ceiling.
3
To avoid personal injury or property damage, the product described by this brochure must be installed, operated and maintained in strict compliance with the instructions packaged with the product and all applicable building or fire codes. Contact local building or fire officials about restrictions and installation inspection requirements. All photographs and drawings on this brochure are for illustrative purposes only and are not intended for, nor should they be used as a substitute for the instructions packaged with the unit. Appearance and specifications of the product are subject to change without notice. © 2011 Monessen Hearth Systems Co. 0611v.1
